Ec6411 EC II Lab Manual 2013
-
Upload
karthik-singaram -
Category
Documents
-
view
220 -
download
1
Transcript of Ec6411 EC II Lab Manual 2013
-
7/25/2019 Ec6411 EC II Lab Manual 2013
1/89
EC 6411-CIRCUIT AND SIMULATION INTEGRATED LABORATORY
DEPT.OF ECE CHENNAI INSTITUTE OF TECHNOLOGY
1
CHENNAI INSTITUTE OF TECHNOLOGY
DEPARTMENT OF ELECTRONICS COMMUNICATION AND
ENGINEERING
EC6411 CIRCUITS AND SIMULATION
INTEGRATED LABORATORY
-
7/25/2019 Ec6411 EC II Lab Manual 2013
2/89
EC 6411-CIRCUIT AND SIMULATION INTEGRATED LABORATORY
DEPT.OF ECE CHENNAI INSTITUTE OF TECHNOLOGY
2
EC6411 CIRCUITS AND SIMULATION INTEGRATED LABORATORY
CYCLEI
DESIGN AND ANALYSIS OF THE FOLLOWING CIRCUITS
1. Series and Shunt fedback amplifiers-Frequency response, Input and output impedance
Calculation
2. RC Phase shift oscilator and Wien Bridge Oscillator
3. Hartley Oscillator and Colpits Oscillator
4. Single Tuned Amplifier5. RC Integrator and Diferentiator circuits
6. Astable and Monostable multivibrators
7. Clipers and Clampers
8. Fre runing Blocking Oscilators
CYCLE-II
SIMULATION USING SPICE (Using Transistor):
1. Tuned Colector Oscillator
2. Twin -T Oscilator /Wein Bridge Oscillator
3. Double and Stager tuned Amplifiers
4. Bistable Multivibrator
5. Schmit Triger circuit with Predictable hysteresis
6. Monostable multivibrator with emiter timing and base timing
7. Voltage and Curent Time base circuits
-
7/25/2019 Ec6411 EC II Lab Manual 2013
3/89
EC 6411-CIRCUIT AND SIMULATION INTEGRATED LABORATORY
DEPT.OF ECE CHENNAI INSTITUTE OF TECHNOLOGY
3
CIRCUIT DIAGRAM:
1. POSITIVE CLIPPER:
FIG.1.1
MODEL GRAPH:
FIG.1.2
-
7/25/2019 Ec6411 EC II Lab Manual 2013
4/89
EC 6411-CIRCUIT AND SIMULATION INTEGRATED LABORATORY
DEPT.OF ECE CHENNAI INSTITUTE OF TECHNOLOGY
4
1. CLIPPER AND CLAMPER CIRCUITS1.1 AIM:
To construct and design the clipper and clamper circuits using diodes.
1.2 APPARATUS REQUIRED:
S.No APPARATUS RANGE QUANTITY
1 Resistors 1 k 1
2 RPS (0-30)V 1
3 Diode IN4007 1
4 CRO (0-
30)MHz
1
6 Function
generator
(0-
10)MHz
1
7 Capacitor 2.5 uf 2
8 Bread board - 1
1.3. DESIGN:
Given f=1 kHz,
T=t=1/f=1x10-3
sec=RC
Assume, C=1uF
Then, R=1K
-
7/25/2019 Ec6411 EC II Lab Manual 2013
5/89
EC 6411-CIRCUIT AND SIMULATION INTEGRATED LABORATORY
DEPT.OF ECE CHENNAI INSTITUTE OF TECHNOLOGY
5
2. NEGATIVE CLIPPER:
FIG.1.3
MODEL GRAPH:
FIG.1.4
-
7/25/2019 Ec6411 EC II Lab Manual 2013
6/89
EC 6411-CIRCUIT AND SIMULATION INTEGRATED LABORATORY
DEPT.OF ECE CHENNAI INSTITUTE OF TECHNOLOGY
6
1.4 THEORY
CLIPPER:
A Clipper is a circuit that removes either the positive or negative part of a
waveform. For a positive clipper only the negative half cycle will appear as output.
CLAMPER:A Clamper circuit is a circuit that adds a dc voltage to the signal. A positive clamper
shifts the ac reference level upto a dc level.
WORKING:
During the positive half cycle, the diode turns on and looks like a short circuitacross the output terminals. Ideally, the output voltage is zero. But practically, the diode
voltage is 0.7 V while conducting.
On the negative half cycle, the diode is open and hence the negative half cycle
appear across the output.
APPLICATION:
Used for wave shaping
To protect sensitive circuits
1.5 PROCEDURE:
1. Connect as per the circuit diagram.2. Set the signal voltage (say 5V, 1 KHz) using signal generator.
3. Observe the output waveform using CRO.
4. Sketch the output waveform.
.
-
7/25/2019 Ec6411 EC II Lab Manual 2013
7/89
EC 6411-CIRCUIT AND SIMULATION INTEGRATED LABORATORY
DEPT.OF ECE CHENNAI INSTITUTE OF TECHNOLOGY
7
CIRCUIT DIAGRAM:
1. CLAMPER CIRCUIT:
Positive clamper
FIG.1.5
MODEL GRAPH:
FIG.1.6
-
7/25/2019 Ec6411 EC II Lab Manual 2013
8/89
EC 6411-CIRCUIT AND SIMULATION INTEGRATED LABORATORY
DEPT.OF ECE CHENNAI INSTITUTE OF TECHNOLOGY
8
QUESTIONS:
1. What are the other names of clipper circuits?
2. What is combinational clipper?
3. Why clippers are used in TV receivers.
4. Give one application of clamper.
5. What are biased clipper and clamper?
-
7/25/2019 Ec6411 EC II Lab Manual 2013
9/89
EC 6411-CIRCUIT AND SIMULATION INTEGRATED LABORATORY
DEPT.OF ECE CHENNAI INSTITUTE OF TECHNOLOGY
9
CIRCUIT DIAGRAM:2. Negative clamper:
FIG.1.7
MODEL GRAPH
FIG.1.8
-
7/25/2019 Ec6411 EC II Lab Manual 2013
10/89
EC 6411-CIRCUIT AND SIMULATION INTEGRATED LABORATORY
DEPT.OF ECE CHENNAI INSTITUTE OF TECHNOLOGY
10
1.6RESULT:Thus the output waveform for Clipper and clamper was observed
-
7/25/2019 Ec6411 EC II Lab Manual 2013
11/89
EC 6411-CIRCUIT AND SIMULATION INTEGRATED LABORATORY
DEPT.OF ECE CHENNAI INSTITUTE OF TECHNOLOGY
11
CIRCUIT DIAGRAM:
1. INTEGRATOR:
FIG.2.1
MODEL GRAPH:
FIG.2.2
-
7/25/2019 Ec6411 EC II Lab Manual 2013
12/89
EC 6411-CIRCUIT AND SIMULATION INTEGRATED LABORATORY
DEPT.OF ECE CHENNAI INSTITUTE OF TECHNOLOGY
12
2. INTEGRATOR AND DIFFERENTIATOR
2.1 AIM:
To design and construct a differentiator and integrator circuit.
2.2APPARATUS REQUIRED:
2.3 THEORY:
Differentiator:Differentiator is a circuit which differentiates the input signal, it
allows high order frequency and blocks low order frequency. If time constant is
very low it acts as a differentiator. In this circuit input is continuous pulse withhigh and low value.
Integrator:In a low pass filter when the time constant is very large it acts as an
integrator. In this the voltage drop across C will be very small in comparison with
the drop across resistor R. So total input appears across the R.
2.4 PROCEDURE:
1. Connections are given as per the circuit diagram.
2. Set the signal voltage.3. Observe the output waveform.
4. Sketch the output waveform.
S.No. APPARATUS RANGE QUANTITY
1. Function generator (0-30)MHz 1
2. CRO (0-30)MHz 1
3. Capacitor 1f 1
4. Resistor 1K 1
5. Bread board - 1
-
7/25/2019 Ec6411 EC II Lab Manual 2013
13/89
EC 6411-CIRCUIT AND SIMULATION INTEGRATED LABORATORY
DEPT.OF ECE CHENNAI INSTITUTE OF TECHNOLOGY
13
CIRCUIT DIAGRAM:
2. DIFFERENTIATOR:
FIG.2.3
MODEL GRAPH:
FIG.2.4
-
7/25/2019 Ec6411 EC II Lab Manual 2013
14/89
EC 6411-CIRCUIT AND SIMULATION INTEGRATED LABORATORY
DEPT.OF ECE CHENNAI INSTITUTE OF TECHNOLOGY
14
QUESTIONS:
1. What is wave shaping circuit?
2. What are the components used in wave shaping circuits.
3. When HPF acts as a differentiator
4. When LPF acts as an integrator.
5. How triangular waveform is obtained using integrator.
2.5 RESULT:Thus the integrator and differentiator is constructed and output
waveform is observed.
-
7/25/2019 Ec6411 EC II Lab Manual 2013
15/89
EC 6411-CIRCUIT AND SIMULATION INTEGRATED LABORATORY
DEPT.OF ECE CHENNAI INSTITUTE OF TECHNOLOGY
15
CIRCUIT DIAGRAM:
1. Without feed back:
C1
1n
RC 3K
R5
1k
+10V
Rs
1k
VCC
CE
58uf
Vi5V
Q1
Ci
66uf
R1
5K
R2
1.1K
FIG.3.1
TABULATION:
(Without feedback)
FREQUENCY OUTPUT
VO(V)
Vin(V) Gain
20log(Vo/Vin)
dB
TAB.3.1
-
7/25/2019 Ec6411 EC II Lab Manual 2013
16/89
EC 6411-CIRCUIT AND SIMULATION INTEGRATED LABORATORY
DEPT.OF ECE CHENNAI INSTITUTE OF TECHNOLOGY
16
3. VOLTAGE SHUNT FEEDBAK AMPLIFIER
3.1 AIM:To design and study frequency response of voltage shunt feedback amplifier.
3.2 APPARATUS REQUIRED:
S.No APPARATUS RANGE QUANTITY
1 AFO (0-1)MHz 1
2 CRO (0-20)V 1
3 Resistors 3k, 1.1 k,5k
2.5 k,1k,
1
4 Power supply (0-30)V 1
5 Transistors BC 107 1
6 Capacitors 66F, 30F,58 f 1
3.3 Design example:Given specifications:
VCC= 10V, IC=1.2mA, AV= 30, fI= 1 kHz, S=2, hFE= 150, =0.4
The feedback factor, = - 1/RF= +1/0.4=2.5K
(i) To calculate RC:
The voltage gain is given by,
AV= -hfe (RC|| RF) / hieh ie = re
re = 26mV / IE= 26mV / 1.2mA = 21.6
hie = 150 x 21.6 =3.2K
Apply KVL to output loop,VCC= ICRC+ VCE+ IERE----- (1)
Where VE= IERE (IC= IE)
VE= VCC/ 10= 1VTherefore RE= 1/1.2x10-3=0.8K= 1K
VCE= VCC/2= 5V
From equation (1), RC= 3 K
(ii) To calculate R1&R2:S=1+ (RB/RE)
RB= (S-1) RE= R1|| R2=1K
RB= R 1R2/ R1+ R2------- (2)VB= VBE+ VE= 0.7+ 1= 1.7V
VB= VCCR2/ R1+ R2------- (3)
Solving equation (2) & (3),
R1= 5 K & R2= 1.1K
-
7/25/2019 Ec6411 EC II Lab Manual 2013
17/89
EC 6411-CIRCUIT AND SIMULATION INTEGRATED LABORATORY
DEPT.OF ECE CHENNAI INSTITUTE OF TECHNOLOGY
17
WITH FEEDBACK:
FIE.3.2
TABULATION:
(With feedback)
FREQUENCY OUTPUT
VO(V)
Vin(V) Gain
20log(Vo/Vin)
dB
TAB.3.2
-
7/25/2019 Ec6411 EC II Lab Manual 2013
18/89
EC 6411-CIRCUIT AND SIMULATION INTEGRATED LABORATORY
DEPT.OF ECE CHENNAI INSTITUTE OF TECHNOLOGY
18
(iii) To calculate Resistance:
Output resistance is given by,RO= RC|| RFRO= 1.3K
input impedance is given by,Ri= (RB|| RF) || hie = 0.6K
Trans-resistance is given by,
Rm= -hfe (RB|| RF)( RC|| RF) / (RB|| RF)+ hieRm= 0.06K
AC parameter with feedback network:
(i) Input Impedance:
Rif= Ri/D (where D= 1+ Rm)
Therefore D = 25
Rif= 24Input coupling capacitor is given by,
Xci= Rif/ 10= 2.4 (since XCi
-
7/25/2019 Ec6411 EC II Lab Manual 2013
19/89
EC 6411-CIRCUIT AND SIMULATION INTEGRATED LABORATORY
DEPT.OF ECE CHENNAI INSTITUTE OF TECHNOLOGY
19
MODEL GRAPH:
FIG.3.3
-
7/25/2019 Ec6411 EC II Lab Manual 2013
20/89
EC 6411-CIRCUIT AND SIMULATION INTEGRATED LABORATORY
DEPT.OF ECE CHENNAI INSTITUTE OF TECHNOLOGY
20
3.4 THEORY:Negative feedback in general increases the bandwidth of the transfer
function stabilized by the specific type of feedback used in a circuit. In Voltage
shunt feedback amplifier, consider a common emitter stage with a resistance Rconnected from collector to base. This is a case of voltage shunt feedback and
we expect the bandwidth of the Trans resistance to be improved due to the
feedback through R. The voltage source is represented by its Nortons
equivalent current source Is=Vs/Rs.
3.5 PROCEDURE:
1. Connect the circuit as per the circuit diagram.2. Set VCC = 10V; set input voltage using audio frequency oscillator.
3. By varying audio frequency oscillator take down output frequency oscillator
voltage for difference in frequency.4. Calculate the gain in dB
5. Plot gain Vs frequency curve in semi-log sheet.
6. Connect the circuit as per the circuit diagram.
7. Set VCC = 10V; set input voltage using audio frequency oscillator.
8. By varying audio frequency oscillator take down output frequency oscillatorvoltage for difference in frequency.
9. Calculate the gain in dB10. Plot gain Vs frequency curve in semi-log sheet.
11. Compare this response with respect to the amplifier without feedback.
-
7/25/2019 Ec6411 EC II Lab Manual 2013
21/89
EC 6411-CIRCUIT AND SIMULATION INTEGRATED LABORATORY
DEPT.OF ECE CHENNAI INSTITUTE OF TECHNOLOGY
21
QUESTIONS:
1. Compare the bandwidth of feedback amplifier.
2. Give the stability of gain with feedback.
3.
Which sampling and mixing network is used in Voltage shunt feed backamplifier,
4. Calculate the input impedance for with feed back.
5. What type of feedback is used in amplifier?
-
7/25/2019 Ec6411 EC II Lab Manual 2013
22/89
EC 6411-CIRCUIT AND SIMULATION INTEGRATED LABORATORY
DEPT.OF ECE CHENNAI INSTITUTE OF TECHNOLOGY
22
3.6 RESULT:
Thus voltage shunt feedback amplifier is designed and studied itsperformance.
-
7/25/2019 Ec6411 EC II Lab Manual 2013
23/89
EC 6411-CIRCUIT AND SIMULATION INTEGRATED LABORATORY
DEPT.OF ECE CHENNAI INSTITUTE OF TECHNOLOGY
23
CIRCUIT DIAGRAM:1. without feed back:
FIG.4.1
TABULATION :( Without feedback)
Vin = ----- (V)
TAB.4.1
FREQUENCY OUTPUT
VO(V)Gain
20log(Vo/Vin) dB
-
7/25/2019 Ec6411 EC II Lab Manual 2013
24/89
EC 6411-CIRCUIT AND SIMULATION INTEGRATED LABORATORY
DEPT.OF ECE CHENNAI INSTITUTE OF TECHNOLOGY
24
4. CURRENT SERIES FEEDBACK AMPLIFER
4.1 AIM:
To design a negative feedback amplifier, and to draw its frequency response.
4.2 APPARATUS REQUIRED:
S.No APPARATUS RANGE QUANTITY
1 AFO (0-1)MHz 1
2 CRO (0-20)MHz 1
3 Resistors 1.5 K,6K,2K,
14k,2.3K,10K
Each one
4 Power supply (0-30V) 1
5 Transistors BC 107 1
6 Capacitors 28F, 10F,720F 1
4.3 Design examples:VCC= 15V, IC=1mA, AV= 30, fL= 50Hz, S=3, hFE= 100, hie= 1.1K
Gain formula is,
AV= - hFERLeff / hie
Assume, VCE = VCC/ 2 (transistor in active region)
VCE= 15 /2=7.5V
VE= VCC/ 10= 15/10=1.5VEmitter resistance is given by, re =26mV/ IETherefore re=26
hie= hfe rehie =2.6K
(i) To calculate RC:
Applying KVL to output loop,
VCC= ICRC+ VCE+ IERE----- (1)Where RE= VE/ IE (IC= IE)
RE= 1.5 / 1x10-3= 1.5K
From equation (1),RC= 6K
(ii) To calculate RB1&RB2:Since IBis small when compared with IC,
IC~ IEVB= VBE+ VE= 0.7 + 1.5=2.2V
VB= VCC(RB2/ RB1+ RB2) ----- (2)
S=1+ (RB/ RE)
-
7/25/2019 Ec6411 EC II Lab Manual 2013
25/89
EC 6411-CIRCUIT AND SIMULATION INTEGRATED LABORATORY
DEPT.OF ECE CHENNAI INSTITUTE OF TECHNOLOGY
25
WITH FEEDBACK:
Fig.4.2
TABULATION:Vin = ----- (V)
TAB.4.2
RB= 2K
FREQUENCY OUTPUT
VO(V)
Gain
20log(Vo/Vin) dB
-
7/25/2019 Ec6411 EC II Lab Manual 2013
26/89
EC 6411-CIRCUIT AND SIMULATION INTEGRATED LABORATORY
DEPT.OF ECE CHENNAI INSTITUTE OF TECHNOLOGY
26
We know that RB= RB1|| RB2RB= R B1RB2/ RB1+RB2--------- (3)
Solving equation (2) & (3),
Therefore,RB1= 14K
From equation (3), RB2= 2.3K
(iii) To find input coupling capacitor (Ci):XCi= (hie|| RB) / 10
XCi= 113
XCi= 1/ 2f CiCi= 1 / 2f XCiCi = 1/ 2X3.14X 50 X 113=28f
(iv)To find output coupling capacitor (CO):
XCO= (RC|| RL) / 10, (Assume RL= 10K)XCO= 375
XCO= 1/ 2f CO
CO= 1/ 2x 3.14x 50 x 375=8f =10 f
(v) To find Bypass capacitor (CE):(Without feedback)
XCE= {(RB+hie / 1+ hfe) || RE}/ 10
XCE= 4.416CE= 1 / 2f XCE
CE= 720 f
Design with feedback:To design with feedback remove the bypass capacitor (CE).
Assume RE= 10K
4.4 THEORY
Negative feedback in general increases the bandwidth of the transferfunction stabilized by the specific type of feedback used in a circuit. In
Voltage series feedback amplifier, consider a common emitter stage
with a resistance R connected from emitter to ground. This is a case
of voltage series feedback and we expect the bandwidth of the transresistance to be improved due to the feedback through R.The voltage
source is represented by its Nortons equivalent current source
Is=Vs/Rs.
-
7/25/2019 Ec6411 EC II Lab Manual 2013
27/89
EC 6411-CIRCUIT AND SIMULATION INTEGRATED LABORATORY
DEPT.OF ECE CHENNAI INSTITUTE OF TECHNOLOGY
27
MODEL GRAPH:
FIG.4.3
-
7/25/2019 Ec6411 EC II Lab Manual 2013
28/89
EC 6411-CIRCUIT AND SIMULATION INTEGRATED LABORATORY
DEPT.OF ECE CHENNAI INSTITUTE OF TECHNOLOGY
28
4.5 PROCEDURE:1. Connect the circuit as per the circuit diagram.
2. Set VCC = 10V; set input voltage using audio frequency oscillator.3. By varying audio frequency oscillator take down output frequency
oscillator voltage for difference in frequency.
4. Calculate the gain in dB5. Plot gain Vs frequency curve in semi-log sheet.
QUESTIONS:
1. What is feedback?
2. what are the parameters used to design the amplifier.
3. Compare the input impedance for with and without feedback?
4. Compare the theorical and practical bandwidth for with feedback.
5. Calculate the value of output impedance with and without feed back.
-
7/25/2019 Ec6411 EC II Lab Manual 2013
29/89
EC 6411-CIRCUIT AND SIMULATION INTEGRATED LABORATORY
DEPT.OF ECE CHENNAI INSTITUTE OF TECHNOLOGY
29
4.6.RESULT:Thus current series feedback amplifier is designed and studied its
performance.
-
7/25/2019 Ec6411 EC II Lab Manual 2013
30/89
EC 6411-CIRCUIT AND SIMULATION INTEGRATED LABORATORY
DEPT.OF ECE CHENNAI INSTITUTE OF TECHNOLOGY
30
BI-POLAR JUNCTION TRANSISTOR
CIRCUIT DIAGRAM:
FIG.5.1
MODEL GRAPH:
FIG.5.2
Amplitude (V)
Time (sec)
-
7/25/2019 Ec6411 EC II Lab Manual 2013
31/89
EC 6411-CIRCUIT AND SIMULATION INTEGRATED LABORATORY
DEPT.OF ECE CHENNAI INSTITUTE OF TECHNOLOGY
31
. RC PHASE SHIFT OSCILLATOR5.1 AIM:
To design a RC phase shift oscillator and to find the frequency of
oscillation.
5.2 APPARATUS REQUIRED:
S.
No
APPARATUS
REQUIRED
RANGE QUA
NTIT
Y
1 Resistors 7.5k
1.4 k
4.8 k
1.2 k,19K,
6.5K
1
1
11
3
2 Power supply (0-30)V 1
3 Transistor BC107 14 Capacitors 1.3f
,2.1f,1.3f
0.01F
1
1
3
5 CRO (0-30)MHz 1
6 Bread board - 1
5.3 Design Example:
Specifications:
VCC= 12V, ICq =1mA, =100, Vceq = 5V, f=1 KHz, S=10, C=0.01 f,hfe= 330, AV= 29
Design:
(i)To find R:
Assume f=1 KHz, C=0.01f
f=1/2RC 6
R=1/2x3.14 6 x1x103x0.01x10
-6=6.5K
Therefore R=6.5K
(ii)To find RE & RC:
VCE = VCC/2 = 6V
re= 26mV / IE= 26hie= hfere= 330 x 26= 8580
On applying KVL to output loop,
VCC=ICRC + VCE+ IERE ----- (1)
VE = IE RE
-
7/25/2019 Ec6411 EC II Lab Manual 2013
32/89
EC 6411-CIRCUIT AND SIMULATION INTEGRATED LABORATORY
DEPT.OF ECE CHENNAI INSTITUTE OF TECHNOLOGY
32
TABULATION:
TAB.5.1
RE = VE /IE=1.2/ 10-3
=1.2K
From equation (1), 12= 10-3
(RC+ 1200) +6= RC= 4800=4.8K
(iii)To calculate R1& R2:
VBB= VCC R2/ R1+ R2------ (2)
VB= VBE+VE= 0.7+12 =1.9VFrom equation (2), 1.9= 12 R2/ R1+ R2
R2/ R1+ R2= 0.158 -------- (3)
S = 1+ RB / RE= RB= 1.2KRB=R1 || R2
0.15R1= 1.2x10-3
=7.5K
R2=0.158 R1 + 0.158 R2, R2= 1.425K
(iv)To calculate Coupling capacitors:
(i) XCi= {[hie+ (1+hfe) RE] || RB}/ 10 = 0.12K
XCi= 1 / 2f Ci == 1.3f(ii) XCO= RLeff /10 [ AV= - hfeRLeff /hie]
RLeff= 0.74K, XCO=0.075 K
XCO= 1 / 2f CO , CO = 2.1f
(iii) XCE= RE /10 = 1.326 f
XCE = 1 / 2f CE=49.27f(iv) Feed back capacitor, XCF= Rf / 10
Cf = 0.636f = 0.01f
Amplitude
(V)
Time period
(msec)
Frequenc
y (Hz)
-
7/25/2019 Ec6411 EC II Lab Manual 2013
33/89
EC 6411-CIRCUIT AND SIMULATION INTEGRATED LABORATORY
DEPT.OF ECE CHENNAI INSTITUTE OF TECHNOLOGY
33
5.4 THEORY:
The low frequencies RC oscillators are more suitable. Tunedcircuit is not an essential requirement for oscillation. The essential
requirement is that there must be a 180ophase shift around the feedback
network and loop gain should be greater than unity. The 180ophase shift in feedback signal can be achieved by suitable RC network.
5.5PROCEDURE:
1. Connect the circuit as per the circuit diagram.
2. Set VCC = 15V.
3. For the given supply the amplitude and time period is measuredfrom CRO.
4. Frequency of oscillation is calculated by the formula f=1/T
5. Amplitude Vs time graph is drawn.
REVIEW QUESTIONS:
1. What is an oscillator?
2. What is barkhausen criterion for oscillation?
3. Which feedback is used in oscillators?
4. Give the frequency of oscillation for RC-phase shift oscillator?
5. Give the disadvantages of phase shift oscillator.
-
7/25/2019 Ec6411 EC II Lab Manual 2013
34/89
EC 6411-CIRCUIT AND SIMULATION INTEGRATED LABORATORY
DEPT.OF ECE CHENNAI INSTITUTE OF TECHNOLOGY
34
5.6 RESULT:
Thus the RC-phase shift oscillator is designed and constructed forthe given frequency.
Theoretical frequency :Practical frequency :
-
7/25/2019 Ec6411 EC II Lab Manual 2013
35/89
EC 6411-CIRCUIT AND SIMULATION INTEGRATED LABORATORY
DEPT.OF ECE CHENNAI INSTITUTE OF TECHNOLOGY
35
CIRCUIT DIAGRAM:
FIG.6.1
MODEL GRAPH:
Amplitude (V)
Time (msec)
FIG.6.2
-
7/25/2019 Ec6411 EC II Lab Manual 2013
36/89
EC 6411-CIRCUIT AND SIMULATION INTEGRATED LABORATORY
DEPT.OF ECE CHENNAI INSTITUTE OF TECHNOLOGY
36
6. HARTLEY OSCILLATOR
6.1 AIM:
To design and construct a Hartley oscillator at the given operating
frequency
6.2 APPARATUS REQUIRED:
S.No APPARATUS RANGE QUANTITY
1 Resistors 2k
1K
100 k
22k
1
11
1
2 RPS (0-30)V 1
3 Transistor BC107 1
4 Capacitors 3.2nf
0.1F
0.01F
11
2
5 Inductor 10mH 2
6 CRO 30MHz 1
7 Bread board - 1
6.3Design Example:Design of feed back Network:Given L1= L2=10mH, f=20 KHz, VCC=12V, IC=3mA, S=12
f = 1/2 CLL )21(
C= 3.2nf
Amplifier design:
(i)Selection of RC:Gain formula is,
AV= - hfeRLeff/ hieAssume VCE=VCC/2 (Transistor active)
VCE= 12/2= 6VVE=IERE= VCC/10=1.2V
VCC=ICRC + VCE+ IERERC= (VCC- VCE-IERE) / IC
Therefore RC = 1.6K=2 K
-
7/25/2019 Ec6411 EC II Lab Manual 2013
37/89
EC 6411-CIRCUIT AND SIMULATION INTEGRATED LABORATORY
DEPT.OF ECE CHENNAI INSTITUTE OF TECHNOLOGY
37
TABULATION:
Amplitude(V) Time(msec) Frequency(Hz)
TAB.6.1
(ii)Selection of RE:IC= IE=3mA
RE= VE/IERE= 1.2 / 3x10-3
=400 =1K
(iii)Selection of R1& R2:Stability factor S=12S=1+ (RB/ RE)
12=1+ (RB/1x103)
RB=11KUsing potential divider rule,
RB=R1R2 / R1+R2& VB= (R2/ R1+R2) VCC
RB/R1= R2/ R1+R2
Therefore RB/R1= VB/VCC
VB=VBE+ VE= 0.7+1.2=1.9V=2VR1= (VCC/ VB )RB
R1= (12/2)x 11x103=66K=100K
VB/VCC =R2 / R1+R22/ 12=R2/ 100x10
3+R2
(100x103)+R2=R2/0.16=19K
R2=19K=22 K
-
7/25/2019 Ec6411 EC II Lab Manual 2013
38/89
EC 6411-CIRCUIT AND SIMULATION INTEGRATED LABORATORY
DEPT.OF ECE CHENNAI INSTITUTE OF TECHNOLOGY
38
(iv)Output capacitance (CO):XCO=RC/10=2x10
3/10=200
1/2fCO=200CO=1/2x3.14x20x10
3x200
CO=0.039=0.01f
(v)Input capacitance (Ci):
XCin= RB/10=11x103/10=1.1x103
1/2fCin=1.1x103
Cin=1/2x3.14x20x103x1.1x10
3
Cin= 0.007=0.01f
(vi) By pass Capacitance (CE):
XCE=RE/10=1x103/10=100
1/2fCE=100CE= 1/2x3.14x20x10
3x100
CE = 0.079f = 0.1f6.4 THEORY:
Hartley oscillator is very popular and is commonly used as
local oscillator in radio receivers. The collector voltage is applied tothe collector through inductor L whose reactance is high compared
with X2and may therefore be omitted from equivalent circuit, at zero
frequency, however capacitor Cbacts as an open circuit.
QUESTIONS:1. How does an oscillator differ from an amplifier?
2. What is the approximate value of hfe in a Hartley oscillator using BJT?
3. Mention the expression for frequency of oscillation?
-
7/25/2019 Ec6411 EC II Lab Manual 2013
39/89
EC 6411-CIRCUIT AND SIMULATION INTEGRATED LABORATORY
DEPT.OF ECE CHENNAI INSTITUTE OF TECHNOLOGY
39
4. Mention the reasons why LC oscillator is preferred over RC oscillator at
radio frequency?
5. How the Hartley oscillator satisfy the barkhausen criterion
6.5 PROCEDURE:
1. Connect the circuit as per the circuit diagram.2. Set VCC = 12V.
3. For the given supply the amplitude and time period is measuredfrom CRO.
4. Frequency of oscillation is calculated by the formula f=1/T
5. Verify it with theoretical frequency, f= 1/2( CLL )21( )
6. Amplitude Vs time graph is drawn.
6.6 RESULT:
Thus the Hartley oscillator is designed and constructed for thegiven frequency.
Theoretical frequency :Practical frequency :
-
7/25/2019 Ec6411 EC II Lab Manual 2013
40/89
EC 6411-CIRCUIT AND SIMULATION INTEGRATED LABORATORY
DEPT.OF ECE CHENNAI INSTITUTE OF TECHNOLOGY
40
CIRCUIT DIAGRAM:
FIG.7.1
MODEL GRAPH:
Amplitude (V)
Time (msec)
FIG.7.2
-
7/25/2019 Ec6411 EC II Lab Manual 2013
41/89
EC 6411-CIRCUIT AND SIMULATION INTEGRATED LABORATORY
DEPT.OF ECE CHENNAI INSTITUTE OF TECHNOLOGY
41
7. COLPITTS OSCILLTOR7.1 AIM:
To design and construct a Colpitts oscillator at the given operating
frequency.
7.2 APPARATUS REQUIRED:
S.No APPARATUS RANGE QUANTITY
1 Resistors 2k
1K
100 k
22k
1
1
11
2 RPS (0-30)V 1
3 Transistor BC107 14 Capacitors 0.1F
0.01F
1
1
5 Inductor 10mH 1
6 CRO 30MHz 1
7 Bread board - 1
7.3 Design of feed back Network:
Given C1= 0.1 F, L=10mH, f=20 KHz, VCC=12V,IC=3mA, S=12
f = 1/22121
CLCCC , C2= 0.01F
Amplifier design:
(i)Selection of RC:
Gain formula is,
AV= - hfeRLeff/ hieAssume VCE=VCC/2 (Transistor active)
VCE= 12/2= 6V
VE=IERE= VCC/10=1.2V
VCC=ICRC + VCE+ IERERC= (VCC- VCE-IERE) / IC
Therefore RC= 1.6K=2 K
(ii) Selection of RE:
IC= IE=3mA
RE= VE/IE= 1K
-
7/25/2019 Ec6411 EC II Lab Manual 2013
42/89
EC 6411-CIRCUIT AND SIMULATION INTEGRATED LABORATORY
DEPT.OF ECE CHENNAI INSTITUTE OF TECHNOLOGY
42
TABULATION:
Amplitude(V) Time( msec ) Frequency(Hz)
TAB.7.1
-
7/25/2019 Ec6411 EC II Lab Manual 2013
43/89
EC 6411-CIRCUIT AND SIMULATION INTEGRATED LABORATORY
DEPT.OF ECE CHENNAI INSTITUTE OF TECHNOLOGY
43
(iii) Selection of R1& R2:Stability factor S=12
S=1+(RB/ RE)
12=1+ (RB/1x103)=11k
Using potential divider rule,
RB=R1R2 / R1+R2& VB= (R2/ R1+R2) VCC
RB/R1= R2/ R1+R2Therefore RB/R1= VB/VCC
VB=VBE+ VE= 0.7+1.2=1.9V=2V
R1= (VCC/ VB ) RB=66K=100K
VB/VCC =R2 / R1+R22/ 12=R2/ 100x10
3+R2
R2=19K=22 K
(iv) Output capacitance (CO):XCO=RC/10=2x10
3/10=200
1/2fCO=200CO=1/2x3.14x20x103x200=0.039=0.01f
(v) Input capacitance (Ci):
XCin= RB/10=11x103/10=1.1x10
3
1/2fCin=1.1x103
Cin=1/2x3.14x20x103x1.1x10
3=0.0101f
(vi) By pass Capacitance (CE):XCE=RE/10=1x10
3/10=100
1/2fCE=100
CE= 1/2x3.14x20x10
3
x100=0.079f = 0.1f
7.4 THEORY:
Colpittsoscillator is very popular and is commonly used as
local oscillator in radio receivers. The collector voltage is applied to thecollector through inductor L whose reactance is high compared with X2
and may therefore be omitted from equivalent circuit, at zero frequency;
The circuit operates as Class C. the tuned circuit determines basically the
frequency of oscillation.
-
7/25/2019 Ec6411 EC II Lab Manual 2013
44/89
EC 6411-CIRCUIT AND SIMULATION INTEGRATED LABORATORY
DEPT.OF ECE CHENNAI INSTITUTE OF TECHNOLOGY
44
QUESTIONS:
1. What is the approximate value of hfein a colpitts oscillator using BJT for
sustained oscillation?
2. What is Tank circuit?
3. Mention the expression for frequency of oscillation?
4. What are the essential parts of an oscillator?
5. Name two high frequency oscillators?
-
7/25/2019 Ec6411 EC II Lab Manual 2013
45/89
EC 6411-CIRCUIT AND SIMULATION INTEGRATED LABORATORY
DEPT.OF ECE CHENNAI INSTITUTE OF TECHNOLOGY
45
7.5PROCEDURE:
1. Connect the circuit as per the circuit diagram.2. Set VCC = 12V.
3. For the given supply the amplitude and time period is measured
from CRO.4. Frequency of oscillation is calculated by the formula f=1/T
5 .Amplitude Vs time graph is drawn.
7.6 RESULT:Thus the colpittsoscillator is designed and constructed for
the given frequency.
Theoretical frequency :Practical frequency :
-
7/25/2019 Ec6411 EC II Lab Manual 2013
46/89
EC 6411-CIRCUIT AND SIMULATION INTEGRATED LABORATORY
DEPT.OF ECE CHENNAI INSTITUTE OF TECHNOLOGY
46
CIRCUIT DIAGRAM:
FIG.8.1
TABULATION:
TAB.8.1
Amplitude(V) Time
period(msec)
-
7/25/2019 Ec6411 EC II Lab Manual 2013
47/89
EC 6411-CIRCUIT AND SIMULATION INTEGRATED LABORATORY
DEPT.OF ECE CHENNAI INSTITUTE OF TECHNOLOGY
47
8. EMITTER COUPLED ASTABLE MULTIVIBRATOR
8.1 AIM:
To design an Emitter coupled Astable multivibrator and study theoutput waveform.
8.2 APPARATUS REQUIRED:
S.No APPARATUS RANGE QUANTITY
1 Resistors 4.7k
470k
2
2
2 RPS (0-30)V 1
3 Transistor BC107 2
4 Capacitors 0.01F 2
5 CRO (0-30)MHz 1
6 Bread board - 1
8.3 Design example:
Given specifications:
VCC= 10V; hfe = 100; f=1 KHz; I c = 2mA; Vce (sat) = 0.2v;
To design RC:
R hFERCRC= VCC- VC2 (Sat)/ IC= 4.9 k
Since R hFERC
Therefore R100 x 4.7 x103=490 k 470 kTo Design C:
Since T= 1.38RC1x10
-3=1.38x 490x10
3x C
Therefore C=0.01F
-
7/25/2019 Ec6411 EC II Lab Manual 2013
48/89
EC 6411-CIRCUIT AND SIMULATION INTEGRATED LABORATORY
DEPT.OF ECE CHENNAI INSTITUTE OF TECHNOLOGY
48
MODEL GRAPH:
FIG.8.2
-
7/25/2019 Ec6411 EC II Lab Manual 2013
49/89
EC 6411-CIRCUIT AND SIMULATION INTEGRATED LABORATORY
DEPT.OF ECE CHENNAI INSTITUTE OF TECHNOLOGY
49
8.4. THEORY:
The astable multivibrator generates square wave without any
external triggering pulse. It has no stable state, i.e., it has two quasi-stable states. It switches back and forth from one stable state to other,
remaining in each state for a time depending upon the discharging of a
capacitive circuit.When supply voltage + Vcc is applied, one transistor will
conduct more than the other due to some circuit imbalance.
8.5 PROCEDURE:
1. Connect the circuit as per the circuit diagram.2. Set VCC = 5V.
3. For the given supply the amplitude and time period is measured
from CRO.
4. Frequency of oscillation is calculated by the formula f=1/T5. Amplitude Vs time graph is drawn.
QUESTIONS:
1. What is meant by multivibrator?
2. What is the frequency of oscillation of astable multivibrator?
3. Distinguish oscillator and multivibrator?
-
7/25/2019 Ec6411 EC II Lab Manual 2013
50/89
EC 6411-CIRCUIT AND SIMULATION INTEGRATED LABORATORY
DEPT.OF ECE CHENNAI INSTITUTE OF TECHNOLOGY
50
4. List the applications of astable multivibrator.
5. Why it is called as free running multivibrator.
8.6 RESULT:
Thus the astable multivibrator is designed and output waveform is plotted.
-
7/25/2019 Ec6411 EC II Lab Manual 2013
51/89
EC 6411-CIRCUIT AND SIMULATION INTEGRATED LABORATORY
DEPT.OF ECE CHENNAI INSTITUTE OF TECHNOLOGY
51
CIRCUIT DIAGRAM:
FIG.9.1
TABULATION:
TAB.9.1
Amplitude(V) Time period(msec)
TON TOFF
-
7/25/2019 Ec6411 EC II Lab Manual 2013
52/89
EC 6411-CIRCUIT AND SIMULATION INTEGRATED LABORATORY
DEPT.OF ECE CHENNAI INSTITUTE OF TECHNOLOGY
52
9. MONOSTABLE MULTIVIBRATOR
9.1 AIM:
To design and test the performance of Monostable multivibratorfor the given frequency.
9.2 APPARATUS REQUIRED:
S.No APPARATUS RANGE QUANTITY
1 Resistors 5.9 k
452 k,
100 k
10K
21
1
1
2 RPS (0-30)V 1
3 Transistor BC107 1
4 CRO (0-30)MHz 1
5 Capacitor 3.2nf
25pf
1
1
6 Bread board - 1
9.3 Design Example:
Given specifications:VCC= 12V; hfe = 200; f=1 KHz; I c = 2mA; Vce (sat) = 0.2v; VBB= - 2V,
(i)To calculate RC:
RC =VCC- Vce (sat) / IC
RC= 120.2 / 2x10-3
=5.9K(ii)To calculate R:
IB2(min)=IC2 / hfe= 2x10-3
/ 200 = 10 A
Select IB2> IB1(min) (say 25 A)Then R=VCCV BE(sat) / IB2
Therefore R= 12-0.7/25x10-6
=452K
(iii) To calculate C:
T=0.69RC1x10
-3= 0.69x452x10
3xC
C=3.2nf
-
7/25/2019 Ec6411 EC II Lab Manual 2013
53/89
EC 6411-CIRCUIT AND SIMULATION INTEGRATED LABORATORY
DEPT.OF ECE CHENNAI INSTITUTE OF TECHNOLOGY
53
MODEL GRAPH:
FIG.9.2
-
7/25/2019 Ec6411 EC II Lab Manual 2013
54/89
EC 6411-CIRCUIT AND SIMULATION INTEGRATED LABORATORY
DEPT.OF ECE CHENNAI INSTITUTE OF TECHNOLOGY
54
To calculate R1 & R2:
VB1= {(VBBR1/ R1 +R2) + (VCE (sat)R2 / R1+R2)}Since Q1 is in off state ,VB1 0
Then (VBBR1/ R1 +R2) = (VCE (sat)R2 / R1+R2)
VBBR1 = VCE (sat)R22 R1 = 0.2 R2
Assume R1=10K, then R2=100K
Consider, C1= 25pf (commutative capacitor)
9.4 THEORY:
The monostable multivibrator has one stable state when an
external trigger input is applied the circuit changes its state from stable toquasi stable state. And then automatically after some time interval the
circuit returns back to the original normal stable state. The time T is
dependent on circuit components.
The capacitor C1is a speed-up capacitor coupled to base of Q2through C.Thus DC coupling in bistable multivibrator is replaced by a capacitor
coupling. The resistor R at input of Q2 is returned to VCC.The value of R2 , VBB are chosen such that transistor Q1 is off
by reverse biasing it. Q2 is on. This is possible by forward biasing Q2
with the help of VCC and resistance R. Thus Q2-ON and Q1-OFF is
normal stable state of circuit.
9.5 PROCEDURE:
1. Connect the circuit as per the circuit diagram.
2. Give a negative trigger input to Q2.3. Note the output of transistor Q2 and Q1.4. Find the value of Ton and Toff.
-
7/25/2019 Ec6411 EC II Lab Manual 2013
55/89
EC 6411-CIRCUIT AND SIMULATION INTEGRATED LABORATORY
DEPT.OF ECE CHENNAI INSTITUTE OF TECHNOLOGY
55
QUESTIONS:
1. Give the other names of monostable multivibrator?
2. What is the use of commutating capacitor?
3. What is the frequency of oscillation of monostable multivibrator?
4. Why it is called as one-shot multivibrator?
5. List the applications of mono stable multivibrator.
9.6 RESULT:
Thus the monostable multivibrator is designed and theperformance is tested.
Theoretical period :Practical period :
-
7/25/2019 Ec6411 EC II Lab Manual 2013
56/89
EC 6411-CIRCUIT AND SIMULATION INTEGRATED LABORATORY
DEPT.OF ECE CHENNAI INSTITUTE OF TECHNOLOGY
56
CIRCUIT DIAGRAM:
FIG.10.1
TABULATION:
TAB.10.1
Amplitude(V) Time period(msec)
-
7/25/2019 Ec6411 EC II Lab Manual 2013
57/89
EC 6411-CIRCUIT AND SIMULATION INTEGRATED LABORATORY
DEPT.OF ECE CHENNAI INSTITUTE OF TECHNOLOGY
57
10. BISTABLE MULTIVIBRATOR
10.1 AIM:
To design a bi-stable multivibrator and study the output waveform
10.2 APPARATUS REQUIRED:
S.No APPARATUS RANGE QUANTITY
1 Resistors 5.9 k
100 k
10K
2
21
2 RPS (0-30)V 1
3 Transistor BC107 1
4 CRO (0-30)MHz 1
5 Capacitor 50pf 2
6 Bread board - 1
10.3 Design Example:Given specifications:VCC=12V,VBB = - 12V, IC= 2mA , VC(Sat)= 0.2V, VBE(Sat)= 0.7V, hfe=200
Assume Q1 is cut off, i.e. VC1= VCC (+12V)
Q2 is saturation (ON), i.e.VC2= VC (Sat)(0.2V)Using superposition principle,
VB1 = [VBB( R1/ R1+R2) + VC2(R2 / R1+R2)]
-
7/25/2019 Ec6411 EC II Lab Manual 2013
58/89
EC 6411-CIRCUIT AND SIMULATION INTEGRATED LABORATORY
DEPT.OF ECE CHENNAI INSTITUTE OF TECHNOLOGY
58
MODEL GRAPH:
FIG.10.2
-
7/25/2019 Ec6411 EC II Lab Manual 2013
59/89
EC 6411-CIRCUIT AND SIMULATION INTEGRATED LABORATORY
DEPT.OF ECE CHENNAI INSTITUTE OF TECHNOLOGY
59
To calculate R1 & R2:
Assume, R1 = 10K
By using inequality, R1< hfeRC
R2= 91.67k= 100k [Using equation (1)]Since IB2> IB2(min) , Q2 is ON
Choose Capacitor C1= 25pf (commutative capacitor)
10.5 PROCEDURE:
1. Connect the circuit as per the circuit diagram2. Switch on the regulated power supply and observe the output
waveform at the collector of Q1 and Q2.
3. Sketch the waveform.
4. Apply a threshold voltage of VT (pulse voltage) and observe thechanges of states of Q1 and Q2
5. Sketch the waveform
-
7/25/2019 Ec6411 EC II Lab Manual 2013
60/89
EC 6411-CIRCUIT AND SIMULATION INTEGRATED LABORATORY
DEPT.OF ECE CHENNAI INSTITUTE OF TECHNOLOGY
60
QUESTIONS:
1. Define storage time of bistable multivibrator?
2. What are the different types of triggering of bistable multivibrator?
3. List the application of bistable multivibrator.
4. What is the use of triggering in bistable multivibrators?
5. Give the differences between three multivibrators.
10.6 RESULT:
Thus the bistable multivibrator is designed and the
performance is tested.
-
7/25/2019 Ec6411 EC II Lab Manual 2013
61/89
EC 6411-CIRCUIT AND SIMULATION INTEGRATED LABORATORY
DEPT.OF ECE CHENNAI INSTITUTE OF TECHNOLOGY
61
CIRCUIT DIAGRAM:
FIG11.1
MODEL GRAPH:
FIG.11.2
-
7/25/2019 Ec6411 EC II Lab Manual 2013
62/89
EC 6411-CIRCUIT AND SIMULATION INTEGRATED LABORATORY
DEPT.OF ECE CHENNAI INSTITUTE OF TECHNOLOGY
62
11. SINGLE TUNED AMPLIFIER
11.1 AIM:
To design a single tuned amplifier and to draw its frequency
response.
11.2 APPARATUS REQUIRED:
11.3
DESIGN EXAMPLE:
Given specificationsVcc = 12V, = 100, Ic = 1mA, L=1mH, f=2 KHz, S= [2-10]
Assume, VCE= VCC / 2=6V
VE= VCC / 10 =1.2V
To calculate C:
F = 1/ 2 LC
Therefore C=0 .6f
To calculate RE:VE= IE RE (IC= IE)
RE= VE / IE= 1.2 / 1x10-3
= 1.2KAssume S= 10, S= 1+ (RB/ RE)
Therefore RB= 10K
To find R1& R2:
RB= R1 || R2
RB= R1 R2 / R1+ R2------------- (1)VB= VCC x (R2/ R1+ R2) ------ (2)
S.No
APPARATUS RANGE QUANTITY
1 Resistors 10k
63 k
1.2k
10 k
11
1
2
2 RPS (0-30)V 1
3 Transistor BC107 1
4 Capacitors 0.1f ,0.6f1 f , 0.01 f
Each one
5 CRO (0-30)MHz 1
6 Function generator (0-10)MHz 1
7 Bread board - 1
-
7/25/2019 Ec6411 EC II Lab Manual 2013
63/89
EC 6411-CIRCUIT AND SIMULATION INTEGRATED LABORATORY
DEPT.OF ECE CHENNAI INSTITUTE OF TECHNOLOGY
63
TABULATION:
V in= ------- (V)
TAB.11.1
FREQUENCY OUTPUT
VO(V)
Vin (V) Gain
20log(Vo/Vin) dB
-
7/25/2019 Ec6411 EC II Lab Manual 2013
64/89
EC 6411-CIRCUIT AND SIMULATION INTEGRATED LABORATORY
DEPT.OF ECE CHENNAI INSTITUTE OF TECHNOLOGY
64
From equation 1 & 2
RB / R1 = VB/ VCC --------------- (3)
VB= VBE+ VE (VBE= 0.7)VB= 0.7 + 1.2 = 1.9V
Substitute values in equation 3, R1= 63K
From equation 2 , R2= 11K 10KTo calculate coupling capacitors:
(i)Input capacitance (Ci):
XCi = {[ hie+ (1+ hfe)RE] || RB} /10 (OR) RB /10XCi= 100
XCi= 1/ 2fCiTherefore Ci= 0.7 f 1f
(ii) Output capacitance ( CO):XCO = RC|| RL/ 10 RL / 10
XCO = 1000 [since RL= 10K]
XCO= 1/ 2fCOCO= 0.0796 f 0.1f
(iii) Bypass capacitance (CE):
XCE = RE/ 10XCE= 120
XCE= 1/ 2fCECE = 0.06 f 0.01f
11.4 THEORY:
The single tuned amplifier selecting the range of frequency theresistance load replaced by the tank circuit. Tank circuit
is nothing but inductors and capacitor in parallel with each other.
The tuned amplifier gives the response only at particularfrequency at which the output is almost zero. The resistor R1 and R2
provide potential diving biasing, Re and Ce provide the thermal
stabilization. This it fixes up the operating point.
11.5 PROCEDURE:
1. Connections are given as per the circuit diagram
2. By varying frequency, amplitude is noted down3. Gain is calculated in dB
4. Frequency response curve is drawn.
-
7/25/2019 Ec6411 EC II Lab Manual 2013
65/89
EC 6411-CIRCUIT AND SIMULATION INTEGRATED LABORATORY
DEPT.OF ECE CHENNAI INSTITUTE OF TECHNOLOGY
65
QUESTIONS:
1. Define Q-factor?
2. What is tuned circuit?
3. What is coil loss?
4. Give the application of Single tuned Class-C amplifier
5. What is tank circuit?
11.6 RESULT:
Thus the classc single tuned amplifier is designed andfrequency response is plotted.
-
7/25/2019 Ec6411 EC II Lab Manual 2013
66/89
EC 6411-CIRCUIT AND SIMULATION INTEGRATED LABORATORY
DEPT.OF ECE CHENNAI INSTITUTE OF TECHNOLOGY
66
CIRCUIT DIAGRAM:
FIG.12.1
TABULATION:
TAB.12.1
Amplitude(V) Time(msec)
-
7/25/2019 Ec6411 EC II Lab Manual 2013
67/89
EC 6411-CIRCUIT AND SIMULATION INTEGRATED LABORATORY
DEPT.OF ECE CHENNAI INSTITUTE OF TECHNOLOGY
67
12. WEIN- BRIDGE OSCILLATOR
12.1 AIM:To design a Wein-bridge oscillator using transistors and to find the frequency
of oscillation.
12.2 APPARATUS REQUIRED:
S.No APPARATUS REQUIRED RANGE QUANTITY
1 Resistors 33 k
1.5 k
15 k
11
1
1
2 Power supply 5V 1
3 Opamp IC147 1
4 Capacitors 0.1F 2
5 CRO 1
6 Bread board 1
12.3Design Example:Assume f=1 KHz, C=0.1f
f = 1/ 2RC
R= 1/2fCR =1/2x3.14x1x10
3x0.1x10
3
R= 1.59KTo calculate R1:
R1= 10R
R1=10x1.5K
R1=15.9K
To calculate Rf (Feed back resistor):Rf= 2R1
Rf = 2(15.9x103)=31.8K 33K
-
7/25/2019 Ec6411 EC II Lab Manual 2013
68/89
EC 6411-CIRCUIT AND SIMULATION INTEGRATED LABORATORY
DEPT.OF ECE CHENNAI INSTITUTE OF TECHNOLOGY
68
MODEL GRAPH:
FIG.12.2
12.4 THEORY:
Generally in an oscillator, amplifier stage introduces 180o phase shift and
feedback network introduces additional 180ophase shift, to obtain a phase shift of
360oaround a loop. This is a condition for any oscillator. But Wein bridge oscillator uses
a non-inverting amplifier and hence does not provide any phase shift during amplifier
stage. As total phase shift requires is 0o
or 2n radians, in Wein bridge type no phaseshift is necessary through feedback. Thus the total phase shift around a loop is 0
o.
The output of the amplifier is applied between the terminals 1 and 3, which
are the input to the feedback network. While the amplifier input is supplied from the
diagonal terminals 2 and 4, which is the output from the feedback network. Thus
amplifier supplied its own output through the Wein bridge as a feed back network.The two arms of the bridge, namely R1, C1 in series and R2, C2 in parallel are
called frequency sensitive arms. This is because the components of these two arms
decide the frequency of the oscillator. Advantage of Wein bridge oscillator is that byvarying the two-capacitor values simultaneously, by mounting them on the common
shaft, different frequency ranges can be provided.
12.5 ROCEDURE:
1. Connect the circuit as per the circuit diagram.
2. Set VCC = 5V.3. For the given supply the amplitude and time period is measured from CRO.
4. Frequency of oscillation is calculated by the formula f=1/T5. Amplitude Vs time graph is drawn.
Amplitude (V)
Time (sec)
-
7/25/2019 Ec6411 EC II Lab Manual 2013
69/89
EC 6411-CIRCUIT AND SIMULATION INTEGRATED LABORATORY
DEPT.OF ECE CHENNAI INSTITUTE OF TECHNOLOGY
69
QUESTIONS:
1.
Give the condition for maximum oscillation.
2. What is the frequency of oscillation under balanced condition?
3. In which way high gain is obtained in wein bridge oscillator.
4. How to improve the amplitude stability of output waveform.
5.
What is the frequency of oscillation?
12.6 RESULT:
Thus the Weinbridge oscillator is designed for the given frequency of
oscillation.
Theoretical frequency :Practical frequency :
-
7/25/2019 Ec6411 EC II Lab Manual 2013
70/89
EC 6411-CIRCUIT AND SIMULATION INTEGRATED LABORATORY
DEPT.OF ECE CHENNAI INSTITUTE OF TECHNOLOGY
70
SIMULATION USING PSPICE
-
7/25/2019 Ec6411 EC II Lab Manual 2013
71/89
EC 6411-CIRCUIT AND SIMULATION INTEGRATED LABORATORY
DEPT.OF ECE CHENNAI INSTITUTE OF TECHNOLOGY
71
CIRCUIT DIAGRAM:
FIG.1.1
MODEL GRAPH:
FIG.1.2
-
7/25/2019 Ec6411 EC II Lab Manual 2013
72/89
EC 6411-CIRCUIT AND SIMULATION INTEGRATED LABORATORY
DEPT.OF ECE CHENNAI INSTITUTE OF TECHNOLOGY
72
1. ASTABLE MULTIVIBRATOR
1.1 AIM:
To simulate an astable multivibrator using PSPICE
1.2APPARATUS REQUIRED:
1. PC
2. PSPICE software
1.3 THEORY:
Astable multivibrator has two states and both states are quasi states
without giving any external trigger pulse, so this multivibrator is alsocalled as free running multivibrator, it is used to generate square wave
oscillations. It can be operated as an oscillator over wide range of audioand radio frequencies. Used as voltage frequency converter and in pulse
synchronization as clock for binary logic signal.
1.4 PROCEDURE:
1. Click on the start menu and select the pspice simulation software
2. Select the parts required for the circuit from the parts menu and placethem in the work space
3. Connect the parts using wires4. Save the file and select the appropriate analysis5. Simulate the circuit and observe the corresponding output waveforms
-
7/25/2019 Ec6411 EC II Lab Manual 2013
73/89
EC 6411-CIRCUIT AND SIMULATION INTEGRATED LABORATORY
DEPT.OF ECE CHENNAI INSTITUTE OF TECHNOLOGY
73
QUESTIONS:
1. What is PSpice?
2. What is the use of Pspice?
3. What are the different types of analysis done using Spice?
4. List the limitation of Pspice
5. What are the different output commands?
-
7/25/2019 Ec6411 EC II Lab Manual 2013
74/89
EC 6411-CIRCUIT AND SIMULATION INTEGRATED LABORATORY
DEPT.OF ECE CHENNAI INSTITUTE OF TECHNOLOGY
74
1.5 RESULT:
Thus the astable multivibrator is simulated using PSpice.
-
7/25/2019 Ec6411 EC II Lab Manual 2013
75/89
EC 6411-CIRCUIT AND SIMULATION INTEGRATED LABORATORY
DEPT.OF ECE CHENNAI INSTITUTE OF TECHNOLOGY
75
CIRCUIT DIAGRAM:
FIG.2.1
MODEL GRAPH:
FIG.2.2
-
7/25/2019 Ec6411 EC II Lab Manual 2013
76/89
EC 6411-CIRCUIT AND SIMULATION INTEGRATED LABORATORY
DEPT.OF ECE CHENNAI INSTITUTE OF TECHNOLOGY
76
2. MONO STABLE MULTIVIBRATOR
2.1 AIM:
To simulate an monostable multivibrator using PSPICE
2.2 APPARATUS REQUIRED:
1. PC
2. PSPICE software
2.3 THEORY:
Monostable multivibrator is an electronic circuit which hasone stable state and one quasi stable state. It needs external pulse to
change their stable state to quasi state and return back to its stable stateafter completing the time constant RC. Thus the RC time constant
determines the duration of quasi state. Also called as one-shot, single shotand one swing multivibrator.Used as triggering circuit for some circuits
like timer circuit, delay circuits etc.
2.4 PROCEDURE:
1. Click on the start menu and select the pspice simulation software
2. Select the parts required for the circuit from the parts menu andplace them in the work space
3. Connect the parts using wires4. Save the file and select the appropriate analysis5. Simulate the circuit and observe the corresponding output
waveforms
-
7/25/2019 Ec6411 EC II Lab Manual 2013
77/89
EC 6411-CIRCUIT AND SIMULATION INTEGRATED LABORATORY
DEPT.OF ECE CHENNAI INSTITUTE OF TECHNOLOGY
77
QUESTIONS:
1. Give the other names of monostable multivibrator?
2. What is the use of commutating capacitor?
3. What is the frequency of oscillation of monostable multivibrator?
4. Why it is called as one-shot multivibrator?
5. List the applications of mono stable multivibrator.
2.5 RESULT:
Thus the monostable multivibrator is simulated using PSpice .
-
7/25/2019 Ec6411 EC II Lab Manual 2013
78/89
EC 6411-CIRCUIT AND SIMULATION INTEGRATED LABORATORY
DEPT.OF ECE CHENNAI INSTITUTE OF TECHNOLOGY
78
CIRCUIT DIAGRAM:
FIG.3.1
MODEL GRAPH:
FIG.3.2
-
7/25/2019 Ec6411 EC II Lab Manual 2013
79/89
EC 6411-CIRCUIT AND SIMULATION INTEGRATED LABORATORY
DEPT.OF ECE CHENNAI INSTITUTE OF TECHNOLOGY
79
3. BI-STABLE MULTIVIBRATOR
3.1 AIM:
To simulate an Bi-stable multivibrator using PSPICE
3.2 APPARATUS REQUIRED:
1. PC2. PSPICE software
3.3 THEORY:
Bi- stable multivibrator contains two stable states and no quasistates. It requires two clock or trigger pulses to change the states. It is also
called as flip flop, scale of two toggle circuit, trigger circuit. It is used in digitaloperations like counting, storing datas in flip flops and production of square
waveforms.
\
3.4 PROCEDURE:
1. Click on the start menu and select the pspice simulation software
2. Select the parts required for the circuit from the parts menu and placethem in the work space
3. Connect the parts using wires
4. Save the file and select the appropriate analysis5. Simulate the circuit and observe the corresponding output waveforms
-
7/25/2019 Ec6411 EC II Lab Manual 2013
80/89
EC 6411-CIRCUIT AND SIMULATION INTEGRATED LABORATORY
DEPT.OF ECE CHENNAI INSTITUTE OF TECHNOLOGY
80
QUESTIONS:
1. Define storage time of bistable multivibrator?
2. What are the different types of triggering of bistable
multivibrator?
3. List the application of bistable multivibrator.
4. What is the use of triggering in bistable multivibrators?
5. Give the differences between three multivibrators.
3.5 RESULT:
Thus the Bi-stable multivibrator is simulated using PSpice.
-
7/25/2019 Ec6411 EC II Lab Manual 2013
81/89
EC 6411-CIRCUIT AND SIMULATION INTEGRATED LABORATORY
DEPT.OF ECE CHENNAI INSTITUTE OF TECHNOLOGY
81
CMOS
CIRCUIT DIAGRAM:
FIG.4.1
MODEL GRAPH:
-
7/25/2019 Ec6411 EC II Lab Manual 2013
82/89
EC 6411-CIRCUIT AND SIMULATION INTEGRATED LABORATORY
DEPT.OF ECE CHENNAI INSTITUTE OF TECHNOLOGY
82
FIG.4.2
4. CMOS INVERTER
4.1 AIM:To simulate an CMOS inverter using PSPICE
4.2 APPARATUS REQUIRED:
1. PC
2. PSPICE software
4.3 THEORY: CMOS-Complementary metal oxide semiconductor.it uses
one pmos and nmos connected together in complementaryto theanother.any number of circuits can be designed using CMOS.input is
commonly given to the base and due to the circuit nconnection output
of a CMOS is inverted.
4.4 PROCEDURE:
1. Click on the start menu and select the pspice simulation software
2. Select the parts required for the circuit from the parts menu and
place them in the work space3. Connect the parts using wires
4. Save the file and select the appropriate analysis
5. Simulate the circuit and observe the corresponding output
waveforms
-
7/25/2019 Ec6411 EC II Lab Manual 2013
83/89
EC 6411-CIRCUIT AND SIMULATION INTEGRATED LABORATORY
DEPT.OF ECE CHENNAI INSTITUTE OF TECHNOLOGY
83
QUESTIONS:
1. What is the advantage of CMOS over NMOS and PMOS?
2. What are different types of CMOS inverter?
3.
What is the current CMOS technology?
4. List the CMOS parameters.
5. Give the applications of CMOS.
4.5 RESULT:
Thus the CMOS inverter is simulated using PSpice.
-
7/25/2019 Ec6411 EC II Lab Manual 2013
84/89
EC 6411-CIRCUIT AND SIMULATION INTEGRATED LABORATORY
DEPT.OF ECE CHENNAI INSTITUTE OF TECHNOLOGY
84
CIRCUIT DIAGRAM:
FIG.5.1
MODEL GRAPH:
FIG.5.2
-
7/25/2019 Ec6411 EC II Lab Manual 2013
85/89
EC 6411-CIRCUIT AND SIMULATION INTEGRATED LABORATORY
DEPT.OF ECE CHENNAI INSTITUTE OF TECHNOLOGY
85
5. ANALOG MULTIPLIER
5.1 AIM:
To simulate an Analog multivibrator using PSPICE
5.2 APPARATUS REQUIRED:
1. PC
2. PSPICE software
5.3 THEORY:
Anolog multiplier is used to multiply two input singal.if a
input is given to a log amplifier an dthe output can be taken in the
antilog amplifier.it is the simple way to test the multiplied signal.in thiscircuit it is designed using Ic.input is given to the terminals of two Ics
and output is taken across . It is similar to log and antilog operation.
5.4 PROCEDURE:
1. Click on the start menu and select the p spice simulation software2. Select the parts required for the circuit from the parts menu and
place them in the work space
3. Connect the parts using wires
4. Save the file and select the appropriate analysis5. Simulate the circuit and observe the corresponding output
waveforms
-
7/25/2019 Ec6411 EC II Lab Manual 2013
86/89
EC 6411-CIRCUIT AND SIMULATION INTEGRATED LABORATORY
DEPT.OF ECE CHENNAI INSTITUTE OF TECHNOLOGY
86
QUESTIONS:
1. Draw the analog multiplier circuit using log and antilog.
2. Give the effect of output using log and antilog amplifiers.
3. Give the applications of analog multiplier.
4. Give the advantage of analog multiplier.
5. What are the circuits used to multiply two inputs.
5.5 RESULT:
Thus the analog multivibrator is simulated using PSpice.
-
7/25/2019 Ec6411 EC II Lab Manual 2013
87/89
EC 6411-CIRCUIT AND SIMULATION INTEGRATED LABORATORY
DEPT.OF ECE CHENNAI INSTITUTE OF TECHNOLOGY
87
CIRCUIT DIAGRAM:
FIG.6.1
MODEL GRAPH:
FIG.6.2
-
7/25/2019 Ec6411 EC II Lab Manual 2013
88/89
EC 6411-CIRCUIT AND SIMULATION INTEGRATED LABORATORY
DEPT.OF ECE CHENNAI INSTITUTE OF TECHNOLOGY
88
6. BUTTER WORTH FILTER
6.1 AIM:
To simulate a second order active low pass butter worth filterusing PSPICE
6.2 APPARATUS REQUIRED:
1. PC
2. PSPICE software
6.3 THEORY:
A second order filters can be constructed using RC-(resistor- capacitor) passive circuits, and they have been implemented for radio
frequency for cheap and simplicity. For audio frequency range,unfortunately the size for the inductor and capacitor become too large,
space consuming, and the most important is theyre really expensive.
Because of this, active filter is commonly used for audio application.
6.4 PROCEDURE:
1. Click on the start menu and select the p spice simulation software
2. Select the parts required for the circuit from the parts menu and
place them in the work space3. Connect the parts using wires
4. Save the file and select the appropriate analysis
5. Simulate the circuit and observe the corresponding output
waveforms
-
7/25/2019 Ec6411 EC II Lab Manual 2013
89/89
EC 6411-CIRCUIT AND SIMULATION INTEGRATED LABORATORY
89
QUESTIONS:
1. Calculate the cutoff frequency from the graph.
2. What is butter worth filter?
3. How second order varies from first order.
4. What is active filter?
5. Give the application of second order filter.