Copyright © 2010 DuPont. All rights reserved. The DuPont Oval Logo and all trademarks listed herein with ® or ™ are trademarks or registered trademarks of E.I. du Pont de Nemours and Company or its affiliates.

A DuPont OEM / Commercial Finishes Product

DuPont™ VelvaShield® RKP27687™ Interior Clear Coat Type A two-component, 3.5 VOC, urethane clear coat for internal application.

Description A high performance, soft and tactile feeling interior coating that delivers excellent mar and chemical resistance. This product meets OEM performance specifications.

Recommended For Use Over For use over properly prepared plastics, pigmented DuPont™ VelvaShield® products and select DuPont topcoats (consult your DuPont representative). Some plastics, such as TPO, may require adhesion promoters or other pretreatments. Not Recommended For Immersion service Compatible With Other Coatings Compatible with all DuPont OEM/ Commercial Finishes primers, select DuPont topcoats (consult your DuPont representative), and pigmented DuPont™ VelvaShield® products.

Dry Film Characteristics Chemical Resistance EXCELLENT Precipitation, windex, ford glass cleaner, coffee, soda, mustard, tobacco stain and various other materials & chemicals. Humidity Resistance EXCELLENT Weatherability EXCELLENT Acid Resistance EXCELLENT Alkali Resistance EXCELLENT Solvent Resistance VERU GOOD

Mix Ratio DuPont™ VelvaShield® RKP27687™ and activator should be conditioned to 70-80°F (21-27°C) prior to mixing. Hand stir DuPont™ VelvaShield® RKP27687™ thoroughly to ensure uniform. Combine components and mix thoroughly. Do not mechanically agitate. Two Component System Parts by Volume DuPont™ VelvaShield® RKP27687™ 4 DuPont™ VelvaShield® RKP26253™ Activator 1

Pot Life and Induction Time No induction time is required. Pot life is ½ - 1 hr at 70ºF (21°C)

Application Conditions Do not apply if material, substrate or ambient temperature is less than 50°F (10°C) or above 110°F (43°C). The substrate must be at least 5°F (3°C) below the dew point. Relative humidity should be below 90%.

°F / °C

Copyright © 2010 DuPont. All rights reserved. The DuPont Oval Logo and all trademarks listed herein with ® or ™ are trademarks or registered trademarks of E.I. du Pont de Nemours and Company or its affiliates.

A DuPont OEM / Commercial Finishes Product

Application Plural equipment is recommended. DuPont™ VelvaShield® builds at approximately 1.1-1.5 mils per pass with a recommended setup. Apply using a

cross-coat technique, top-to-bottom, then side-to-side. Each coat should be medium-wet. No flash time is required between coats.

Paint heaters can help provide a smoother appearance by controlling the temperature and viscosity of the product, especially under adverse or changing conditions.

Dry Time 77°F (25°C) & 50% Rh at recommended film thickness Force Dry (recommended): 30 minutes @160-180°F (71-82°C) minimum part temperature. Air dry: 4 – 6 hrs Application Equipment Suggested application is HVLP. Use the following or equivalent set-up: DeVilbiss JGHV gun, 46MP air cap, FF needle (.055), FF tip (1.4 mm), 8-10 psi @ cap & 10-12 fluid oz/min For siphon application, set air pressure to 60-70 psi @ gun. For pressure pot application, set fluid delivery to 10-12 oz/min, and set air pressure to 55-65 psi at the gun.

Maximum Service Temperature 200°F (92°C) in continuous service 300°F (148°C) in intermittent heat

Volume Solids 47.5% unactivated 52.0% RTS mixed 4:1 with DuPont™ RKP26253™ Activator

Weight Solids 56.76% unactivated 60.5% RTS mixed 4:1 with DuPont™ RKP26253™ Activator

Weight Per Gallon 8.69 lbs/gal average unactivated Suggested Dry Film Thickness 1.5 – 2.0 mils

Theoretical Coverage Per Gallon 834 sq. ft./gal average @ 1 mil DFT

Gloss Low

Color Clear

Flash Point (Closed Cup) 20-73°F (-7-23°C)

Shelf Life 12 months minimum

Copyright © 2010 DuPont. All rights reserved. The DuPont Oval Logo and all trademarks listed herein with ® or ™ are trademarks or registered trademarks of E.I. du Pont de Nemours and Company or its affiliates.

A DuPont OEM / Commercial Finishes Product

Application Solvents Ready-to-spray below 3.5 lbs/gal VOC upon activation. Further reduction may result in greater than 3.5 lbs/gal VOC.

Cleanup Solvents DuPont™ 3602S™ Thinner DuPont™ 8685S™ Reducer DuPont™ 32030S™ Thinner

Environmental VOC content (lbs/gal) LE AP DuPont™ VelvaShield® RKP27687™ Clear Coat 2.8 2.2 Mixed 4:1 with DuPont™ RKP26253™ Activator 2.1 1.8

For VOC Regulated Areas These directions refer to the use of products that may be restricted or require special mixing instructions in your area. Follow recommendations in the DuPont Compliant Products Chart for your area.

Safety And Handling DuPont is committed to helping you develop and maintain a safe working environment. Carefully read the specific warnings and precautions printed on the labels of all DuPont products before handling and using. These products are for industrial use by trained professional painters only. Ready to use paint materials containing isocyanates can cause irritation of the respiratory organs and hypersensitive reactions. Asthma sufferers, those with allergies and anyone with a history of respiratory complaints must not be asked to work with products containing isocyanates. Do not sand, flame cut, braze or weld dry coating without a NIOSH approved air purifying respirator with particulate filters or appropriate ventilation, and gloves.

01/10