1.0580 1.0580Data Table forSteel Grades:1.0580Mechanical Properties of Materialsof grade steel:1.0580Tensile strength, Flexural strength, Compressive strength, Shear Strength, Tensional strength, Reduction area, Yield Strength, Elongation.Chemical composition % of the ladle analysis of steel grade:1.0580

Chemical composition % of grade E355 (1.0580)P max =0.025%; S max =0.025%; Al min =0.02% (EN 10305-1:2010)

CSiMnPS

max 0.22max 0.55max 1.6max 0.045max 0.045

Mechanical properties of grade E355 (1.0580)

Rm- Tensile strength (MPa) (+U)540

Rm- Tensile strength (MPa) (+A)450-490

Rm- Tensile strength (MPa) (+N)490-630

Nominal thickness (mm): to 1616 - 4040 - 6565 - 100

Rm- Tensile strength (MPa) (+AR)490490490470

Rm- Tensile strength (MPa) (+C)640

Rm- Tensile strength (MPa) (+LC)580-590

Rm- Tensile strength (MPa) (+SR)580-590

ReH- Minimum yield strength (MPa) (+U)400

ReH- Minimum yield strength (MPa) (+N)355

Nominal thickness (mm): to 1616 - 4040 - 6565 - 8080 - 100

ReH- Minimum yield strength (MPa) (+AR)355345335315295

ReH- Minimum yield strength (MPa) (+SR)435-450

A- Min. elongation at fracture (%) (+A) or (+N)22

A- Min. elongation at fracture (%) (+U)5

A- Min. elongation at fracture (%) longitud., (+AR)20

A- Min. elongation at fracture (%) (+C)4

A- Min. elongation at fracture (%) (+SR)10

A- Min. elongation at fracture (%) (+A)22

A- Min. elongation at fracture (%) (+LC)6-7

Technological properties of grade steel:1.0580
Hardness and heat treatment specification of steel grade:1.0580

Mechanical Properties,Hardness and heat treatment specification.Machinability,Welding,Hot Working,Cold Working, Annealing,Tempering,Hardening,Heat treatment,etc.Annealing hardness
HBSCold pull hardness
HBSPreheating temperature
Quenching temperature
Holding time
minHardening mediumTemper temperature
After tempering hardness
HRC

salt-bath furnacecontrolled atmosphere furnace

23526278811911204515air cooling52260

Steel plate/Sheet
thickness / mmb
MPas
/MPa
Samples from the standard for 50 mm (2 in)180 of cold bending test

longitudinalhorizontal

Hot-rolled/Cold rolling:5 - 15052041516182a3.5a

Note:
(1) listed in the table apex diameter (d), to steel thickness (a) multiples said.
(2) in the ASTM A6 standard specified scope can meet any additional conditions.
(3) from the standard for 50 mm (2 in).
Mechanical properties ofManusteelcn.
Mechanische Eigenschaften ofManusteelcn.
Caracteristiques mecaniques ofManusteelcn.
ReHMinimum yield strength / Mindestwert der oberen Streckgrenze / Limite delasticite minimale
RmTensile strength / Zugfestigkeit / Resistance a la traction
AMinimum elongation / Mindestwert der Bruchdehnung / Allongement minimal
JNotch impact test / Kerbschlagbiegeversuch / Essai de flexion par choc

ManusteelcnChina steel suppliers - Superior technology, Advanced equipment, Perfect procedure!
Steel description:Manusteelcn.Step Shaft: steel plate/sheet,coil,round bar,flat bar,tube/pipe,Profiled forgingsManusteelcnsteel Specifications or Size:Round bar:Diameter: 1mm-2000mmSquare bar:Size: 50mm * 50mm-600mm *600mmPlate steel/flat bar:Size: Thickness: 0.1mm-800mm Width: 10mm to 1500mmTube/pipe:Size: OD: 6-219mm WT: 1-35 mm.Cold-rolled sheet: Thickness: 2-5mm Width:1000mm Length: 2000mmHot-rolled sheet: Thickness:6-80mm Width: 210-610mmLength: We can supply any length based on the customer's requirement.Forging/hot rolling/ extrusion of steel.Forging: Shafts with flanks/pipes/tubes/slugs/donuts/cubes/other shapesFinished goods condition: hot forging/hot rolling + annealing/normalizing + tempering/quenching + tempering/any conditions based on the customer's requirementSurface conditions: scaled (hot working finish)/ground/rough machining/fine machining/based on the customer's requirementFurnaces for metallurgical processing:electrodearc + LF/VD/VOD/ESR/Vacuum consumable electrode.Ultrasonic inspection: 100% ultrasonic inspection for anyin-perfectionsor based on the customer's requirement.UTS according to SEP 1921 C/c,D/d,E/e;A388 or GB/T 6402Excellent service for all kinds of industries, with advantages of technologies, equipment and price.Weserveyou with our honesty, integrity, andProfessionality.
Hot keywords of steel grade:1.0580