EhS 45° Twin Anchor System - Peter Eisenreich
2
tight meshes - no problem ! The optimal reanchoring system to support frames for one-sided wall formwork ! quick and simple installation done by 1 person only within less than one minute one pieced anchor - no additional couplers or 45° - holders requested no removing protruding tie rods - a minimum of refinishing only installation into meshes more than 70 mm without any problem no opening and welding reinforcements subsequently position can be treated by a finishing trowel or a screed board and recognized again reanchoring out of walls - installation in wall formwork - no more drilling through formwork panels! Twin Anchors DW15 / DW20 G - Type : Due to stricter static requirements reinforcements in floor slabs are being placed closer increasingly. Installing loop anchors or similar inlets is becoming more difficult and time consuming. Our “Twin Anchors 45°” are the solution offering these benefits : Couplers and 45°- holders no more needed a minimum of refinishing work no tie rods to cut perm. loads P 45° "Twin Anchor” DW 15: 2 2 x 85 kN/17 N/mm 2 2 x 90 kN/30 N/mm "Twin Anchor” DW 20: 2 2 x 140 kN/30 N/mm Tension Tests in 45°-angularity Test Report No. 21 0686 0 98 EhS 45° "Twin Anchor" System 2015/03 S p e z i a l - B a u a r t i k e l t h e alternative to a loop anchor ! S p e z i a l - B a u a r t i k e l For more information request installation instruction 45°
Transcript of EhS 45° Twin Anchor System - Peter Eisenreich
Available in versions with c.-to-c. distance in 23 or 30 cm for DW15 and with 35 cms for DW20 and versions
for installment in tighter positions such as precast ceilings, and in different angularity.
For employment thread rods in DW26.5 see our product range “Hercules” DW 26.5.
tight meshes - no problem !
The optimal reanchoring system to support frames for one-sided wall formwork !
quick and simple installation
done by 1 person only within less than one minute
one pieced anchor - no additional couplers or 45° - holders requested
no removing protruding tie rods - a minimum of refinishing only
installation into meshes more than 70 mm without any problem
no opening and welding reinforcements subsequently
position can be treated
by a finishing trowel or a screed board and recognized again
reanchoring out of walls - installation in wall formwork -
no more drilling through formwork panels!
Twin Anchors DW15 / DW20 G - Type :Due to stricter static requirements reinforcements in floor slabs are being placed closer increasingly.
Installing loop anchors or similar inlets is becoming more difficult and time consuming.
Our “Twin Anchors 45°” are the solution offering these benefits :
Couplers and 45°- holders
no more needed
a minimum of
refinishing work
no tie rods
to cut
perm. loads P 45°
"Twin Anchor” DW 15:2
2 x 85 kN/17 N/mm2
2 x 90 kN/30 N/mm
"Twin Anchor” DW 20:2
2 x 140 kN/30 N/mm
Tension Tests in 45°-angularity Test Report No. 21 0686 0 98
EhS 45° "Twin Anchor" System2015/03
S p e z i a l - B a u a r t i k e l
t h e alternative to a loop anchor !
S p e z i a l - B a u a r t i k e l
For more information request installation instruction
45°
Sittenauer Thomas
Rectangle
Installation in wall formwork
reanchoring out of walls:
no more drilling
through the formwork panel
for
Available in versions with c.-to-c. distance in 23 or 30 cm for DW15 and with 35 cms for DW20 and versions
for installment in tighter positions such as precast ceilings, and in different angularity.
For employment thread rods in DW26.5 see our product range “Hercules” DW 26.5.
EhS 45° “Twin Anchor” System DW15 / G Febr. ’15
Twin Anchor DW15 / G
with 2 Recesses
S p e z i a l - B a u a r t i k e l
S p e z i a l - B a u a r t i k e l
Suspension Frames,
reanchored in
correct angularity 45°
Recesses leveled by a string Anchor Position before
removing Recesses
Application in slabs:
no hindrance to screed board
and power float
PE-45° Recess
For more information requestinstallation instruction.
Sittenauer Thomas
Rectangle
