Installation Layout

Dual Flush Valve Instruction

CD

Fill val ve

Water-inlet triangle washer

Water-inlet plastic washer

Water-inlet / J;;iJ, hexagonal nut/ +t

Water-supply pipe Wa ter

Water-stop cup

Water-inlet bod

Water-inlet triangle washer

Water- inlet ~ pl as ti c washer ~ ~

Water-supp ly pipe Wa ter-i nlet hexagon al nut

Wa ter tank

Flush va lve

11111 1. Read all m ani pulati on and in stall ati on guide lin e, and please install it st ep by step according to th e in stallati on guide line and preve nt any damage from prod uct breakage and improper use.

2. A ll materi al are w ritten acco rding t o the latest info rm ation w hen design . Our company re serve the right to change product charact erizes , packa ge and supply at any t im e w ith out noti ce.

3 . Do not use corro sive detergent (s uch as hypochlorite) in w ater tank beca use such strong oxidant make s fittin gs dam aged eas ily and lead to lea kage. The m enti oned above si tuati ons are beyond the range of our guarantee.

4 . Our com pa ny do not bea r th e relat ed loses and dam ages ca used by use oth er company' s parts and materia l such as glass glu e.

5. Su itabl e te mperature range: 0 - 45°C

Functional Instruction

1. Th e flu sh valve has 2 flu shing w ays : half-flush and ful l flu sh; w hen yo u push th e full flu sh, the discharge volume is big and w hen you push the half flush, the discharge volume is smal l. 2 . W ater leve l of half f lush is adju stab le. (Refe r to photo 6) 3 . Water leve l of full flush is adjustable . (Refer to photo 3-2)

Installation Steps

I , Preparation before Installation

Remove the old f ittings an d wash tan k before in stallation. And wash clean because many impurities proba bly existed in conduit.

ll , Flush Valve Installation (According to the actual need)

1. Stainless steel hook for one-piece flush valve installation

va lve

Contra rotate dra inage body and make it remove from pedestal.

Bolt

Circ um rotate sta inless st ee l hoo k to the e nd of bol t c lockwise .

--------~ @

Sea ling washer §

~ Circumrota te bol t by screwd river and be sure that seal between sea ling w asher and the surrounding for outfal l.

2. Two-piece flush valve installation

Let pedestal aim at the water tank scupper, def lect properly, circumrotate, and, the stain less steel hook ca n reach the scupper downside, then, revise the pedesta l, the seali ng w asher should put upside. Go th rough the pedestal by the m iddle f inger of left hand to keep off stai nless steel hook and make its both sides put around the outfa ll symmetrical ly.

®~t Flush ':Jf valve

Cont ra rotate drainage body and make it removed from pedestal .

@ Drain age ~i;~R~~

Drainage plastic

,. washer I ::::::::::5 2 I t ~ Drainage n

Standard washer

Let pedestal inse rt into ou t fall from in side of w ater tan k, cove r th e d rainage p las ti c w asher, circumrota t e dra inage nut and cover t he standard w asher, and it can ad just th e put ang le prope rly according to t he actu al size of w at er ta nk .

Notice: If the product is different from the photo shown, please refer to the actual product.

Let flush valve body insert into pedesta l and circu m rotate it inside the buck le clockw ise.

Let f lush valve body insert into pedesta l and circumrota te it inside th e buckle clockwise.

--¾>>

III, Fill Valve Installation Put f ill valve & water- ,-:,;;--., Adjust water level: inlet triangle washer ~ Fetch out buckle and insert into water- inlet W ter screw off water- inlet body hole of water tank, ~ ~ anti- clockwise: pull upside then, cover water- inlet W Pn--rn!T7',-, or press downside to the

. plastic washer and -inf!r proper situation, then, I filter built hexagonal nut in turn body _,,......__.,.,,,.. screwing on water- inlet

1.._ya-+.!......,,n ~ittom from the bottom of fil l body closely and install Water-inlet 1-..?:

1

water valve. Fastening water the buckle.Little (;;~~~i r / t ~ et pipe -inlet hexagonal nut adjustment on water level:

Filter and make a proper revolve adjusted rod to . adjust according to the Water-in let pipe adjust the height of water

Water-,nlet hexagonal nut size of water tank. ~-------~ -stop cup and buoy to reach the suitable water level vou need.

@

U:'v""" t ff--Adapter ~ Water-

. supply pipe

Connect water - supply pipe and built in adapter or filter according to your actual need. Notice: 1 . Be sure that buoy is active freely before fill va~e installation. 2.Wash the impurity in the conduit when you connectng water-supply pipe. 3The height of water level can not beyond overflow mouth of flush valve when adjusting water level.

V , Water tank Installation Put w ater t ank on ceram ic toi let and make sta ndard washer located at the out fal l of t oi let. Just th e photo shows, let jointed bolt inse rt into installat ion hole, then, screw t he join ted nut c lose ly .

loll Wa sher J:olt j ~~__,_ ~~Cemm;c ,oBe<

Joint nut ---1liil Standard washe r VI . Examination

CD

Water-stop cup

Wa ter-inlet pl ast ic washer

Water tank

Dra inage tri angle washe r

As photo show , connect w ater-inlet pipe to test and notice the fo llow ing phenomenon: 1. According to the height of ha lf f lush to adjust half f lush water level :

w hen half flush buoy is higher, the drainage volume is less; w hen it is lower, the drainage volume is more.

2. Adjust the height of w ater level by the adjusted digit and its correspond ing adjusted patch . The placket is big and its water level is high; the placket is sma ll and its water level is low (N ote: W hen adjust ing full flush w ater level, please fetch out f lush valve, then, install f lush valve again correct ly afte r adjusted.)

3. Adj ust all parts position to prevent th em from interference. 4. Open & close for w ater-stop cup is normal and has no leakage. 5. It is normal fo r full fl ush and half fl ush .

VII, Push button Installation

VIII ,

@ ~Push button nut Full flush l ~ sh button

f Ha~ flush I push button Screw of f push bu t ton nu t .

@) ,I, Push~~

:~~eli~rl t Push button Adjus~Jt nu1

Let push button insert into water tank lid middle hole, screwing on push button nut from the bottom of water tank lid, then, screwing the adjusted nut closely and be sure that it is firm.

Pull flush rod

ll~~ess

f flush key-press

Please confirm pull flush rod press the fl ush valve key-press w hether or not and check it is blocked or not

7-

Note: Screw off pull flush rod, the cut pa rt is upside.

Note: Pul l f lush rod should aim at the full f lush key- press.

Examination Again Cove r w ate r tank lid and not ice the followi ng phenomenon to conf irm installati on complete or not : 1.0pen & close for w ater - stop w asher is norma l and has no leakage.

Trouble Shooting 2. It is normal for f ull flu sh and half f lush and they f lush excel lently .

Symptoms Probable Reasons Corrective actions

Water level is too high or too low Do not adjust the water level of fill valve well Refer to photo 5 to adju st water level

1.Switch of fill valve is close 1.0pen the fill valve switch . Always water-inlet 2.Buoy is extrusive by water tank wall. or do not water-inlet

3.Filter has been blocked owing to bad water 2.Adjust fill valve direction .

(for fill valve) quality

3. Wash filter (refer to photo 3-1 ).

1.Fill valve nut is loose. 1.Screw the fill valve nut closely. 2.Flush valve does not installed well. 2.lnstall flush valve again according to its

3.Pull flush rod is too long to cling outfall installation step.

well (refer to photo 7-4 ). 3.A.Adjust the adjusted nut (refer to photo 7-2,3, Leakage 4) ; B.Shorten the pull flush rod.A is prior to B.

4.Flush valve body and pedestal does not match 4.lnstall again (refer to the installation of flush well. va lve).

5.Refill water pipe insert into overflow mouth 5.Refill water pipe depth can not beyond too deep. the height of water level.

No drainage or less drainage Pull flush rod is too short to press drainage pipe Adjust adjusted nut (refer to 7-2). Water level for half flush Water level does not adjusted well Adjust water level (refer to photo 6). is too hiah or too low

Check out our full range of Bathroom Suites Bathroom Suites By Range

Cloakroom Suites

Toilets

Bathroom Sinks / Wash Basins

Bidets

Baths

Wide variety of toilets Close Coupled Toilets

Wall Hung Toilets

Back To Wall Toilets

Furniture unit toilets

Huge Selection of Baths Acrylic Baths

Steel Baths

Shower baths

Freestanding baths

Small baths

Corner baths

Whirlpool baths

Don’t forget the important bathroom suite extras Bath panels

Toilet seats

https://www.plumbworld.co.uk/bathroom-suite-ranges-16-0000https://www.plumbworld.co.uk/bathroom-furniture-toilet-units-19337-0000https://www.plumbworld.co.uk/close-coupled-toilets-19336-0000https://www.plumbworld.co.uk/back-to-wall-toilets-2236-0000https://www.plumbworld.co.uk/freestanding-baths-34-0000https://www.plumbworld.co.uk/wall-hung-toilets-2323-0000https://www.plumbworld.co.uk/cloakroom-suites-1797-0000https://www.plumbworld.co.uk/whirlpool-baths-35-0000https://www.plumbworld.co.uk/bathroom-basins-bathroom-sinks-1594-0000https://www.plumbworld.co.uk/acrylic-baths-664-0000https://www.plumbworld.co.uk/shower-baths-1294-0000https://www.plumbworld.co.uk/corner-baths-751-0000https://www.plumbworld.co.uk/toilet-seats-54-0000https://www.plumbworld.co.uk/bathroom-basins-bathroom-sinks-1594-0000https://www.plumbworld.co.uk/steel-baths-1880-0000https://www.plumbworld.co.uk/small-baths-1798-0000https://www.plumbworld.co.uk/bath-panels-2086-0000https://www.plumbworld.co.uk/bidets-291-0000https://www.plumbworld.co.uk/toilets-146-0000https://www.plumbworld.co.uk/toilets-146-0000https://www.plumbworld.co.uk/baths-13-0000https://www.plumbworld.co.uk/baths-13-0000https://www.plumbworld.co.uk/bathroom-suites-12-0000