5 mm & 6 mm Allen Wrenches included#2 Phillips Screwdriver or Drill/Driver

Caution! Do not exceed maximum (payload) weight limit of 110 lb. This includes monitors, optional monitor brackets and all equipment on both surfaces.

1 of 4 Workrite Ergonomics | 800.959.9675 www.workriteergo.com

1 Attach Keyboard Platform Bracket to Keyboard PlatformAttach the Keyboard Platform Bracket (C) to the Keyboard Platform (B) using four 5M×10 mm Allen Head Screws (E) using the 5 mm Allen Wrench (G).

I M4×24 mm Phillips Head Screws Qty: 4

J M4×12 mm Phillips Head Screws Qty: 4

K 13 mm Spacers Qty: 4

H M6 Allen wrench Qty: 1

G M5 Allen wrench Qty: 1

A Solace Electric Base Qty: 1 B Keyboard Platform

Qty: 1

C Keyboard Platform Bracket Qty: 1

F M6×12 mm Allen Head Screws Qty: 4

E M5×10 mm Allen Head Screws Qty: 4

D Single Monitor Mount Qty: 1

Parts Included

Assembly & Installation Instructions:Solace Electric SOL-E-DT-B

Tools Required

Optional, Sold Separately

Monitor Mount Kit

Dual Monitor Bracket Triple Monitor Bracket

2 Attach Monitor Mount to the Solace Electric Monitor Arm2.1 Attach the Single Monitor Mount (D) to the Monitor Arm on the Solace

Electric Base (A) using four 6M×12 mm Allen Head Screws (F) using the 6 mm Allen Wrench (H).

Note: If you have purchased either the optional Dual Monitor or Triple Monitor Brackets, attach them in the same fashion.

2.2 For taller users, an additional 3" of height can be achieved by mounting the Single Monitor Mount (D) in the optional "Top Mounting" position as shown.

B

CE

2.1

2.2

A

F

D

Monitor Arm

Bottom

Optional Top Mounting

Single Monitor Bracket

Shown upside-down

Optional Triple Monitor BracketOptional Dual Monitor Bracket

2 of 4 Workrite Ergonomics | 800.959.9675 www.workriteergo.com

3 Plug in Solace Electric Base to Wall Power & Raise3.1 Plug in the Solace Electric Base (A) into 110 V power.

3.2 Raise the unit to its highest level by pressing the UP (+)arrow until the worksurface reaches its highest level and stops. The display should read "58" mm.

Note: Go to www.workriteergo.com/instructions and find Solace Electric Control User Guide for instructions on how to change from centimeters to inches.

4 Install the Keyboard Platform4.1 Unlock the Keyboard Platform Clamps on the bottom of the Worksurface by pivoting down.

4.2 Insert the Keyboard Platform assembly into the channels in the bottom of the Solace Electric Base Worksurface until the Keyboard Platform Bracket (C) is flush with the front of the Worksurface.

4.3 Lock the Keyboard Platform Bracket in place by pivoting the Keyboard Platform Clamps up.

3.1

3.2

Up Button

Unlock From Below

Lock From Below

3 of 4 Workrite Ergonomics | 800.959.9675 www.workriteergo.com

5 Mount Monitors to VESA PlateIf possible, use the Monitor Mount screws from your Monitor to attach your monitor to the VESA plate. Otherwise use the shortest screws possible from the included hardware kit (I or J) Use Spacers (K) for recessed monitor mounts.

Note: Mounting on the optional Dual or Triple Monitor Mounts is performed in the same fashion.

6 Consult the User Guide for your Electric SwitchGo to www.workriteergo.com/instructions to find Solace Electric Control User Guide for instructions on how to set up this product for ideal ergonomic benefit.

Single Monitor Shown

100 mm VESA standard, use 4 outer corner holes.

Important Note: It is strongly recommended to use the mounting screws provided by the monitor manufacturer if possible. If longer screws are required, use the shortest screws possible and Spacers to avoid damage to the monitor.

75 mm VESA standard, use 4 inner corner holes.

KJI

1500408 Rev B

4 of 4 Workrite Ergonomics | 800.959.9675 www.workriteergo.com