Daylight solutionsEfficient and high-performanceKingspan Day-Lite systems

Insulated roof and wall systems

2

Table of contents

Kingspan Wall-Lite

Kingspan RooflightKingspan built-in light dome element

Insulated wall systems for transmission of daylight

Insulated roof systems

Kingspan Day-Lite window element

3

Healthy light at the workplace

It motivates, inspires the senses and is a natural means of perceiving the passage of time for our eyes: Daylight. However the natural brightness not only ensures a good mood, above all it also boosts capacity. Ultimately, on average a person spends approximately 80,000 hours of his life at the workplace. And precisely for this reason, the beautiful radiance from outside should also be permitted to penetrate into the interior of a building and here unfold its positive effect.

Through use of clever daylight systems that through their special characteristics let in natural light, in addition to improved lighting effects, there are many other positive repercussions on the human being and the work performed.

Daylight...

3 supports vision and reduces fatigue

3 promotes concentration and learning capacity

3 increases wellness and releases 'good-mood hormones'

3 increases safety at the workplace and reduces the error rate

3 helps prevent accidents

3 has positive health effects and reduces illness-related absence

Moreover, daylight in workplaces and production facilities is also worthwhile from the economic perspective. Installation of appropriate roof systems and elements reduces energy costs, since to some extent artificial light sources are dispensed with. Furthermore, fewer mechanical ventilation and heating systems are required and thus costs are sustainably reduced.

Let the sun in for better performance, a wellness climate and greater efficiency. With daylight systems from Kingspan.

The wellness factor – daylight: Let the sun in.

3 Comfort and increased production

3 Visual well-being

3 Health, vitality and performance

3 Improve the amenity values and significantly reduce overall energy requirements at the same time

3 Good lighting reduces symptoms of fatigue and lessens the probability of error

4

Kingspan Rooflight

3 Long service life

3 Lower energy consumption through U-values to 1.09 W/m2K

3 A visual highlight through flush-mount installation

3 Fast use of the building due to reduced construction times

3 High daylight yield even after 15 years *(= lower energy consumption) LT up to 65%

3 Minimal acquisition costs

3 Fast and easy planning

3 Function is guaranteed by the manufacturer

3 Interior work can proceed immediately after installation.

*Less than 3% reduction of the LT value after 15 years

Kingspan Rooflights enables a high daylight yield. These available light-permeable polycarbonate systems offer superior UV resistance; which in turn enables outstanding long-term light-permeability and first-class thermal and structural characteristic values.

Investor / planner

5

Clear installation advantages

3 Faster and easier installation

3 Low costs

3 One manufacturer; one point of contact

3 Total guarantee

3 Roof is immediately leak-proof

Dimensions, weight and performance

Product reference Thickness (mm)

Weight(kg/m2)

Length(incl. cak-cut 175 mm)

(m)

U-value(W/m2K)

LT value(%)* g value Fire behaviour

in acc. w. EN 13501-1

KS1000 PC 20 20 3.3 1.80 - 8.00 2.00 65 0.65 B-s2, d0

KS1000 PC 40 Double Skin 40 6.1 1.80 - 8.00 1.09 36 0.41 B-s2, d0

Notes:† Based on 80 mm panel thickness with spacers at 1 m centre-points.The U-values have been calculated using the method prescribed by national building guidelines.*For a transparent polycarbonate surface. Light transmission in accordance with BS EN 410 is measured samples 600 mm x 600 mm in size.The Solar Heat Gain Coefficient (SHGC) in accordance with BS EN 410 is the total solar energy that reaches the interior of a building. In addition to the standard assortment of the Kingspan Day-Lite colours, white is also available for a higher SHGC capacity. For additional information, please contract the Kingspan Technical Department.

Installer / processor

Applications

The Kingspan Rooflight is suitable for all building applications with a roof pitch of 7º or more after deformation, unless the humidity considerably increases through building occupants or processes, or for interior environments with low temperatures.

Kingspan Rooflights can also be used for wall applications, as needed. For additional project-specific information, please contract the Kingspan Technical Service Department.

333 mm 333 mm 333 mm

d D

D = d + 35 mm

35 mm

1 000 mm

dD

D = d + 35 mm

333 mm 333 mm 333 mm1 000 mm

Bonded metal strip plant-side

Profile geometry

KS1000 PC 20 Rooflight

KS1000 PC 40 Double Skin Rooflight

Note: Condensation can occur in the panel, this does not constitute a defect.

6

Kingspan built-in light dome element

3 Immediately rain-tight (interior work canbe directly performed)

3 Weather-independent

3 System guarantee

3 Function retention even after many years

3 Easy planning

3 Ready for the construction site as a complete installation unit

3 Ventilatable and available as NRWG in accordance withDIN EN 12101-2

3 Fulfi lls rigid roofi ng requirements as stipulated inDIN EN 18234

3 Optimal fi t thanks to factory-integration in the Kingspan roof panels

3 Leak-tightness thanks to a high degree of prefabrication

3 Elegant ceiling view through uniform profi ling of the inner shell

3 A complex apron plate is not required

3 Large bandwidth of RAL colour tones** * At least +5º C

** Colour deviations from the roof elements are possible

Investor / planner

7

Clear installation advantages

Installer / processor

3 Direct installation with the roof panels

3 Short installation times

3 Immediately leak-tight

3 Light dome pre-assembled in the factory

3 Everything from a single source

Note: The installation of support fl ashing in the area of the Roofl ight Domes is mandatory.

• Thermal-bridge free sash head thanks to PVC curb

• Max. length including cut-back 4,000 mm

• Min. roof pitch 6˚ / max. 25˚version with transverse joint

• Glazing variants: clear or opal

• U-values 3.0 – 0.9

• Opening variants: rigid, manual, electric

• Thermal-bridge free sash head thanks to PVC curb

• Max. length including cut-back 4,000 mm

• Min. roof pitch 6˚ / max. 25˚ version with transverse joint

• Reinforcements on all condensation-relevant points

• Version in diagonal geometry

• Delivery includes opening mechanism pneumatic and electric in accordance with DIN EN 12101-2 (connection through Essmann or other approved specialised companies)

Light dome elementsAeration and ventilation

For optimal light yield in your building

Light dome elementsRWA

Daylight in a manner appropriate for your fi re protection concept

Sizes / OKD

700 x 1,370 mm 1,200 x 1,200 mm

1,000 x 1,000 mm 1,500 x 1,500 mm

1,000 x 1,500 mm 1,200 x 2,400 mm

1,000 x 2,000 mm

Sizes / OKD

1,000 x 1,000 mm 1,000 x 1,500 mm

1,200 x 1,200 mm 1,000 x 2,000 mm

1,500 x 1,500 mm 1,200 x 2,400 mm

Longitudinal section and cross section through roof element and light dome

* other sizes are available on request

8

Kingspan Wall-Lite

3 Integrated system solution – joint compatible with allAWP facade elements

3 Enables a fl ush-mount facade appearancewithout structure frames

3 Structural, thermal and UV-resistancefor up to 25 years

3 Many colour options are available

3 Flush-mount glazing

3 No additional connection profi les

3 Easy planning

3 Low energy consumption

Kingspan Wall-Lite is a light-permeable polycarbonate wall light panel with concealed mounting that permits light to enter the building, with high thermal effi ciency and an aesthetic exterior. It off ers designers adequate freedom for designing really special and energy-effi cient buildings.

Investor / planner

9

Clear installation advantages

3 Direct installation without cut-out

3 Minimal time expenditure for installation

3 Easy installation

Applications

Kingspan Wall-Lite is a wall light panel with concealed mounting for vertical and horizontal applications. The system is completely compatible with all AWP wall panels.

Can be used for most industrial buildings.

Installer / processor

Dimensions, weight and performance

Product reference Thickness(mm)

Weight(kg/m2)

Standard lengths(m)*

U-value(W/m2K)

Light transmission(%)

Solar heatgain coeffi cient

KS1000 DL Transparent 38 4.7 1.20 - 6.00 1.3 55 0.58

KS1000 DL Opal White 38 4.7 1.20 - 6.00 1.3 50 0.55

KS1000 DL Blue 38 4.7 1.20 - 6.00 1.3 18 0.48

KS1000 DL Green 38 4.7 1.20 - 6.00 1.3 43 0.51

KS1000 DL Violet 38 4.7 1.20 - 6.00 1.3 13 0.48

KS1000 DL Red 38 4.7 1.20 - 6.00 1.3 25 0.52

KS1000 DL Orange 38 4.7 1.20 - 6.00 1.3 33 0.50

KS1000 DL Yellow 38 4.7 1.20 - 6.00 1.3 55 0.56

KS1000 DL IR Green 38 4.7 1.20 - 6.00 1.3 35 0.40

KS1000 DL IR Blue 38 4.7 1.20 - 6.00 1.3 19 0.36

Notes:The U-value was calculated using the method prescribed by national building guidelines.Light transmission in accordance with BS EN 410 is measured with samples 600 mm x 600 mm in size.The Solar Heat Gain Coeffi cient (SHGC) in accordance with BS EN 410 is the total solar energy thatreaches the interior of a building.Minimum purchase quantities for colour solutions. Please contact our sales employees in this regard.For additional information, please contract the Kingspan Technical Department.

* Longer lengths are available on request.

Note: Condensation can occur in the panel, this does not constitute a defect.

10

Kingspan Day-Lite window element

In practice, windows for lightweight construction are often considered to be touchy problem zones. In particular, each of the thermal advantages of sandwich construction are significantly impaired through conventional installation technologies and often must be compensated with expensive structural measures.

The Kingspan Day-Lite offers essential advantages. The system was developed specifically for the requirements of lightweight projects and meets all the required technical, economic, as well as aesthetic prerequisitesthat the customer expects from this construction method.

3 Significant cost savings. With the Kingspan window element a sheet metal surround on sandwich elements is unnecessary, and retroactive surrounds of the windows – inside and outside – are also unnecessary.

3 Retroactive installation is possible at any time.

3 Visually appealing. Thanks to the especially developed construction principle, visually disturbing screws or rivets are completely dispensed with. A design advantage, particularly for sandwich panels with concealed fastening.

3 Clean closures without sealing compounds.

3 Individual colouring. The Kingspan window element offers a variety of design possibilities; the exterior aluminium frame is available in the RAL and NCS colour spectrum.

3 Outstanding insulation values. Our window surrounds achieve an optimal seal because fasteners do not penetrate the window frame. This design results in a longer service life of the entire window frame construction – also in the corner areas.

3 Also in corner areas.

Investor / planner

11

Versions and application areas

- Available for sandwich element thicknesses 80 – 200 mm

- Retroactive installation is also possible

- In the versions side-hung pane / bottom-hung pane and slanted window, as well as fixed glazing

- Window elements can be provided with textile or slat shading (in accordance with the workplace ordinance)

3 Optimal thermal protection and improved seal

3 Frame construction that is free of thermal bridges.

3 Integrated drainage system dissipates condensation in a controlled manner.

3 Shortened insulation time and material savings.

3 Clamp connection without visible screw fitting

3 Insulated base frame (separate outer and inner shell) is mounted on the panel static and stable via a clamp profile.

3 A sheet metal surround is not necessary.

3 Depending on the structural steelwork requirements, an additional sub-construction can be dispensed with.

Installer / processor

Clear installation advantages

12

10/2017

GermanyKingspan GmbH Am Schornacker 2 46485 WeselT: +49 281 95 25 0-0 F: +49 281 95 25 0-50E: info@kingspan.dewww.kingspan.de

Czech RepublicKingspan a.s.Vážní 465 500 03 Hradec KrálovéT: +420 495 866-111F: +420 495 866-100E: info@kingspan.czhttps://www.kingspan.com

PolandKingspan Sp. z o.o.ul. Przemysłowa 20 27-300, LipskoT: +48 378 31-00 F: +48 378 13-30E: info@kingspan.plhttps://www.kingspan.com

HungaryKingspan Kereskedelmi Kft.Horkadűlő 1 2367 ÚjhartyánT: +36 29 573-400F: +36 29 573-410E: ajanlat@kingspan.huhttps://www.kingspan.com

For the product offering in other areas please contact your local sales representative or visit www.kingspan.de.