ECM-590 Self-Contained Hydraulic Crawler Drill

2

Simple Load SensingHydraulic SystemThe combination of reliable hydraulic valvesand the load sensing hydraulic system doesnot require complicated electronic controls.Fuel consumption is reduced.

Feed SystemBelleville washers absorb rebound energy.The fully staked chain is of the highestquality available. Separate fast and slowfeed controls can be adjusted to suit rockconditions and operator preference. Drillingaccessories will last longer.

DrillControlsSimple, full flowhydraulic valveseliminate the

need for pilot controls or electric valves. Allthe hydraulic power that is needed travelsfrom valve to function. This simple designvirtually eliminates trouble-shooting time andcomplicated electrical schematics. Reliabilityand up-time are increased.

Foot Piece/Dust HoodThe bolt-on foot piece and 7 inch (verticaltravel) sliding dust hood can tame theroughest ground. When drilling throughexcessive overburden, optional foot pieceextensions are easily added. The ECM-590can go from one drilling condition to anotherquickly and cost effectively. Set-up time isreduced. Overall drill speed increases.

3

Dust Collector FiltersCartridge type filters are cost effective andeasily replaced, lowering maintenance costs.

TramConsoleA full complementof gauges (24 volt)in US and Metric

are simple and informative. The modulargauge design of the console has waterproofconnectors and controls for long life. Thecontrol panel has stainless steel hinges topermit easy access to the wiring harness,thus improving serviceability. The completegauge cluster can be disconnected andremoved if repairs are required.

Heavy-Duty Cooling SystemHinged design allows for easy cleaning atthe job site. Simply pull pin and swing coolerout to perform maintenance. The 125° F (52° C) ambient rating is easily maintained.

Super 18-Inch (457 mm) Ground ClearanceThe ECM-590 will get around the toughestjob site. Full length rock guards and trammotor covers provide unsurpassedprotection. Superior pioneering ability (35°gradability) and high production make theECM-590 a very versatile drill.

4

ECM-590 AirCompressorThe Ingersoll-Rand250 cfm/140 psi (7m3/min, 9.8kg/cm2) aircompressor provides more than adequate aircirculation for hole cleaning. Hole size rangesfrom 2.5 to 4.5 inches in diameter depending ondrifter selection.

ECM-590DrifterMountingPlateIngersoll-Rand'sunique slab-backdesign allows thefeed chain to beeasily maintained.Wear strips on theguide “work harden”

and eliminate guide wear, reducing overallmaintenance costs.

HydraulicHoseManagementRobust synthetic hoseguides and bulkheadsmanage the hydraulichoses. The hosesused are of thehighest qualityavailable and providelong life. Hose management maintenance andcosts are greatly reduced.

Hole Diameter 2.5-4 in. 64-102 mmWeight 419 lbs 190 kgFrequency 2800 bpm 2800 bpmRotation Speed 0-200 rpm 0-200 rpmHydraulic Pressure 2130 psi 150 kg/cm2

Steel Size T45/T38

Type Cummins 6CT8.3Rated Horse Power 215 hp 159 kwOperating Speed 2350 rpm 2350 rpm

Max. Horizontal Boom Swing 30° right/34.6 left

Max. Vertical Boom Movement 51° up/15o down

Max. Guide Swing 48° right/40° leftMax. Guide Dump 180°Boom Extension 48 in. 1219 mmDrifter Travel 15 ft-4 in. 3099 mmGuide Extension 4 ft 1219 mmOverall Guide Length 23 ft-8 in. 7214 mm

Compressor Type Ingersoll-Rand Rotary ScrewCompressor Volume 250 cfm 7 m3/minCompressor Pressure 140 psig 9.9 kg/cm2

Gradability 35°(70%) 35°(70%)Tram Speed 2 mph 3.3 km/hGrouser Width 12 in. 305 mmSteel length 14 ft starter rod 4.27 mManual Rod Rack (4) 10 or 12 ft (3.05 or 3.66 m)/

38 or 45 mm rodsWeight 23,500 lbs 10,660 kgShipping Width 8 ft 2438 mmShipping Height 9 ft-4 in. 2845 mmOverall Length 19 ft-5 in. 5918 mmGround Clearance 18 in. 457 mmFuel Capacity 100 U.S. gal 378 L

Long GuideReverse Percussion (45 mm)Night LightsDrill Console Noise ShieldFoot Piece ExtensionsWinch Kit

OPTI

ONS

GENE

RAL

SPEC

IFIC

ATIO

NSBO

OM&

GUID

EEN

GINE

DRIF

TER

YH70

ECM-590/YH70 Specifications US Metric

5

ECM-590 LongGuideThe ECM-590 longguide version has 22 ft (6.71 m) of drifter travel. A 24 ft (7.32 m) starterrod can be used with the midpoint centralizer forlong, single-pass applications. A manual rod rackwith (4) 12 ft (3.66 m) rods is included for deeperdrilling depths. A 30 in. (762 mm) boom extensionhelps with positioning on the toughest jobs.

ECM-590HydraulicDrifterIngersoll-Rand'shydraulic drifters aresimple and easy tomaintain. Long intervalsbetween drifter resealand heavy-duty front end

components keep the ECM-590 drill on the job.

Automatic Rod ChangerFive 12 ft (3.66 m)rods in the rodchanger plus a 14 ft(4.27 m) starter rodgives this drill 72 ft(21.9 m) depthcapacity. Quick andeasy rod changesreduce operatorfatigue and increaseyour drillingproductivity.

Hole Diameter 2.5-4.5 in. 64-114mmWeight 462 lbs 210 kgFrequency 2600 bpm 2600 bpmRotation Speed 0-200 rpm 0-200 rpmHydraulic Pressure 2130 psi 150 kg/cm2

Steel Size T51/T45

Type Cummins 6CT8.3Rated Horse Power 215 hp 159 kwOperating Speed 2350 rpm 2350 rpm

Max. HorizontalBoom Swing 30° right/34.6° left

Max. VerticalBoom Movement 51° up/15° down

Max. Guide Swing 48° right/40° leftMax. Guide Dump 180°Boom Extension 30 in. 762 mmDrifter Travel 14 ft 4267 mmGuide Extension 4 ft 1219 mmOverall Guide Length 23 ft-8 in. 7214 mm

Compressor Type Ingersoll-Rand Rotary ScrewCompressor Volume 250 cfm 7m3/minCompressor Pressure 140 psig 9.8 kg/cm2

Gradability 35° (70%) 35°(70%)Tram Speed 2 mph 3.3 km/hGrouser Width 12 in 305 mmSteel length 14 ft starter rod 4.27 mAutomatic Rod Changer (5) 12 ft (3.66 m)/

45 or 51 mm rods plus one starter rodWeight 24,500 lbs 11,150 kgShipping Width 8 ft 2438 mmShipping Height 9 ft-4 in. 2845 mmOverall Length 19 ft-5 in. 5918 mmGround Clearance 18 in. 457 mmFuel Capacity 100 U.S. gal 378 L

Reverse Percussion Night LightsDrill Console Noise ShieldFoot Piece ExtensionsWinch Kit

OPTI

ONS

GENE

RAL

SPEC

IFIC

ATIO

NSBO

OM&

GUID

EEN

GINE

DRIF

TER

YH80

A

ECM-590/YH80A Specifications US Metric

6

ECM-590 Long Guide Option

7

ECM-590 Coverage Pattern (Excluding Long Guide Option)30 inch (762 mm) boom extension48 inch (1219 mm) boom extension

157 in. (3987 mm.)

98 in. (2489 mm.)

91 in. (2311 mm.)

96 in

. (24

38 m

m.)12

0 in

. (30

48 m

m.)

124

in. (

3150

mm

.)

88 in

. (22

35 m

m.)

82 in

. (20

83 m

m.)

200 in. (5080 mm.)160 in. (4064 mm.)

90 in. (2286 mm.)

116 in. (2946 mm.)

76 in. (1930 mm.)

181 in. (4597 mm)

151 in. (3835 mm)

ECM-590 Shipping Dimensions (Excluding Long Guide Option)

Suggested blocking locations for transport.

384 in. (9754 mm.)

95 in.(2413 mm.)

112 in.(2845 mm.)

Form 4049-A Printed in U.S.A.

© 1999 Ingersoll-Rand Company

Nothing contained in this brochure is intended to extend any warranty or representation, expressed or implied, regarding the productsdescribed herein. Any such warranties or other terms and conditions of sale of products shall be in accordance with Ingersoll-Rand’sstandard terms and conditions of sale for such products, which are available upon request.

Rock Drill DivisionIngersoll-Rand CompanyRock Drill Division7500 Shadwell DriveRoanoke, VA 24019