Effect of Shear and Axial Effects on Bending Deformation
Transcript of Effect of Shear and Axial Effects on Bending Deformation
![Page 1: Effect of Shear and Axial Effects on Bending Deformation](https://reader034.fdocuments.us/reader034/viewer/2022042320/625cf2bc98397f5bed510140/html5/thumbnails/1.jpg)
Effect of Shear and Axial Effects on Bending Deformation
Steven VukazichSan Jose State University
![Page 2: Effect of Shear and Axial Effects on Bending Deformation](https://reader034.fdocuments.us/reader034/viewer/2022042320/625cf2bc98397f5bed510140/html5/thumbnails/2.jpg)
Lab 12 Exercise
The statically indeterminate steel moment frame on Line B of our CE 160 Lab Building is subjected to the seismic load found in Lab #10. This frame was analyzed in found to have the support reactions, moment, shear, and axial force diagrams shown below.Using the moment (MP), shear (VP), and axial force (FP) diagrams found in Lab #10; find the horizontal displacement, in inches, at the point where the load P is applied using the principle of virtual work.
20 ft
22 ft
P
"2
"2
1011"
1011"
P&W18x65
W14x82
W14x82
![Page 3: Effect of Shear and Axial Effects on Bending Deformation](https://reader034.fdocuments.us/reader034/viewer/2022042320/625cf2bc98397f5bed510140/html5/thumbnails/3.jpg)
Real Moment Diagram (Mp )
10%
10%
0 0
Moment Diagramson the Compression Side
![Page 4: Effect of Shear and Axial Effects on Bending Deformation](https://reader034.fdocuments.us/reader034/viewer/2022042320/625cf2bc98397f5bed510140/html5/thumbnails/4.jpg)
Real Shear Diagram (Vp )
+
+Positive Shear
$2
$2
−1011$
![Page 5: Effect of Shear and Axial Effects on Bending Deformation](https://reader034.fdocuments.us/reader034/viewer/2022042320/625cf2bc98397f5bed510140/html5/thumbnails/5.jpg)
Real Axial Force Diagram (Fp )
Tension Positive
−$2
−1011$1011$
![Page 6: Effect of Shear and Axial Effects on Bending Deformation](https://reader034.fdocuments.us/reader034/viewer/2022042320/625cf2bc98397f5bed510140/html5/thumbnails/6.jpg)
Need to find MQ , VQ , and FQ diagrams (use consistent sign convention)
Virtual System to Measure Horizontal Displacement at Point of Load Application
20 ft
22 ft
1
12
12
1110
1110
![Page 7: Effect of Shear and Axial Effects on Bending Deformation](https://reader034.fdocuments.us/reader034/viewer/2022042320/625cf2bc98397f5bed510140/html5/thumbnails/7.jpg)
Bending Shear Axial force
The effect of bending, shear, and axial force internal work can be found by evaluating the following expression:
! = 1$% &'
()*)+,- +
1/01
&'
(2*2+,- +
1$034*4+5
![Page 8: Effect of Shear and Axial Effects on Bending Deformation](https://reader034.fdocuments.us/reader034/viewer/2022042320/625cf2bc98397f5bed510140/html5/thumbnails/8.jpg)
The appropriate section properties (I, A, As) for each steel W section can be found in the tables of section properties in the AISC Manual of Steel Construction.
Note that the shear area for a W section is the web area:
Cross Sectional Properties of Beam and Columns
!" = $%&
%&$
![Page 9: Effect of Shear and Axial Effects on Bending Deformation](https://reader034.fdocuments.us/reader034/viewer/2022042320/625cf2bc98397f5bed510140/html5/thumbnails/9.jpg)
Cross Section Properties for W18x65 Beam From the AISC Steel Manual
![Page 10: Effect of Shear and Axial Effects on Bending Deformation](https://reader034.fdocuments.us/reader034/viewer/2022042320/625cf2bc98397f5bed510140/html5/thumbnails/10.jpg)
Cross Section Properties for W14x82 ColumnsFrom the AISC Steel Manual
![Page 11: Effect of Shear and Axial Effects on Bending Deformation](https://reader034.fdocuments.us/reader034/viewer/2022042320/625cf2bc98397f5bed510140/html5/thumbnails/11.jpg)
The material properties, E and G, are related to Poisson’s ratio and can be found from:
E = 29,000 ksi for steel
ν = 0.3 (Poisson’s ratio for steel)
Material Properties of Beam and Columns
! = #2 1 + ' = 29,000
2 1 + 0.3 = 11,153.846 ksi
![Page 12: Effect of Shear and Axial Effects on Bending Deformation](https://reader034.fdocuments.us/reader034/viewer/2022042320/625cf2bc98397f5bed510140/html5/thumbnails/12.jpg)
Use Statics to find Moment and Shearfunctions and evaluate product integrals(Recall Lab 10 exercise)
Evaluate Internal Work terms for Bending, Shear, and Axial Force
! = 1$% &'
()*)+,- +
1/01
&'
(2*2+,- +
1$034*4+5
![Page 13: Effect of Shear and Axial Effects on Bending Deformation](https://reader034.fdocuments.us/reader034/viewer/2022042320/625cf2bc98397f5bed510140/html5/thumbnails/13.jpg)
Sign Convention and Coordinates
Sign convention and coordinates to use for functions
20 ft
22 ft
P
"2
"2
+
+
+
+
Shear
Moment
Axial
Tension is positive
yL yR
x
1011"
1011"
![Page 14: Effect of Shear and Axial Effects on Bending Deformation](https://reader034.fdocuments.us/reader034/viewer/2022042320/625cf2bc98397f5bed510140/html5/thumbnails/14.jpg)
SAP 2000 Output Showing Joint Displacement