EDGE Tech - usshoptools.com€¢ Low profile design stays below the top surface of vise jaws for...
2
U S Shop Tools U S Shop Tools CALIFORNIA • MICHIGAN Sales: • Fax: 800-243-7701 800-342-3311 www.usshoptools.com • [email protected] MACHINE SHOP TOOLS & METALWORKING SUPPLIES • Low profile design stays below the top surface of vise jaws for cutter clearance • Versatile design allows the 1/4" hardened stop rod to be quickly and accurately positioned • Stop rod stays parallel to milling machine table so workpiece will contact rod face squarely for increased accuracy • Lever arm can be rotated out of the way for cutter clearance and accurately relocated for repeat setup • Two sets of mounting holes for added versatility • Mounting hardware included • Locate long stock with the included stop rod collar • Large 1/2"-13" bolt used to rigidly attach lever arm • Utilizes non-marring 1/4"-20 set screws • Body made from red anodized 6061-T6 aluminum INCREASE MILLING PRODUCTIVITY! PRO VISE STOPS Single Side Part # EDGE-03000 Mfg’s List: $59.99 $49.99 ea Double Side Part # EDGE-18000 Mfg’s List: $89.99 $74.99 ea NEW ITEM! PRO MILL STOPS The Pro Mill Stop can be mounted on any available T-slot anywhere along the milling machine table allowing it to accurately locate a workpiece for any type of setup. It is designed to keep the stop rod square to the work piece throughout the entire range of motion. This configuration provides a more consistent locating surface for increase part accuracy. The base of the unit is also keyed to the T-slot of table for increased consistency. After locating the workpiece the arm of the Pro Mill Stop can be rotated out of the way for total cutter clearance. The arm can then be accurately repositioned for repeat setup. Mill Stop-5/8” Slot Part # EDGE-16000 Mfg’s List: $59.99 $49.99 ea • 1/4" hardened stop rod • 5/8" T-slot • Stop rod stays parallel to milling machine for increased accuracy • Lever arm can be rotated out of the way for cutter clearance • Base of unit is keyed to T-slot in table • 1/2"-13 bolt attached lever arm to base • T-nut included NEW ITEM! Pro Touch Off Gage Part # EDGE-04000 Mfg’s List: $124.99 $99.99 ea PRO TOUCH OFF GAGE Set tools accurately with the Pro Touch Off Gage. Decrease set up time and eliminate tool path mismatch. Allows you to standardize the way tool offsets are measured in your shop, ensuring every job is setup the same way and runs without issue. To use, simply lower the tool down onto the contact face until the indicator reads zero. You can be confident that the tool tip is exactly 4 inches from the surface the gage is sitting on. • Large 1” dia stainless steel contact face, lightly spring loaded to protect against overrun • Offset height 4.000” (101.6mm) • Large 2.2" easy to read indicator face • Gage graduations 0.001" • Gage repeatability 0.0002" • Body made from red anodized 6061-T6 aluminum • Easy calibration check using 1-2-3 blocks • Padded case and manual included Accurately Establish Tool Length Offsets On CNC Milling Machines! D688 MACHINE VISES $ 529 00 KURT D688 VISE 6” Jaw Width, 8.8” Opening Mfg’s List Price: $587.00 • Large 8.8” jaw opening • AngLock® Vises feature needle- bearing thrust collar • Ground surfaces-vise bed, jaws and all jaw mounting surfaces • Nut does not extend beyond the end of the vise body • Eliminates jaw lift • Powder coat paint • 7968 lbs of max. clamping force! Approximately 20% Increased Clamping Pressure Over Kurt’s D675 Vise! Part # KURT-D688 Vise Jaw Stop Part # EDGE-14000 Mfg’s List: $24.99 $19.99 ea • Stop pin is positioned completely below the top surface of vise jaw to allow for cutter clearance • 1/8" x 2" hardened stop pin, adjustable side-to-side • Fits all milling machine vises with 1/2" - 7/8" thick jaws and 1/8" minimum protrusion • 1-1/8" wide body with 2 hardened steel guide pins • Body made from red anodized aluminum VISE JAW STOP NEW ITEM!
Transcript of EDGE Tech - usshoptools.com€¢ Low profile design stays below the top surface of vise jaws for...
U S Shop Tools
U S Shop ToolsCALIFORNIA • MICHIGAN
Sales: • Fax: 800-243-7701 800-342-3311
www.usshoptools.com • [email protected] SHOP TOOLS & METALWORKING SUPPLIES
• Low profile design stays below the top surface of vise jaws for cutter clearance• Versatile design allows the 1/4" hardened stop rod to be quickly and accurately positioned• Stop rod stays parallel to milling machine table so workpiece will contact rod face squarely for increased accuracy• Lever arm can be rotated out of the way for cutter clearance and accurately relocated for repeat setup• Two sets of mounting holes for added versatility• Mounting hardware included• Locate long stock with the included stop rod collar• Large 1/2"-13" bolt used to rigidly attach lever arm• Utilizes non-marring 1/4"-20 set screws • Body made from red anodized 6061-T6 aluminum
INCREASE MILLING PRODUCTIVITY!
PRO VISE STOPS
Single SidePart # EDGE-03000Mfg’s List: $59.99
$49.99 ea
Double SidePart # EDGE-18000Mfg’s List: $89.99
$74.99 ea
NEW ITEM!
PRO MILL STOPS
The Pro Mill Stop can be mounted on any available T-slot anywhere along the milling machine table allowing it to accurately locate a workpiece for any type of setup. It is designed to keep the stop rod square to the work piece throughout the entire range of motion. This configuration provides a more consistent locating surface for increase part accuracy. The base of the unit is also keyed to the T-slot of table for increased consistency. After locating the workpiece the arm of the Pro Mill Stop can be rotated out of the way for total cutter clearance. The arm can then be accurately repositioned for repeat setup.
Mill Stop-5/8” SlotPart # EDGE-16000Mfg’s List: $59.99
$49.99 ea
• 1/4" hardened stop rod• 5/8" T-slot• Stop rod stays parallel to milling machine for increased accuracy• Lever arm can be rotated out of the way for cutter clearance • Base of unit is keyed to T-slot in table• 1/2"-13 bolt attached lever arm to base• T-nut included
NEW ITEM!
Pro Touch Off GagePart # EDGE-04000Mfg’s List: $124.99
$99.99 ea
PRO TOUCH OFF GAGE
Set tools accurately with the Pro Touch Off Gage. Decrease set up time and eliminate tool path mismatch. Allows you to standardize the way tool offsets are measured in your shop, ensuring every job is setup the same way and runs without issue. To use, simply lower the tool down onto the contact face until the indicator reads zero. You can be confident that the tool tip is exactly 4 inches from the surface the gage is sitting on.
• Large 1” dia stainless steel contact face, lightly spring loaded to protect against overrun• Offset height 4.000” (101.6mm)• Large 2.2" easy to read indicator face• Gage graduations 0.001"• Gage repeatability 0.0002"• Body made from red anodized 6061-T6 aluminum• Easy calibration check using 1-2-3 blocks• Padded case and manual included
Accurately Establish Tool Length Offsets On CNC Milling Machines!
D688 MACHINE VISES
$52900
KURT D688 VISE6” Jaw Width, 8.8” Opening
Mfg’s List Price: $587.00
• Large 8.8” jaw opening• AngLock® Vises feature needle- bearing thrust collar• Ground surfaces-vise bed, jaws and all jaw mounting surfaces• Nut does not extend beyond the end of the vise body• Eliminates jaw lift• Powder coat paint • 7968 lbs of max. clamping force!
Approximately 20% Increased Clamping Pressure Over
Kurt’s D675 Vise!Part # KURT-D688
Vise Jaw StopPart # EDGE-14000Mfg’s List: $24.99
$19.99 ea
• Stop pin is positioned completely below the top surface of vise jaw to allow for cutter clearance• 1/8" x 2" hardened stop pin, adjustable side-to-side • Fits all milling machine vises with 1/2" - 7/8" thick jaws and 1/8" minimum protrusion• 1-1/8" wide body with 2 hardened steel guide pins • Body made from red anodized aluminum
VISE JAW STOP
NEW ITEM!
U S Shop Tools
U S Shop ToolsCALIFORNIA • MICHIGAN
Sales: • Fax: 800-243-7701 800-342-3311
www.usshoptools.com • [email protected] SHOP TOOLS & METALWORKING SUPPLIES
Mill Organizer TrayPart # EDGE-29000
Mfg’s List: $24.99
$19.99 ea
MILL ORGANIZER TRAY
• Designed to fit standard 6" calipers• Multiple compartments segregate endmills and prevent tool damage • Mounts w/ T-slot on table front (included)• Compatible with Bridgeport brand power feed connecting rod• Mill Caddy can be mounted below to improve organization even further• Made from durable fiberglass reinforced composite
NEW ITEM!
GET ORGANIZED!
Vise Jaw LocatorPart # EDGE-47000
Mfg’s List: $49.99
$24.99 ea
VISE JAW LOCATOR• Two powerful magnets hold the unit in place• Adjustable 1/4" stop rod allows compatibility with different width soft jaws• Fits all milling machine vises widths• Rotate stop rod holder arm for use with double side vises• High strength aluminum body• Durable red anodized finish
Accurately Align Soft Jaws
• Fits 6” industry standard vises• Made from 6061 T6 aluminum• Hole space: 3.875”• Hole center height: 0.937• Screw size: 1/2”• 10 pairs per pack• Made in the USA!
10 PACK!FREE SHIPPING!MACHINABLE VISE JAWS
MADE IN USA
*FREE Fedex Ground shipping on 10 pack vise jaws. Must be purchased as package of 10.
NEW ITEM!
Length Height WidthVise Jaw
Finish
10 Pack
Part Number
Reg.
Price
PROMO
PRICE!
3/4" Tumbled VJ-601-10 143.50$ 101.95$
3/4" Machined VJ-6A060207M-10 157.80$ 107.95$
1" Tumbled VJ-602-10 159.30$ 119.95$
1" Machined VJ-6A060201M-10 175.30$ 126.95$
1-1/4" Tumbled VJ-603-10 188.50$ 146.95$
1-1/4" Machined VJ-6A060212M-10 207.30$ 154.95$
2"6"
• Quickly square the head of a milling machine • Perfectly to fit the bed of a 6" vise • Indicator graduations 0.001" and 0.0005"• Shank sizes available in 1/2" and 3/8”• Large 2.2” easy to read indicator face• Indicator repeatability of 0.0002”• Body made from red anodized aluminum• Includes calibration gage, manual and case
PRO TRAM SYSTEMThe Pro Tram by Edge Technology makes the process of tramming your mill fast, easy and accurate. Tramming is the process of squaring the head of your milling machine to the table. The Pro Tram is sized to fit the bed of a 6" vise allowing you to tram directly to vise for increased accuracy. It can be used with a sine bar or sine plate to adjust the head to precise angles.
Ind. Grad0.001”0.001”
0.0005”
Shank Dia1/2”3/8”1/2”
Part #EDGE-01000EDGE-10000EDGE-09000
Mfg’s List$124.99$124.99$139.99
SALE$99.99$99.99$114.99
NEW ITEM!
TAILSTOCK ALIGNMENT BARThe Tailstock Alignment Bar is used to align the tailstock to the headstock. Accurate alignment is critical to eliminate any taper in work pieces that are supported by the tail stock. It makes the process of tailstock alignment fast, easy and accurate.
Tailstock AlignmentBar
Part # EDGE-27000
Mfg’s List: $69.99
$49.99 ea
• Hardened steel bar ends are precision ground after assembly for superior accuracy• Bar end diameters are equal within 0.0001”• Bar made from high strength aluminum• Durable anodized finish
NEW ITEM!
CNC LATHE GAGEThe CNC Lathe Gage is used to set lathe tools on the spindle axis for optimum cutting conditions. Poorly set cutting tools will leave a "NUB" at the center of the workpiece after performing a facing cut. It can be used to set tools on the spindle axis and eliminate this issue. Designed with a large amount of angular adjustability, allowing it to be used with any slant bed or Swiss style CNC lathe. Two different contact faces allows it to work with both upward and downward facing cutting tools.
EliminateThe “Nub”!
• Set turning, boring, and facing tools on spindle axis for optimum cutting conditions• Eliminate the "nub" left by poorly set tools.• Precision glass vial level with 30'/2mm sensitivity• Angular adjustability of +/- 60°• Ground steel shaft supported by dual ball bearings• Made from high strength aluminum
CNC Lathe GagePart # EDGE-13000
Mfg’s List: $44.99
$34.99 ea
NEW ITEM!
