DT730/710/330/310 User’s Guide
Transcript of DT730/710/330/310 User’s Guide
DT730/DT710/DT330/DT310USER’S GUIDE
NEC Corporation2010 August
NWA-039300-001ISSUE 4.0
LIABILITY DISCLAIMER
NEC Corporation reserves the right to change the specifications, functions,or features, at any time, without notice. NEC Corporation has prepared this document for use by its employees andcustomers. The information contained herein is the property of NEC Cor-poration and shall not be reproduced without prior written approval fromNEC Corporation. All brand names and product names on this documentare trademarks or registered trademarks of their respective companies.
Copyright 2008-2010
NEC Corporation
1
2
3
i
TABLE OF CONTENTS
. INTRODUCTIONFACE LAYOUT ................................................................................... 1KEYS AND PARTS............................................................................. 8MENU KEY ......................................................................................... 14SIMPLE OPERATION BY MENU KEY AND CURSOR KEY.............. 16ICON DISPLAY................................................................................... 16SHORTCUT MENU ............................................................................ 17PROGRAMMABLE FEATURE KEYS................................................. 19SOFT KEYS........................................................................................ 21CONDITIONS FOR DT700 SERIES................................................... 25
.INSTALLATION PROCEDUREADJUSTING ANGLE OF TILT LEG.................................................... 27TO REMOVE TILT LEG...................................................................... 28TO ATTACH TILT LEG ....................................................................... 28CONNECTING LAN CABLE ............................................................... 29CONNECTING LINE CORD ............................................................... 30INSTALLING DIRECTORY CARD...................................................... 31ATTACHING HANDSET ..................................................................... 31INSTALLING/REMOVING KEY SET UNIT ....................................... 32WALL MOUNTING ............................................................................ 33
.TERMINAL SETUPSETUP WITH UP/DOWN KEY ........................................................... 37SETUP WITH FEATURE KEY............................................................ 38SETUP WITH MENU KEY FOR DT700 SERIES ............................... 42SETUP WITH MENU KEY FOR DT300 SERIES ............................... 91
4
5
ii
TABLE OF CONTENTS
.BASIC OPERATIONTO LOGIN .......................................................................................... 96TO LOGOUT ...................................................................................... 96TO MAKE AN EXTERNAL CALL........................................................ 97TO MAKE AN INTERNAL CALL ......................................................... 99TO ANSWER AN EXTERNAL CALL .................................................. 101TO ANSWER AN INTERNAL CALL ................................................... 103MULTILINE APPEARANCE................................................................ 104TO HOLD A CALL ............................................................................. 104TO PLACE A CALL ON EXCLUSIVE HOLD .................................... 105TO TRANSFER A CALL ..................................................................... 105HOW TO INPUT CHARACTERS ....................................................... 107SECURITY MODE ............................................................................. 121EMERGENCY CALL .......................................................................... 123
.FEATURE OPERATIONTO ORIGINATE A CALL USING SELECTIVE DIALING(DYNAMIC DIAL PAD, PRESET DIAL) .............................................. 125TO ORIGINATE A CALL USING SPEED CALLING(ONE-TOUCH SPEED CALLING KEYS)............................................ 126TO REGISTER NAME ON ONE-TOUCH SPEED CALLING KEY ..... 129TO ORIGINATE A CALL USING SPEED CALLING - STATION/GROUP ........................................................................... 129TO ORIGINATE A CALL USING SPEED CALLING - SYSTEM......... 129ACCOUNT CODE ............................................................................. 131FORCED ACCOUNT CODE............................................................... 131AUTHORIZATION CODE ................................................................... 131VOICE CALL ..................................................................................... 132
iii
TABLE OF CONTENTS
TO ANSWER A VOICE CALL HANDS FREE .................................. 133AUTOMATIC INTERCOM................................................................... 133MANUAL INTERCOM......................................................................... 134DIAL INTERCOM .............................................................................. 135CONFERENCE ................................................................................. 136TO ESTABLISH A BROKER CALL..................................................... 136TO ANSWER A CAMPED-ON CALL.................................................. 136CALL WAITING - ORIGINATING........................................................ 137CALL PARK ...................................................................................... 139CALL PICK-UP (GROUP)................................................................... 140CALL PICK-UP (DIRECT)................................................................... 140OUTGOING TRUNK QUEUING ......................................................... 141OFF-HOOK TRUNK QUEUING.......................................................... 141EXECUTIVE OVERRIDE.................................................................... 141LAST NUMBER REDIAL .................................................................... 142CALL FORWARDING - ALL CALLS ................................................... 142CALL FORWARDING - BUSY LINE ................................................... 144CALL FORWARDING - DON’T ANSWER .......................................... 145LOGGED OUT IP STATION - CALL DESTINATION ......................... 146CALL BACK ...................................................................................... 148TO SAVE AND REPEAT A NUMBER ................................................ 148TO LEAVE A MESSAGE .................................................................... 150TO ANSWER A MESSAGE ................................................................ 150VOICE MAIL SYSTEM........................................................................ 151MEET-ME PAGING ............................................................................ 151PAGING TRANSFER.......................................................................... 152BOSS/SECRETARY TRANSFER....................................................... 154BOSS/SECRETARY - MW LAMP CONTROL .................................. 154BOSS SECRETARY OVERRIDE ....................................................... 155
6
7
iv
TABLE OF CONTENTS
DO NOT DISTURB ........................................................................... 156CALL REDIRECT .............................................................................. 157PRIVACY .......................................................................................... 158PRIVACY RELEASE........................................................................... 159PHONEBOOK ................................................................................... 160CALL HISTORY ................................................................................ 170
.DIRECTORY OPERATIONTO ADD NEW DATA ......................................................................... 175TO CHANGE GROUP NAME ............................................................ 182TO FIND A REGISTERED DATA ....................................................... 184TO MAKE A CALL FROM DIRECTORY............................................. 198TO ADD PREFIX TO NUMBER ......................................................... 199TO EDIT DIRECTORY DATA ............................................................ 201TO DELETE ALL DATA ..................................................................... 202TO DELETE A SPECIFIC DATA ....................................................... 203
.CALL HISTORY OPERATIONFOR DT730 SERIES TO VIEW CALL HISTORY ................................................................. 206TO MAKE A CALL FROM CALL HISTORY ....................................... 208TO ADD CALL HISTORY DATA TO DIRECTORY ............................ 209TO EDIT DIRECTORY DATA FROM CALL HISTORY ...................... 212TO DELETE ALL DATA ..................................................................... 215TO DELETE A SPECIFIC DATA ....................................................... 216
FOR DT330 SERIES TO VIEW CALL HISTORY ................................................................. 218TO MAKE A CALL FROM CALL HISTORY ....................................... 221
8
9
1
v
TABLE OF CONTENTS
TO DELETE ALL DATA ..................................................................... 222TO DELETE A SPECIFIC DATA ....................................................... 223
.SPECIFICATIONSTECHNICAL SPECIFICATIONS......................................................... 225
.MENU LISTMENU LIST FOR DT730 SERIES ...................................................... 227MENU LIST FOR DT710 Series ......................................................... 234MENU LIST FOR DT330 Series ......................................................... 237
0.WEB PROGRAMMINGOUTLINE ............................................................................................ 239TO LOGIN........................................................................................... 240TO LOGOUT....................................................................................... 242HOW TO OPERATE ........................................................................... 244
This page is for your notes.
1.
1FAC
264
[mm
]
1
. INTRODUCTION
E LAYOUTITL-8LD-1 (DT730 Series) DTL-8LD-1 (DT330 Series)
1 2ABC
3DEF
4GHI
5JKL
6MNO
7PQRS
8TUV
9WXYZ
0 #
Menu
HOLD Transfer Speaker
Recall FeautreFeature
Answer Mic
Scroll
Exit Help
Redial
264
[mm
]
179 [mm]
1 2ABC
3DEF
4GHI
5JKL
6MNO
7PQRS
8TUV
9WXYZ
0 #
Menu
HOLD Transfer Speaker
Recall Feature
Answer Mic
Scroll
Exit Help
Redial
179 [mm]
1.
258
[mm
]
2ITL-32D-1 (DT730 Series) DTL-32D-1 (DT330 Series)
1 2ABC
3DEF
4GHI
5JKL
6MNO
7PQRS
8TUV
9WXYZ
0 #
Menu
HOLD Transfer Speaker
Recall Feature
Answer Mic
Exit Help
Redial
258
[mm
]
205.8 [mm]
1 2ABC
3DEF
4GHI
5JKL
6MNO
7PQRS
8TUV
9WXYZ
0 #
Menu
HOLD Transfer Speaker
Recall Feature
Answer Mic
Exit Help
Redial
205.8 [mm]
1.
258
[mm
]
3ITL-24D-1 (DT730 Series) DTL-24D-1 (DT330 Series)
1 2ABC
3DEF
4GHI
5JKL
6MNO
7PQRS
8TUV
9WXYZ
0 #
Menu
HOLD Transfer Speaker
Recall Feature
Answer Mic
Exit Help
Redial
258
[mm
]
179 [mm]
1 2ABC
3DEF
4GHI
5JKL
6MNO
7PQRS
8TUV
9WXYZ
0 #
Menu
HOLD Transfer Speaker
Recall Feature
Answer Mic
Exit Help
Redial
179 [mm]
1.
258
[mm
]
4ITL-12D-1 (DT730 Series) DTL-12D-1 (DT330 Series)
1 2ABC
3DEF
4GHI
5JKL
6MNO
7PQRS
8TUV
9WXYZ
0 #
Menu
HOLD Transfer Speaker
Recall Feature
Answer Mic
Exit Help
Redial
258
[mm
]
179 [mm]
1 2ABC
3DEF
4GHI
5JKL
6MNO
7PQRS
8TUV
9WXYZ
0 #
Menu
HOLD Transfer Speaker
Recall Feature
Answer Mic
Exit Help
Redial
179 [mm]
1.
258
[mm
]
5ITL-12PA-1 (DT730 Series) DTL-12PA-1 (DT330 Series)
1 2ABC
3DEF
4GHI
5JKL
6MNO
7PQRS
8TUV
9WXYZ
0 #
Menu
HOLD Transfer Speaker
Line
Recall Feature
Answer Mic
Exit Help
Redial
258
[mm
]
193 [mm]
1 2ABC
3DEF
4GHI
5JKL
6MNO
7PQRS
8TUV
9WXYZ
0 #
Menu
HOLD Transfer Speaker
Line
Recall Feature
Answer Mic
Exit Help
Redial
193 [mm]
1.
225
[mm
]
6ITL-6DE-1 (DT710 Series) DTL-6DE-1 (DT310 Series)
1 2ABC
3DEF
4GHI
5JKL
6MNO
7PQRS
8TUV
9WXYZ
0 #
Menu
HOLD Transfer Speaker
Recall Feature
Answer Mic
Exit Help
Redial
225
[mm
]
179 [mm]
1 2ABC
3DEF
4GHI
5JKL
6MNO
7PQRS
8TUV
9WXYZ
0 #
HOLD Transfer Speaker
Exit Help
Recall Feature
Redial Conf
Directory
Mic
Message
Answer
179 [mm]
1.
225
[mm
]
7ITL-2E-1 (DT710 Series) DTL-2E-1 (DT310 Series)
1 2ABC
3DEF
4GHI
5JKL
6MNO
7PQRS
8TUV
9WXYZ
0 #
HOLD Transfer Speaker
Recall Feature
Redial Conf
Directory
Mic
Message
Answer
225
[mm
]
179 [mm]
1 2ABC
3DEF
4GHI
5JKL
6MNO
7PQRS
8TUV
9WXYZ
0 #
HOLD Transfer Speaker
Recall Feature
Redial Conf
Directory
Mic
Message
Answer
179 [mm]
1.
KE
• K
This takin
rminal
y al. mp ft.
eries Key
the
is played pro-
up on
Line ny
“One-e keys, e num-
8
YS AND PARTS
EYS AND PARTS ON ITL-24D-1
subsection explains keys and parts of DT Seriesg ITL-24D-1 as an example.
(1) Security Button (DT730 only)You can prevent information leakage from teby simple operation.
(2) Call Indicator LampLamp at the top corner of DT Series Displaflashes when a call terminates to the terminAlso, when using Voice Mail service, the Lalights steadily when a message has been le
(3) LCDLCD (Liquid Crystal Display) provides DT Sactivity information plus date, time and SoftOperation.
(4) ExitTo exit Menu or Help mode and go back to time display.
(5) Soft KeysAny feature shown at the bottom of the LCDavailable. The appropriate feature key is dison the screen according to the call handlingcess.
(6) HelpExplanations of the Soft Keys can be calledthe LCD by pressing this key.
(7) Programmable KeysThese keys can be programmed as Flexiblekey/Programmable Feature Key by TelephoServer Administrator. When Telephony Server Administrator setsTouch Speed Dial key” on the programmablyou can assign any numbers (ex. Telephon
(1) (2)
1 2ABC
3DEF
4GHI
5JKL
6MNO
7PQRS
8TUV
9WXYZ
0 #
Menu
HOLD Transfer Speaker
Recall Feature
Answer Mic
Exit Help
Redial
(16) (15) (14)
(3)
(4)
(6)
(5)
(7)
(8)
(9)
(10)
(11)
(12)
(13)
1.
b
*T
*Ay
(8) RP
(9) FUfD
(10)Ww
(11)Pl
(12)TH
(13)Bv
ver vol-
sation.
.
roup)edial been ed,
r ORY
ia, Latinions]: #, Hong
OWN key)
IGHT key)
WN) key
9
er, etc.) to the key (up to 32 digits).
For the assignment of the keys, contact your elephony Server Administrator.
* When two telephone numbers are assigned on side and B side of “One-Touch Speed Dial key”, ou can switch the side by PAGE key (Soft key).
ecallress key to finish the call and hear the dial tone.
eaturesed to activate any features as terminal setup
unctions, etc. and to program One-Touch Speed ial Keys.
Answerhen LED on this key is lit, press key to answer a aiting call.
Micress key to respond hands free. LED on this key
ights during speakerphone operation.
Menuo access the local menu of DT750, such as Call istory, Directory or Terminal Setting.
Cursory using this key, DT Series user can access to arious features with simple operation.
Details on Cursor key
(a) Up/Down( DOWN UP)Used to adjust LCD contrast, speaker/receiume, and ringer volume.
• LCD Contrast:Press ( ) or ( ) key while idle.
• Speaker/Receiver Volume:Press ( ) or ( ) key during conver
• Ringer Volume:Press ( ) or ( ) key during ringing
(b) Redial(Last Number Call, Speed Calling-Station/GPress key to activate redial feature. Press rand scroll back through numbers that havedialed. When the desired number is displaypress the or # key to activate dialing.
(c) DirectoryPressing this key opens Directory menu. Fodetails on Directory service, see 6.DIRECTOPERATION.
Note: A-law Countries [Europe, Australia, RussAmerica, Middle near East, other Asian natµ-law Countries [North America, JapanKong, Taiwan]:
Enter Key
(4-way Scroll D
(4-way Scroll RDirectory key
(4-way Scroll UP key)
(4-way Scroll LEFT key) Redial key
Volume (UP) key
Volume (DO
(a)
(b)
(a)
(c)
(d)
1.
(Dqsd
At
(14)CHL*mm
(15)At
al call
d DTL-
oup)edial been
DTL-
on key
-1 and
fea-
-1 and
ia, Latintions]: #n, Hong
10
d) EnterT330/DT730 Series has shortcut menu for fre-uently-used features. Use this key to display the hortcut menu (see SHORTCUT MENU) and etermine the selected item in the menu.
lso, this key is used as cursor-movement key on he Menu screen.
Speakerontrols the built-in speaker which can be used forands Free dialing/monitoring.ED on key lights when key is active. DT730/DT330 support for full duplex hands-free ode. DT710/DT310 are half duplex hands-free ode.
Transferllows the station user to transfer established calls
o another station, without attendant assistance.
(16)HoldPress this key to place an internal or externon hold.
• THE OTHER KEYS AND PARTS
Redial (only for DTL-2E-1, ITL-2E-1 an6DE-1)
(Last Number Call, Speed Calling-Station/GrPress key to activate redial feature. Press rand scroll back through numbers that havedialed. When the desired number is displayed, press the or # key to activate dialing.
Conf (only for DTL-2E-1, ITL-2E-1 and6DE-1) Press key to establish a conversation. LED lights when key is active.
Directory (only for DTL-2E-1, ITL-2EDTL-6DE-1)Press key to activate speed calling - systemture.
Message (only for DTL-2E-1, ITL-2EDTL-6DE-1)Press key to access the voice mail system.
Up Move the highlighted area one line up the screen.
Down Move the highlighted area one line down the screen.
Left Go back to the previous screen.
Right Go to the screen which corresponds to the highlighted menu item.
Enter Go to the screen which corresponds to the highlighted menu item.
Note: A-law Countries [Europe, Australia, RussAmerica, Middle near East, other Asian naµ-law Countries [North America, JapaKong, Taiwan]:
1.
UD(Uu
83kagsp
WTybUCO
*T
Call ted as
shing ttern-
11
p/Down (only for DTL-2E-1, ITL-2E-1 andTL-6DE-1) DOWN UP)
sed to adjust LCD contrast, speaker/receiver vol-me, and ringer volume.• LCD Contrast:
Press ( ) or ( ) key while idle.• Speaker/Receiver Volume:
Press ( ) or ( ) key during conversation.• Ringer Volume:
Press ( ) or ( ) key during ringing.
LD Display (only for DTL-8LD-1/ITL-8LD-1)2 (8 keys x 4 pages) additional programmable eys (Flexible Line/Programmable Feature key) re provided. Also, information set to each pro-rammable key is displayed on 8LD display. For etting of the programmable key, contact Tele-hony Server Administrator.
hen Telephony Server Administrator sets “One-ouch Speed Dial key” on the programmable keys, ou can assign any numbers (ex. Telephone num-er, etc.) to the key (see TO ORIGINATE A CALL SING SPEED CALLING (ONE-TOUCH SPEED ALLING KEYS) and TO REGISTER NAME ON NE-TOUCH SPEED CALLING KEY).
For the assignment of the keys, confirm to the elephony Server Administrator.
(a) IconStatus information on the Line key such as termination, Call Hold or Busy can be indicafollowing Icons.
User Status Icon FlaPa
• Idle No Icon
GHI
Scroll
1
2
3
4
BENRACHEL JULIA
PaulJAMES
HANNAH
FDA
FDN
(a) (b) (C) (b) (a)
1.
(Pl
le keys y dis-able ll key.
• Ca(IndiCall • Ca(OthCall • ReCall Hold
• Re
• DuUse)• Ca• Co• DuUse)• Acfeatu
Line
OneSpee
Feat
icates ge.
ge with
ll termi-
12
b) Programmable Key Informationrogrammable Key Information displays the fol-
owings.
(c) Page Icon8LD display has four pages (8 programmabper page). Page Icon key indicates currentlplayed page. You can switch the programmkey display from page 1 to 4 by using Scro
.
ll Holdvidual Hold/Individual Hold on Park Group)
Blink
ll Holder Party Hold/Other Party Hold on Park Group)call (Individual Hold/Exclusive
Hold/Call Transfer/Individual on Call Park Group)
ceiving an Incoming Call
ring Conversation (Individual
ll Transfernference
Steady Litring Conversation (Other Party
tive Feature (Under a setting of re key like a “Call Forwarding”)
Key DescriptionMaximum
digits to be displayed
Key - Name and Number informa-tion 8 digits.
-Touch d Dial Key
- Speed Dial Name Informa-tion- Number Information
8 digits.
ure Key - Feature Name 6 difits.
User Status Icon Flashing Pattern
Programmable Key 1-8
Black background indcurrently displayed pa
Programmable Key 9-16
Programmable Key 17-24
Flashing indicates paevent happening.
Programmable Key 25-32
Note: The icon flashes during events such as canation to a line key or call back.
1
2
3
4
1.
Exam
Tm
to the by
hen mable
d.
h REG-LLING
code
h REG-LLING
Not
KeyKey
KeyKey
Key NKey N
Key NKey N
13
ple: Page Turning by Scroll Key
he following shows LCD indication of Program-able keys.
Appropriate icons are displayed according feature. These displays cannot be changeduser.
The following shows each LCD indication wOne-Touch Speed Dial key is set to Programkey.
When Station line/Trunk line are assigne
No icons are displayed.* You can register name on each One-ToucSpeed Dial key. For the procedures, see TOISTER NAME ON ONE-TOUCH SPEED CAKEY.
When any features using feature accessare assigned.
Icons turn black.* You can register name on each One-ToucSpeed Dial key. For the procedures, see TOISTER NAME ON ONE-TOUCH SPEED CAKEY.
e: For example, when an incoming call is terminatedto a line key on Page 3 while Page 1 is being dis-played on the screen, the screen is not automati-cally switched from Page 1 to page 3. You mustdisplay Page 3 manually and then answer theincoming call.
Scroll
Scroll
BENRACHEL LINDA
PAUL012345
HANNAH
FDA
FDN
No. 1 No. 2
No. 3 No. 4
Key No. 5Key No. 6Key No. 6Key No. 8
MICHAELPETER
JULIA
JAMES
POWELL
Switch Page
o. 17o. 18
o. 19o. 20
Key No. 21Key No. 22Key No. 23Key No. 24
Press Feature Key 22 on Page 3 to answer incoming call.
Page 1
Page 3IncomingCall
Press twice.
Flashing
1
2
3
4
12
3
4
OR
OR
1.
(3) STp
MEFromfeatu
To D
STE
o types e hand, rver nd, the
ry of the RIES in
re the eatures. by tele-
ECTO-
system. n chap-
d by the , please r.ML the
tant
me,
U KEY
setting ontact
14
croll Keyhis key is used to turn over the page of 8LD dis-lay.
NU KEY the key, you can use various applicationres such as Directory and Call History.
isplay Menu List
P 1: Press key while indicating the currenttime on LCD. The Menu List is displayed inLCD. Use Cursor Key to select desired MenuItem.
Main Menu for DT730 Series
Menu
Menu
12
Tool
[Menu]
3456#0
Call Func. SettingPresenceFavoriteConfig
Directory
OKBack
History
Menu Item Description
History
To view Call History. There are twof Call History features. On the onthe history data is stored in the se(system) memory. On the other hahistory data is stored in the memotelephone (see 7.1FOR DT730 SEchapter 7Call History Operation).
Directory
To use Directory features.There afollowing three types of directory f
• Personal Directory: Controlledphone set. For details, see 6.DIRRY OPERATION.• Phonebook: Controlled by the For details, see PHONEBOOK iter 5.• Corporate Directory: Controlleexternal XML server. For detailscontact the system administrato
Tool
- Uses when accessing external Xserver. For details, please contactsystem administrator.- Uses when sending/receiving InsMessage (Not used).
Call Func. Currently Not Used (grayed out).
SettingTo control settings for ringing voluLCD display, and Music on Hold.For details, see SETUP WITH MENFOR DT700 SERIES.
Presence Currently Not Used (grayed out).
Favorite Currently Not Used (grayed out).
ConfigThis item is used for Configurationof DT Series. For details, please cthe system administrator.
1
2
3
4
5
6
#
0
1.
Me
T
C
M
C
D
S
1
0
1
2
3
t have
15
Main Menu for DT710 Series
Main Menu for DT330 Series
nu Item Description
ool
- Uses when accessing external XML server. For details, please contact the system administrator.- Uses when sending/receiving Instant Message (Not used).
onfigThis item is used for Configuration setting of DT Series. For details, please contact the system administrator.
enu Item Description
all HistoryTo view Call History. For details, see 7.2FOR DT330 SERIES in chapter 7Call History Operation.
irectory To use Phonebook function. For details, see PHONEBOOK in Chapter 5.
ettingTo control settings for ringing volume, LCD display, and Music on Hold. For details, see SETUP WITH MENU KEY FOR DT300 SERIES.
10 Config
OKBack
Tool
12
[Menu]
3OKBack
SettingsDirectoryCall History
Note: DTL-6DE-1/ITL-2E-1/DTL-2E-1 does noMenu key.
Note: Unavailable Menu items are grayed out.
1.
SIMANBy uaccewith
As aacce
isplays events
9 WXY
#
Spea
e is a hecked
n of ou have ill
ntly sor key.
16
PLE OPERATION BY MENU KEY D CURSOR KEYsing key and key, DT Series user canss Call History, Directory and terminal settingssimple operation.
n example, the following operations show how toss the Directory menu.
ICON DISPLAYThe LCD of DT730 Series/DT330 Series dDesktop Icons which provide notification when(such as missed call and voice mail) occur.
Menu
GHI
Z Menu
ker
Answer Mic
Redial
Press Menu key
Press Directory key
2 Directory
1 Hisotry [Menu]
2 System 1 Personal [Directory]
3 Tool
Up Down Back OK
Up Down Back OK Up Down Back OK
Feature Icon Description
Missed CallThis icon appears when thermissed call. Once you have cthe missed call, this icon willdisappear.
Voice MailThis icon provides notificatioincoming Voice Mail. Once ychecked the mail, this icon wdisappear.
Cursor This icon indicates the curreavailable direction of the Cur
Encryption This icon appears when the conversation is encrypted.
4:26 PM MON 12 JUL 2010
Icon Display
DND >>>MIC
VM
1.
SHAs sSerieYou (Ente
Note
Shor
showsom the
menu
presst key.
d.
Not
M
V
IM
P
B
GH
9WXYZ
#
Speaker
R
1
2
3
4
5
e Mail.
17
ORTCUT MENUhown in the figure below, DT730 Series/DT330s has Shortcut Menu for frequently-used features.can access to Shortcut Menu by pressing
r) key.
: DT710 Series/DT310 Series do not supportthe Shortcut Menu.
tcut Menu includes the following features.
Shortcut Menu for DT730 Series
Shortcut Menu for DT330 Series
As an example of DT730 Series, the followinghow to view the log data of missed call frShortcut menu.
STEP 1: Press (Enter) key. The Shortcutscreen is displayed on LCD.
STEP 2: Select Missed Calls and then(Enter), (Right-cursor) or OK sof
STEP 3: The log data of the last call is displaye
e: Unavailable Menu items are grayed out.
Feature Description
issed Calls Access history of Missed Calls.
oice Mail Access history of incoming Voice Mail.
Currently Not Used (grayed out).
resence Currently Not Used (grayed out).
luetooth Currently Not Used (grayed out).
I
Menu
Answer Mic
edial
Press Enter Key
[Shortcut Menu]
2 Voice Mail3 Receive IM
Back OK
1/21 Missed Calls: 2
Feature Description
Missed Calls Access to history of Missed Call.
Voice Mail Access to history of incoming Voic
1
2
1
12
Receive IM
[Shortcut Menu]
340
PresenceBluetooth
Voice Mail
OKBack
Missed Calls
1.
STE
Not
Not
Not
Not
18
P 4: Press (Enter) key while displaying the logdata for the target telephone number on LCD.
e: If two or more records exist, use or softkey to display the next/former records.
e: For unanswered incoming calls, will be dis-played on the left of the name.
e: If you make/answer a call to/from the telephonenumber which is registered to Personal Directory,the corresponding name will be displayed as callhistory data.
e: While the log data is displayed, you cannot makea call by dialing a telephone number.
1
[Missed]
OptionBack
12/JUL/2010 (MON) 10:00Ken Kobus
7205
1.
PRThespresfeatuOtheadm
AICMPres
DICMPres
DNDPres
FDAPresCalls
FDBPres– Bu
FDNPres– Do
MICMPres
MSGPresansw
MULA prosee s
n
on
umber.
tion.
ouch
isplay:
19
OGRAMMABLE FEATURE KEYSe are examples of DT Series features available by
sing the programmable keys. Some features usingre access code may be programmed by the user.rs must be programmed by the telephone systeministrator.
:s key to activate “Automatic Intercom”.
:s key to activate “Dial Intercom”.
(Do Not Disturb):s key to activate or cancel “Privacy” feature.
:s key to activate or cancel “Call Forwarding – All ” feature.
:s key to activate, verify, or cancel “Call Forwarding sy Line” feature.
:s key to activate, verify, or cancel “Call Forwarding n’t Answer” feature.
:s key to activate “Manual Intercom”.
(Message):s key to leave message indication at station in no er or busy condition.
TILINE APPEARANCE:grammable extra extension key. Press this key to tatus of extra extension.
MW-SET:Press key to leave message waiting indication oboss’ station from secretary’s station.
MW-OFF:Press key to cancel message waiting indicationboss’ station from secretary’s station.
P-RLS:Press key to release “Privacy” feature.
S&R (Save and Repeat):Press key to store a number or redial a stored n
SIG:Press key to cause chime at predetermined sta
NAME:Press key to register name for the key to One-TSpeed Calling key.
RVERS:Press key to reverse the black and white in its dbackground, characters and icons.
1.
LEDProgEmitthe a
FunFeatFeatFeatFeatFeatFeatFeatFeatincomlight FeatPad,
Not
20
rammable Feature keys have a built-in Lightting Diode (LED) that lights or flashes according toctivity of that Feature key.
ction Key Activitiesure + 0 = Side Tone On/Off. (for handset)*ure + 1 = Turns microphone on or off.ure + 2 = Adjusts handset receiver volume.*ure + 3 = Selects ringer tone.*ure + 4 = Adjusts transmission/receiving volume.*ure + 5 = Activates hands-free operation.*ure + 6 = Deactivates hands-free operation.*ure + 7 = Turns call indicator lamp on or off for
ing call notification. (If turned off, this lamp will stillto indicate message waiting.)ure + 8 = Selects between Normal, Dynamic Dial and Preset Dial.
e: * indicates the services which are not availablefor DT700 Series.
1.
SOThe functof thprovindivbottofunctnampattethe skey i
Exit Prestime
HelpPresinfor
MIC Presdeacillum
DNDPres
ding togs are on the
istereddividual
Not
21
FT KEYSSoft Keys on the DT Series provide a set ofions on the LCD that adapt to the changing statee telephone. While default Soft Key settings areided, desired functions can be assigned toidual stations as required. The Soft Keys, at them of the LCD, can display the names of availableions, names of user-assigned functions andes of functions assigned by a specific Soft Keyrn. Displayed Soft Keys can vary, depending ontate of the phone and/or when the Next/Previouss pressed.
Keys to exit Menu or Help mode and go back to thedisplay.
Keys the Help Key, then desired Soft Key for helpfulmation about that key.
(Microphone)s the Soft Key below "MIC" to activate ortivate the Microphone. LED on MIC key willinate when MIC is on.
(Do Not Disturb)s the Soft Key to reject call termination to the
preassigned station.
Default Displays for Each StatusDefault Soft Key settings are provided corresponparticular functions. Different Soft Key settindisplayed at the bottom of the LCD dependingstatus, as shown below.
Different patterns of Soft Key settings can be regfor individual call status and assigned to interminals as required.
e: Soft Key function is available for the terminalswith LCD.
7:354051
>>>MIC AM MON 12 JUL 2010
Exit Help
DND4:26 PM MON 12 JUL 2010
MIC >>>DND
DIAL TONE/DIALING
IDLE
4:26 PM MON 12 JUL 2010MIC >>>PICK
(1)
Push >>>
4:26 PM MON 12 JUL 2010FDN >>>FDB
FDA
(2)
4:26 PM MON 12 JUL 2010MIC >>>VOICE
RINGING
1.
SoftWhenamblinkfeatuspec
erns of
diately
n to be or idle
n)ropriateATIONtered is
ering ainto the
cominge busyanswer
CALL as the
er andNot
BU
CO
(
(
CO
22
Key Featuresn the Soft Key corresponding to a desired featuree is operated, the selected feature name starts to on the LCD. The blinking display of availableres takes precedence over the display of featuresified by the Soft Key pattern.
The following shows the default display pattmain features.
FDB (Call Forwarding - Busy Line)Permits a call to a busy station to be immeforwarded to a predesignated station.
FDA (Call Forwarding - All Calls)Permits all calls designated for a particular statiorouted to another station regardless of the busystatus of the called station.
FDL (Logged Out IP Station - Call DestinatioEnables a system to transfer the call to appstation when Dterm whose LOGGED OUT IP ST- CALL DESTINATION has already been regisin logout status.
E-OVR (Executive Override)Enables selected station users, upon encountbusy condition at an internal station, to bridge busy connection.
CW (Call Waiting)Enables a busy station to receive a second incall. A camp-on indication tone is sent to thstation, and you can use a switchhook flash to the second call.
CB (Call Back)Provides the ability for a calling station to set aBACK. The calling station will be rung as soonbusy station becomes available.
S&R (Save and Repeat)Allows a station to save a specific dialed numbthen redial that number later.
e: The Soft Keys can be programmed in SystemData to blink, remain steady, have no indication,or display a character when either in use or idle.
4:26 PM MON 12 JUL 2010TRANSFER 2000
MIC >>>CONF
SY
NSULTATION HOLD
4:26 PM MON 12 JUL 2010BUSY 2000
MIC >>>CB1)
Push >>>
4:26 PM MON 12 JUL 2010BUSY 2000
S&R >>>
CW
2)
4:26 PM MON 12 JUL 20102000
MIC >>>DND
NNECTION
1.
MWSAllowlamp
HOLPermretur
MWOAllowor la
PICKPermothe
CONEnabconfealrea
VOICEnabspeacan c
S-SPAllownumthan
CASAllowoutsi
UCDAllow
wardedoes not
only.
Speedgroup.
ey andaged in
ion line
for use
umbers.
ing the
23
ET (Message Waiting - Set)s a station to set a Message Waiting indication or.
D (Call Hold)its a station user to hold a call in progress and to
n to the previously held call.
FF (Message Waiting - Cancel)s a station to cancel a Message Waiting indication
mp.
(Call Pickup - Group)its a station user to answer any calls directed to
r lines in the user's preset Call Pickup Group.
F (Three-way Calling)les a station user to establish a three-wayrence by connecting an additional party to andy existing conversation.
E (Voice Call)les you to make a call to the called party's built-inker. If the called party's MIC is on, the called partyonverse on hands-free.
D (Speed Calling - System)s a station user to call certain frequently dialed
bers using fewer digits (abbreviated call codes) would normally be required.
(CAS-Switch Hook Flash)s you to send a switchhook flash while on an
de trunk.
BO (UCD Busy Out)s a station user to block UCD calls and to cancel
Busy Out.FLASH (Flash)Provides the station with a switchhook flash.
FDN (Call Forward - No Answer)Permits a call to an unanswered station to be forto a predesignated station if the called station danswer within a predetermined period of time.
C-RPT (ISDN Malicious Call Trace)Allows you to initiate a Call Trace on ISDN calls
G-SPD (Speed Calling - Group)Allows a station user to share a set of commonCalling numbers with other station users in the P-RLS (Privacy Release)Allows another station to depress a busy line kenter the conversation of a station already engcommunication.
DND (Do Not Disturb)Allows a station user to deny access to the statfor incoming calls.
MIC (Microphone On/Off)Allows you to turn the microphone on and off with the speakerphone.
PAGE (Button Page)Allows you to toggle between pages when two nare registered on One-Touch Speed Calling key
HSET (Headset)Allows you to go off- and on-hook when usheadset.
1.
RLSAllohea
SIGPerpredfrominte
CKEAlloall i
SCAAlloexteannto d
IZPAlloof th
IDCAlloalte
GPIAlloexp
CHCAlloconano
ser is incovering
ringing.
display:
24
(Release Key)ws you to release the current call when using thedset, without waiting for the party to hang up.
(Manual Signaling)mits station users to send a one-second ring to aetermined station. If the signaled station is ringing another call, the manual intercom signal will
rrupt that ringing.
EP (Eight-Party Conference Retrain)ws all outside parties to stay on a conference whennternal parties hang up.
LL (Serial Call)ws you to set Serial Call for the caller beforending the call, allowing the caller to receive anouncement at the end of the call guiding the callerial the next number and subsequent numbers.
(Internal Zone Paging)ws a user to make a voice call through the speakerse designated group.
HG (Call ID Change Display)ws you to toggle between standard display and anrnate display.
CK (Call Pickup - Group Enhancement)ws you to answer any ringing station within youranded call pickup group.
NF (Call Hold - Conference)ws a station user to establish a conferencenection by adding a third party, who is held onther line, to the existing two-party connection.
VISIT (Survivable Remote MGC)Allows a station to indicate a status: when a uremote office, VISIT will be blinking. After rethe main office, VISIT will return to light.
RMUTE (Ringer Mute)Allows a station user to mute or recover station
RVERS:Allows you to reverse the black and white in itsbackground, characters and icons.
>>> (Display Function Next Page)Allows you to scroll to the next screen.
<<< (Display Function Previous Page)Allows you to scroll to the previous screen.
MIC DND RVERS >>> 1:25 PM MON 12 JUL 2010
MIC DND RVERS >>> 1:25 PM MON 12 JUL 2010
1.
COPleaKey
• Fe
• Fe
• Fe
• Fe
• Fe
• Fe
e menud. For MONI-
25
NDITIONS FOR DT700 SERIESse note that following terminal settings (by Feature+ Digit Key) cannot be used for DT700 Series.
ature+0 =Side Tone On/Off (for handset)For the settings, contact the Administrator.* You can confirm the settings in “Audio&Visual Set-tings” “Side Tone Volume” of Online Monitoring.
ature+2 =Adjusts handset receiver volumeFor the settings, contact the Administrator.* You can confirm the settings in “Audio&Visual Set-tings” “Audio Settings” “Receive Bias”/“Re-ceive Gain” of Online Monitoring.
ature+3 =Selects ringer toneFor the settings, contact the Administrator.* You can confirm the settings in “Audio&Visual Set-tings” “Audio Settings” “Ring Settings” of On-line Monitoring.
ature+4 =Adjusts transmission/receiving volumeFor the settings, contact the Administrator.* You can confirm the settings in “Audio&Visual Set-tings” “Audio Settings” “Receive Bias”/“Re-ceive Gain”/“Send Gain” of Online Monitoring.
ature+5 =Activates hands-free operationNot Available
ature+6 =Deactivates hands-free operationNot Available
Note: When pressing and holding Help key, thof "Online Monitoring" will be displayedetails on Online Monitoring, see ONLINETORING in Chapter 10.
1.
26
This page is for your notes.
2AD
The
•
STE
STE
, adjustw until
DT7
pper
27
. INSTALLATION PROCEDURE
JUSTING ANGLE OF TILT LEG
angle of the tilt leg can be adjusted in four levels.
TO RAISE TILT LEG
P 1: Turn the telephone set upside down.
P 2: Adjust the tilt leg in the direction of the arrowuntil you hear it click.
• TO LOWER TILT LEG
STEP 1: Turn the telephone set upside down.
STEP 2: While lifting the center of the stopperthe tilt leg in the direction of the arroyou hear it click.
30/710 DT330/310
First Level
Second Level
Third Level
Fourth Level
Tilt Leg
StoTilt Leg
TO
STE
STE
STE
STE
the ap- set.
(c and
e stop-tilt leg.
DT7
28
REMOVE TILT LEG
P 1: Turn the telephone set upside down.
P 2: Lower the tilt leg to first level.
P 3: Remove the indicated portions (a and b) ofthe stopper from grooves (A and B) on the tiltleg and then widen the tilt leg.
P 4: While pushing the two hooks, slide the tilt legdownward. Remove the tilt leg from the termi-nal.
TO ATTACH TILT LEG
STEP 1: Turn the telephone set upside down.
STEP 2: Align the hooks (c-h) of the tilt leg overpropriate slots (C-H) of the telephone
STEP 3: Slide the tilt leg upward until the hooksb) click into place.
STEP 4: Fit the indicated portions (a and b) of thper into the grooves (A and B) on the
30/710 DT330/310
Stopper
a
A B
b
Tilt Leg
d
c
DT730/710 DT330/310
f
g c
d
h
e
E C G
F D H
a
A B
b
CO
STE
STE
STE
STE
DT7
T
LA
lephone
d
Adapter
29
NNECTING LAN CABLE
P 1: Prepare 10 BASE-T/100 BASE-T/TX cables(Straight) for connecting the telephone to net-work device such as HUB, PoE Switch.
P 2: Connect the telephone to the network deviceusing the LAN cable.
P 3: Thread the LAN cable through the groove onthe back of the telephone.
P 4: When AC adapter is used to supply power tothe telephone, connect the AC/DC adapter tothe telephone as shown below.
30/710
elephone
To LAN
Groove N Straight Cable
To PC
Te
AC Adapter Plug AC Adapter Cor
Groove
Connector for AC
CO
STE
STE
STE
DT3
Telep
Telpe
Cord
30
NNECTING LINE CORD
P 1: Insert Line cord plug into Line connector onthe back of the telephone set until you hear itclick.
P 2: Thread the line cord through the groove onthe back of the telephone.
P 3: Lead the line cord out through the groove onthe tilt leg as shown in the figure below.
30/DT310
Line Cord Line Cord Plug
Line Connector
hone
Line Code Groove
hone
Tilt Leg
Groove
Line
INS
A dirtabledirecnumcard
STE
STE
NDSETne until
ove asNot
DT7
iled Cord
oove
ANDSET onnector
dular Plug
31
TALLING DIRECTORY CARD
ectory card (also known as an abbreviated dialing) can be attached to the telephone sets. Thetory card can be used to record often dialedbers or other important information. Directorys are available as options.
P 1: Remove the protective sheet from the cover.
P 2: Attach the cover to the directory card andthen attach it to the directory card holder.
ATTACHING HANDSET
STEP 1: Insert the coiled cord plug into HAconnector on the back of the telephoyou hear it click.
STEP 2: Thread the coiled cord through the groshown in the figure below.
e: To remove the directory card, pinch the two sidesof the directory card holder inward until the tabsrelease and pull the holder out of the grooves.
30/710 DT330/310
Cover
Directory Card
Holder Grooves
DT730/710 DT330/310
Telephone
Co
Gr
HC
Mo
INSUN
•
STE
STE
STE
•
STE
STE
el until
Lin
Butto
ey Card
32
TALLING/REMOVING KEY SET IT
TO REMOVE KEY SET UNIT
P 1: Insert a tapered rod lightly into the right sideof the line key panel/button panel.
P 2: Lift out the line key panel/button panel to re-move it from the telephone.
P 3: Remove the line key card.
TO INSTALL KEY SET UNIT
P 1: Align the holes in the line key card with thebuttons on the telephone.
P 2: Align the holes in the line key panel/buttonpanel with the buttons on the telephone and
then push the four corners of the panthe panel clicks into place.
DT730/710 DT330/310
e Key Panel
n Panel
Line Key Card
Line K
Line Key Panel
Button Panel
WAA watelepside
To mspac
se the
upside
t once.e hang-
nd wid-
or the
e wall
ws (in- WM-Ls (pur-all.
WA
SpaceModu
33
LL MOUNTING
ll mount unit (WM-L UNIT) is used to mount allhones to the wall. This unit connects to the backof the telephone.
ount the telephone set on the wall, the followinge is required.
To mount the telephone set on the wall, ufollowing procedure.
STEP 1: Mount the hanger of the handset down.
Remove the hanger from the handseTurn it upside down and then insert ther until you hear it clicks.
STEP 2: Turn the telephone set upside down aen the tilt leg.
STEP 3: Attach WM-L UNIT to the wall directlywall plate.
- When attaching WM-L UNIT to thdirectly:
Secure WM-L UNIT with the six screcluded with the telephone set) or hangUNIT on the wall with the two screwchased separately) inserted into the w
RNING Be careful not to drop the telephone set while mounting it on the wall. It can cause injury.Make sure the telephone set is firmly mounted on the wall to prevent the telephone set from falling out. It can cause injury.
DT730/710 DT330/310
Telephone
Tab Slots
for lar terminal
117.5
136
25 (approximately)
15 (approximately)
35 (approximately)
30 (approximately)
83.5 60
60
(In the case of 12D/24D)
All dimensions in mm
Handset Hanger
Telpehone
The Serie
- In- In
LA
STE
ith thector.
onnec- the ex-.
ove on the fig-
WM-L UN
inal
inal
34
- When attaching WM-L UNIT to the wall plate:
Attach WM-L UNIT to the posts on the wallplate as shown in the figure below.
remainder of the procedure varies between DT300s and DT700 Series.
the case of DT300 Series: Go to the next step. the case of DT700 Series: Go to Step 8 after theN cable is connected to the telephone.
P 4: Attach the modular terminal to the wall asshown in the following figure. If the modularconnector is attached directly on the wall orthe wall plate is used instead of modular ter-minal, skip this step.
STEP 5: Insert the line cord plug (included wtelephone set) into the modular conne
STEP 6: Insert the line cord plug into the LINE ctor on the back of the telephone. Wrapcess cord and secure it with a tie wrap
STEP 7: Thread the coiled cord through the grothe back of the telephone as shown inure below.
Wall Wall
Screws (suppulied)
Screws
IT WM-L UNIT
WM-L
Posts
Switch box
Wall WM-L
Modular Term
Line Code
Modular Term
STE
W
L
WM-L
Tabs
35
P 8: Insert the four tabs on WM-L UNIT in the tabslots on the back of the telephone.
Tuck the excess cord into WM-L UNIT.
all
ine Cord
Line Connector
Telephone
Groove
Modular Plug
Wall
Tab Slots
36
This page is for your notes.
3This termkey,
Variopasskey.
SET
• TV
Presstatu
LCD
during
ging.
37
. TERMINAL SETUP
chapter describes operating procedures forinal settings by the Up/Down ( or / )
key and key.
us terminal settings such as display, sounds,word, and language are also available from
UP WITH UP/DOWN KEY
O ADJUST HANDSET RECEIVER OLUME
s Up/Down ( or / ) key in the off-hooks or during the call.
indication for North America, Latin America, Asia, Middle East and Russia
LCD indication for Australia
• TO ADJUST SPEAKER VOLUME
Press Up/Down ( or / ) key speakerphone operation or during the call.
• TO ADJUST RINGER TONE
Press Up/Down ( or / ) key during rin
Feature Menu
Menu
DT730/710 DT330/310
HANDSET
HANDSET
DT730/710 DT330/310
SPEAKER
DT730/710 DT330/310
RING
• T
Presstatu
SET
• M
LEDmicro
STE
• TV
Hand
STE
ate be-
ou can
isplays
D
D
z)
/310
38
O ADJUST LCD CONTRAST
s Up/Down ( or / ) key in the on-hooks.
UP WITH FEATURE KEY
ICROPHONE ON/OFF
on key shows the status of the built-inphone.
P 1: Press soft key associated with the MIC Dis-play or press and key.
O CHANGE HANDSET RECEIVER OLUME set receiver volume can be changed.
P 1: Press and key. The LCD displaysthe current volume status.
STEP 2: Press and key to alterntween Large and Small volume.
• TO SELECT RINGER TONE DT Series has 10 kinds of ringer tones that yselect.
STEP 1: Press and key. The LCD dthe selected tone number (n=1 ~ 10).
T730/710 DT330/310
LCD
T730/710 DT330/310Mic
Feature 1
DT330/310
Feature 2
No. Frequency (Hz) Modulation (H1 520/660 162 520/660 83 1100/1400 164 660/760 165 Melody 16 Melody 27 Melody 3
4:26 PM MON 12 JUL 2010RCV VOL. SMALL
Feature 2
4:26 PM MON 12 JUL 2010RCV VOL. LARGE
DT330
Feature 3
4:26 PM MON 12 JUL 2010RINGER TONE n
Not
N
39
8 Melody 49 Melody 5
10 Melody 6
e: Tone number 5, 6, 8~10 (Melody 1, 2, 4~6) willsound continuously.
o. Frequency (Hz) Modulation (Hz)
• TI
Hand
STE
STE
• TTo S
STE
To SSTE
ither on
isplays:
ic Dial
d as a turned
40
O ADJUST TRANSMISSION/RECEIV-NG VOLUME set volume can be changed.
P 1: Press and key. The LCD displaysthe current volume.
P 2: Press and key again to alternatebetween Large and Small volume.
O ACTIVATE HANDS-FREE et Hands-Free On:
P 1: Press and key. The LCD displays:
et Hands-Free Off:P 1: Press and key. The LCD displays:
• CALL INDICATOR LAMP ON/OFF
You can choose to turn the call indicator lamp eor off during ringing.
STEP 1: Press and key. The LCD d
• SELECT DIAL MODE
You can select one pattern from Normal, DynamPad or Preset Dial to originate a call.
When only Dynamic Dial Pad is activated:
DT330/310
Feature 4
4:26 PM MON 12 JUL 2010T/R VOL. SMALL
Feature 4
4:26 PM MON 12 JUL 2010T/R VOL. LARGE
DT330/310
Feature 5
4:26 PM MON 12 JUL 2010HANDS FREE ON
Feature 6
Note: The call indicator lamp lights when useMessage Waiting Lamp, even when it isoff by the above operation.
4:26 PM MON 12 JUL 2010HANDS FREE OFF
DT730/710 DT330/310
Feature 7
4:26 PM MON 12 JUL 2010INDICATOR ON
4:26 PM MON 12 JUL 2010INDICATOR OFF
DT730/710 DT330/310
To S
STE
Whe
To S
STE
ial are
ressed,s:
Not
Not
is ON.
41
et/Reset Dynamic Dial Pad
P 1: Press and key. The LCD displays:
n only Preset Dial is activated:
et/Reset Preset Dial
P 1: Press and key. The LCD displays:
When both Dynamic Dial Pad and Preset Dactivated:
To Set Dial Mode
STEP 1: Every time and key are pDial Mode switches. The LCD display
e: When this feature is ON, you may initiate a callby immediately dialing the number and the sta-tion will go hands-free off-hook automatically. Fordetails, see TO ORIGINATE A CALL USINGSELECTIVE DIALING (DYNAMIC DIAL PAD,PRESET DIAL).
e: When this feature is ON, you may initiate a callby pressing Speaker Key or going off-hook afterdialing the number. For details, see TO ORIGI-NATE A CALL USING SELECTIVE DIALING(DYNAMIC DIAL PAD, PRESET DIAL)
Feature 8
4:26 PM MON 12 JUL 2010Direct Dial Pad ON
4:26 PM MON 12 JUL 2010Direct Dial Pad OFF
Feature 8
4:26 PM MON 12 JUL 2010Preset Dial ON
4:26 PM MON 12 JUL 2010Preset Dial OFF
Note: It means that Dial Mode displayed on LCD
Feature 8
4:26 PM MON 12 JUL 2010Dial Mode: Direct
4:26 PM MON 12 JUL 2010Dial Mode: Preset
4:26 PM MON 12 JUL 2010Dial Mode: Normal
SETDT7
• TR
The hook
STE
STE
STE
ons.ss ,
ons.ss ,
Off-
ons.ss ,
1
42
UP WITH MENU KEY FOR 00 SERIES
O ENABLE/DISABLE OFF-HOOK INGING
procedure below shows how to enable/disable Off- ringing.
P 1: While indicating the current time on LCD,press key to open the Menu screen.
P 2: Select Setting (DT730) / Setting(DT710)Select an item by either of the following operations.• Highlight an item by using , and then press ,
or OK soft key.• Press key (DT730) / key (DT710)
P 3: Select User Setting.
Select an item by either of the following operati• Highlight an item by using , and then pre
or OK soft key.• Press key.
STEP 4: Select Incoming Call.Select an item by either of the following operati• Highlight an item by using , and then pre
or OK soft key.• Press key.
STEP 5: Select Offhook Ring (DT730) / hook Ring (DT710)Select an item by either of the following operati• Highlight an item by using , and then pre
DT730/DT710
Menu
5 2
5 2
12
Tool
[Menu]
3456#0
Call Func.
PresenceFavoriteConfig
Directory
OKBack
History
Setting
1
1
12
Data Backup/Restore
[Setting]
3Download
OKBack
User Setting
1
1
12
Display
[User Setting]
34560
Change Password
PeripheralsSetting Reset
Talk
OKBack
Security
Incoming Call
2
STE
Not
Not
43
or OK soft key.• Press key (DT730) / key (DT710)
P 6: To disable/enable the off-hook ringing, selectDisable or Enable.
Select an item by one of the following operations.• Highlight an item by using , and then press
or OK soft key.• Press or key, and then press or OK soft
key.
e: Default setting is 2 Enable.
e: The enabled item is highlighted.
2 1
12
Headset Ring
[Incoming Call]
3456
Ring Tone
Headset Ring VolumeOKBack
Illumination
Ring VolumeOffhook Ring
1 2
1 2
[Offhook Ring]
OKBack
12
DisableEnable
• T
The ringin
STE
STE
STE
ons.ss ,
ons.ss ,
44
O SET RINGING OF HEADSET
procedure below shows how to enable/disable theg of headset.
P 1: While indicating the current time on LCD,press key to open the Menu screen.
P 2: Select Setting.Select an item by either of the following operations.• Highlight an item by using , and then press ,
or OK soft key.• Press key.
P 3: Select User Setting.Select an item by either of the following operations.• Highlight an item by using , and then press ,
or OK soft key.• Press key.
STEP 4: Select Incoming Call.Select an item by either of the following operati• Highlight an item by using , and then pre
or OK soft key.• Press key.
STEP 5: Select Headset Ring.Select an item by either of the following operati• Highlight an item by using , and then pre
or OK soft key.• Press key.
DT730
Menu
5
5
12
Tool
[Menu]
3456#0
Call Func.
PresenceFavoriteConfig
Directory
OKBack
History
Setting
1
1
12
Data Backup/Restore
[Setting]
3Download
OKBack
User Setting
1
1
12
Display
[User Setting]
34560
Change Password
PeripheralsSetting Reset
Talk
OKBack
Security
Incoming Call
3
3
STE
Not
Not
45
P 6: To disable/enable the ringing of headset, se-lect Disable or Enable. Select an item by one of the following operations.• Highlight an item by using , and then press
or OK soft key.• Press or key, and then press or OK soft
key.
e: Default setting is 1 Disable.
e: The enabled item is highlighted.
12
[Incoming Call]
3456
Ring Tone
Headset Ring VolumeOKBack
Illumination
Ring VolumeOffhook Ring
Headset Ring
1 2
1 2
[Headset Ring]
OKBack
12 Enable
Disable
• T
The tone
STE
STE
STE
ons.ss ,
Ring
ons.ss ,
46
O SET RINGER TONE
procedure below shows how to change the ringer for internal call and external call.
P 1: While indicating the current time on LCD,press key to open the Menu screen.
P 2: Select Setting (DT730) / Setting(DT710)Select an item by either of the following operations.• Highlight an item by using , and then press ,
or OK soft key.• Press key (DT730) / key (DT710)
P 3: Select User Setting.Select an item by either of the following operations.• Highlight an item by using , and then press ,
or OK soft key.• Press key.
STEP 4: Select Incoming Call.Select an item by either of the following operati• Highlight an item by using , and then pre
or OK soft key.• Press key.
STEP 5: Select Ring Tone (DT730) / Tone (DT710)Select an item by either of the following operati• Highlight an item by using , and then pre
or OK soft key.• Press key (DT730) / key (DT710)
DT730/DT710
Menu
5 2
5 2
12
Tool
[Menu]
3456#0
Call Func.
PresenceFavoriteConfig
Directory
OKBack
History
Setting
1
1
12
Data Backup/Restore
[Setting]
3Download
OKBack
User Setting
1
1
12
Display
[User Setting]
34560
Change Password
PeripheralsSetting Reset
Talk
OKBack
Security
Incoming Call
4 2
4 2
STE
STE
rks
ulationulation
47
P 6: Select External Call when setting theringer tone for external calls. Select Inter-nal Call when setting the ringer tone for inter-nal calls.Select an item by either of the following operations.• Highlight an item by using , and then press ,
or OK soft key.• Press or key.
P 7: Select a desired tone type. You can previewdesignated ringer tone.
Select an item by either of the following operations.• Highlight an item by using , and then press
or OK soft key.• Press - key, and then press or OK soft
key.For example, press + to select
Download1.12
[Incoming Call]
3456 Headset Ring Volume
OKBack
Illumination
Ring VolumeOffhook Ring
Headset RingRing Tone
12
1 2
12
IM
[Ring Tone]
3Internal Call
OKBack
External Call
0 9
Note: The enabled item is highlighted.
No. Menu ItemFrequency (Hz)
Rema1st 2nd
0 Automatic 520 660 16Hz mod1 Tone Type1 520 660 16Hz mod
1 515
01
[External Call]
234567
Automatic
OKBack
Tone Type1
89
16151413121110
17
Tone Type2Tone Type3
Tone Type10Tone Type11
Tone Type5Tone Type4
Tone Type6Tone Type7Tone Type8Tone Type9
Tone Type12Tone Type13Tone Type14Download1Download2Download3
2345678
9
1011121314151617
Not
Not
Not
No.e,
ails,
set me", one n the
48
Tone Type2 520 660 8Hz modulationTone Type3 1400 1100 Door PhoneTone Type4 1100 No modulationTone Type5 540 No modulationTone Type6 1100 1400 16Hz modulationTone Type7 660 760 16Hz modulationTone Type8 1100 Envelope
Tone Type9 -Door Phone
MelodyTone Type10 - Melody 1Tone Type11 - Melody 2Tone Type12 - Melody 3Tone Type13 - Melody 4Tone Type14 - Melody 5Download1 - DT730 onlyDownload2 - DT730 onlyDownload3 - DT730 only
e: When selecting Automatic or not performing this ringer tone setting, Tone Type 1 is automatically applied.
e: When selecting Automatic, the preview function will not operate. Also, when selecting Download 1/2/3, the ringer tone file must be downloaded in advance. If there is no downloaded file, you hear no tone.
e: Tone Type 1 to Tone Type 8:In the preview function, each ringer tone soundscontinuously. Actual ringer pattern of each tone isdetermined by the initial system settings.
Menu ItemFrequency (Hz)
Remarks1st 2nd
Note: Terminal settings may not become effectivaccording as the system settings. For detcontact the System Administrator.
Note: You can set ringer tone for the telephone here. Ringer Tone type can be set for "Na"Group" and "Telephone set". The ringer Ttype set for "Name" has higher priority thatypes set for "Group" and "Terminal set".
• TC
The patte
STE
STE
STE
ons.ss ,
ons.ss ,
49
O SET ILLUMINATION PATTERN FOR ALL INDICATION LAMP
procedure below shows how to set the illuminationrn (color of Call Indicator Lamp).
P 1: While indicating the current time on LCD,press key to open the Menu screen.
P 2: Select Setting.Select an item by either of the following operations.• Highlight an item by using , and then press ,
or OK soft key.• Press key.
P 3: Select User Setting.Select an item by either of the following operations.• Highlight an item by using , and then press ,
or OK soft key.• Press key.
STEP 4: Select Incoming Call.Select an item by either of the following operati• Highlight an item by using , and then pre
or OK soft key.• Press key.
STEP 5: Select Illumination.Select an item by either of the following operati• Highlight an item by using , and then pre
or OK soft key.• Press key.
DT730
Menu
5
5
12
Tool
[Menu]
3456#0
Call Func.
PresenceFavoriteConfig
Directory
OKBack
History
Setting
1
1
12
Data Backup/Restore
[Setting]
3Download
OKBack
User Setting
1
1
12
Display
[User Setting]
34560
Change Password
PeripheralsSetting Reset
Talk
OKBack
Security
Incoming Call
5
5
STE
STE
OK soft
function
ing thispplied.
ephoneset fore illumi- priorityerminal
50
P 6: Select External Call when setting the illu-mination pattern for external calls. Select
Internal Call when setting the illuminationpattern for internal call.Select an item by one of the following operations.• Highlight an item by using , and then press ,
or OK soft key.• Press or key.
P 7: Select a desired illumination pattern.You canpreview the designated illumination pattern.Select an item by either of the following operations.• Highlight an item by using , and then press
or OK soft key.
• Press - key, and then press orkey.
12
[Incoming Call]
3456 Headset Ring Volume
OKBack
Ring VolumeOffhook Ring
Headset RingRing ToneIllumination
1
2
1 2
12
[Illumination]
3 IMOKBack
External Call
Internal Call
Note: When selecting Automatic, the preview will not operate.
Note: When selecting Automatic or not performillumination setting, Red is automatically a
Note: You can set illumination pattern for the telset here. Illumination pattern can be "Name", "Group" and "Telephone set". Thnation pattern set for "Name" has higherthan the patterns set for "Group" and "Tset".
0 9
01
[External Call]
234567
Automatic
OKBack
Disable
89
RedGreen
YellowBlue
PurpleLight BlueWhiteRotation
• T
The RTP
STE
STE
STE
ons.ss ,
ons.ss ,
D
51
O ENABLE/DISABLE RTP ALARM
procedure below shows how to enable/disable alarm.
P 1: While indicating the current time on LCD,press key to open the Menu screen.
P 2: Select Setting (DT730) / Setting(DT710)Select an item by either of the following operations.• Highlight an item by using , and then press ,
or OK soft key.• Press key (DT730) / key (DT710)
P 3: Select User Setting.Select an item by either of the following operations.• Highlight an item by using , and then press ,
or OK soft key.• Press key.
STEP 4: Select Talk.Select an item by either of the following operati• Highlight an item by using , and then pre
or OK soft key.• Press key.
STEP 5: Select RTP Alarm.Select an item by either of the following operati• Highlight an item by using , and then pre
or OK soft key.• Press key.
T730/DT710
Menu
5 2
5 2
12
Tool
[Menu]
3456#0
Call Func.
PresenceFavoriteConfig
Directory
OKBack
History
Setting
1
1
12
Data Backup/Restore
[Setting]
3Download
OKBack
User Setting
2
2
12
Display
[User Setting]
34560
Change Password
PeripheralsSetting Reset
OKBack
Security
Incoming CallTalk
1
1
STE
M
0 A
1 D
2 E
he Sys-
52
P 6: Select Automatic, Disable or En-able (see the following table).Select an item by either of the following operations.• Highlight an item by using , and then press
or OK soft key.• Press - key, and then press or OK soft
key.
enu Items Descriptions
utomatic
Follow the setting on the System. If no setting is made in the Sys-tem, the default setting (Alarm=ON) is applied.
isable Follow the setting on the terminal (OFF).
nable Follow the setting on the terminal (ON).
12
[Talk]
345
OKBack
DTMF ToneKey Touch ToneHold MusicPrefix
RTP Alarm
0 1 2
0 2
01
[RTP Alarm]
2
Automatic
OKBack
DisableEnable
Note: For the setting on the System, contact ttem Administrator.
Note: The enabled item is highlighted.
• T
The DTM
STE
STE
STE
ons.ss ,
ons.ss ,
D
53
O ENABLE/DISABLE DTMF TONE
procedure below shows how to enable/disableF Tone.
P 1: While indicating the current time on LCD,press key to open the Menu screen.
P 2: Select Setting (DT730) / Setting(DT710)Select an item by either of the following operations.• Highlight an item by using , and then press ,
or OK soft key.• Press key (DT730) / (DT710)
P 3: Select User Setting.Select an item by either of the following operations.• Highlight an item by using , and then press ,
or OK soft key.• Press key.
STEP 4: Select Talk.Select an item by either of the following operati• Highlight an item by using , and then pre
or OK soft key.• Press key.
STEP 5: Select DTMF Tone.Select an item by either of the following operati• Highlight an item by using , and then pre
or OK soft key.• Press key.
T730/DT710
Menu
5 2
5 2
12
Tool
[Menu]
3456#0
Call Func.
PresenceFavoriteConfig
Directory
OKBack
History
Setting
1
1
12
Data Backup/Restore
[Setting]
3Download
OKBack
User Setting
2
2
12
Display
[User Setting]
34560
Change Password
PeripheralsSetting Reset
OKBack
Security
Incoming CallTalk
2
2
STE
stem. Sys-
rminal
rminal
he Sys-
54
P 6: Select Automatic, Disable or En-able (see the following table).Select an item by either of the following operations.• Highlight an item by using , and then press
or OK soft key.• Press - key, and then press or OK soft
key.
12
[Talk]
345
OKBack
Key Touch ToneHold MusicPrefix
RTP AlarmDTMF Tone
0 1 2
0 2
01
[DTMF Tone]
2
OKBack
DisableAutomatic
Enable
Menu Items Descriptions
0 Automatic
Follow the setting on the SyIf no setting is made in the tem, the default setting (DTMF=ON) is applied.
1 Disable Follow the setting on the te(OFF).
2 Enable Follow the setting on the te(ON).
Note: For the setting on the System, contact ttem Administrator.
Note: The enabled item is highlighted.
• T
The Tonedigit
STE
STE
STE
ons.ss ,
ons.ss ,
D
55
O SET KEY TOUCH TONE
procedure below shows how to set Key Touch. Key Touch Tone is a tone generated when thekeys are pressed while DT Series is off-hook.
P 1: While indicating the current time on LCD,press key to open the Menu screen.
P 2: Select Setting (DT730) / Setting(DT710)Select an item by either of the following operations.• Highlight an item by using , and then press ,
or OK soft key.• Press key (DT730) / key (DT710)
P 3: Select User Setting.Select an item by either of the following operations.• Highlight an item by using , and then press ,
or OK soft key.
• Press key.
STEP 4: Select Talk.Select an item by either of the following operati• Highlight an item by using , and then pre
or OK soft key.• Press key.
STEP 5: Select Key Touch Tone.Select an item by either of the following operati• Highlight an item by using , and then pre
or OK soft key.• Press key.
T730/DT710
Menu
5 2
5 2
12
Tool
[Menu]
3456#0
Call Func.
PresenceFavoriteConfig
Directory
OKBack
History
Setting
1
1
12
Data Backup/Restore
[Setting]
3Download
OKBack
User Setting
2
2
12
Display
[User Setting]
34560
Change Password
PeripheralsSetting Reset
OKBack
Security
Incoming CallTalk
3
3
STE
Not
NotNot
56
P 6: Select Automatic, No Tone, Toneor Voice.Select an item by either of the following operations.• Highlight an item by using , and then press
or OK soft key.• Press - key, and then press or OK soft
key.
e: When 0 Automatic is set, the default setting(Tone) is applied.
e: The enabled item is highlighted.e: 3 Voice can be selected on DT730 only.
12
[Talk]
345
OKBack
Hold MusicPrefix
RTP AlarmDTMF Tone
Key Touch Tone
0 1 23
0 3
01
[Key Touch Tone]
2
OKBack
No Tone
Tone
Automatic
3 Voice
• T
The to be
STE
STE
STE
ons.ss ,
ons.ss ,
57
O SET MUSIC ON HOLD
procedure below shows how to set Music on Hold heard by DT Series user.
P 1: While indicating the current time on LCD,press key to open the Menu screen.
P 2: Select Setting (DT730) / Setting(DT710)Select an item by either of the following operations.• Highlight an item by using , and then press ,
or OK soft key.• Press key (DT730) / key (DT710)
P 3: Select User Setting.Select an item by either of the following operations.• Highlight an item by using , and then press ,
or OK soft key.• Press key.
STEP 4: Select Talk.Select an item by either of the following operati• Highlight an item by using , and then pre
or OK soft key.• Press key.
STEP 5: Select Hold Music.Select an item by either of the following operati• Highlight an item by using , and then pre
or OK soft key.• Press key.
DT730/DT710
Menu
5 2
5 2
12
Tool
[Menu]
3456#0
Call Func.
PresenceFavoriteConfig
Directory
OKBack
History
Setting
1
1
12
Data Backup/Restore
[Setting]
3Download
OKBack
User Setting
2
2
12
Display
[User Setting]
34560
Change Password
PeripheralsSetting Reset
OKBack
Security
Incoming CallTalk
4
4
STE
n hold.hold filee is nopreviewMinuet”
58
P 6: Select a desired Music on Hold. You can pre-view the designated Music on Hold.
Select Default when the default data (Minuet) is used as Music on Hold. Select Download when a downloaded data is used as Music on Hold.
Select an item by either of the following operations.• Highlight an item by using , and then press
or OK soft key.• Press or key, and then press or OK soft
key.
12
[Talk]
345
OKBackPrefix
RTP AlarmDTMF Tone
Key Touch ToneHold Music
12
1 2
12
[Hold Music]
OKBack
Download
Default
Note: You can preview the designated music oWhen selecting Download, the music on must be downloaded in advance. If therdownloaded file, you hear no tone in the function (in actual operating conditions, “is automatically applied.).
• T
Dete24-h
STE
STE
STE
ons.ss ,
ons.ss ,
Not
59
O SET CLOCK FORMAT
rmines whether time is displayed with a 12-hour orour clock format.
P 1: While indicating the current time on LCD,press key to open the Menu screen.
P 2: Select Setting (DT730) / Setting(DT710)Select an item by either of the following operations.• Highlight an item by using , and then press ,
or OK soft key.• Press key (DT730) / key (DT710)
P 3: Select User Setting.Select an item by either of the following operations.• Highlight an item by using , and then press ,
or OK soft key.• Press key.
STEP 4: Select Display.Select an item by either of the following operati• Highlight an item by using , and then pre
or OK soft key.• Press key.
STEP 5: Select Time Format.Select an item by either of the following operati• Highlight an item by using , and then pre
or OK soft key.• Press key.
e: This setting is available for Time Display only.Call Log feature displays the time in 24-hour for-mat regardless of this setting (DT730).
DT730/DT710
Menu
5 2
5 2
12
Tool
[Menu]
3456#0
Call Func.
PresenceFavoriteConfig
Directory
OKBack
History
Setting
1
1
12
Data Backup/Restore
[Setting]
3Download
OKBack
User Setting
3
3
12
[User Setting]
34560
Change Password
PeripheralsSetting Reset
OKBack
Security
Incoming CallTalk
Display
1
1
STE
0 Au
1 122 24
Not
Not
60
P 6: Make a selection from the following list.Select an item by either of the following operations.• Highlight an item by using , and then press
or OK soft key.• Press - key, and then press or OK soft
key.
Menu Item Meaning
tomaticFollow the setting on the system. (default)
hour Indication 12-hour clock hour Indication 24-hour clock
e: For the setting on the System, contact the Sys-tem Administrator.
e: The enabled item is highlighted.
12
[Display]
3456
Back Light
LanguageOKBack
Font Size
Local VolumeScreen Saver
Time Format
0 2
01
[Time Format]
2
OKBack
12 hour Indication
24 hour Indication
Automatic
• TD
Detevolumvolum
STE
STE
STE
ons.ss ,
ons.ss ,
61
O ENABLE/DISABLE VOLUME LEVEL ISPLAY
rmines whether or not to display the followinge levels: handset receiver volume, speakere, ringer tone volume and LCD contrast.
P 1: While indicating the current time on LCD,press key to open the Menu screen.
P 2: Select Setting (DT730) / Setting(DT710)Select an item by either of the following operations.• Highlight an item by using , and then press ,
or OK soft key.• Press key (DT730) / key (DT710)
P 3: Select User Setting.Select an item by either of the following operations.• Highlight an item by using , and then press ,
or OK soft key.
• Press key.
STEP 4: Select Display.Select an item by either of the following operati• Highlight an item by using , and then pre
or OK soft key.• Press key.
STEP 5: Select Local Volume.Select an item by either of the following operati• Highlight an item by using , and then pre
or OK soft key.• Press key.
DT730/DT710
Menu
5 2
5 2
12
Tool
[Menu]
3456#0
Call Func.
PresenceFavoriteConfig
Directory
OKBack
History
Setting
1
1
12
Data Backup/Restore
[Setting]
3Download
OKBack
User Setting
3
3
12
[User Setting]
34560
Change Password
PeripheralsSetting Reset
OKBack
Security
Incoming CallTalk
Display
2
2
ST
0
1
2
No
62
EP 6: Make a selection from the following list.Select an item by either of the following operations.• Highlight an item by using , and then press
or OK soft key.• Press - key, and then press or OK soft
key.
Menu Item Meaning
AutomaticEach volume level is displayed on LCD (default).
DisableEach volume level is not displayed on LCD.
EnableEach volume level is displayed on LCD.
te: The enabled item is highlighted.
12
[Display]
3456
Back Light
LanguageOKBack
Font Size
Screen Saver
Time FormatLocal Volume
0 2
01
[Local Volume]
2
OKBack
Disable
Enable
Automatic
• T
Screcertawill bSavedownbe d
STE
STE
ons.ss ,
ons.ss ,
Not
63
O SET SCREEN SAVER
en Saver works after the telephone is idle for ain period of time. The latest Screen Saver contentse displayed from XML server when the Screenr works. If the latest contents can not beloaded from XML server, default Screen Saver will
isplayed.
P 1: While indicating the current time on LCD,press key to open the Menu screen.
P 2: Select Setting (DT730) / Setting(DT710) on the Menu screen. Select an item by either of the following operations.• Highlight an item by using , and then press ,
or OK soft key.• Press key (DT730) / key (DT710)
STEP 3: Select User Setting.Select an item by either of the following operati• Highlight an item by using , and then pre
or OK soft key.• Press key.
STEP 4: Select Display.Select an item by either of the following operati• Highlight an item by using , and then pre
or OK soft key.• Press key.
e: For details on the XML service, contact the Sys-tem Administrator.
DT730/DT710
Menu
5 2
5 2
12
Tool
[Menu]
3456#0
Call Func.
PresenceFavoriteConfig
Directory
OKBack
History
Setting
1
1
12
Data Backup/Restore
[Setting]
3Download
OKBack
User Setting
3
3
12
[User Setting]
34560
Change Password
PeripheralsSetting Reset
OKBack
Security
Incoming CallTalk
Display
STE
STE
STE
r OK soft
SaverStep 7,
999min)
64
P 5: Select Screen Saver.Select an item by either of the following operations.• Highlight an item by using , and then press ,
or OK soft key.• Press key.
P 6: Select Screen Saver Mode.Select an item by either of the following operations.• Highlight an item by using , and then press ,
or OK soft key.• Press key.
P 7: Select either Disable or Enable.Select an item by one of the following operations.• Highlight an item by using , and then press
or OK soft key.
• Press or key, and then press okey.
STEP 8: The display goes back to the Screenscreen. When Enable is selected Select Wait Time.Input Wait Time to launch the screen saver (1-and then press or OK soft key.
3
3
12
[Display]
3456
Back Light
LanguageOKBack
Font Size
Local VolumeScreen Saver
Time Format
1
1
12
[Screen Saver]
OKBack
Screen Saver Mode Wait Time
1 2
Note: Default setting is 1 Disable.
Note: The enabled item is highlighted.
Note: Default value is 120 min.
1 2
12
[Screen Saver]
OKBack
Enable
Disable
22
OKBackBK
1[Wait Time]Input wait time.
1201-999(min)
• T
The back
The seco
STE
STE
STE
ons.ss ,
ons.ss ,
D
65
O ENABLE/DISABLE BACKLIGHT
following explains how to enable/disable thelights of LCD and digit keys.
backlights illuminate (for approximately 10nds) when you press any key or lifts the handset.
P 1: While indicating the current time on LCD,press key to open the Menu screen.
P 2: Select Setting.Select an item by either of the following operations.• Highlight an item by using , and then press ,
or OK soft key.• Press key.
P 3: Select User Setting.Select an item by either of the following operations.• Highlight an item by using , and then press ,
or OK soft key.• Press key.
STEP 4: Select Display.Select an item by either of the following operati• Highlight an item by using , and then pre
or OK soft key.• Press key.
STEP 5: Select Back Light.Select an item by either of the following operati• Highlight an item by using , and then pre
or OK soft key.• Press key.
T730
Menu
5
5
12
Tool
[Menu]
3456#0
Call Func.
PresenceFavoriteConfig
Directory
OKBack
History
Setting
1
1
12
Data Backup/Restore
[Setting]
3Download
OKBack
User Setting
3
3
12
[User Setting]
34560
Change Password
PeripheralsSetting Reset
OKBack
Security
Incoming CallTalk
Display
4
4
STE
1 D
2 En
Not
66
P 6: Make a selection from the following list.Select an item by either of the following operations.• Highlight an item by using , and then press
or OK soft key.• Press or key, and then press or OK soft
key.
Menu Item Meaning
isableBacklights of LCD and digit keys are disabled.
ableBacklights of LCD and digit keys are enabled.
e: The enabled item is highlighted.
12
[Display]
3456 Language
OKBack
Font Size
Screen Saver
Time FormatLocal Volume
Back Light
1 2
12
[Back Light]
OKBack
Disable
Enable
• T
The char
STE
STE
STE
ons.ss ,
ons.ss ,
67
O CHANGE CHARACTER SIZE
following explains how to change the displayedacter size on the LCD.
P 1: While indicating the current time on LCD,press key to open the Menu screen.
P 2: Select Setting.Select an item by either of the following operations.• Highlight an item by using , and then press ,
or OK soft key.• Press key.
P 3: Select User Setting.Select an item by either of the following operations.• Highlight an item by using , and then press ,
or OK soft key.• Press key.
STEP 4: Select Display.Select an item by either of the following operati• Highlight an item by using , and then pre
or OK soft key.• Press key.
STEP 5: Select Font Size.Select an item by either of the following operati• Highlight an item by using , and then pre
or OK soft key.• Press key.
DT730
Menu
5
5
12
Tool
[Menu]
3456#0
Call Func.
PresenceFavoriteConfig
Directory
OKBack
History
Setting
1
1
12
Data Backup/Restore
[Setting]
3Download
OKBack
User Setting
3
3
12
[User Setting]
34560
Change Password
PeripheralsSetting Reset
OKBack
Security
Incoming CallTalk
Display
5
5
STE
Not
68
P 6: Select either “Standard(16dot)“ or “Small(12dot)“.Select an item by either of the following operations.• Highlight an item by using , and then press
or OK soft key.• Press or key, and then press or OK soft
key.
e: The enabled item is highlighted.
12
[Display]
3456 Language
OKBack
Screen Saver
Time FormatLocal Volume
Back LightFont Size
1 2
12
[Font Size]
OKBack
Small(12dot)
Standard (16dot)
• T
The displ
STE
STE
STE
ons.ss ,
Lan-
ons.ss ,
69
O SET A LANGUAGE
following explains how to set a language to beayed on LCD.
P 1: While indicating the current time on LCD,press key to open the Menu screen.
P 2: Select Setting (DT730) / Setting(DT710)Select an item by either of the following operations.• Highlight an item by using , and then press ,
or OK soft key.• Press key (DT730) / key (DT710)
P 3: Select User Setting.Select an item by either of the following operations.• Highlight an item by using , and then press ,
or OK soft key.• Press key.
STEP 4: Select Display.Select an item by either of the following operati• Highlight an item by using , and then pre
or OK soft key.• Press key.
STEP 5: Select Language (DT730) / guage (DT710)Select an item by either of the following operati• Highlight an item by using , and then pre
or OK soft key.• Press key (DT730) / key (DT710)
DT730/DT710
Menu
5 2
5 2
12
Tool
[Menu]
3456#0
Call Func.
PresenceFavoriteConfig
Directory
OKBack
History
Setting
1
1
12
Data Backup/Restore
[Setting]
3Download
OKBack
User Setting
3
3
12
[User Setting]
34560
Change Password
PeripheralsSetting Reset
OKBack
Security
Incoming CallTalk
Display
6 4
6 4
STE
or OK
70
P 6: Select a desired language. Select an item by either of the following operations.• Highlight an item by using , and then press
or OK soft key.• Press - key, and then press or OK soft
key.For example, press + to select Spanish.
STEP 7: After Making a selection, press soft key.
12
[Display]
3456
OKBack
Screen Saver
Time FormatLocal Volume
Back LightFont SizeLanguage
0 9
1 5 15
Note: The enabled item is highlighted.
01
[Language]
234567
Automatic
OKBack
89
16151413121110
1718192021
JapaneseNEC English
NEC SpanishNEC FrenchGermanItalian
NEC Portuguese
DutchNorwegianDanishSwedishGreek
Portuguese
FrenchSpanish
English
Polish
TurkishRussian
Romania
Catalan
• T
To cbelowocca
•••
STE
STE
STE
ons.ss ,
ons.ss ,
played. or
71
O CHANGE PASSWORD
hange an existing password, follow the procedure. This password is used for the following
sions.
To lock/unlock the telephone.To delete the directory data.To reset the telephone settings.
P 1: While indicating the current time on LCD,press key to open the Menu screen.
P 2: Select Setting (DT730) / Setting(DT710)Select an item by either of the following operations.• Highlight an item by using , and then press ,
or OK soft key.• Press key (DT730) / key (DT710)
P 3: Select User Setting.
Select an item by either of the following operati• Highlight an item by using , and then pre
or OK soft key.• Press key.
STEP 4: Select Change Password.Select an item by either of the following operati• Highlight an item by using , and then pre
or OK soft key.• Press key.
STEP 5: The Change Password screen is disEnter the old password and then pressSet soft key.
DT730/DT710
Menu
5 2
5 2
12
Tool
[Menu]
3456#0
Call Func.
PresenceFavoriteConfig
Directory
OKBack
History
Setting
1
1
12
Data Backup/Restore
[Setting]
3Download
OKBack
User Setting
4
4
12
[User Setting]
34560
PeripheralsSetting Reset
OKBack
Security
Incoming CallTalk
DisplayChange Password
STE
STE
s suc-follows.
Not be set
the fol-t case,
72
P 6: Enter the new password and then press or Set soft key.
P 7: Enter the new password again and thenpress or OK soft key.
STEP 8: When the password entry completecessfully, the display changes as Press or OK soft key.
e: The initial password is "0000". When changingthe password for the first time, enter "0000" asthe old password.
New Pass
[Change Password]
OKCancelSetBK
1
Old Pass
Retry Pass
[Change Password]
OKCancelSetBK
1Old Pass
Retry Pass
****New Pass
Note: A maximum of 32 digits (0-9, * and #) canas a password.
Note: When the password entry ends in failure,lowing error message is issued. In thapress OK soft key and try again.
[Change Password]
OKCancelSetBK
1Old Pass ****New Pass
Retry Pass****
[Password]
OK
1Complete
[Password]
OK
1Password Error
• T
The off th
STE
STE
STE
ons.ss ,
or
D
73
O RESET TELEPHONE SETTINGS
following explains how to clear the personal datae telephone.
P 1: While indicating the current time on LCD,press key to open the Menu screen.
P 2: Select Setting (DT730) / Setting(DT710)Select an item by either of the following operations.• Highlight an item by using , and then press ,
or OK soft key.• Press key (DT730) / key (DT710)
P 3: Select User Setting.Select an item by either of the following operations.• Highlight an item by using , and then press ,
or OK soft key.• Press key.
STEP 4: Select Setting Reset.Select an item by either of the following operati• Highlight an item by using , and then pre
or OK soft key.• Press key.
STEP 5: Enter the password and then press OK soft key.
T730/DT710
Menu
5 2
5 2
12
Tool
[Menu]
3456#0
Call Func.
PresenceFavoriteConfig
Directory
OKBack
History
Setting
1
1
12
Data Backup/Restore
[Setting]
3Download
OKBack
User Setting
0
0
12
[User Setting]
34560
Peripherals
OKBack
Security
Incoming CallTalk
DisplayChange Password
Setting Reset
STE
74
P 6: Press or OK soft key to clear the person-al data of the telephone.
[Setting Reset]
OKBackBK
1Input a password.
[Setting Reset]
OKBack
Are you sure?
• T
DT73Holdthesenetw
BefoFTP/
STE
STE
ons.ss ,
ons.ss ,
Not
75
O DOWNLOAD A FILE
0 Series user can download files for Music on, Ringer Tone and Directory. When downloading files, the DT Series needs to be connected to the
ork that has FTP (TFTP server).
re starting the download, an IP Address of theTFTP Server must be entered from DT Series.
P 1: Set up the FTP/TFTP server.
<FTP server>Put the downloading file into the designated directory (for Windows IIS, the default is “C:\InetPub\ftproot) of the FTP server.
<TFTP server>Put the downloading file into a desired direc-tory of TFTP server and then specify it as the directory for downloading.
P 2: Select Setting (DT730) / Setting(DT710) on the Menu screen. Select an item by either of the following operations.• Highlight an item by using , and then press ,
or OK soft key.• Press key (DT730) / key (DT710)
STEP 3: Select Download.Select an item by either of the following operati• Highlight an item by using , and then pre
or OK soft key.• Press key.
STEP 4: Select Protocol.Select an item by either of the following operati• Highlight an item by using , and then pre
or OK soft key.• Press key.
e: For details on the FTP/TFTP service, contact theSystem Administrator.
DT730/DT710
5 2
5 2
12
Tool
[Menu]
345670
Call Func.
Presence
Config
Directory
OKBack
History
Setting
2
2
12
Data Backup/Restore
[Setting]
3OKBack
User SettingDownload
3
3
STE
STE
ons.ss ,
ons.ss ,
s, then
76
P 5: Select a protocol used by the server whichstores the download file.Select an item by either of the following operations.• Highlight an item by using , and then press
or OK soft key.• Press or key, and then press or OK soft
key.
P 6: The display goes back to the DownloadMenu screen.
When FTP is selected here, go to the next Step (STEP 7).
When TFTP is selected here, go to the next STEP 15.
STEP 7: Select FTP Settings.Select an item by either of the following operati• Highlight an item by using , and then pre
or OK soft key.• Press key.
STEP 8: Select User ID.Select an item by either of the following operati• Highlight an item by using , and then pre
or OK soft key.• Press key.
STEP 9: Enter a User ID by using digit keypress or OK soft key.
12
[Download Menu]
34 FTP Settings
OKBack
Download FilesDownload Address
Protocol
1 2
12
[Protocol]
OKBack
TFTP
FTP
1
2
4
4
12
[Download Menu]
34
OKBack
Download FilesDownload Address
ProtocolFTP Settings
1
1
12
[FTP Settings]
3OKBack
PasswordFolder
User ID
STE
STE
ettings
ons.ss ,
d file is key.
ettings display
Not
e HOW Basic
e HOW Basic
77
P 10:The display goes back to the FTP Settingsscreen. Select Password.Select an item by either of the following operations.• Highlight an item by using , and then press ,
or OK soft key.• Press key.
P 11:Enter a password by using digit keys, thenpress or OK soft key.
STEP 12:The display goes back to the FTP Sscreen. Select Folder.Select an item by either of the following operati• Highlight an item by using , and then pre
or OK soft key.• Press key.
STEP 13:Enter the directory where the downloastored and then press or OK soft
STEP 14:The display goes back to the FTP Sscreen. Press or Back soft key to
e: For details on character entry method, see HOWTO INPUT CHARACTERS in chapter 4 BasicOperation.
[User ID]
OKBackBK
AInput a user ID.
2
2
12
[FTP Settings]
3OKBack
Folder
User IDPassword
OKBackBK
A[Password]Input a password.
Note: For details on character entry method, seTO INPUT CHARACTERS in chapter 4Operation.
Note: For details on character entry method, seTO INPUT CHARACTERS in chapter 4Operation.
3
3
12
[FTP Settings]
3OKBack
User IDPassword
Folder
OKBackBK
A[Folder]Input a folder name.
STE
STE
K soft
nloadiles.ons.ss ,
and go
and go
nd go
78
the Download Menu screen.
P 15:Select Download Address.Select an item by either of the following operations.• Highlight an item by using , and then press ,
or OK soft key.• Press key.
P 16:Enter an IP address of the FTP/TFTP serverwhich stores the download file. For example,to set the IP address of 10.41.208.205, enter10*41*208*205 [separate with an asterisk(*)].
After entering an IP address, press or Okey.
STEP 17:The display goes back to the DowMenu screen. Select Download FSelect an item by either of the following operati• Highlight an item by using , and then pre
or OK soft key.• Press key.
STEP 18:Select a file to be downloaded.
12
[FTP Settings]
3OKBack
Folder
User IDPassword
2
2
12
[Download Menu]
34 FTP Settings
OKBack
Download Files
ProtocolDownload Address
When downloading a file for Music on Hold
:Select Hold Musicto STEP 20.
When downloading a file for ringer tone
:Select Ring Toneto STEP 19.
When downloading a file for directory
:Select Directory ato STEP 20.
[Download Address]
OKBackBK
1‘*‘For‘.‘
. . .
1
1
12
[Download Menu]
34 FTP Settings
OKBack
Download Files
ProtocolDownload Address
1
2
3
STE
STE
- Wde
e, the
default
Not ize
nds
ize
nds
79
P 19:When Ring Tone is selected at STEP 18,the following Ring Tone screen is displayed. Select either Download1, Download2or Download3.Select an item by either of the following operations.• Highlight an item by using , and then press ,
or OK soft key.• Press - key.
P 20:The default file name will be displayed.
hen downloading a file for Music on Hold, thefault file name is “MOH.wav”.
- When downloading a file for ringer tondefault file name is “Melody1/2/3/.wav”.
- When downloading a file for Directory, the file name is “Directory.csv”.
e: DT710 can select 1 Hold Music only.
12
[Download Files]
3OKBack
Directory
Hold MusicRing Tone
2
1 23
1 3
12
[Ring Tone]
3OKBack
Download3
Download1Download2
File Format Maximum S
PCM µ-law 8kHz/s wav. under 32 seco
File Format Maximum S
PCM µ-law 8kHz/s wav. under 32 seco
[Hold Music]
ExecCancelBK
AInput a file name.
MOH.wav
[Download1/2/3]
ExecCancelBK
AInput a file name.
Melody 1/2/3.wav
[Directory]
ExecCancelBK
AInput a file name.
Directory.csv
STE
STE
STE
ad
Fil
Co
Not
Not
Not
Not
failure,e LCD.
in the
from FTP/
ess of
80
When changing the file name, go to the next step (STEP 21).When not changing the file name, go to STEP 22.
P 21:Press BK soft key once to delete the defaultfile name and then enter a new file name byusing the digit keys.
P 22:Press or Exec soft key to start the down-loading process. While downloading a file,the LCD displays “Downloading...” first andthen “Saving...”.
P 23:After the downloading process is complete,the display changes as follows:
The display goes back to the DownloFiles screen by Exit soft key.
e Name Directory.csv (Fixed)
de Unicode (UTF-8)
e: For details on character entry method, see HOWTO INPUT CHARACTERS in chapter 4 BasicOperation.
e: A maximum of 20 characters ("0-9", "A-Z", "a-z","*", "#", ".", "-" or "_") can be entered as a filename.
e: To delete an entered character, press BK softkey.
e: Be sure not to turn OFF the DT700 Series while"Saving..." is displayed on the LCD.
Note: When the downloading process ends in"Downloading Failed!" is displayed on thCheck to see the following and then retry.
Check Points Actions
Download file is not placed in the specified directory.
Place the download filespecified directory.
A different file name is specified between DT700 Series and FTP/TFTP server.
Set the same file nameboth DT700 Series andTFTP server.
Incorrect IP address of FTP/TFTP server has been entered from the telephone.
Set the proper IP addrFTP/TFTP server.
The power to FTP/TFTP server or network equipment is OFF.
Turn on the power.
LAN cable is disconnected.
Reconnect the cable securely.
Exit
Download Complete!
• T
DT73settinthe sto th
BefoTFTP
STE
STE
ons.ss ,
ons.ss ,
Not
D
81
O BACKUP PERSONAL SETTINGS
0\DT710 Series user can backup personalgs of DT Series to FTP/TFTP server. To back upetting data, the DT Series needs to be connectede network that has FTP (TFTP server).
re starting the backup, an IP Address of the FTP/ Server must be entered from DT Series.
P 1: Set up the FTP/TFTP server.
<FTP server>Confirm the designated directory (for Win-dows IIS, the default is “C:\InetPub\ftproot) for the backed up file.
<TFTP server>Specify a desired destination directory for the backed up file.
P 2: Select Setting (DT730) / Setting(DT710) on the Menu screen. Select an item by either of the following operations.• Highlight an item by using , and then press ,
or OK soft key.• Press key (DT730) / key (DT710)
STEP 3: Select Data Backup/Restore.Select an item by either of the following operati• Highlight an item by using , and then pre
or OK soft key.• Press key.
STEP 4: Select Protocol.Select an item by either of the following operati• Highlight an item by using , and then pre
or OK soft key.• Press key.
e: For details on the FTP/TFTP service, contact theSystem Administrator.
T730/DT710
5 2
5 2
12
Tool
[Menu]
3456#0
Call Func.
PresenceFavoriteConfig
Directory
OKBack
History
Setting
3
3
12
[Setting]
3OKBack
User SettingDownload
Data Backup/Restore
4
4
STE
STE
ons.ss ,
ons.ss ,
s, then
82
P 5: Select a protocol used by the destinationserver.Select an item by either of the following operations.• Highlight an item by using , and then press
or OK soft key.• Press or key, and then press or OK soft
key.
P 6: The display goes back to the Backup/Re-store screen.
When FTP is selected here, go to the next Step (STEP 7).
When TFTP is selected here, go to the next STEP 15.
STEP 7: Select FTP Settings.Select an item by either of the following operati• Highlight an item by using , and then pre
or OK soft key.• Press key.
STEP 8: Select User ID.Select an item by either of the following operati• Highlight an item by using , and then pre
or OK soft key.• Press key.
STEP 9: Enter a User ID by using digit keypress or OK soft key.
12
[Backup/Restore]
34
OKBack
Data BackupData Restore
Server Address
5 FTP SettingsProtocol
1 2
12
[Protocol]
OKBack
TFTP
FTP
1
2
5
5
12
[Backup/Restore]
34
OKBack
Data BackupData Restore
Server Address
5ProtocolFTP Settings
1
1
12
[FTP Settings]
3OKBack
PasswordFolder
User ID
STE
STE
ettings
ons.ss ,
e FTP/K soft
Not
e HOW Basic
e HOW Basic
83
P 10:The display goes back to the FTP Settingsscreen. Select Password.Select an item by either of the following operations.• Highlight an item by using , and then press ,
or OK soft key.• Press key.
P 11:Enter a password by using digit keys, thenpress or OK soft key.
STEP 12:The display goes back to the FTP Sscreen. Select Folder.Select an item by either of the following operati• Highlight an item by using , and then pre
or OK soft key.• Press key.
STEP 13:Enter the destination directory of thTFTP server and then press or Okey.
e: For details on character entry method, see HOWTO INPUT CHARACTERS in chapter 4 BasicOperation.
[User ID]
OKBackBK
AInput a user ID.
2
2
12
[FTP Settings]
3OKBack
Folder
User IDPassword
OKBackBK
A[Password]Input a password.
Note: For details on character entry method, seTO INPUT CHARACTERS in chapter 4Operation.
Note: For details on character entry method, seTO INPUT CHARACTERS in chapter 4Operation.
3
3
12
[FTP Settings]
3OKBack
User IDPassword
Folder
OKBackBK
A[Folder]Input a folder name.
STE
STE
STE
or
up/Re-.ons.ss ,
as fol-
84
P 14:The display goes back to the FTP Settingsscreen. Press or Back soft key to displaythe Backup/Restore screen.
P 15:Select Server Address.Select an item by either of the following operations.• Highlight an item by using , and then press ,
or OK soft key.• Press key.
P 16:Enter an IP address of the destination FTP/TFTP server. For example, to set the IP ad-dress of 10.41.208.205, enter 10*41*208*205[separate with an asterisk (*)].
After entering an IP address, press OK soft key.
STEP 17:The display goes back to the Backstore screen. Select Data BackupSelect an item by either of the following operati• Highlight an item by using , and then pre
or OK soft key.• Press key.
STEP 18:The default file name will be displayedlows:
12
[FTP Settings]
3OKBack
Folder
User IDPassword
3
3
12
[Backup/Restore]
34
OKBack
Data BackupData Restore
5 FTP SettingsProtocolServer Address
[Server Address]
OKBackBK
1‘*‘For‘.‘
. . .
1
1
12
[Backup/Restore]
34
OKBack
Data Restore
5 FTP SettingsProtocolServer Address
Data Backup
STE
STE
/Not
Not
Not
Not
Not
Not
"Upload to see
e ies r.
ress
85
P 19:Press or Exec soft key to start the databackup. While making a backup copy, theLCD displays “Uploading...” first and then“Saving...”.
P 20:After the data backup is complete, the displaychanges as follows:
The display goes back to the BackupRestore screen by Exit soft key.e: Do not change the extension of the backup file.
The setting data of the telephone can only bebacked up as a.tgz file.
e: When changing the default file name, press BKsoft key once to delete the default file name andthen enter a new file name by using the digitskeys.
e: For details on character entry method, see HOWTO INPUT CHARACTERS in chapter 4 BasicOperation.
e: A maximum of 20 characters ("0-9", "A-Z", "a-z","*", "#", ".", "-" or "_") can be entered as a filename.
e: To delete an entered character, press BK softkey.
e: Be sure not to turn OFF the DT700 Series while"Saving..." is displayed on the LCD.
ExecCancelBK
A[Data Backup]Input a folder name.
PersonalData.tgz
Note: When the data backup ends in failure, Failed!" is displayed on the LCD. Checkthe following and then make a retry.
Check Points Actions
A different file name is specified between DT700 Series and FTP/TFTP server.
Set the same file namfrom both DT700 Serand FTP/TFTP serve
Incorrect IP address of FTP/TFTP server has been entered from the telephone.
Set the proper IP addof FTP/TFTP server.
The power to FTP/TFTP server or network equipment is OFF.
Turn on the power.
LAN cable is disconnected.
Reconnect the cable securely.
Exit
Upload Complete!
• T
DT73settinthe tthe n
BefoFTP/
STE
STE
ons.ss ,
ons.ss ,
Not
D
86
O RESTORE PERSONAL SETTINGS
0/DT710 Series user can restore the personalgs of DT Series. To download the backup file to
elephone, the DT Series needs to be connected toetwork that has FTP (TFTP server).
re starting the download, an IP Address of theTFTP Server must be entered from DT Series.
P 1: Set up the FTP/TFTP server.
<FTP server>Put the backup file you want to restore into the designated directory (for Windows IIS, the default is “C:\InetPub\ftproot) of the FTP server.
<TFTP server>Put the backup file you want to restore into a desired directory of TFTP server and then specify it as the directory for downloading.
P 2: Select Setting (DT730) / Setting(DT710) on the Menu screen. Select an item by either of the following operations.• Highlight an item by using , and then press ,
or OK soft key.• Press key (DT730) / key (DT710)
STEP 3: Select Data Backup/Restore.Select an item by either of the following operati• Highlight an item by using , and then pre
or OK soft key.• Press key.
STEP 4: Select Protocol.Select an item by either of the following operati• Highlight an item by using , and then pre
or OK soft key.• Press key.
e: For details on the FTP/TFTP service, contact theSystem Administrator.
T730/DT710
5 2
5 2
12
Tool
[Menu]
3456#0
Call Func.
PresenceFavoriteConfig
Directory
OKBack
History
Setting
3
3
12
[Setting]
3OKBack
User SettingDownload
Data Backup/Restore
4
4
STE
STE
ons.ss ,
ons.ss ,
s, then
87
P 5: Select a protocol used by the server whichstores the backup file.Select an item by either of the following operations.• Highlight an item by using , and then press
or OK soft key.• Press or key, and then press or OK soft
key.
P 6: The display goes back to the Backup/Re-store screen.
When FTP is selected here, go to the next Step (STEP 7).
When TFTP is selected here, go to the next STEP 15.
STEP 7: Select FTP Settings.Select an item by either of the following operati• Highlight an item by using , and then pre
or OK soft key.• Press key.
STEP 8: Select User ID.Select an item by either of the following operati• Highlight an item by using , and then pre
or OK soft key.• Press key.
STEP 9: Enter a User ID by using digit keypress or OK soft key.
12
[Backup/Restore]
34
OKBack
Data BackupData Restore
Server Address
5 FTP SettingsProtocol
1 2
12
[Protocol]
OKBack
TFTP
FTP
1
2
5
5
12
[Backup/Restore]
34
OKBack
Data BackupData Restore
Server Address
5ProtocolFTP Settings
1
1
12
[FTP Settings]
3OKBack
PasswordFolder
User ID
STE
STE
ettings
ons.ss ,
p file is key.
ettings display
Not
e HOW Basic
e HOW Basic
88
P 10:The display goes back to the FTP Settingsscreen. Select Password.Select an item by either of the following operations.• Highlight an item by using , and then press ,
or OK soft key.• Press key.
P 11:Enter a password by using digit keys, thenpress or OK soft key.
STEP 12:The display goes back to the FTP Sscreen. Select Folder.Select an item by either of the following operati• Highlight an item by using , and then pre
or OK soft key.• Press key.
STEP 13:Enter the directory where the backustored and then press or OK soft
STEP 14:The display goes back to the FTP Sscreen. Press or Back soft key to
e: For details on character entry method, see HOWTO INPUT CHARACTERS in chapter 4 BasicOperation.
[User ID]
OKBackBK
AInput a user ID.
2
2
12
[FTP Settings]
3OKBack
Folder
User IDPassword
OKBackBK
A[Password]Input a password.
Note: For details on character entry method, seTO INPUT CHARACTERS in chapter 4Operation.
Note: For details on character entry method, seTO INPUT CHARACTERS in chapter 4Operation.
3
3
12
[FTP Settings]
3OKBack
User IDPassword
Folder
OKBackBK
A[Folder]Input a folder name.
STE
STE
or
up/Re-.
ons.ss ,
as fol-
89
the Backup/Restore screen.
P 15:Select Server Address.Select an item by either of the following operations.• Highlight an item by using , and then press ,
or OK soft key.• Press key.
P 16:Enter an IP address of the FTP/TFTP serverwhich stores the backup file. For example, toset the IP address of 10.41.208.205, enter10*41*208*205 [separate with an asterisk(*)].
After entering an IP address, press OK soft key.
STEP 17:The display goes back to the Backstore screen. Select Data RestoreSelect an item by either of the following operati• Highlight an item by using , and then pre
or OK soft key.• Press key.
STEP 18:The default file name will be displayedlows:
12
[FTP Settings]
3OKBack
Folder
User IDPassword
3
3
12
[Backup/Restore]
34
OKBack
Data BackupData Restore
5 FTP SettingsProtocolServer Address
[Server Address]
OKBackBK
1‘*‘For‘.‘
. . .
2
2
12
[Backup/Restore]
34
OKBack
Data Backup
5 FTP SettingsProtocolServer AddressData Restore
STE
STE
/Not
Not
Not
Not
Not
Not
failure,e LCD. a retry.
file in y.
e ries r.
dress
90
P 19:Press or Exec soft key to start restoringthe backup data to the telephone. Whiledownloading the backup data, the LCD dis-plays “Downloading...” first and then “Sav-ing...”.
P 20:After the downloading process is complete,the display changes as follows:
The display goes back to the BackupRestore screen by Exit soft key.
e: Do not change the extension (.tgz) of the backupfile. If the extension is changed, the file cannot berestored properly.
e: When changing the default file name, press BKsoft key once to delete the default file name andthen enter a new file name by using the digitskeys.
e: For details on character entry method, see HOWTO INPUT CHARACTERS in chapter 4 BasicOperation.
e: A maximum of 20 characters ("0-9", "A-Z", "a-z","*", "#", ".", "-" or "_") can be entered as a filename.
e: To delete an entered character, press BK softkey.
e: Be sure not to turn OFF the DT700 Series while"Saving..." is displayed on the LCD.
ExecCancelBK
A[Data Restore]Input a folder name.
PersonalData.tgz
Note: When the downloading process ends in"Download Failed!" is displayed on thCheck to see the following and then make
Check Points ActionsDownload file is not placed in the specified directory.
Place the download the specified director
A different file name is specified between DT700 Series and FTP/TFTP server.
Set the same file namfrom both DT700 Seand FTP/TFTP serve
Incorrect IP address of FTP/TFTP server has been entered from the telephone.
Set the proper IP adof FTP/TFTP server.
The power to FTP/TFTP server or network equipment is OFF.
Turn on the power.
LAN cable is disconnected.
Reconnect the cablesecurely.
Exit
Download Complete!
SETDT3
• T
The of rin
STE
STE
0 - 12).ng y.
D
91
UP WITH MENU KEY FOR 00 SERIES
O CHANGE RINGER TONE VOLUME
procedure below shows how to change the volumeger tone.
P 1: While indicating the current time on LCD,press key to open the Menu screen.Then, select Settings.Select an item by either of the following operations.• Highlight an item by using , and then press ,
or OK soft key.• Press key.
P 2: Select Ring Volume.Select an item by either of the following operations.• Highlight an item by using , and then press ,
or OK soft key.• Press key.
STEP 3: Ring Volume can be set in 13 levels (Adjust the ringer tone volume by usikey and then press or OK soft ke
T330
Menu
3
3
12
[Menu]
3OKBack
DirectoryCall History
Settings
1
1
Turn the volume up.
Turn the volume down.
12
[Settings]
3
OKBack
Off Hook RingBack Light
45
HeadsetPeripherals
Ring Volume
[ ]
[Ring Volume]
OKBack
• TR
The
STE
STE
, select
ons.ss
r OK soft
92
O ENABLE/DISABLE OFF-HOOK INGING
procedure below shows how to
P 1: While indicating the current time on LCD,press key to open the Menu screen.Then, select Settings.Select an item by either of the following operations.• Highlight an item by using , and then press ,
or OK soft key.• Press key.
P 2: Select Off Hook Ring.Select an item by either of the following operations.• Highlight an item by using , and then press ,
or OK soft key.• Press key.
STEP 3: To disable/enable the off-hook ringingDisable or Enable.
Select an item by either of the following operati• Highlight an item by using , and then pre
or OK soft key.• Press or key, and then press o
key.
DT330
Menu
3
3
12
[Menu]
3OKBack
DirectoryCall History
Settings
2
2
12
[Settings]
3
OKBack
Back Light45
HeadsetPeripherals
Ring VolumeOff Hook Ring
Note: Default setting is 2 Enable.
Note: The enabled item is highlighted.
1 2
1 2
Back OK
[Offhook Ring]
Disable12 Enable
• T
The back
The seco
STE
STE
t.ons.ss
r OK soft
or OK
D
are
are
93
O ENABLE/DISABLE BACKLIGHT
following explains how to enable/disable thelights of LCD and digit keys.
backlights illuminate (for approximately 10nds) when you press any key or lift the handset.
P 1: While indicating the current time on LCD,press key to open the Menu screen.Then, select Settings.Select an item by either of the following operations.• Highlight an item by using , and then press ,
or OK soft key.• Press key.
P 2: Select Back Light.Select an item by either of the following operations.• Highlight an item by using , and then press ,
or OK soft key.• Press key.
STEP 3: Make a selection from the following lisSelect an item by either of the following operati• Highlight an item by using , and then pre
or OK soft key.• Press or key, and then press o
key.
STEP 4: After Making a selection, press soft key.
T330
Menu
3
3
12
[Menu]
3OKBack
DirectoryCall History
Settings
3
3
Menu Item Meaning
1 DisableBacklights of LCD and digit keysdisabled.
2 EnableBacklights of LCD and digit keysenabled.
Note: Default setting is 2 Enable.
Note: The enabled item is highlighted.
12
[Settings]
3
OKBack
45
HeadsetPeripherals
Ring VolumeOff Hook RingBack Light
1 2
Back OK
[Back Light]
12 Enable
Disable
• T
The ringin
STE
STE
set, se-
ons.ss
r OK soft
94
O SET RINGING OF HEADSET
procedure below shows how to enable/disable theg of headset.
P 1: While indicating the current time on LCD,press key to open the Menu screen.Then, select Settings.Select an item by either of the following operations.• Highlight an item by using , and then press ,
or OK soft key.• Press key.
P 2: Select Headset.Select an item by either of the following operations.• Highlight an item by using , and then press ,
or OK soft key.• Press key.
STEP 3: To disable/enable the ringing of headlect Disable or Enable.Select an item by either of the following operati• Highlight an item by using , and then pre
or OK soft key.• Press or key, and then press o
key.
DT330
Menu
3
3
12
[Menu]
3OKBack
DirectoryCall History
Settings
4
4
12
[Settings]
3
OKBack
45 Peripherals
Ring VolumeOff Hook RingBack LightHeadset
Note: Default setting is 1 Disable.
Note: The enabled item is highlighted.
1 2
1 2
Back OK
[Headset]
12 Enable
Disable
4This DT S
•••••••••••••
95
. BASIC OPERATION
chapter describes the following basic operation oferies.
TO LOGINTO LOGOUTTO MAKE AN EXTERNAL CALLTO MAKE AN INTERNAL CALLTO ANSWER AN EXTERNAL CALLTO ANSWER AN INTERNAL CALLMULTILINE APPEARANCETO HOLD A CALLTO PLACE A CALL ON EXCLUSIVE HOLDTO TRANSFER A CALLHOW TO INPUT CHARACTERSSECURITY MODEEMERGENCY CALL
TO
STE
STE(Stat
STE
STE
re Key
of the
termi-
Not
eries.
at the).
96
LOGIN
P 1: When login mode is activated, the telephoneprompts for Login ID and Password.
P 2: Enter login code and press Set soft key.ion number is used as the Login code.)
P 3: Enter the password and press OK Soft key.
P 4: If the login code is accepted, display changesto normal idle status.
TO LOGOUT
STEP 1: Press the preassigned Logout Featuon the terminal.
STEP 2: “LOGOUT?” is displayed on the LCDterminal.
STEP 3: Press the Logout Feature Key on thenal again.
e: This feature is only available for DT700 Series.
DT730/710
Cancel Back Set OKPasswordLogin ID :
:-
Cancel Back Set OKPasswordLogin ID :
:2000
Cancel Back Set OKPasswordLogin ID :
:2000*****
MIC DND >>>7:25 AM MON 12 JUL 2010
Note: This feature is only available for DT700 S
Note: The soft key location is an example.
Note: Logout key is assigned by data settingECP (Enterprise Communication Platform
DT730/710
MIC DND >>>7:25 AM MON 12 JUL 2010
7:25 AM MON 12 JUL 2010L-OUT >>>
LOGOUT?
TO
Whesonawill bare hversamay matio
STE
STE
ation.
ectory
Not
Not
DT7
digits ofd. If thehe firstt sevenor moredminis-
er
de
97
MAKE AN EXTERNAL CALL
n dialed telephone number is registered in Per-l Directory, the corresponding name informatione displayed on LCD of DT730 Series while youearing a ringback tone or are engaged in a con-tion. According to the initial settings, the display
differ from the following examples. For more infor-n, contact the system administrator.
P 1: Lift handset or press key, receive dialtone.
P 2: Dial the Central Office access code, e.g. 9.
STEP 3: Dial desired telephone number.
(while hearing a ringback tone)
STEP 4: Use handset or MIC to start a conversDisplay indicates:(while in a conversation)
• When dialed number is registered in Personal Dir
e: Personal Directory Name Display function isavailable only for DT730 Series.
e: This section describes the Normal Dial Mode.Regarding the other mode, see TO ORIGINATE ACALL USING SELECTIVE DIALING (DYNAMICDIAL PAD, PRESET DIAL) in Chapter 5.
30/710 DT330/310
Speaker
1:25 PM MON 12 JUL 2010MIC DND >>>
31313
Station Number of My Line
1:25 PM MON 12 JUL 2010MIC DND >>>
9
Dialed Code
Note: In the above case, a maximum of eight the number (including “*”) can be displayedialed number exceeds eight digits, “tseven digits of the number + *” or “the lasdigits of the number + *” are displayed. Finformation, please contact the system atrator.
1:25 PM MON 12 JUL 20109XXXXXXXXX
MIC >>>
Dialed Code + Numb
9XXXXXX*00:05
Elapsed Time
TOM JONESMIC DND >>>
Dialed CoName Informationregistered in Personal Directory + Number
• Wto
Not
98
hen dialed number is not registered in Personal Direc-ry
e: My Line is an actual line that is directly associ-ated with station number of the telephone. Youcan make/answer a call via this line. Usually, Myline is seized automatically only by lifting thehandset or pressing the Speaker key.
00:05
Elapsed Time
MIC DND >>>
Dialed Code
9XXXXXXXXX
+ Number
TO
WheDirecdispling aAccofromconta
STE
STE
(w• W
re
ersonal
nversa-
onal Di-
ersonal
Not
Not
DT7 mber
r
ber
99
MAKE AN INTERNAL CALL
n dialed station number is registered in Personaltory, the corresponding name information will beayed on LCD of DT730 Series while you are hear- ringback tone or are engaged in a conversation.rding to the initial settings, the display may differ the following examples. For more information,ct the system administrator.
P 1: Lift handset or press key, receive dialtone.
P 2: Dial desired station number. Display indi-cates digits dialed.
hile hearing a ringback tone)hen dialed station number is registered in Personal Di-ctory
• When dialed station number is not registered in PDirectory
STEP 3: Use the handset or MIC to start a cotion.
(while in a conversation)
• When dialed station number is registered in Persrectory
• When dialed station number is not registered in PDirectory
e: Personal Directory Name Display function isavailable only for DT730 Series.
e: This section describes the Normal Dial Mode.About the other mode, see TO ORIGINATE ACALL USING SELECTIVE DIALING (DYNAMICDIAL PAD, PRESET DIAL) in chapter 5.
30/710 DT330/310
Speaker
1:25 PM MON 12 JUL 201031313
Station Number of My Line
Blink
MIC DND >>>
31314
Dialed Station Nu
MIC >>>MARY HARRIS
Name Information registeredin Personal Directory
1:25 PM MON 12 JUL 201031314
Dialed Station Numbe
MIC >>>
31314
Dialed Station Num
Name Informationregistered in Personal Directory
MIC DND >>>MARY HARRIS
Not
100
e: My Line is an actual line that is directly associ-ated with station number of the telephone. Youcan make/answer a call via this line. Usually, Myline is seized automatically only by lifting thehandset or pressing the Speaker key.
1:25 PM MON 12 JUL 201031314
Dialed Station Number
MIC DND >>>
TO
WhePerstion you convplay infor
STE
• Wso
• WP
• W
ropriate
d in Per-
tered in
Not
DT7 er
ber
101
ANSWER AN EXTERNAL CALL
n calling party telephone number is registered inonal Directory, the corresponding name informa-will be displayed on LCD of DT730 Series whileare hearing a ringing tone or are engaged in aersation. According to the initial settings, the dis-may differ from the above example. For more
mation, contact the system administrator.
P 1: You hear the ringing tone. Call indicator flash-es red while hearing ring tone.
hen calling party telephone number is registered in Per-nal Directory
hen calling party telephone number is not registered inersonal Directory
hen caller ID is not received
STEP 2: Press key or touch the appLine Key.
STEP 3: Lift the handset to answer the call.
(while in a conversation)• When calling party telephone number is registere
sonal Directory
• When calling party telephone number is not regisPersonal Directory
e: Personal Directory Name Display function isavailable only for DT730 Series.
30/710 DT330/310
TOM JONES
Name Information registeredin Personal Directory
MIC DND >>>
01234567MIC DND >>>
Calling Party Telephone Number
1:25 PM MON 12 JUL 2010DDD 3
Trunk TrunkNumbType
MIC DND >>>
Answer
TOM JONES
Name Information
Personal Directory
MIC DND >>>
registered in
00:05
ElapsedTime
Calling Party
MIC DND >>>
Telephone Num
00:05
ElapsedTime
01234567
• W
Not
102
hen caller ID is not received
e: When an incoming call is terminated to My Lineof the telephone, you can usually answer the callonly by lifting the handset or pressing theSpeaker Key.
1:25 PM MON 12 JUL 2010DDD 3
Trunk Trunk NumberType
MIC DND >>>
00:05
ElapsedTime
TOThe inter
WheDirecdispling aAccofromtact t
STE
• Wre
• WD
ropriate
onal Di-
ersonal
Not
y Line the calling the
tation
tion
103
ANSWER AN INTERNAL CALL following procedure explains how to answer annal call routed to My Line of the telephone.
n calling station number is registered in Personaltory, the corresponding name information will beayed on LCD of DT730 Series while you are hear- ringing tone or are engaged in a conversation.rding to the initial settings, the display may differ the above example. For more information, con-he system administrator.
P 1: You hear the ringing tone. Call indicator flash-es red while hearing ring tone.
hen calling station number is registered in Personal Di-ctory
hen calling station number is not registered in Personalirectory
STEP 2: Press key or touch the appLine Key.
STEP 3: Lift the handset to answer the call.
(while in a conversation)• When calling station number is registered in Pers
rectory
• When calling station number is not registered in PDirectory
e: Personal Directory Name Display function isavailable only for DT730 Series.
Name Information registeredin Personal Directory
MIC >>>MARY HARRIS
31314
Calling Station Number
Calling Station Number
1:25 PM MON 12 JUL 201031314
MIC >>>
Note: When an incoming call is terminated to Mof the telephone, you can usually answeronly by lifting the handset or pressSpeaker Key.
Answer
Name Information
Personal Directory registered in
31314
Calling SNumber
MIC >>>MARY HARRIS
Calling StaNumber
1:25 PM MON 12 JUL 201031314
MIC >>>
MU
To OSTE
STE
STE
To A
STE
STE
STE
hes.
rse.
Recall
nd ringcall on
on yourws as aflashing LED on
DT7
tations,
retrieve
0/310
104
LTILINE APPEARANCE
riginate a CallP 1: Press the MULTILINE APPEARANCE fea-
ture key.
P 2: Lift handset or press key. Dial theCentral Office access code (i.e.9 (US), 0(Aust)).
P 3: Dial the desired number.
nswer a Call
P 1: Press the MULTILINE APPEARANCE fea-ture key (ringing and flashing LED alert userto incoming call).
P 2: Lift handset or press key.
P 3: Speak with incoming party.
TO HOLD A CALL
STEP 1: Press key. Held line wink flas
To RetrieveSTEP 1: Lift handset or press key.
STEP 2: Press held line. Use handset to conve
If unanswered
STEP 1: After preprogrammed time, Automaticis initiated.
STEP 2: Visual and audible signal (rapid flash aburst) is sent to station that placed hold.
Note: Hold shows as a flashing green LED phone. The same line on other phones shoflashing red LED. Recall shows as a green LED on your phone and flashing redother phones with the same line.
30/710 DT330/310
Speaker
Speaker
Note: If held line appears on other DT Series sthe associated LED flashes red slowly.
Note: Any station with this line appearance can the call.
DT730/710 DT33
HOLD
MIC >>>
Held Station Number
2001HOLD1:25 PM MON 12 JUL 2010
Speaker
TOHO
STE
To RSTE
STE
If unSTE
STE
ted dial
ang up
Not
Not
e from showse. Theolid red
r
105
PLACE A CALL ON EXCLUSIVE LD
P 1: Press key twice. Line appearance in-dicates interrupted wink.
etrieveP 1: Lift handset or press key.
P 2: Press held line. Use handset to converse.
answeredP 1: After preprogrammed time, Automatic Recall
is initiated.
P 2: Visual and audible signal (rapid flash and ringburst) is sent to station which placed call onExclusive Hold. Recall shows as a flashinggreen LED on your phone, and solid red onother phones with same line.
TO TRANSFER A CALL
STEP 1: After conversing, ask party to hold.
STEP 2: Press key. Receive interruptone.
STEP 3: Dial destination station’s extension, hor wait for answer.
e: If held line appears on other DT Series stations,LED remains steadily lit red.
e: Only the DT Series that set Exclusive Hold optioncan retrieve the call.
DT730/710 DT330/310
HOLD
MIC >>>
Held Station Number
2001E_HOLD1:25 PM MON 12 JUL 2010
Speaker
Note: Exclusive Hold excludes any other phonpicking up your held call. Exclusive Holdas a flashing green LED on your phonsame line on other phones appears as a sLED.
DT730/710 DT330/310
Transfer
MIC >>>1:25 PM MON 12 JUL 2010
TRANSFER
MIC >>>1:25 PM MON 12 JUL 2010
TRANSFER 2001
or trunk numbeTransferred station
STE
106
P 4: If transferring party hangs up, that station’snumber appears in the center of recipient’sdisplay.
MIC >>>1:25 PM MON 12 JUL 2010
TRANSFER 2000 DDD 3
Transferring station
HOThis
• CW habeticc ged byp
T
K
107
W TO INPUT CHARACTERS section explains how to enter characters on the text input screen such as Name or User ID, etc.
haracter Entry Modehen entering characters from the telephone set, the following three modes are available: uppercase alp
haracter, lowercase alphabetic character and numeric character. The character entry mode can be chanressing key (alphabetic/numeric) or from the Sub Menu screen (uppercase/lowercase).
he enabled entry mode is indicated in the top portion of the LCD screen (DT730 only).
DT730
*
Uppercase Alphabetic Lowercase Alphabetic
Numeric Character Mode
By pressing “*” key
Indicates the enabled character mode. (DT730 only.)
Input a name.[Name]
OKBackOptionBK
AAInput a name.[Name]
OBackOptionBK
Aa
Input a name.[Name]
OKBackOptionBK
A1
12
Word-width
SubMenu
345678
PasteSpace
Change-word
OKCancel
Cut
DeleteCopy
ReturnOverwrite/Insert
910
Word-case
Character ModeCharacter ModeSelect “2 Word-case” to switchbetween uppercase and lowercase.
or from Sub Menu (select “1 Change-word”)
T played.A
108
o display the Sub Menu screen, press key or Option Soft Key while the text input screen is dislso, the following operations are available from the Sub Menu screen.
Sub Menu Items Descriptions
Change-word Change character entry mode between uppercase alphabetic, lower-case alphabetic and numeric character.
Word-case Switch between uppercase and lowercase.Word-width Not used.Delete Delete a single character.Copy Copy the specified characters.Cut Cut the specified characters.Paste Paste the specified characters.Space Enter a space.Return Start a new line.Overwrite/Insert Write over existing characters.
Menu
12
Word-width
SubMenu
345678
PasteSpace
Change-word
OKCancel
Cut
DeleteCopy
ReturnOverwrite/Insert
910
Word-case
• C
<
109
haracter Code List
Character Code For English (1/2)>
DIGIT KEY
CASE SHIFT 1st 2nd 3rd 4th 5th 6th 7th 8th 9th 10th 11th 12th 13th
. , \ 1 ? ! “Note
@ : ;
A B C 2
a b c 2
D E F 3
d e f 3
G H I 4
g h i 4
J K L 5
j k l 5
M N O 6
m n o 6
P Q R S 7
p q r s 7
T U V 8
t u v 8
W X Y Z 9
w x y z 9
[SP] 0
Note: Not available from Firmware version 3.0.0.0 and later
1 A
a
2 Aa
3A
a
4A
a
5A
a
6 A
a
7 A
a
8 Aa
9Aa
0 Aa
<C
110
haracter Code For English (2/2)>
1st 2nd 3rd 4th 5th 6th 7th 8th 9th 10th
Note1
* # . / : ~ ! @ $ %
11th 12th 13th 14th 15th 16th 17th 18th 19th 20th
^ & ( ) ' ? “Note2
_ + -
21th 22th 23th 24th 25th 26th 27th 28th 29th 30th
= [ ] { } < > , ; \
Note1
Used as a case shift key. Shifts the characters between alphabetic and numeric.
Note1: and key is the same for Russian, Turkish and other Languages.
Note2: Not available from Firmware version 3.0.0.0 and later
#
A
a
A
a
A
a
*
# *
<
DK 5th
¡
N
111
Character Code For Russian>
IGIT EY
CASE SHIFT 1st 2nd 3rd 4th 5th 6th 7th 8th 9th 10th 11th 12th 13th 14th 1
. , : ! ? + - % & / ( ) = ¿
A Б В Г
а б в г
Д Е Ё Ж З
д е ё ж з
И Й К Л
и й к л
М Н О П
м н о п
Р С Т У
р с т у
Ф Х Ц Ч
ф х ц ч
Ш Щ Ъ Ы Ь
ш щ ъ ы ь
Э Ю Я
э ю я
[SP]
ote: and key is the same for English. Refer to the <Character Code For English (2/2)>.
1A
a
2 Aa
3A
a
4A
a
5 A
a
6A
a
7A
a
8 Aa
9Aa
0 Aa
# *
<
DK 5th
¡
N
112
Character Code For Turkish>
IGIT EY
CASE SHIFT 1st 2nd 3rd 4th 5th 6th 7th 8th 9th 10th 11th 12th 13th 14th 1
. , : ! ? + - % & / ( ) = ¿
A B C Ça b c çD E Fd e f
G H I
g h I
J K Lj k l
M N O Öm n o öP R Sp r sT U Ü Vt u ü vY Zy z
[SP]
ote: and key is the same for English. Refer to the <Character Code For English (2/2)>.
1A
a
2 Aa
3 A
a
4A Ğ İ
a ğ i
5 A
a
6A
a
7A Ş
a Ş
8 Aa
9 Aa
0 Aa
# *
<
DK 5th
¡
N
113
Character Code For Other Languages>
IGIT EY
CASE SHIFT 1st 2nd 3rd 4th 5th 6th 7th 8th 9th 10th 11th 12th 13th 14th 1
. , : ! ? + - % & / ( ) = ¿
A B C À Á Â Ã Ä Å Æ Ça b c à á â ã ä å æ çD E F È É Ê Ëd e f è é ê ëG H I Ì Í Î Ïg h i ì í î ïJ K Lj k l
M N O Ñ Ò Ó Ô Õ Ö Œ Øm n o ñ ò ó ô õ ö œ øP Q R S ßp q r s ßT U V Ù Ú Û Üt u v ù ú û üW X Y Zw x y z
[SP]
ote: and key is the same for English. Refer to the <Character Code For English (2/2)>.
1A
a
2 Aa
3A
a
4 A
a
5A
a
6A
a
7A
a
8 Aa
9 Aa
0 Aa
# *
<
DK 5th
\
N
114
Number Code>
IGIT EY
CASE SHIFT 1st 2nd 3rd 4th 5th 6th 7th 8th 9th 10th 11th 12th 13th 14th 1
1
2
3
4
5
6
7
8
9
0
* # . @ / ( ) , - _ : ‘ ~ &
Used as a case shift key. Shifts the characters between alphabetic and numeric.
ote: When entering password, “0-9”, “*” and “#” are available.“#” is entered by pressing key.
“*” is entered by pressing key.
1 1
2 1
3 1
4 1
5 1
6 1
7 1
8 1
9 1
0 1
# 1
* 1
#
*
• CAl
STE
STE
enu to
115
haracter Entry Methods an example of character entry method, the fol-
owing shows how to enter “Ken Kobus”.
P 1: Press key twice to enter “K”.
P 2: Press key or Option soft key to displaySub Menu screen, and then select Word-case to switch the text input mode from up-percase to lowercase.
STEP 3: Press or OK soft key on the Sub Mgo back to text input screen.
STEP 4: Enter “en” by using digit keys.
Press key twice to enter “e”.Press key twice to enter “n“.
STEP 5: Press key once to enter a space.
5
Input a name.[Name]
OKBackOptionBK
A
K
Menu
2
12
Word-width
SubMenu
345678
PasteSpace
Change-word
OKCancel
Cut
DeleteCopy
ReturnOverwrite/Insert
910
Word-case
Input a name.[Name]
OKBackOptionBK
a
K
36
Input a name.[Name]
OKBackOptionBK
a
Ken
0
Input a name.[Name]
OKBackOptionBK
a
Ken
STE
STE
displayWord-m low-
116
P 6: Press key or Option soft key to displaySubMenu screen, and then select Word-case to switch the text input mode from low-ercase to uppercase.
P 7: Press or OK soft key on the Sub Menu togo back to text input screen.
STEP 8: Press key twice to enter “K”.
STEP 9: Press key or Option soft key toSubMenu screen, and then select case to switch the text input mode froercase to uppercase.
Menu
2
12
Word-width
SubMenu
345678
PasteSpace
Change-word
OKCancel
Cut
DeleteCopy
ReturnOverwrite/Insert
910
Word-case
Input a name.[Name]
OKBackOptionBK
A
Ken
5
Input a name.[Name]
OKBackOptionBK
A
Ken K
Menu
2
12
Word-width
SubMenu
345678
PasteSpace
Change-word
OKCancel
Cut
DeleteCopy
ReturnOverwrite/Insert
910
Word-case
STE
STE
STE
117
P 10:Press or OK soft key on the Sub Menu togo back to text input screen.
P 11:Enter “obus” by using digit keys.Press key three times to enter “o”.Press key twice to enter “b“.Press key twice to enter “u”.Press key four times to enter “s“.
P 12:Press or OK soft key.
Input a name.[Name]
OKBackOptionBK
a
Ken K
6287
Input a name.[Name]
OKBackOptionBK
a
Ken Kobus
• T
STE
STE
STE
ters. In
118
o Overwrite Characters
P 1: Place the cursor at the left of the charactersto be overwritten.
P 2: Press key or Option soft key.
P 3: On the following Sub Menu screen, selectOverwrite/Insert and then press , or OK soft key.
STEP 4: Enter new words over existing characthis example, “F” is entered.
Input a name.[Name]
OKBackOptionBK
A
ABCDE
Menu
10
12
Word-width
SubMenu
345678
PasteSpace
Change-word
OKCancel
Cut
DeleteCopy
Return910
Word-case
Overwrite/Insert
Input a name.[Name]
OKBackOptionBK
A
ABFDE
• T
STE
STE
t of thed then
e targetoft key.
u wantn press
119
o Copy and Paste Characters
P 1: While characters which you want to copy aredisplayed, press key or Option softkey.
P 2: On the Sub Menu screen, press or OKsoft key while Copy is highlighted, orpress key.
STEP 3: Place the cursor at the starting pointarget characters by using anpress Start soft key.
STEP 4: Place the cursor at the end point of thcharacters and then press End s
STEP 5: Place the cursor at position where yoto paste the copied characters and the
key or Option soft key.
Menu
Input a name.[Name]
BackBK
A
ABCDEOption OK
55
12
Word-width
SubMenu
345678
PasteSpace
Change-word
OKCancel
Cut
Delete
Return910
Word-case
Overwrite/Insert
Copy
Input a name.[Copy]
BackStart
A
ABCDE
Input a name.[Copy]
BackEnd
A
ABCDE
Menu
Input a name.[Name]
BackBK
A
ABCDEOption OK
STE
STE
120
P 6: On the Sub Menu screen, select Pasteand then press , or OK soft key. (orpress key.)
P 7: The copied characters “CD” are inserted asfollows:
7
7
12
Word-width
SubMenu
345678 Space
Change-word
OKCancel
Cut
Delete
Return910
Word-case
Overwrite/Insert
Copy
Paste
Input a name.[Name]
BackBK
A
CDABCDEOption OK
SECDT73inforlocke
ou cansetting,erminal
s. TheD.
00 Se-
Not
Not
ailable mode.ecurity called party.
any the the
121
URITY MODE 0 Series has the Security key which prevents
mation leakage from terminal. While the terminal isd, Security Lamp lights up.
• TO LOCK THE TELEPHONE
Before placing DT700 Series in Security mode, yset a password. For details on the password see TO CHANGE PASSWORD in chapter 3 TSetup.
STEP 1: Press Security key on DT730 Seriefollowing message is displayed on LC
STEP 2: Press or OK soft key to place DT7ries in Security mode.
e: When the system administrator invalidates the security mode, this function cannot be used. For details of the security mode, con-tact the system administrator.
e: While the telephone is locked, keybecomes disabled. Also, any features pro-vided by the telephony server, such as callorigination or call answering, cannot be per-formed.(The Incoming call cannot be pickedup though "Ringing" or "Voice call" are pos-sible.)It is necessary to release the securitymode to respond.
DT730
Security Lamp lights up.
Security lock will be released.Please input a password.
Press Security Key.
BK Cancel OK
Menu
Note: To make a call of VOICE CALL is avtoward a called party in the SecurityWhen a called party activates the Smode with leaving its MIC to ON, theparty can converse with a callingthough terminal operation is restricted
Note: Even when the telephone is reset for reason (such as power-off, etc.) whiletelephone is placed in security mode,lock is not released.
Security Lock?
OKCancel
STE
• T
STE
•
•
STE
the fol-t case,
sswordessage
he tele- will be, make
122
P 3: When DT730 Series is placed in Securitymode, Security Lamp lights red and thescreen saver will be activated.
O UNLOCK THE TELEPHONE
P 1: Display the Password Entry screen by eitherof the following operations.
Press any key while the screen saver isactivated.Press Security key while the screen saver isactivated.
P 2: Enter the password and then press orOK soft key. Security Lamp is extinguishedand Security Mode is canceled.
Security Lock
Security lock will be released.
OKCancel
Please input a password.
BK
Note: When the password entry ends in failure,lowing error message is issued. In tha
press or OK soft key and then retry.
Note: After a third attempt (if incorrect paentered three times), the following error m
is issued. Press or OK soft key. Tphone locks up, and any key operationdisabled for 10 minutes. After 10 minutesa retry.
Password Error.
OKCancel
Retry?
Incorrect security code
OK
password entered.
EMYou telepSecutelep
STE
STE
andset.ecurity
Not
Not
Not
Not
rminedhan thedialed,
ew sec-rgency
123
ERGENCY CALL can make a call to a predetermined emergencyhone number while the telephone is locked (inrity mode). This function is available on thehone with Security key.
P 1: Lift the handset while the telephone is locked(the screen saver is activated).
P 2: Dial an emergency telephone number bypressing digit keys(0-9, *, #).
STEP 3: After a conversation, replace the hThe LCD turns to time display. (Smode is released.)
e: You can make an emergency call to only the pre-determined number. For details on the setting ofthe emergency number, contact the systemadministrator.
e: Emergency call cannot be made with Speakerkey.
e: When pressing Unlock soft key, the telephoneprompts for the Security mode cancellation pass-word.
e: Emergency telephone number needs to be set inadvance. For the setting of the emergency tele-phone numbers, contact the system administra-tor.
DT730
Dial Emergency Number Only
Unlock
Note: You can make a call to only the predetenumber. When telephone numbers other tpredetermined emergency number are the following message appears (after a fonds, the display goes back to "Dial EmeNumber Only” screen).
Invalid Dial.911
124
This page is for your notes.
5TOSEL(DYDIA
Dyn
STE
STE
STE
Pre
STE
top of
t hand-
Not
the fol-
t.
125
. FEATURE OPERATION
ORIGINATE A CALL USING ECTIVE DIALINGNAMIC DIAL PAD, PRESET L)
amic Dial Pad
P 1: Enter desired telephone number (Digit Keys0-9, *, and #).
P 2: LED on key lights and hear key touchtone.
P 3: The dialed number appears on the top ofLCD.
set Dial
P 1: Enter desired telephone number (Digit Keys0-9, *, and #).
STEP 2: The dialed number appears on theLCD.
STEP 3: Lift handset or press key.or
STEP 3: Press the originating Line Key and lifset.
e: Pressing the Speaker Key or going off-hook is notnecessary.
DT730/710 DT330/310
Speaker
2000
MIC >>>1:25 PM MON 12 JUL 2010
DT730/710 DT330
Note: Originating call operation is cancelled by lowing Soft Key operation;- Press Exit key or Cancel Key.- Press Clear Key and cancel by one digi
Note: This feature cannot use on ITL-2E-1.
2000 Clr Cnl
Input Dial Number
Speaker
TO CA(ON
STE
To P(AvaCalli
STE
STE
STE
STE
To VSTE
STE
DT7
feature. (! dis-
key aslays on
ey after.)
access:ed as as code.system
on withan pro-ension.
126
ORIGINATE A CALL USING SPEED LLINGE-TOUCH SPEED CALLING KEYS)
P 1: Press the desired One-Touch Speed Call-ing key, or press key and One-TouchSpeed Calling key.
rogramilable only on DT Series with One-Touch Speed ng key.)
P 2: Press key.
P 3: Press desired One-Touch Speed Callingkey.
P 4: Enter desired telephone number or featureaccess code on the keypad.Display indicates the digits dialed.
P 5: Press key again to save the number.
erifyP 1: Press key.
P 2: Press desired One-Touch Speed Callingkey.
STEP 3: Display indicates digits programmed.
30/710 DT330/310
Speaker
Feature
Feature
SPEED SET1:25 PM MON 12 JUL 2010 MIC DND >>>
Feature
Note: To program a hook switch for transfer or activation, press key as first digitplays on LCD.)
Note: To program a pause, press the any digit other than the first digit. (– dispLCD.)
Note: To program a Voice Call, press kdialing station number. (V displays on LCD
Note: One-Touch Speed Calling key for feature One-Touch Speed Calling key may be usfeature key by storing the feature accesThe features may be programmed on a basis by the Telephony Server Admin.Access codes may be stored in conjunctitelephone numbers. For example, you cgram one button to transfer to a certain ext
Recall
Recall
Transfer
LCDSTE
WheSpeeuppechar
The One
E)
DIGITKEY
CH
AR
AC
TER
#
#
s which
127
Indication of 8LD DisplayP 1: Press the desired One-Touch Speed Call-
ing key and originate a call.Registered name will be displayed as follows.For the key to which no name information isregistered, the character “SPD” will be dis-played.
n registering Name Information of One-touch d Calling, you can use uppercase alphabetic, rcase European or lowercase European
acters.
following tables show available characters for -Touch Speed Calling keys.
ALPHABETIC CHARACTER (UPPERCASE)
EUROPEAN CHARACTER (UPPERCAS
1 2 3 4 5 6 7 8 9 0 #
1 A D G J M P T W 0 #B E H K N Q U X @ &C F I L O R V Y . (
a d g j m S t Z , )
b e h k n p u w ’ [
c f i l o q v x : ]
2 3 4 5 6 r 8 y ; !
s z - ?
7 9 /
DIGIT KEY 1 2 3 4 5 6 7 8 9 0
CH
AR
AC
TER
. A D G J M P T W 0, B E H K N Q U X: C F I L O R V Y! À È Ì 5 Ñ S Ù Z
? Á É Í Ò Ú 9
- Â Ê Î Ó 7 Û+ Ã Ë Ï Ô Ü% Ä 3 4 Õ 8
& Å Ö/ Æ Œ( Ç Ø) 2 6=
¿¡1
Note: The shaded area indicates the charactercannot be entered.
DIGITKEY
CH
AR
AC
TER
Not
128
EUROPEAN CHARACTER (LOWERCASE) 1 2 3 4 5 6 7 8 9 0 #
. a d g j m p t w 0 #, b e h k n q u x: c f i l o r v y! à è ì 5 ñ s ù z
? á é í ò ú 9
- â ê î ó 7 û+ ã ë ï ô ü% ä 3 4 õ 8
& å ö/ æ œ( ç ø) 2 6=
¿¡1
e: The shaded area indicates the characters whichcannot be entered.
TO SPE
(Ava
STE
STE
STE
STE
8LD
in To (One-
EED
er.
Key
Callingred dig-
Not
Not
DT7
129
REGISTER NAME ON ONE-TOUCH ED CALLING KEY
ilable for 8LD Display terminal.)
P 1: Press NAME.
P 2: Press desired One-Touch Speed Callingkey.
P 3: Enter desired name on the keypad.Display indicates the name entered.
P 4: Press SET to save the name.
To Register Speed Calling Number OnDisplay
STEP 1: Follow the procedure of To programOriginate a Call Using Speed CallingTouch Speed Calling Keys).
TO ORIGINATE A CALL USING SPCALLING - STATION/GROUP
STEP 1: Press (Redial).
STEP 2: Press the desired speed calling numb
TO ORIGINATE A CALL USING SPEED CALLING - SYSTEM
To Program Speed Calling – System (On One-Touch Speed Calling Key)
STEP 1: Press key.
STEP 2: Press desired One-Touch Speed key. The LCD displays previously stoits.
e: To delete the entry, press DEL or BK key anddelete each one character.
e: To delete the whole setting, press CLEAR keyand back to idle status.
30 DT330
Push Speed Calling Key
NAME(*) >>>1:25 PM MON 12 JUL 2010
^ NEC BNET
SET CANCEL CLEAR >>>
NAME >>>1:25 PM MON 12 JUL 2010
DT730/710 DT330/310
XXXXXXLNR[ ]/SPD[_ _] –X*
MIC PICK FDA >>>
DT730/710 DT330/310
Feature
STE
STE
To OKey
STE
STE
To O(Onlywith
STE
STE
130
P 3: Dial the “Speed Calling – System” accesscode and the abbreviated call code.
P 4: Press key again.
perate From Speed Calling – System
P 1: Press the “Speed Calling – System” key.
P 2: If the DT Series does not have the “SpeedCalling – System” key, dial the “Speed Calling– System” access code, then the abbreviatedcall code.
perate From Directory Key DT710 Series and DT310 Series are equipped
Directory key.)
P 1: Press key.
P 2: Dial the abbreviated call code (maximum of 4digits).
Feature
SPEED SET1:25 PM MON 12 JUL 2010
XXXX1:25 PM MON 12 JUL 2010
Directory
XXXX1:25 PM MON 12 JUL 2010
ACTo ESTE
STE
STE
STE
To EAutSTE
STE
STE
STE
ive dial
service
10 dig-
ive dial
service
igits).
r.
Not
Not
e up to
f digitson and
131
COUNT CODE
nterP 1: Lift handset or press key, receive dial
tone.
P 2: Enter feature access code, receive serviceset tone.
P 3: Enter “Account Code” (up to 10 digits).
P 4: Receive dial tone and dial desired number.
nter Account Code After horization CodeP 1: Lift handset or press key, receive dial
tone.
P 2: Enter feature access code for “AuthorizationCode”, receive service set tone.
P 3: Enter “Authorization Code”, receive secondservice set tone.
P 4: Enter “Account Code”, receive dial tone, anddial desired number.
FORCED ACCOUNT CODE
STEP 1: Lift handset or press key, recetone.
STEP 2: Enter feature access code, receive set tone.
STEP 3: Enter “Forced Account Code” (up to its), receive dial tone.
AUTHORIZATION CODE
To Enter Without Account CodeSTEP 1: Lift handset or press key, rece
tone.
STEP 2: Enter feature access code, receive set tone.
STEP 3: Enter “Authorization Code” (up to 10 d
STEP 4: Receive dial tone, dial desired numbe
- Or -
STEP 4: Lift handset, receive dial tone.
e: For North America, Account Codes can be up to24 digits.
e: Authorization and Account Codes may be up to20 digits combined (or 34 digits combined).
DT730/710 DT330/310
Speaker
Speaker
Note: For North America, Account Codes can b24 digits.
Note: For North America, the total number owhich can be entered for AuthorizatiAccount Codes is 34 digits.
DT730/710 DT330/310Speaker
DT730/710 DT330/310
Speaker
STE
STE
STE
To EServprog
VOSTE
STE
STE
STE
oft Key
d party.
Not
Not
a One-g One-tension,s if pro-ave by
Call ises:
tation is
132
P 5: Dial desired number.
P 6: If an “Authorization Code” is required, callerhears special dial tone.
P 7: Enter “Authorization Code”, or call will be de-nied.
nter With Account Code (see above)ice set tone is optional depending upon system ramming.
ICE CALL
P 1: Lift handset.
P 2: Dial desired station number.
P 3: Press Voice.
P 4: Speak to called party.
Using Soft KeySTEP 1: Lift handset.
STEP 2: Dial desired station number; VOICE Sappears while station is ringing.
STEP 3: Press VOICE Soft Key. Speak to calle
e: This option is available only if system is pro-grammed with Least Cost Routing.
e: If a 4-, 8-, 16- or 32-button display terminal isused, the display indicates all of the digits dialed.
DT730/710 DT330/310
VOICE 20001:25 PM MON 12 JUL 2010
Note: A Voice Call may be programmed on Touch Speed Calling key by pressinTouch Speed Calling key, dialing the exand pressing the key. (V displaygramming on an DT Series with LCD. Spressing One-Touch Speed Calling key.)
Note: If called party is on their line when a Voiceattempted, calling station's display indicat
Note: A voice call is restricted if called party's snot a DT Series. Display indicates:
2000
MIC >>>VOICE1:25 PM MON 12 JUL 2010
Transfer
VOICE BUSY1:25 PM MON 12 JUL 2010
VOICE REST1:25 PM MON 12 JUL 2010
TOFRESTE
STE
STE
AU
To ISTE
STE
STE
coming
key.
tercom placingy).
Call
r press
Not
DT7
ker
133
ANSWER A VOICE CALL HANDS E
P 1: Receive incoming Voice Call.
P 2: Press the MIC Soft Key or key. LEDlights.
P 3: Respond hands-free.
TOMATIC INTERCOM
nitiateP 1: Lift handset or press key.
P 2: Press the AICM key.
P 3: Hear ringback tone.
To AnswerSTEP 1: AICM key flashes red indicating an in
intercom call.
STEP 2: Press AICM, lift handset or press LED lights solid green.
STEP 3: If called station is engaged in a non-incall, the station may press AICM afteroriginal caller on hold (with ke
To Bridge Into An Automatic Intercom
STEP 1: Press the AICM key, lift handset o key.
e: If privacy is required, lift handset.
DT730/710 DT330/310
Mic
Calling station
VOICE 20011:25 PM MON 12 JUL 2010
30/710 DT330/310
Speaker
Called party
ICM 21:25 PM MON 12 JUL 2010
Note: Bridging is an optional feature.
Overriding party
ICM 11:25 PM MON 12 JUL 2010
Spea
HOLD
Speaker
Overriding party
OVERRIDE 11:25 PM MON 12 JUL 2010
STE
MA
To ISTE
STE
To ASTE
STE
STE
tercom placingy).
ll
key.
d.
DT7
station unnec-
buttonate sig- for the
ker
134
P 2: A three-party conference is established.
NUAL INTERCOM
nitiateP 1: Press MICM, lift handset or press key,
ringback tone is heard.
P 2: Press the SIG key if it is desired for the calledstation to hear ringing.
nswerP 1: MICM key flashes, indicating an incoming
call. Ring tone may also be heard.
P 2: Press MICM.
P 3: Lift handset or press key, LED lights
solid green.
STEP 4: If called station is engaged in a non-incall, the station may press MICM afteroriginal caller on hold (with ke
To Bridge Into A Manual Intercom Ca
STEP 1: Press MICM, lift handset or press
STEP 2: A three-party conference is establishe
CONF1:25 PM MON 12 JUL 2010
30/710 DT330/310
Speaker
Called party
ICM 21:25 PM MON 12 JUL 2010
Calling party
ICM 11:25 PM MON 12 JUL 2010
Speaker
Note: Bridging is an optional feature.
Note: The SIG key signals the correspondingwhen speaking over the intercom path isessary.
Note: Two-button Manual Intercom provides onefor signalling and one for talking. A separnaling button can be used in many wayssecretary to alert a boss, or vice versa.
HOLD
Spea
Overriding party
OVERRIDE 11:25 PM MON 12 JUL 2010
CONF1:25 PM MON 12 JUL 2010
DIATo ISTE
STE
STE
To ASTE
STE
STE
STE
r press
d.
groupe calledg their
135
L INTERCOM
nitiateP 1: Lift handset or press the key.
P 2: Press DICM key.
P 3: Dial desired intercom station number. Re-ceive ringback tone.
nswerP 1: DICM LED flashes, indicating an incoming in-
tercom call.
P 2: Press DICM.
P 3: Lift handset or press key. LCD showssolid green.
P 4: If called station is engaged in a non-intercomcall, the station may press DICM after placingthe original call on hold (with key.)
To Bridge Into A Dial Intercom Call
STEP 1: Press the DICM key, lift handset o key.
STEP 2: A three-party conference is establishe
DT730/710 DT330/310
Speaker
Called party
ICM 21:25 PM MON 12 JUL 2010
Speaker
HOLD
Calling party
ICM 21:25 PM MON 12 JUL 2010
Note: Bridging is an optional feature.
Note: Dial intercom provides a Dial Intercomwhere each member of the group may bby a 1- or 2-digit number without usinprime lines.
Speaker
Overriding party
OVERRIDE 31:25 PM MON 12 JUL 2010
CONF1:25 PM MON 12 JUL 2010
COSTE
STE
STE
STE
STE
UsinSTE
STE
STE
L
to con-aller is
l caller. hold.
le to al-
L
amp-onED of
placed
lished.
al call.
Not or trunk
136
NFERENCE
P 1: With call in progress, ask party to hold.
P 2: Press key, receive interrupted dialtone.
P 3: Dial desired number.
P 4: After call is answered, press key. TheLED lights.
P 5: Three-way conference is established.
g Soft KeyP 1: With a call in progress, press key and
dial desired number.
P 2: After call is answered, press CONF Soft Key.Three-way conference is established.
P 3: If one party hang up, other two remain con-
nected. Conf LED goes out.
TO ESTABLISH A BROKER CAL
STEP 1: While engaged in a call and wishing sult a third party, press key. Cautomatically placed on hold.
STEP 2: Dial desired party to consult.
STEP 3: Press key to return to originaThird party is automatically placed on
STEP 4: By repeating these steps, it is possibternate between calls.
TO ANSWER A CAMPED-ON CAL
STEP 1: While engaged in a call, receive the cindication (one short tone burst). L
key flashes.
STEP 2: Press key. Call in progress ison hold.
STEP 3: Connection to camped-on call is estab
STEP 4: Press key to return to originCamped-on call is placed on hold.
e: The Conf key is accommodated on only DTL-2E-1, ITL-2E-1 and DTL-6DE-1. If using the termi-
nals without key, use a soft key or pro-grammable feature key to which conferencefeature has been assigned.
DT730/710 DT330/310
Transfer
Conf
CONF1:25 PM MON 12 JUL 2010
Conf
Transfer
CONF
MIC >>>1:25 PM MON 12 JUL 2010
Note: The display indicates connected station at any given time.
DT730/710 DT330/310
Transfer
Transfer
DT730/710 DT330/310
Answer
Answer
Answer
STE
CA
To PTouSTE
STE
STE
STE
STE
To ASTE
n.
ive dial
tone.
Not
DT7
137
P 5: By repeating these steps, it is possible to al-ternate between calls. Display indicates con-nected station or trunk at any given time.
LL WAITING - ORIGINATING
rogram Call Waiting Key (On One-ch Speed Calling Key)P 1: Press key.
P 2: Press desired One-Touch Speed Callingkey.
P 3: Press key.! appears on LCD.
P 4: Dial “Call Waiting” feature access code.
P 5: Press key.
ctivate Call Waiting – OriginatingP 1: Dial desired station number, receive busy
tone.
STEP 2: Press CALL WAITING.
STEP 3: Receive special ringback tone.
STEP 4: Call waiting tone is sent to busy statio
– Or –
STEP 4: Lift handset or press key.
STEP 5: Dial “Call Waiting” access code, recetone.
STEP 6: Dial busy station.
Using Soft KeySTEP 1: Dial desired station and receive busy
e: To program a hook switch for transfer or featureactivation, press as first digit. “!” dis-plays on LCD.
typeTrunk
numberTrunk
CAMP ON DDD 31:25 PM MON 12 JUL 2010
30/710 DT330/310
Feature
Recall
Feature
Recall
Called stationnumber
C WAIT 20001:25 PM MON 12 JUL 2010
Speaker
C WAIT1:25 PM MON 12 JUL 2010
C WAIT SET 20001:25 PM MON 12 JUL 2010
STE
To ASTE
STE
STE
STE
UsinSTE
STE
tomati-
138
P 2: Press CW Soft Key receive call waiting ring-back tone.
nswer A Waiting CallP 1: Call Waiting Tone is heard.
P 2: Press key.
P 3: Waiting call is automatically connected. Orig-inal party is placed on hold.
P 4: By repeatedly pressing key, it is pos-sible to alternate between calls. Display indi-cates connected station or trunk at any giventime.
g Soft KeyP 1: Hear burst of tone Display indicates “C WAIT”
and key flashes.
P 2: Press key receive call waiting tone.
To DisconnectSTEP 1: Press key. Station user is au
cally connected to original party.
Called stationnumber
C WAIT SET 2000
MIC >>>1:25 PM MON 12 JUL 2010
Answer
Answer
Calling stationnumber
C WAIT 20011:25 PM MON 12 JUL 2010
Answer
Answer
Calling stationnumber
C WAIT 2001
MIC >>>1:25 PM MON 12 JUL 2010
Recall
CATo PSpeSTE
STE
STE
STE
STE
To PSTE
To ROrigSTE
STE
mote
all.
139
LL PARK
rogram Call Park Key (On One-Touch ed Calling Key)P 1: Press key.
P 2: Press One-Touch Speed Calling key.
P 3: Press key. “!” displays on LCD.
P 4: Dial “Call Park” access code.
P 5: Press key again.
ark A CallP 1: While connected to a station or trunk, press
CALL PARK.
etrieve A Parked Call From inating Station
P 1: Dial “Call Park” local retrieval code.
P 2: Station user is connected to parked call.
To Retrieve A Parked Call From A ReStationSTEP 1: Dial “Call Park” local retrieval code.
STEP 2: Station user is connected to parked c
DT730/710 DT330/310
Feature
Recall
Feature
Parked stationor trunk
CALLPARK SET DDD 31:25 PM MON 12 JUL 2010
Elapsed time
10:01 DDD 21:25 PM MON 12 JUL 2010
parked the callStation that
2000 DDD 21:25 PM MON 12 JUL 2010
CA
WheSTE
STE
STE
STE
UsinSTE
STE
.
.
station
and the
hed.
on hold
DT7
140
LL PICK-UP (GROUP)
n Station Within Pick-up Group RingsP 1: Lift handset.
P 2: Press CALL PICK-UP or dial “Call Pick-up”access code (may be stored on One-TouchSpeed Calling key).
P 3: Connection to calling party is established.
P 4: If currently on a call, press key anddial “Call Pick-up” access code.The original party is placed on hold.
g Soft KeyP 1: Lift handset and press PICK Soft Key.
P 2: Connection to calling party is established.
CALL PICK-UP (DIRECT)
To Program Pick-up Direct Key (One-Touch Speed Calling Key)STEP 1: Press key.
STEP 2: Press One-Touch Speed Calling key
STEP 3: Dial “Direct Call Pick-up” access code
STEP 4: Press key again.
When A Station Within System RingsSTEP 1: Lift handset, receive dial tone.
STEP 2: Press PICK-DIRECT and dial the number to be picked up.
– Or –
STEP 2: Dial “Direct Call Pick-up” access code station number to be picked up.
STEP 3: Connection to calling party is establis
STEP 4: If busy, original call must be placed before new call can be picked up.
30/710 DT330/310
Transfer
stationCalling
partyCalled
PICK UP 32000 DDD1:25 PM MON 12 JUL 2010
stationCalling
partyCalled
PICK UP 2001
MIC >>>
2000 1:25 PM MON 12 JUL 2010
DT730/710 DT330/310
Feature
Feature
stationCalling
partyCalled
PICK UP 32000 DDD1:25 PM MON 12 JUL 2010
OU
If TrSTE
STE
STE
OF
STE
STE
STE
STE
ne.
ne and
DT7
DT7TL-2E-
141
TGOING TRUNK QUEUING
unk Is BusyP 1: Receive Trunk Busy indication. Press CALL
BACK. Call is placed in queue for next avail-able trunk.
P 2: When trunk is available, setting station isalerted by ringing and flashing red LED.
P 3: Press key or lift handset. Dial tone isheard or number is automatically dialed ifLeast Cost Routing is provided.
F-HOOK TRUNK QUEUING
P 1: Press key, receive dial tone.
P 2: Dial desired telephone number. Encounter atrunk busy condition.
P 3: Station user receives service set tone andleaves speaker on.
P 4: The desired number is automatically dialedwhen a trunk becomes available.
EXECUTIVE OVERRIDE
If Called Station Is BusySTEP 1: Press OVERRIDE.
STEP 2: Interrupted parties receive warning to
STEP 3: Three-way conference is initiated.
STEP 4: Conf LED lights.
Using Soft KeySTEP 1: Press E-OVR Soft Key.
STEP 2: Interrupted parties receive warning tothree-way conference is initiated.
30/710 DT330/310
Speaker
OG-Q SET1:25 PM MON 12 JUL 2010
30/710 DT330/310
Speaker
Note: The Conf key is accommodated on only D1, ITL-2E-1 and DTL-6DE-1.
DT730/710 DT330/310
Overridden station
OVERRIDE 20011:25 PM MON 12 JUL 2010
CONF1:25 PM MON 12 JUL 2010
OVERRIDE 2001
MIC >>>1:25 PM MON 12 JUL 2010
LAS
To RSTE
STE
STE
STE
LS
MULTI-
g – Allial dial
ephone
the DTetting).
ll Calls
tone.
ne.
Not
Not
DT7
142
T NUMBER REDIAL
ecall Last Number DialedP 1: Press key. Last number dialed is dis-
played.
P 2: Press key until desired number is dis-played. Up to 5 previously dialed numbers.
P 3: Press # or . The number on the display isautomatically redialed.
P 4: When party has answered, lift handset orspeak hands-free.
CALL FORWARDING - ALL CAL
To SetSTEP 1: Press key. Receive dial tone.
STEP 2: If setting for another station, press LINE APPEARANCE.
STEP 3: Press FWD or dial “Call ForwardinCalls” access code. Receive spectone.
STEP 4: Dial destination station or external telnumber. Receive service set tone.
STEP 5: FWD LED lights (at your station or atSeries of the multiline station you are s
STEP 6: Press key. Call Forwarding – Ais set.
Using Soft KeySTEP 1: Press FDA Soft Key. Receive special
STEP 2: Dial destination; wait for service set to
e: Override may be programmed by the TelephonyServer Admin. for one of the Programmable fea-ture keys, or may be programmed on a One-Touch Speed Calling key by storing the Recalland Override access code.
e: A-law Countries [Europe, Australia, Russia, LatinAmerica, Middle near East, other Asian nations]:#µ-law Countries [North America, Japan, HongKong, Taiwan]:
30/710 DT330/310
Redial
LNR[# or ]/SPD[_ _] –XXXXXXX
MIC PICK FDA >>>
Redial
DT730/710 DT330/310
Speaker
Speaker
Forwardingstation
FORWARD SET 20001:25 PM MON 12 JUL 2010
STE
To VSTE
STE
To CSTE
STE
STE
WARD
Not
143
P 3: “FORWARD SET” is displayed, call forward-ing for all calls is set.
erify (Only For Terminal With LCD)P 1: Press FWD.
P 2: Display indicates the station number calls areforwarded to.
ancelP 1: Press key. Receive dial tone. If can-
celing for another station, press MULTILINEAPPEARANCE.
P 2: Press FWD or dial “Call Forwarding – AllCalls” cancel code. Receive service set tone.LED goes out at your station (or the DT Se-ries of the multiline station).
P 3: Press key. Call Forwarding – All Callsis cancelled.
Using Soft KeySTEP 1: Press FDA Soft Key.
STEP 2: Receive service set tone and “FORCANCEL” is displayed.
e: With Soft Key operation, FDB flashes on the dis-play.
FORWARD SET
MIC >>>1:25 PM MON 12 JUL 2010
Forwardingstation
FORWARD 20001:25 PM MON 12 JUL 2010
Speaker
Speaker
FORWARD CANCEL1:25 PM MON 12 JUL 2010
FORWARD CANCEL
MIC >>>1:25 PM MON 12 JUL 2010
CA
To SSTE
STE
STE
STE
STE
STE
UsinSTE
STE
STE
D)
alls are
If can-TILINE
rding –ice set
the DT
DT7
the dis-
144
LL FORWARDING - BUSY LINE
etP 1: Press key. Receive dial tone.
P 2: If setting for another station, press MULTI-LINE APPEARANCE.
P 3: Press FWD-BY or dial “Call Forwarding –Busy Line” access code. Receive special dialtone.
P 4: Dial destination station or external telephonenumber. Receive service set tone.
P 5: FWD-BY LED lights (at your station or at theDT Series of the multiline station you are set-ting).
P 6: Press key. Call Forwarding – BusyLine is set.
g Soft KeyP 1: Press FDB Soft Key. Receive special dial
tone.
P 2: Dial destination; wait for service set tone.
P 3: “FORWARD SET” is displayed; Call Forward-
ing – Busy Line is set.
To Verify (Only For Terminal With LCSTEP 1: Press FWD-BY.
STEP 2: Display indicates the station number cforwarded to.
To CancelSTEP 1: Press key. Receive dial tone.
celing for another station, press MULAPPEARANCE.
STEP 2: Press FWD-BY or dial “Call ForwaBusy Line” cancel code. Receive servtone. LED goes out at your station (orSeries of the multiline station).
30/710 DT330/310
Speaker
Speaker
FORWARD SET1:25 PM MON 12 JUL 2010
Note: With Soft Key operation, FDB flashes on play.
FORWARD SET
MIC >>>1:25 PM MON 12 JUL 2010
Forwarding station
FORWARD 20001:25 PM MON 12 JUL 2010
Speaker
STE
UsinSTE
STE
CAL
To SSTE
STE
STE
STE
r at theare set-
– Don’t
ial dial
ne.
orward-
D)MULTI-
DT7
145
P 3: Press key. Call Forwarding – BusyLine is cancelled.
g Soft KeyP 1: Press FDB Soft Key.
P 2: Receive service set tone and “FORWARDCANCEL” is displayed.
L FORWARDING - DON’T ANSWER
etP 1: Press key. Receive dial tone.
P 2: If setting for another station, press MULTI-LINE APPEARANCE.
P 3: Press FWD-NA or dial “Call Forwarding –Don’t Answer” access code. Receive specialdial tone.
P 4: Dial destination station or external telephonenumber. Receive service set tone.
STEP 5: FWD-NA LED lights (at your station oDT Series of the multiline station you ting).
STEP 6: Press key. Call Forwarding Answer is set.
Using Soft KeySTEP 1: Press FDN Soft Key. Receive spec
tone.
STEP 2: Dial destination; wait for service set to
STEP 3: “FORWARD SET” is displayed; Call Fing – Don’t Answer is set.
To Verify (Only For Terminal With LCSTEP 1: If verifying for another station, press
LINE APPEARANCE while idle.
STEP 2: Press FWD-NA.
Speaker
FORWARD CANCEL1:25 PM MON 12 JUL 2010
FORWARD CANCEL
MIC >>>1:25 PM MON 12 JUL 2010
30/710 DT330/310
Speaker
Speaker
Forwarding station
FORWARD SET 20001:25 PM MON 12 JUL 2010
FORWARD SET
MIC >>>1:25 PM MON 12 JUL 2010
STE
To CSTE
STE
STE
LL
Out IPe.
ive ser-
key.ation is
ial Dial
D SET”
Not
Not r
146
P 3: Display indicates the station number calls areforwarded to.
ancelP 1: Press key. Receive dial tone. If can-
celing for another station, press MULTILINEAPPEARANCE.
P 2: Press FWD-NA or dial "Call Forwarding -Don't Answer" cancel code. Receive serviceset tone. LED goes out at your station (or theDT Series of the multiline station).
P 3: Press key. Call Forwarding – Don’tAnswer is cancelled.
LOGGED OUT IP STATION - CADESTINATION To SetSTEP 1: Lift handset or press key.
STEP 2: Press the FDL Key or dial “Logged Station – Call Destination” access cod
STEP 3: Dial destination station number; recevice set tone.
STEP 4: Replace handset or press Logged Out IP Station – Call Destinset.
Using Soft KeySTEP 1: Press FDL Soft Key; receive spec
Tone.
STEP 2: Dial destination station number.
STEP 3: Receive service set tone; “FORWARis displayed.
e: Call Forwarding for Busy Line and Don't Answermay be combined depending upon system pro-gramming.
e: With Soft Key operation, FDB flashes on the dis-play.
Forwarding station
FORWARD 20001:25 PM MON 12 JUL 2010
Speaker
Speaker
FORWARD CANCEL1:25 PM MON 12 JUL 2010
DT730
Speaker
Speake
FORWARD SET XXXX1:25 PM MON 12 JUL 2010
FORWARD SET XXXX
MIC >>>1:25 PM MON 12 JUL 2010
To VSTE
STE
To CSTE
STE
STE
UsinSTE
et tone.
ive ser-
ination”ppears
Not
147
erify (Only For Terminal with LCD)P 1: Press “Logged Out IP Station – Call Destina-
tion” feature key lit red or press FDL.
P 2: Display indicates the station number calls areforwarded.
ancelP 1: Lift handset or press key; receive Dial
Tone.
P 2: Press the FDL Key or dial “Logged Out IPStation – Call Destination” cancel code; re-ceive service set tone.
P 3: Replace handset or press key.Logged Out IP Station – Call Destination iscanceled.
g Soft KeyP 1: Lift handset or press key; receive Dial
Tone.
STEP 2: Press FDL Soft Key; receive service s
STEP 3: Dial destination station number; recevice set tone.
STEP 4: “Logged Out IP Station – Call Destlamp goes off and FDL indication disaon the LCD.
e: With Soft Key Operation, FDL flashes on the dis-play.
FORWARD XXXX1:25 PM MON 12 JUL 2010
Speaker
Speaker
FORWARD CANCEL1:25 PM MON 12 JUL 2010
Speaker
FORWARD CANCEL
MIC >>>1:25 PM MON 12 JUL 2010
CAIf CSTE
– Or
STE
STE
STE
ice set
the CB
ER
stored.
ory.
lephony key or
ng key.
148
LL BACK
alled Station is BusyP 1: Press CALL BACK. Receive service set tone.
–
P 1: Press the FLASH key and enter “Call Back”access code.
P 2: When both parties become idle, calling par-ty's phone rings. Calling party would go offhook and hear ring back tone.The called station would then be ringing.
P 3: Connection is established when the calledparty answers.
Using Soft KeySTEP 1: Press CB Soft Key and receive serv
tone.
STEP 2: “CALLBACK SET” is displayed and Soft Key flashes on the display.
TO SAVE AND REPEAT A NUMB
To SaveSTEP 1: Press key.
STEP 2: Dial desired telephone number.
STEP 3: Press S&R. Dialed number is now S&R LED lights.
– Or –
STEP 3: Receive internal call.
STEP 4: Press S&R. Number is stored in mem
DT730/710 DT330/310
Called party
CALLBACK SET 20001:25 PM MON 12 JUL 2010
Called party
CALLBACK 20001:25 PM MON 12 JUL 2010
Called party
CALLBACK 20011:25 PM MON 12 JUL 2010
Note: Call Back may be programmed by the TeServer Admin. on a Programmable featureby the user on a One-Touch Speed Calli
CALLBACK SET
MIC >>>1:25 PM MON 12 JUL 2010
DT730/710 DT330/310
Speaker
STE
UsinSTE
STE
To VSTE
STE
To RSTE
STE
STE
UsinSTE
Not
149
P 5: S&R LED lights.
g Soft KeyP 1: Press S&R. Number is stored in memory.
P 2: S&R LED lights.
erify (Only For Terminal With LCD)P 1: While idle, press S&R.
P 2: Display indicates digits sorted.
epeatP 1: Press key.
P 2: Press S&R. DT Series automatically redialsthe programmed number.
P 3: S&R automatically cancelled. LED goes out.
g Soft KeyP 1: Press flashing S&R Soft Key. Stored number
is automatically redialed. “S&R” disappearsfrom display.
e: If saved number is busy or no answer is received,to save it again, press S&R again before hangingup.
Speaker
TO
STE
STE
STE
STE
essag-
press
e is au-
ing thessage.
Not
Not
Not
DT7
150
LEAVE A MESSAGE
P 1: Press key. Receive dial tone.
P 2: Dial desired station number. Encounter noanswer or busy condition.
P 3: Press MSG. Message is sent to called DT Se-ries.
P 4: Called station MSG LED lights.
TO ANSWER A MESSAGE
To DisplaySTEP 1: MSG LED is lit. Station is idle.
STEP 2: Press MSG.
STEP 3: Re-press MSG to display additional mes in order received.
To RespondSTEP 1: While displaying desired message,
key.
STEP 2: Press MSG. Station which left messagtomatically redialed.
STEP 3: Message is erased.
To EraseSTEP 1: To erase a message without return
call, press MSG to display desired me
e: Up to four messages can be stored in DT Seriesmemory.
e: If a fifth message is attempted, reorder tone isheard and display indicates as follows:
e: If station is not equipped to receive messages,reorder tone is heard and display indicates as fol-lows:
30/710 DT330/310
Speaker
Called station
MESSAGE SET 20011:25 PM MON 12 JUL 2010
MESSAGE BUSY1:25 PM MON 12 JUL 2010
MESSAGE REST1:25 PM MON 12 JUL 2010
DT730/710 DT330/310
stationCalling
MSG 2001 12:28PM1:25 PM MON 12 JUL 2010
Speaker
STE
VO
To SSTE
STE
STE
STE
To OSTE
STE
menu
(En-
access
ials
ontinu-
Not
DT7
151
P 2: Dial # or while message displays. Mes-sage is erased.
ICE MAIL SYSTEM
etP 1: Press key.
P 2: Press (Enter) or key.
P 3: Dial desired “Voice Mail System” accesscode.
P 4: Press key again.
riginateP 1: Press key.
P 2: Hear ringback tone.
– Or –
STEP 2: Press (Enter) key. The Shortcutscreen is displayed on LCD.
STEP 3: Select Voice Mail and then press ter), (Right-cursor) or OK soft key toa preset Voice Mail System.
STEP 4: Hear ringback tone.
MEET-ME PAGING
Example: Station A can page Station B. When Station B danswer code, they are connected.
To Page (Station A)STEP 1: Dial “Paging” access code, receive c
ous ringback for one second.
STEP 2: Page station B.
STEP 3: Remain off hook or hang up.
e: If station that left message is busy, callback orMSG may be set. If station that left messagedoes not answer, MSG may be set, notifying orig-inating party that a message return wasattempted.
MESSAGE CANCEL1:25 PM MON 12 JUL 2010
30/710 DT330/310
Feature
Message
Feature
SPEED SET1:25 PM MON 12 JUL 2010
Message
2
DT730/710 DT330/310
Trunk number
PAGING 31:25 PM MON 12 JUL 2010
To AIf StaSTE
If StaSTE
STE
PAG
ExamStatinot aStatianno
ted dial
ontinu-
, and isnounc-
Not
DT7
152
nswer (Station B)tion A remains off hook
P 1: Station B dials “Paging” answer code, andthey are immediately connected.
tion A hung upP 1: Station B dial “Paging” answer code, and Sta-
tion A DT Series rings.
P 2: When station A goes off-hook, they are con-nected.
ING TRANSFER
ple:on A receives an important call for Station B who is t a desk. Station A can page Station B. When
on B dials the Paging answer code, Station A can unce the call and transfer it to Station B.
Station A PagingSTEP 1: Ask calling party to hold.
STEP 2: Press key. Receive interruptone.
STEP 3: Dial “Paging” access code. Receive cous ringback for one second.
STEP 4: Page Station B.
STEP 5: Remain off-hook or hang up.
To Answer (Station B)If Station A remained off hookSTEP 1: Station B dials “Paging” answer code
connected with Station A. Station A anes call.
e: Paging function can not be supported with IPenabled DT700 Series.
PAGING 31:25 PM MON 12 JUL 2010
30/710 DT330/310
Calling trunknumber
TRANSFER DDD 31:25 PM MON 12 JUL 2010
Transfer
Stations A and B each displaythe other’s number
TRANSFER XXXX1:25 PM MON 12 JUL 2010
STE
If StaSTE
STE
STE
– Or
(Dep
STE
153
P 2: Station A hangs up. Station B and the callingparty are connected.
tion A hung upP 1: Station B dials “Paging” answer code. Station
A DT Series rings.
P 2: Station A picks up and announces call.
P 3: Station A hangs up. Station B and the callingparty are connected.
–
endent on System Programming)
P 3: Station B dials “Paging” answer code, and isimmediately connected to the calling party.
DDD 31:25 PM MON 12 JUL 2010
Stations A and B each displaythe other’s number, flashing
TRANSFER DDD 31:25 PM MON 12 JUL 2010
Calling trunk number
DDD 31:25 PM MON 12 JUL 2010
PAGING DDD 31:25 PM MON 12 JUL 2010
BO
SecSTE
STE
STE
If BoSTE
STE
If BoSTE
arty to
No ser-
y to
ey and
eceive
DT7
154
SS/SECRETARY TRANSFER
retaryP 1: Lift handset, press boss’ ringing line. Ask call-
ing party to hold.
P 2: Press boss’ line again. “Voice Call” is auto-matically established.
P 3: Announce the call to the boss.
ss Accepts CallP 1: Secretary replaces handset.
P 2: Secretary presses boss’ line to return to call-ing party.
ss Refuses CallP 1: Secretary presses boss’ line to return to call-
ing party.
BOSS/SECRETARY - MW LAMPCONTROL
To Set MW at Boss’ StationWith caller on the lineSTEP 1: Lift handset or press key.
STEP 2: Press boss’ ringing line. Ask calling phold.
STEP 3: Press the MW-SET line/feature key. vice set tone is heard.
Boss sees MW on display and can call secretarreceive message.
Without caller on the lineSTEP 1: After taking message, press k
receive dial tone.
STEP 2: Press the MW-SET line/feature key. Rservice set tone.
30/710 DT330/310
Calling party
DDD 31:25 PM MON 12 JUL 2010
Boss and secretary station eachdisplay the other’s number
ICM XXXX1:25 PM MON 12 JUL 2010
DT730/710 DT330/310
Speaker
MW SET1:25 PM MON 12 JUL 2010
Recall
MW SET1:25 PM MON 12 JUL 2010
To CWithSTE
STE
STE
WithSTE
, but is
Key
ey.
s code.
.
aller to
eceive
Not
Transfer
155
ancel At Boss’ Station caller on the lineP 1: Lift handset or press key. Receive dial
tone.
P 2: Press Boss’ line appearance.
P 3: Press MW-CANCEL line/feature key. Re-ceive service set tone.
caller on the lineP 1: While engaged in conversation on boss’ mul-
tiline, press MW-CANCEL key. No serviceset tone is heard.
BOSS SECRETARY OVERRIDE
Example:Station 2000 is boss, Station 2001 is secretary.Boss is connected to Trunk A.Incoming call on Trunk B connects to secretaryintended for boss.
To Program Boss/Secretary OverrideSTEP 1: Press key.
STEP 2: Press a One-Touch Speed Calling k
STEP 3: Dial “Boss/Secretary Override” acces
STEP 4: Press key. – displays on LCD
STEP 5: Dial boss’ station number.
STEP 6: Press key again.
SecretarySTEP 1: Lift handset to answer Trunk B, ask c
hold.
STEP 2: Press CALL HOLD feature key or key and dial call hold access code. RDial Tone.
e: The secretary can hang up after taking a mes-sage, and set a message lamp at any time bygoing off-hook on the boss’ multiline and press-ing the MW-SET key.
Speaker
MW CANCEL1:25 PM MON 12 JUL 2010
MW CANCEL1:25 PM MON 12 JUL 2010
DT730/710 DT330/310
Feature
Recall
Feature
STE
BosSTE
OptiSTE
STE
STE
OptiSTE
STE
p.
parties
of tone,
es with
y to re-
s when
0/310
156
P 3: Press BOSS/SEC OVERRIDE. ReceiveRingback Tone.
sP 1: Hear 3 bursts of tone. LCD indicates:
on 1P 1: Boss presses key and converses with
secretary. Trunk A is placed on hold.
P 2: Secretary hangs up. Boss is connected toTrunk B.
P 3: Boss can alternate between the two partiesby pressing key.
on 2P 1: Boss presses key and converses with
secretary. Trunk A is placed on hold.
P 2: Boss presses station 01 key and converseswith Trunk B. Boss presses key to re-
connect to Trunk A.
STEP 3: Secretary hears reorder tone, hangs u
STEP 4: Boss can alternate between the twoby pressing key.
Option 3STEP 1: If boss does not respond to 3 bursts
secretary presses key.
STEP 2: Secretary is connected to Trunk B.
Option 4STEP 1: Boss presses key and convers
Secretary. Trunk A is placed on hold.
STEP 2: Boss denies call, presses keturn to Trunk A.
STEP 3: Secretary is returned to Trunk B.
DO NOT DISTURB
While Idle (On Hook)STEP 1: Press DND. LED lights.
Boss’ stationnumber
C WAIT 20001:25 PM MON 12 JUL 2010
Secretary’s stationnumber
C WAIT 20011:25 PM MON 12 JUL 2010
Answer
Answer
Answer
Answer
Note: With Soft Key operation, "DND" flasheset.
Answer
Recall
Answer
Transfer
DT730/710 DT33
DND SET1:25 PM MON 12 JUL 2010
To CSTE
UsinSTE
display ng Call g a direct stina-ns-r being
swer to
isplays
ey.
and the.
swer to
Not only.
/310
157
ancelP 1: Press DND. LED goes out.
g Soft KeyP 1: Press flashing DND Soft Key.
CALL REDIRECT
Example: DT Series Station A views on the DT Series the Station Number or Caller ID of an Incomiand immediately redirects the call by pressinFunction Key. The destination of the Call Rewill be the Call Forwarding-Don’t Answer Detion or the Recall Destination if the call is traferred without Call Forwarding-Don’t Answeset at the station.
Call Redirect To Call Forward-Don’t Answer DestinationSTEP 1: Station A sets Call Forward-Don’t An
Station B.
STEP 2: Station C dials Station A, it rings and dStation C’s number on the display.
STEP 3: Station A presses the Call Redirect K
STEP 4: REDIRECT is displayed on the LCD, call immediately forwards to Station B
Using Soft KeySTEP 1: Station A sets Call Forward-Don’t An
Station B.
e: DND must be programmed by the TelephonyServer Admin. on a Programmable feature key.
DND CANCEL1:25 PM MON 12 JUL 2010
DND CANCEL
MIC DND >>>Note: This feature is available in North America
DT730/710 DT330
STE
STE
STE
- Or
CallIs TrAnsSTE
STE
STE
STE
STE
UsinSTE
STE
STE
STE
STE
for the
flashes
for the
utomat-
158
P 2: Station C dials Station A, it rings and displaysStation C’s number on the display.
P 3: Station A presses the REDIR Soft Key.
P 4: REDIRECT is displayed on the LCD, and thecall immediately forwards to Station B.
-
Redirect to Recall Destination When Call ansferred Without Call Forwarding-Don't wer Being SetP 1: Station B calls Station C.
P 2: Station C answers the call and transfers it toStation A and then releases the call.
P 3: Station A rings.
P 4: Station A presses the Call Redirect Key.
P 5: REDIRECTING is displayed on Station A andthe call immediately recalls to Station C.
g Soft KeyP 1: Station B calls Station C.
P 2: Station C answers the call and transfers it toStation A and then releases the call.
P 3: Station A rings.
P 4: Station A presses the REDIR Soft Key.
P 5: REDIRECTING is displayed on Station A andthe call immediately recalls to Station C.
PRIVACY
While Off-HookSTEP 1: Press DND. LED lights.
STEP 2: Privacy feature prevents interruptionsduration of the call.
Using Soft KeySTEP 1: Press flashing DND Soft Key. “DND”
when set.
STEP 2: Privacy feature prevents interruptionsduration of the call.
To CancelSTEP 1: Press DND. LED goes out.
– Or –
STEP 1: Replace handset. Privacy feature is aically cancelled.
DT730/710 DT330/310
PRIVACY SET1:25 PM MON 12 JUL 2010
PRIVACY SET
MIC >>>1:25 PM MON 12 JUL 2010
PRIVACY CANCEL1:25 PM MON 12 JUL 2010
UsinSTE
PR
ExamDap
STE
tation
key.
of Sta-
ter the
parties
.
Not
Not
DT7
ker
159
g Soft KeyP 1: Press flashing DND Soft Key.
IVACY RELEASE
ple: T Series Station B is engaged in a conversation, nd allows DT Series Station A to enter the call in rogress.
P 1: Station A lifts handset or presses key.Station A presses the line appearance of Sta-tion B.Warning tone is sent to the interrupted par-ties (optional).A three-way conference is established.
– OR –
Example: DT Series Station A requests entrance into SB’s call in progress.
STEP 1: Station A lifts handset or presses
STEP 2: Station A presses the line appearancetion B.
STEP 3: Station B LCD indicates as follows:
STEP 4: Station B may allow Station A to enconversation by pressing P-RLS.
STEP 5: Warning tone is sent to the interrupted(optional).
STEP 6: A three-way conference is established
e: DND must be programmed by the TelephonyServer Admin. on a Programmable feature key.
e: Station A may also be a single-line station aslong as it appears on the Station B DT Series.
PRIVACY CANCEL
MIC DND >>>1:25 PM MON 12 JUL 2010
30/710 DT330/310
Speaker
CONF1:25 PM MON 12 JUL 2010
Spea
WAIT P-RLS?1:25 PM MON 12 JUL 2010
P-RLS?1:25 PM MON 12 JUL 2010
CONF1:25 PM MON 12 JUL 2010
cal
The
to 100 entries digits 4
in Idle
Not
Not
LCD.
s the For
160
PHONEBOOK
There are two types of Phonebook features: LoPhonebook and System Phonebook.
System PhonebookSystem Phonebook is used on a system basis. data entry is made by the Telephony Server Administrator.
Local PhonebookLocal Phonebook is used on a station basis. Upentries are available per station. You can make with key operation from the telephone. Up to 32can be registered for each dial number. Up to 2characters can be registered for each name.
• SYSTEM PHONEBOOK
To Search And Make A Call
Example: To Search For “NEC BNET”.
STEP 1: Press Pbook soft key while Station isstate.
e: Station A can be a single-line station if it appearson the Station B DT Series.
e: Up to six parties can break into a two-party con-versation (additional devise is required).
Note: This feature is available for DT series with
Note: When the system administrator invalidatePhonebook, this feature cannot be used. details contact the system administrator.
DT730/710 DT330/310
K soft
Not
e Menu
screen,
oretween
161
If Local Phonebook is enabled by the setting on the system side, go to STEP2.If Local Phonebook is disabled by the setting on the system side, go to STEP 3.
- OR -
Press key to display the Menu screen. On the Menu screen, select Directory.
If Local Phonebook is enabled by the setting on the system side, go to STEP 2.If Local Phone is disabled, the display changes as follows. In that case, select System and go to STEP 3.
STEP 2: Press Sys soft key.
STEP 3: Enter a name and then press or Okey to perform a search.
Ex. To enter “NEC”:Press key twice to enter “N”.Press key four times to enter “E“.Press key twice to enter “C“.e: Select an item on the menu screen in either of
the following two ways.• Press an appropriate digit key.• Highlight a desired item and then press
or OK soft key.
Pbook MIC DND
1:25 PM MON 12 JUL 2010
Menu
2
History
Back OK
12
Tool3Directory
2
Note: This feature cannot be activated from thkey on DT710 Series (ITL-6DE-1).
Note: If “>>>” soft Key is pressed on the above
the following soft keys appear. Pressing Eu-s/Eu-l soft key shifts characters buppercase and lowercase.
Personal
Back OK
12
Corporate3System
PhonebookLocal Sys Cnl
632
Name:
>>>OKClrNEC
STE
STE
STE
Not
Not
screen igits ble limit yed at a eds the y to ame/
ractersits
162
P 4: A result of the search is displayed. Press or UP/DOWN soft key to scroll the result.
P 5: When “NEC BNET” appears, press , or OK soft key.
P 6: The registered Phonebook data for “NEC BNET” appears. From this screen, you can make a call by going off-hook or pressing
key.
e: To delete an entered character, press or Clrsoft key.
e: To move the cursor one space to the right, press key or “” soft key once
<<< -Eu-s Cnl
(Lower-case character)
<<< -Eu-l Cnl
(Upper-case character)
Name: NEC
CnlOKDOWNNEC ABIKOUP
NEC BNETCnlOK
Name: NEC
DOWNUP
Speaker
Note: More soft key appears in Phonebook data when the number of characters (name) or d(telephone number) are exceeding displaya(Up to 17 characters or digits can be displatime). If the name or telephone number excedisplayable limit, press or More soft kedisplay the last 17 characters/digits of the ntelephone number.Example: Name Suzuki Taro(JapanSumida) ¨ 24 chaNumber: 01234567890123456789 ¨ 20 dig
(Display area)Name: Suzuki Taro(JapanSumida)Number: 01234567890123456789
(Display area)Name: Suzuki Taro(JapanSumida)Number: 01234567890123456789
CnlNumber: XXXXXXXXName: NEC BNET
More
NameNumberMore Cnl >>>
: Suzuki Taro(Japan01234567890123456:
NameNumberMore Cnl >>>
: Taro(JapanSumida)34567890123456789:
• L
To A
ExamDT Sits Te
STE
STE
ess
K soft
Notscreen,
oretween
163
OCAL PHONEBOOK
dd New Data
ple: eries Station A registers “NEC” as new name and lephone Number.
P 1: Press Pbook soft key or (Directory) keywhile Station is in Idle state.
- OR -
Press key to display the Menu screen. On the Menu screen, select Directory.
P 2: Press Local soft key.
STEP 3: Local Phonebook screen appears. PrAdd soft key.
STEP 4: Enter a name and then press or Okey.
Ex. To enter “NEC”:Press key twice to enter “N”.Press key twice to enter “E“.Press key three times to enter “C“.
e: Select an item on the menu screen in either ofthe following two ways.
• Press an appropriate digit key.• Highlight a desired item and then press
or OK soft key.
Pbook MIC DND1:25 PM MON 12 JUL 2010
Menu
2
History
Back OK
12
Tool3Directory
Note: If “>>>” soft Key is pressed on the above
the following soft keys appear. Pressing Eu-s/Eu-l soft key shifts characters buppercase and lowercase.
PhonebookLocal Sys Cnl
Local PhonebookCnlAddSrch
632
Add name:
>>>OKClrNEC
<<< -Eu-s Cnl
(Lower-case character)
STE
STE
To SThe Phon
played,istered
“Local
is en-key. (If ge “En-
Not
Not
Not
screen,
oretween
164
P 5: Enter the telephone number by using digit keys and press or OK soft key.
P 6: “NEC” and its telephone number has been added into Local Phonebook. Two seconds later, the display returns to Local Phonebook screen.
earch For Nameprocedure shown below is available in Local ebook.
Example: To Find “NEC BNET”.
STEP 1: While Local Phonebook screen is dispress Srch soft key. (If no data is regin Local Phonebook, the messagephone book empty” appears.)
STEP 2: Name Entry screen appears.
STEP 3: Enter a name (in this example, “NEC”tered) and then press or OK soft no appropriate data exists, the messatry not found!” appears.)
e: To delete an entered character, press or Clrsoft key.
e: To move the cursor one space to the right, press key or “” soft key once
e: To delete an entered digit, press or Clr softkey.
<<< -Eu-l Cnl
(Upper-case character)
Number:Name: NEC
CnlOKClr
Entry added!Note: If “>>>” soft Key is pressed on the above
the following soft keys appear. Pressing Eu-s/Eu-l soft key shifts characters buppercase and lowercase.
Local PhonebookCnlAddSrch
Name:
>>>OKClr
Name:
>>>OKClrNEC
STE
STE
STE
Not
Not
creen gits le limit ed at a ds the to me/
165
P 4: A result of the search is displayed. Press or UP/DOWN soft key to scroll the result.
P 5: When “NEC BNET” appears, press , or OK soft key.
P 6: The registered data for “NEC BNET” ap-pears.From this screen, you can make a call by go-ing off-hook or pressing key.
e: To delete an entered character, press or Clrsoft key.
e: To move the cursor one space to the right, press key or “” soft key once
<<< -Eu-s Cnl(Lower-case character)
<<< -Eu-l Cnl(Upper-case character)
Name: NEC
CnlOKDOWNNEC ABIKOUP
NEC BNETCnlOK
Name: NEC
DOWNUP
Speaker
Note:
More soft key appears in Phonebook data swhen the number of characters (name) or di(telephone number) are exceeding displayab(Up to 17 characters or digits can be displaytime). If the name or telephone number exceedisplayable limit, press or More soft keydisplay the last 17 characters/digits of the natelephone number.
Pref CnlNumber: XXXXXXXXName: NEC BNET
>>>More
To E
ExamTo MNum
STE
STE
STE
STE
e mod-K soft
ears.
screen,
oretween
or Clr
t, press
166
dit An Entry
ple: odify Name “Home” to “House” and Telephone ber “0123456789” to “0123456712”.
P 1: Press >>> soft key while the target Phone-book data is displayed.
P 2: Press EDIT soft key.
P 3: The following name edit screen appears.
P 4: Press or Clr soft key two times to erase “me”.
STEP 5: Enter “use” by using digit keys. After thification has completed, press or Okey.
Press key twice to enter “u”.Press key four times to enter “s“.Press key twice to enter “e“.
STEP 6: The following number edit screen app
Pref CnlNumber: 0123456789Name: Home
>>>More
EDIT DELNumber: 0123456789Name: Home
<<<
Edit Name:
>>>OKClrHome
Edit Name:
>>>OKClrHo
Note: If “>>>” soft Key is pressed on the above
the following soft keys appear. Pressing Eu-s/Eu-l soft key shifts characters buppercase and lowercase.
Note: To delete an entered character, press soft key.
Note: To move the cursor one space to the righ key or “” soft key once.
873
Edit Name:
>>>OKClrHouse
<<< -Eu-s Cnl
(Lower-case character)
<<< -Eu-l Cnl
(Upper-case character)
Number: 0123456789 Cnl
Name: House
Clr OK
STE
STE
STE
To D
STE
he cur-
o sec-e Entry
ral
ber
167
P 7: Press or Clr soft key twice to erase “89”.
P 8: Enter “12” by pressing digit keys and then press or OK soft key.
P 9: The data modification has completed. Two seconds later, the display returns to Local Phonebook screen.
elete A Record
P 1: Press >>> soft key while the target Phone-book data is displayed.
STEP 2: Press DEL soft key.
STEP 3: Press or OK soft key to delete trently displaying data.
STEP 4: The data deletion has completed. Twonds later, the display returns to Namscreen.
To Add A Prefix To Telephone NumbeThe procedure shown below is available in LocPhonebook.
Example: To add a prefix “0184” in front of telephone num“0123456789”
Number: 01234567 Cnl
Name: House
Clr OK
Number: 0123456712Name: House
Clr OK Cnl
Entry edited!
Pref CnlNumber: 0123456789Name: NEC ABIKO
>>>More
EDIT DELNumber: 0123456789Name: NEC ABIKO
<<<
Name: NEC ABIKO
OKDelete this entry?
Cnl
Entry deleted!
STE
STE
STE
Not
screen digits ble limit yed at a eeds the ey to ame/
168
P 1: Press Pref Soft Key while the target Phone-book data is displayed.
P 2: Enter a prefix (In this example, “0184” is en-tered) by using digit keys and press or
OK Soft Key.
P 3: The prefix is added in front of the telephonenumber. Once the prefix is added, Pref SoftKey will disappear.
e: To delete an entered digit, press or Clr softkey.
Pref CnlNumber: 0123456789Name: Takahashi
>>>More
ClrNumber: 0184Prefix Number Input
CnlOK
CnlNumber: 01840123456789Name: Takahashi
More
Note: More soft key appears in Phonebook datawhen the number of characters (name) or (telephone number) are exceeding displaya(Up to 17 characters or digits can be displatime). If the name or telephone number excdisplayable limit, press or More soft kdisplay the last 17 characters/digits of the ntelephone number.
AvaThe Phon
SP: B
DigiCod
Character
#
#
169
ilable Characters In Local Phonebookfollowing tables show available characters in Local ebook.
UPPERCASE CHARACTER
lank Space
LOWERCASE CHARACTER
SP: Blank Space
t e 1 2 3 4 5 6 7 8 9 0 #
. A D G J M P T W SP #, B E H K N Q U X 0: C F I L O R V Y! À È Ì 5 Ñ S Ù Z
? Á É Í Ò Ú 9
- Â Ê Î Ó 7 Û+ Ã Ë Ï Ô Ü% Ä 3 4 Õ 8
& Å Ö/ Æ Œ( Ç Ø) 2 6=
¿¡1
Digit Code 1 2 3 4 5 6 7 8 9 0
Character
. a d g j m p t w SP, b e h k n q u x 0: c f i l o r v y! à è ì 5 ñ s ù z
? á é í ò ú 9
: â ê î ó 7 û\ ä ë ï ô ü“ å 3 4 õ 8
@ æ ö1 ç 6
2
CA
TherhandOn thmemOPE
The the CThis exceof ocup tonam
To VSTE
- OR
STE
oft key.
call is
desired
Not
e Menu
be dis-
swered
170
LL HISTORY
e are two types of Call History features. On the one , the history data is stored in the system memory. e other hand, the history data is stored in the ory of the telephone (see 7.CALL HISTORY RATION).
following describes the operating procedures for all History feature which controlled by the system.Call History feature can store up to 20 records. If eding 20 records, a record will be deleted in order currence. Also, this Call History feature can store 32 digits of dial number and 16 characters of
e information per record.
iew Call HistoryP 1: Press iCall soft key of Call History Feature
key while the current time is displayed onLCD.
-
P 1: Press key to display the Menu screen.On the Menu screen, select History (forDT730 Series)/ Call History (for DT330
Series) and then press or OK s(or press key.)
STEP 2: The history data of the last receiveddisplayed.
STEP 3: Press or soft key to display a history data.
e: When the system administrator invalidates the Phonebook, this feature cannot be used. For details contact the system administrator.
DT730/710 DT330/310
5:25 PM MON 12 JUL 2010iCall MIC DND
Menu
11
Note: This feature cannot be activated from thkey on DT710 Series (ITL-6DE-1).
Note: If no history data is saved, "NO LIST" willplayed on LCD.
Note: Call History will display “!!” for an unanincoming call.
1
Back OK
12
Tool3DirectoryHistory
Pbook31300
1:03 PM MON 12 JUL 2010
>>>
Pbook51500
12:55 PM MON 12 JUL 2010
>>>!!
To MSTE
STE
To MSTE
STE
STE
mation,
make ar.
Not
be set
cluding
or Clr
screen igits ble limit yed at a eds the y to ame/
171
ake A Call From Call HistoryP 1: Display the history data of the target party.
P 2: Go off-hook or press key to make acall to the displayed party.
ake A Call With PrefixP 1: Press >>> soft key while the history data to
which you want to add a prefix.
P 2: Press Pref soft key.
P 3: Enter a prefix by using the digit keys. In thisexample, “012345” is entered. After enteringthe prefix, press or OK soft key.
STEP 4: If the call history data has name inforthe name is displayed as follows:
STEP 5: Go off-hook or press key to call to the displayed telephone numbe
e: While the history data is displayed, you cannotmake a call by dialing a telephone number.
Pbook51500
12:55 PM MON 12 JUL 2010
>>>
Speaker
Pbook31300
1:03 PM MON 12 JUL 2010
>>>
DEL31300
1:03 PM MON 12 JUL 2010
ENDPref<<<
Note: A maximum of 10 digits (0-9, * and #) canas a prefix.
Note: When prefix is added, up to 32 digits inthe prefix can be sent as dial number.
Note: To delete an entered character, press soft key.
Note: More soft key appears in Phonebook data when the number of characters (name) or d(telephone number) are exceeding displaya(Up to 17 characters or digits can be displatime). If the name or telephone number excedisplayable limit, press or More soft kedisplay the last 17 characters/digits of the ntelephone number.
OKNumber:Prefix Number Input
CnlClr
More
Name
CnlNumber
:NEC ABIKO:01234531300
Speaker
To DSTE
STE
To APho
STE
OK soft
red.)
Not
Not
registerords at below to the
history,
screen,
oretween
172
elete A Specific DataP 1: Press >>> soft key while the history data
which you want to delete is displayed.
P 2: Press DEL soft key.
dd Call History Data To Local nebook
P 1: Press Pbook soft key or Phonebook Featurekey while the history data of the target party.
STEP 2: Enter a desired name and then press key.(In this example, “NEC ABIKO” is ente
e: If you want to exit Call History, press END softkey.
e: The Call History data stored on the system canbe added to Phonebook (controlled by the sys-tem) only. The data cannot be added to the Per-sonal Directory (described in 6.DIRECTORYOPERATION) controlled by the telephone.
Pbook31300
1:03 PM MON 12 JUL 2010
>>>
DEL31300
1:03 PM MON 12 JUL 2010
ENDPref<<<
Pbook31300
1:03 PM MON 12 JUL 2010
>>>
Note: Local Phonebook feature allows you to up to 100 records. If exceeding 100 recthis point, the error message shownappears. Press OK soft key to go backabove display.
Note: If name information is stored on the call the name is displayed.
Note: If “>>>” soft Key is pressed on the above
the following soft keys appear. Pressing Eu-s/Eu-l soft key shifts characters buppercase and lowercase.
Entry NG (over)OK
Clr
Add name:
OK >>>NEC ABIKO
<<< -Eu-s Cnl
(Lower-case character)
<<< -Eu-l Cnl
(Upper-case character)
STE
173
P 3: The telephone number stored on the call his-tory is displayed. The telephone number canbe changed if necessary. Press OK soft keyto add the displayed data to Local Phone-book.
Clr
Name
OK CnlNumber
:NEC ABIKO:31300
174
This page is for your notes.
6This of DTyou c
Persentriview
••••••••
TO
STE
creen d.
ons.ss ,
Not
Seriesot sup-
t key to
y once.
m
175
. DIRECTORY OPERATION
chapter explains about Personal Directory function730 Series. By using Personal Directory function,an make a call with simple operation.
onal Directory function can register up to 500es (4 telephone numbers per entry). You can add//edit/delete these entries.
TO ADD NEW DATATO CHANGE GROUP NAMETO FIND A REGISTERED DATATO MAKE A CALL FROM DIRECTORYTO ADD PREFIX TO NUMBERTO EDIT DIRECTORY DATATO DELETE ALL DATATO DELETE A SPECIFIC DATA
ADD NEW DATA
P 1: While indicating the current time on LCD,press key to open the Menu screen.OR
Press (Directory) key. The Directory sshown at STEP 3 can be directly displaye
STEP 2: Select Directory.Select an item by either of the following operati• Highlight an item by using , and then pre
or OK soft key.• Press key.
e: A maximum of 500 entries can be registered inDirectory.
DT730
Menu
Note: Directory feature is available for DT730only. DT710/DT330/DT310 Series does nport the directory feature.
Note: On the Menu screen, use or sofmove the cursor up/down a line.
DT730 Series
Directory 3
[Menu] History
Tool
1 2
3
[Menu] History
Tool
1 2 Directory Press Down-Cursor ke
Currently Selected Ite
OK Back
OK Back
2
2
STE
STE
ons.ss ,
tory.g the
Not
176
P 3: Select Personal.Select an item by either of the following operations.• Highlight an item by using , and then press ,
or OK soft key.• Press key.
P 4: Select Edit.Select an item by either of the following operations.• Highlight an item by using , and then press ,
or OK soft key.
• Press key.
STEP 5: Select Name.Select an item by either of the following operati• Highlight an item by using , and then pre
or OK soft key.• Press key.
STEP 6: Enter a name to be registered in direcEnter a name by using digits keys. After enterin
e: When using Phonebook feature is disabled, thisscreen will not be displayed. In that case, skipthis step.
History12
Tool
[Menu]
3456#0
Call Func. SettingPresenceFavoriteConfig
Directory
OKBack
1
1
12
[Directory]
3 CorporateSystem
OKBack
Personal
2
2
Search12
Group Setting
[Directory]
340
Own NumberDelete All
Edit
OKBack
1
1
[Edit]
Name12
[Edit]
345
Name
OKBack
67890Save
Gr GroupTel #1
Company NameRing Tone
Tel #4
Tel #2Tel #3
Illumination0No
STE
ons.ss
OK soft
ons.ss ,
Not
om theee TO
177
name, press or OK soft key.
P 7: The display goes back to the Edit screen. Se-lect Group.Select an item by either of the following operations.• Highlight an item by using , and then press ,
or OK soft key.• Press key.
STEP 8: Select a desired group.Select an item by either of the following operati• Highlight an item by using , and then pre
or OK soft key.• Press - key, and then press or
key.In this example, Colleagues is selected.
STEP 9: Select Tel #1.Select an item by either of the following operati• Highlight an item by using , and then pre
or OK soft key.• Press key.
e: Up to 32 characters can be entered as a name.For details on character entry method, see HOWTO INPUT CHARACTERS in chapter 4.
Input a name.[Name]
OKBackOptionBK
A
2
2
12
[Edit]
345
OKBack
67890Save
Gr
No
Tel #1
Company NameRing Tone
Ken Kobus
Tel #4
Tel #2Tel #3
Illumination0
GroupNote: Each group name can be changed fr
Group Setting screen. For details, sCHANGE GROUP NAME.
0 9
2
12
[Group Select]
3456
20
Colleagues
OKBack
Group 6
FamilyFriends
Default
VIPs
Group 20
:
3
3
STE
STE
Next soft
.s.
ss
r OK soft
178
P 10:Enter a telephone number to be registered indirectory.Enter a telephone number by using digits keys. After entering the telephone number, press or Next soft key.
P 11:Select a Category to which the entered tele-phone number belongs. Select an item by either of the following operations.• Highlight an item by using , and then press
or Next soft key.• Press - key, and then press or
key.In this example, Company is selected.
Selectable categories are as follows:
STEP 12:Select either Disable or EnableSelect an item by one of the following operation• Highlight an item by using , and then pre
or OK soft key.• Press or key, and then press o
key.
12
[Edit]
345
OKBack
67890Save
Gr
No
Company NameRing Tone
Ken Kobus
Tel #4
Tel #2Tel #3
Illumination0
ColleaguesTel #1
Input a Telephone number.
[Tel #1]
NextBackBK
1
Category ICON
Company
Mobile
Voice Mail
Home
Others
0 5
1
12
[Category]
345
Company
NextPrev
HomeOthers
MobileVoice Mail
1 2
1 2
STE
ter enter-key.
Not
Not
a com-r entryERS.
179
A maximum of four telephone numbers can be set to an entry. If Enable is selected here, the tele-phone number which is being edited will be given top priority. In that case, the telephone number is automatically selected when you make a call with-out specifying a specific telephone number.
P 13:The display goes back to the Edit screenagain. Select Company Name.Select an item by either of the following operations.• Highlight an item by using , and then press ,
or OK soft key.• Press key.
STEP 14:Enter a company name.Enter a company name by using digits keys. Afing the company name, press or OK soft
e: A maximum of four telephone numbers can beset to an entry. If two or more telephone numbersare required to be set, set the remaining tele-phone numbers to Tel #2 - Tel #4.
e: If multiple telephone numbers are registered toan entry and Priority Flag is disabled to all of thetelephone numbers, the telephone number set toTel #1 is automatically set as first priority number.
2
[Priority Flag]
OKPrev
112 Enable
Disable
7
7
Note: Up to 32 characters can be entered as pany name. For details on charactemethod, see HOW TO INPUT CHARACT
12
[Edit]
345
OKBack
67890Save
Gr
No
Ring Tone
Ken Kobus
Tel #4
Tel #2Tel #3
Illumination0
Colleagues
Company Name
31300
Input a Company name.[Company Name]
OKBackOptionBK
A
STE
STE
en. Se-
ons.ss ,
to theer Toned “Tele-“Name”“Group”
ge the r “Tele-atic is
d.
O SET
180
P 15:The display goes back to the Edit screen. Se-lect Ring Tone.Select an item by either of the following operations.• Highlight an item by using , and then press ,
or OK soft key.• Press key.
P 16:Select a desired Ringing Tone.
Select an item by either of the following operations.• Highlight an item by using , and then press
or OK soft key.• Press - key, and then press or OK soft
key.
STEP 17:The display goes back to the Edit screlect Illumination.Select an item by either of the following operati• Highlight an item by using , and then pre
or OK soft key.• Press key.
8
8
12
[Edit]
345
OKBack
67890Save
Gr
No
Ken Kobus
Tel #4
Tel #2Tel #3
Illumination0
Colleagues31300
Ring ToneNEC
0 9
Note: You can set ringer tone for calls routedspecified name (calling party) here. Ringtype can be set for “Name”, “Group” anphone set”. The ringer Tone type set for has higher priority than the types set for and “Terminal set”.
Note: Set 2 Default when you don’t want to chanringer tone here. The setting for “Group” ophone set” is applied. Also, when 1 Automset, 3 Tone Type 1 is automatically applie
Note: For details on each ringer tone type, see TRINGER TONE.
12
[Ring Tone]
3
16171819
Automatic
OKBack
Download 1Tone Type 14
DefaultTone Type 1
Download 3Download 2
9
9
STEuted to
llumina-p” andset for set for
ge the up” or uto-d.
181
P 18:Select a desired color of the Call Indicationlamp.Select an item by either of the following operations.• Highlight an item by using , and then press
or OK soft key.• Press - key, and then press or OK soft
key.
12
[Edit]
345
OKBack
67890Save
Gr
No
Ken Kobus
Tel #4
Tel #2Tel #3
0
Colleagues31300
NEC
IlluminationAutomatic
0 9
Note: You can set illumination type for calls rothe specified name (calling party) here. Ition type can be set for “Name”, “Grou“Telephone set”. The illumination type “Name” has higher priority than the types“Group” and “Terminal set”.
Note: Set 2 Default when you don’t want to chanillumination type here. The setting for “Gro“Telephone set” is applied. Also, when 1 Amatic is set, 4 Red is automatically applie
12
[Illumination]
345678
Automatic
OKBack
Yellow
RedGreen
White9
10
DefaultDisable
BlueLight BluePurple
11 Rotation
STE
STE
e Editthe as-
umber:K soft
rectory
ADD
Group
Not
e” will entry.
ill over-pear. Ifs Back, press
30
182
P 19:The display goes back to the Edit screen.Check the memory number assigned to thedirectory data being edited.
P 20:If you need to assign a memory number man-ually, select Memory ID on the screen ofthe previous step, and then enter a desiredmemory number (0 - 499).
Enter a memory number by using digits keys. After entering the memory number, press or OK soft key.
STEP 21:When the display goes back to thscreen, press Save soft key to save signed data.
STEP 22:“The data is registered at memory nXX” is displayed. Press key or Okey. The display returns to the Discreen.
TO CHANGE GROUP NAME
STEP 1: Open the Directory screen (see TONEW DATA).
STEP 2: On the Directory screen, select
e: A memory number is automatically set in ascend-ing numeric order.
12
[Edit]
345
OKBack
67890Save
Gr
No
Ken Kobus
Tel #4
Tel #2Tel #3
0
Colleagues31300
NECAutomaticAutomatic
0
Note: If Name is not entered, “No Input Namappear. Name information is required for a
Note: If a duplicate Memory ID is entered, “It wwrite a data at memory number:XX” will apyou do not overwrite the Memory ID, pressoft key. If you overwrite the Memory ID
or OK soft key.
Input a memory number.[Memory ID]
OKBackBK
1
0-499
DT7
3
STE ons.ss ,
entering
183
Setting.Select an item by either of the following operations.• Highlight an item by using , and then press ,
or OK soft key.• Press key.
P 3: Select a group name to be changed.In this example, Default is selected.Select an item by either of the following operations.• Highlight an item by using , and then press
or OK soft key.• Press key, and then press or OK soft key.
STEP 4: Select Name.Select an item by either of the following operati• Highlight an item by using , and then pre
or OK soft key.• Press key.
STEP 5: Enter a new group name.
Enter a group name by using digits keys. After the group name, press or OK soft key.
3
Search12
[Directory]
340
Own NumberDelete All
Edit
OKBack
Group Setting
1
1
12
[Group]
3456
20
Default
OKBack
Group 6
FamilyFriends
ColleaguesVIPs
:Group 20
1
1
12
[Group Setting]
3Ring Tone
OKBackIllumination
Name
STE
TO
• TSTE
een.ons.ss ,
ons.ss ,
Not
Not
DT7
184
P 6: Display returns to the Group screen. Makesure that the new group name takes effect.
FIND A REGISTERED DATA
o Search by Group NameP 1: Open the Directory screen (see TO ADD
NEW DATA).
STEP 2: Select Search on the Directory scrSelect an item by either of the following operati• Highlight an item by using , and then pre
or OK soft key.• Press key.
STEP 3: Select Group.Select an item by either of the following operati• Highlight an item by using , and then pre
or OK soft key.• Press key.
e: Up to 32 characters can be entered as a group-name. For details on character entry method, seeHOW TO INPUT CHARACTERS in chapter 4.
e: You can set ringer tone ( select 2 Ring Tone)and illumination types ( select 3 Illumination)for calls routed to the specified group here. Ringer tone and illumination types can be set for“Name”, “Group” and “Telephone set”. The ringertone and illumination types set for “Name” havehigher priority than the types set for Group andTelephone set. Also, the ringer tone and illumina-tion types for Group have higher priority than thetypes set for Terminal set.
Input a group name.
[Group Name Set]
OKBackOptionBK
A
Default
30
1
1
12
[Directory]
340
Own NumberDelete All
Edit
OKBack
Group Setting
Search
1
1
12
[Search]
34 Others
Name
OKBack
Tel Number
Group
STE
STE
specificame is
make ing
o data"
ssignedmber isscreen
185
P 4: Select a target group.In this example, Colleagues is selected.Select an item by either of the following operations.• Highlight an item by using , and then press
or OK soft key.• Press key, and then press or OK soft key.
P 5: Select a target name by pressing .
In the following Directory (Name List) screen, you can make a call to the selected party by pressing or Call soft key. If two or more tele-phone numbers are assigned to an entry, a top priority telephone number will be dialed.
STEP 6: To display the detailed data for a name, press Detail soft key while the nhighlighted.
In the following Detail screen, you cana call to the selected number by press
or Call soft key.
2
2
12
[Group]
3456
20
Colleagues
OKBack
Group 6
FamilyFriends
Default
VIPs
Group 20
:
John Smith
[Directory]
CallBackOptionDetailKen KobusJulia
Note: If no entry is set to the selected group, "Nis issued.
Note: If two or more telephone numbers are ato an entry, a top priority telephone nuautomatically selected when the Detail appears.
12
[Detail]
34567890
Gr
NoCallBack
Tel #4Tel #3
0
Colleagues
NECAutomaticAutomatic
Ken Kobus
0800XXXXXX31300
• T
STE
STE
STE
soft
(Up/
reen, by re tele-a top
se andsystemd "kenaracterdminis-
search-
nd, you
entered
a com-r entryERS.
186
o Search by Name
P 1: Open the Directory screen (see TO ADDNEW DATA).
P 2: Select Search.Select an item by either of the following operations.• Highlight an item by using , and then press ,
or OK soft key.• Press key.
P 3: Select Name.Select an item by either of the following operations.• Highlight an item by using , and then press ,
or OK soft key.• Press key.
STEP 4: Enter a target name. After entering the name, Press or OKkey.
STEP 5: Select a target name by pressing down-cursor).In the following Directory (Name List) scyou can make a call to the selected party pressing or Call soft key. If two or mophone numbers are assigned to an entry, priority telephone number will be dialed.
1
1
12
[Directory]
340
Own NumberDelete All
Edit
OKBack
Group Setting
Search
2
2
12
[Search]
34 Others
OKBack
Tel Number
GroupName
Note: A distinction is made between upper calower case characters, according as the settings. For example, "Ken Kobus" ankobus" are distinguished as different chstrings. For details, contact the System Atorator.
Note: A blank space is also distinguished while ing database for a name.
Note: Even if the name is not entered to the ecan search for a name.
Note: If there is no entry corresponding to the name, "No data" is issued.
Note: Up to 32 characters can be entered as pany name. For details on charactemethod, see HOW TO INPUT CHARACT
Input a name.[Name]
OKBackOptionBK
A
STE
Not
187
P 6: To display the detailed data for a specificname, press Detail soft key while the name ishighlighted.
In the following Detail screen, you can make a call to the selected number by pressing or Call soft key.
e: If two or more telephone numbers are assignedto an entry, a top priority telephone number isautomatically selected when the Detail screenappears.
[Directory]
CallBackOptionDetail
Abe Ichiro
Abe SabroAbe Kentaro
12
[Detail]
34567890
Gr
NoCallBack
Tel #4Tel #3
0
Colleagues
NECAutomaticAutomatic
0800XXXXXX31300
Abe Kentaro
• TSTE
STE
STE
STE
K soft
.reen, by re tele-a top
ered toumber.
entered.
188
o Search by Telephone NumberP 1: Open the Directory screen (see TO ADD
NEW DATA).
P 2: Select Search.Select an item by either of the following operations.• Highlight an item by using , and then press ,
or OK soft key.• Press key.
P 3: Select Tel Number.Select an item by either of the following operations.• Highlight an item by using , and then press ,
or OK soft key.• Press key.
P 4: Enter a target telephone number.
After entering the number, press or Okey.
STEP 5: Select a target name by pressing In the following Directory (Name List) scyou can make a call to the selected party pressing or Call soft key. If two or mophone numbers are assigned to an entry, priority telephone number will be dialed.
1
1
12
[Directory]
340
Own NumberDelete All
Edit
OKBack
Group Setting
Search
3
3
12
[Search]
34 Others
OKBack
Tel Number
GroupName
Note: Even if the telephone number is not entthe end, you can search for a telephone n
Note: If there is no entry corresponding to the number, "No data" is issued on the screen
Input a Telephone number.[Tel Number]
OKBackBK
1
[Directory]
CallBackOptionDetail
Abe Ichiro
Abe SabroAbe Kentaro
STE
Not
189
P 6: To display the detailed data for a specificname, press Detail soft key while the name ishighlighted.
In the following Detail screen, you can make a call to the selected number by pressing or Call soft key.
e: If two or more telephone numbers are assignedto an entry, a top priority telephone number isautomatically selected when the Detail screenappears.
12
[Detail]
34567890
Gr
NoCallBack
Tel #4Tel #3
0
Colleagues
NECAutomaticAutomatic
0800XXXXXX31300
Abe Kentaro
• TSTE
STE
STE
ons.ss ,
or
ed, with r clos-
(Up/
reen, by re tele-
190
o Search by Memory IDP 1: Open the Directory screen (see TO ADD
NEW DATA).
P 2: Select Search.Select an item by either of the following operations.• Highlight an item by using , and then press ,
or OK soft key.• Press key.
P 3: Select Others.Select an item by either of the following operations.• Highlight an item by using , and then press ,
or OK soft key.• Press key.
STEP 4: Select Memory ID.Select an item by either of the following operati• Highlight an item by using , and then pre
or OK soft key.• Press key.
STEP 5: Enter a memory number (0-499). After entering the memory number, press OK soft key.
The list of memory numbers will be displaythe entered memory number or the numbeest to the entered number in front.
STEP 6: Select a target name by pressing down-cursor).In the following Directory (Name List) scyou can make a call to the selected party pressing or Call soft key. If two or mo
1
1
12
[Directory]
340
Own NumberDelete All
Edit
OKBack
Group Setting
Search
4
4
12
[Search]
34
OKBack
Tel Number
GroupName
Others
1
1
12
[Others]
34
OKBackAlphabet
CategoryCompany
Memory ID
Input a Memory number.[Memory ID]
OKBackBK
1
STE
Not
Not
191
phone numbers are assigned to an entry, a top priority telephone number will be dialed.
P 7: To display the detailed data for a specificname, press Detail soft key while the name ishighlighted.
In the following Detail screen, you can make a call to the selected number by pressing or Call soft key.
e: If no data exists in Directory, "No data" is issuedon the screen.
e: If two or more telephone numbers are assignedto an entry, a top priority telephone number isautomatically selected when the Detail screenappears.
[Directory]
CallBackOptionDetail
Abe SabroAbe Kentaro
12
[Detail]
34567890
Gr
NoCallBack
Tel #4Tel #3
0
Colleagues
NECAutomaticAutomatic
0800XXXXXX31300
Abe Kentaro
• TSTE
STE
STE
s.ss ,
s.ss
ft key.
.reen, by re tele-
192
o Search by CategoryP 1: Open the Directory screen (see TO ADD
NEW DATA).
P 2: Select Search.Select an item by either of the following operations.• Highlight an item by using , and then press ,
or OK soft key.• Press key.
P 3: Select Others.Select an item by either of the following operations.• Highlight an item by using , and then press ,
or OK soft key.• Press key.
STEP 4: Select Category.Select an item by one of the following operation• Highlight an item by using , and then pre
or OK soft key.• Press key.
STEP 5: Select a desired category.In this example, Company is selected.Select an item by one of the following operation• Highlight an item by using , and then pre
or OK soft key.• Press key, and then press or OK so
STEP 6: Select a target name by pressing In the following Directory (Name List) scyou can make a call to the selected party pressing or Call soft key. If two or mo
1
1
12
[Directory]
340
Own NumberDelete All
Edit
OKBack
Group Setting
Search
4
4
12
[Search]
34
OKBack
Tel Number
GroupName
Others
2
2
12
[Others]
34
OKBackAlphabetCompany
Memory ID
Category
1
1
12
[Category]
345
Company
OKBack
HomeEtc
MobileVoice Mail
STE
Not
Not
193
phone numbers are assigned to an entry, a top priority telephone number will be dialed.
P 7: To display the detailed data for a specificname, press Detail soft key while the name ishighlighted.
In the following Detail screen, you can make a call to the selected number by pressing or Call soft key.
e: If there is no entry corresponding to the selectedcategory, "No data" is issued on the screen.
e: If two or more telephone numbers are assignedto an entry, a top priority telephone number isautomatically selected when the Detail screenappears.
[Directory]
CallBackOptionDetail
Abe SabroAbe Kentaro
Abe Taro
12
[Detail]
34567890
Gr
NoCallBack
Tel #4Tel #3
0
Colleagues
NECAutomaticAutomatic
0800XXXXXX31300
Abe Kentaro
• TSTE
STE
STE
ons.ss ,
key.
se and, "Ken as dif-
search-
nd, you
a com-r entryERS.
194
o Search by Company NameP 1: Open the Directory screen (see TO ADD
NEW DATA).
P 2: Select Search.Select an item by either of the following operations.• Highlight an item by using , and then press ,
or OK soft key.• Press key.
P 3: Select Others.Select an item by either of the following operations.• Highlight an item by using , and then press ,
or OK soft key.• Press key.
STEP 4: Select Company.Select an item by either of the following operati• Highlight an item by using , and then pre
or OK soft key.• Press key.
STEP 5: Enter a company name.After entering the name, Press or OK soft
1
1
12
[Directory]
340
Own NumberDelete All
Edit
OKBack
Group Setting
Search
4
4
12
[Search]
34
OKBack
Tel Number
GroupName
Others
Note: A distinction is made between upper calower case characters. For exampleKobus" and "ken kobus" are distinguishedferent character strings.
Note: A blank space is also distinguished while ing database for a name.
Note: Even if the name is not entered to the ecan search for a name.
Note: Up to 32 characters can be entered as pany name. For details on charactemethod, see HOW TO INPUT CHARACT
3
3
12
[Others]
34
OKBackAlphabetCompany
Memory ID
Category
Input a Company name.
[Company]
OKBackOptionBK
A
STE
STE
Not
Not
195
P 6: Select a target name by pressing .In the following Directory (Name List) screen, you can make a call to the selected party by pressing or Call soft key. If two or more tele-phone numbers are assigned to an entry, a top priority telephone number will be dialed.
P 7: To display the detailed data for a specificname, press Detail soft key while the name ishighlighted.
In the following Detail screen, you can make a call to the selected number by pressing or Call soft key.
e: If there is no entry corresponding to the selectedCompany, "No data" is issued on the screen.
e: If two or more telephone numbers are assignedto an entry, a top priority telephone number isautomatically selected when the Detail screenappears.
[Directory]
CallBackOptionDetail
Abe SabroAbe Kentaro
Abe Taro
12
[Detail]
34567890
Gr
NoCallBack
Tel #4Tel #3
0
Colleagues
NECAutomaticAutomatic
0800XXXXXX31300
Abe Kentaro
• TSTE
STE
STE
ons.ss ,
.
s.ss
ft key.
196
o Search by AlphabetP 1: Open the Directory screen (see TO ADD
NEW DATA).
P 2: Select Search.Select an item by either of the following operations.• Highlight an item by using , and then press ,
or OK soft key.• Press key.
P 3: Select Others.Select an item by either of the following operations.• Highlight an item by using , and then press ,
or OK soft key.• Press key.
STEP 4: Select Alphabet.Select an item by either of the following operati• Highlight an item by using , and then pre
or OK soft key.• Press key.
STEP 5: Select a desired group of alphabetsIn this example, ABC is selected.Select an item by one of the following operation• Highlight an item by using , and then pre
or OK soft key.• Press key, and then press or OK so
1
1
12
[Directory]
340
Own NumberDelete All
Edit
OKBack
Group Setting
Search
4
4
12
[Search]
34
OKBack
Tel Number
GroupName
Others
4
4
12
[Others]
34
OKBack
Company
Memory IDCategory
Alphabet
1
0
STE
specificame is
ke a call r Call
Not
roup ofen.
ssignedmber isscreen
197
P 6: Select a target name by pressing .In the following Directory (Name List) screen, you can make a call to the selected party by pressing or Call soft key. If two or more tele-phone numbers are assigned to an entry, a top priority telephone number will be dialed.
STEP 7: To display the detailed data for a name, press Detail soft key while the nhighlighted.
In the following Detail screen, you can mato the selected number by pressing osoft key.
e: Select * Others to find names which begin with acharacter other than alphabet such as numericsor symbols.
12
[Alphabet]
345678
OKBack
PQRS
JKLMND
All*#
DEFGHI
TUVWXYZOthers
ABC
[Directory]
CallBackOptionDetail
Abe SabroAbe Kentaro
Abe Taro
Note: If there is no entry corresponding to the galphabets, "No data" is issued on the scre
Note: If two or more telephone numbers are ato an entry, a top priority telephone nuautomatically selected when the Detail appears.
12
[Detail]
34567890
Gr
NoCallBack
Tel #4Tel #3
0
Colleagues
NECAutomaticAutomatic
0800XXXXXX31300
Abe Kentaro
TO
• T
STE
STE
t party).
d then
sing to make
Not
DT7red to aity tele-
ssignedmber isscreen
198
MAKE A CALL FROM DIRECTORY
o Make a Call from Name List Screen
P 1: Display the Directory (Name List) screen fora target party (see TO FIND A REGISTEREDDATA).
P 2: Select a target name and then make a call.Select a target name by pressing , and then press or Call soft key to make a call to the selected party.
• To Make a Call from Detail Screen
STEP 1: Display the Detail screen for a targe(see TO FIND A REGISTERED DATA
STEP 2: Select a target telephone number anmake a call.Select a target telephone number by pres
, and then press or Call soft key a call to the selected number.
e: While Directory screen is being displayed, youcannot make a call by dialing a telephone num-ber.
30
Abe Jiro
[Directory]
CallBackOptionDetail
Abe Ichiro
Abe Kentaro
Abe Jiro
[Directory]
CallBackOptionDetail
Abe Ichiro
Abe Kentaro
Note: If multiple telephone numbers are registetarget party, a call is made to the first priorphone number.
Note: If two or more telephone numbers are ato an entry, a top priority telephone nuautomatically selected when the Detail appears.
12
[Detail]
34567890
Gr
NoCallBack
Tel #4Tel #3
0
Colleagues
NECAutomaticAutomatic
0800XXXXXX31300
Abe Kentaro
TO
• TWps
STE
STE
ons.ss ,
ons.ss ,
199
ADD PREFIX TO NUMBER
o Set Prefixhen making a call, a prefix can be added to tele-
hone numbers to be dialed. Prefixes need to beet in advance.
P 1: While indicating the current time on LCD,press key to open the Menu screen.
P 2: Select Setting on the Menu screen.Select an item by either of the following operations.• Highlight an item by using , and then press ,
or OK soft key.
• Press key.
STEP 3: Select User Setting.Select an item by either of the following operati• Highlight an item by using , and then pre
or OK soft key.• Press key.
STEP 4: Select Talk.Select an item by either of the following operati• Highlight an item by using , and then pre
or OK soft key.• Press key.
12
[Detail]
34567890
Gr
NoCallBack
Tel #4Tel #3
Colleagues
NECAutomaticAutomatic
Abe Kentaro
0800XXXXXXXX31300
0
DT730
Menu
5
5
History12
Tool
[Menu]
3456#0
Call Func.
PresenceFavoriteConfig
Directory
OKBack
Setting
1
1
12
[Setting]
3OKBack
Data Backup/RestoreDownloadUser Setting
2
2
STE
STE
soft
reen at set, re-, select
be set
cluding
200
P 5: Select Prefix.Select an item by either of the following operations.• Highlight an item by using , and then press ,
or OK soft key.• Press key.
P 6: Select Prefix 1.Select an item by either of the following operations.• Highlight an item by using , and then press ,
or OK soft key.• Press key.
STEP 7: Enter a prefix by using the digit keys. After entering the prefix, press or OKkey.
STEP 8: The display goes back the Prefix scSTEP 5. If multiple prefixes need to bepeat STEP 6 and STEP 7. In that case
Prefix 2 and Prefix 3.
Incoming Call12
Display
[Incoming Call]
345670
Change Password
PeripheralsSetting ResetConfig
OKBack
Security
Talk
5
5
RTP Alarm12
Key Touch Tone
[Talk]
345
Hold Music
OKBack
DTMF Tone
Prefix
1
1
Note: A maximum of 10 digits (0-9, * and #) canas a prefix.
Note: When prefix is added, up to 32 digits inthe prefix can be sent as dial number.
12
[Prefix]
3OKBack
Prefix 3Prefix 2Prefix 1
Input a prefix number.[Prefix 1]
OKBackBK
1
2 3
• T
STE
STE
STE
. Selectt key to
targetDATA).
Not30
201
o Add Prefix When Making A Call
P 1: Display the Name List screen for a targetparty (see TO FIND A REGISTERED DATA).
P 2: Select a target name and display Sub Menu.Select a target name by pressing , and then press key or Option soft key.
P 3: Select Prefix.Select an item by one of the following operations.• Highlight an item by using , and then press ,
or OK soft key.• Press key, and then press , or OK soft
key.
STEP 4: Predetermined prefixes are displayeda prefix and then press or OK sofmake a call.
TO EDIT DIRECTORY DATA STEP 1: Display the Name List screen for a
party (see TO FIND A REGISTERED
e: If multiple telephone numbers are registered to atarget party, a call is made to the first priority tele-phone number.
[Directory]
CallBackOptionDetail
Abe KentaroAbe JiroAbe Ichiro
Menu
[Directory]
CallBackOptionDetailAbe KentaroAbe JiroAbe Ichiro
1
1
12
SubMenu
3
OKCancel
Delete AllDelete OnePrefix
4 Edit
12
[Prefix]
3CallBack
187186184
DT7
[Directory]
CallBackOptionDetail
Abe KentaroAbe JiroAbe Ichiro
STE
STE
STE
ADD
ons.ss ,
202
P 2: Select a target name and display Sub Menu.Select a target name by pressing , and then press key or Option soft key.
P 3: Select Edit.Select an item by one of the following operations.• Highlight an item by using , and then press ,
or OK soft key.• Press key, and then press , or OK soft
key.
P 4: On the Edit screen, the detailed data for theselected name is displayed. Modify the nec-essary data by referring to TO ADD NEW DA-TA. After the data modification is complete, press Save soft key on the Edit screen.
TO DELETE ALL DATA STEP 1: Open the Directory screen (see TO
NEW DATA).
STEP 2: Select Delete All.Select an item by either of the following operati• Highlight an item by using , and then pre
or OK soft key.• Press key.
Menu
[Directory]
CallBackOptionDetail
Abe KentaroAbe JiroAbe Ichiro
4
4
12
SubMenu
3
OKCancel
Delete AllDelete OnePrefix
4 Edit
12
[Edit]
34567890
Gr
NoOKBack
Tel #4Tel #3
0Save
31300
NECAutomaticAutomatic
Abe Kentaro
0800XXXXXX
Colleagues
DT730
0
0
STE
STE
targetDATA).
lay Sub
d then
ons.ss ,
OK soft
Not
T730
203
P 3: Press or OK soft key to delete all the da-ta.
P 4: After all the directory data is deleted, the dis-play changes as follows:
STEP 5: Press or OK soft key.
TO DELETE A SPECIFIC DATA
STEP 1: Display the Name List screen for aparty (see TO FIND A REGISTERED
STEP 2: Select a name to be deleted and dispMenu.
Select a target name by pressing , anpress key or Option soft key.
STEP 3: Select Delete One.Select an item by either of the following operati• Highlight an item by using , and then pre
or OK soft key.• Press key, and then press , or
key
e: To cancel the data deletion, press or Backsoft key.
12
[Directory]
340
Own Number
Edit
OKBack
Group Setting
Search
Delete All
Delete All Directory?
[Directory]
OKBack
Deleted.[Directory]
OK
D
[Directory]
CallBackOptionDetail
Abe ShintaroAbe JiroAbe Ichiro
Menu
[Directory]
CallBackOptionDetailAbe ShintaroAbe JiroAbe Ichiro
2
2
STE
STE
Not
204
P 4: The following confirmation message appears.Press or OK soft key to delete the appro-priate directory data.
P 5: After the appropriate directory data is delet-ed, the display changes as follows:
STEP 6: Press or OK soft key.
e: To cancel the data deletion, press or Cancelsoft key.
12
SubMenu
3
OKCancel
Delete All
Prefix
4 Edit
Delete One
Delete this entry?
[Directory]
OKBack
Deleted.[Directory]
OK
7This Seriesimp
Call to 50Seriereco
•••
•
••
••••
ctory asd when historyackup/
L SET-L SET-
emorynebookebook)
205
. CALL HISTORY OPERATION
chapter explains the Call History feature of DTs. By using Call History, you can make a call withle operation.
History feature allows the telephone to register up records (for DT730 Series)/10 records (for DT330s) into its memory. If exceeding 50 records/10
rds, a record will be deleted in order of occurrence.
FOR DT730 SERIES
TO VIEW CALL HISTORYTO MAKE A CALL FROM CALL HISTORYTO ADD CALL HISTORY DATA TO DIRECTORYTO EDIT DIRECTORY DATA FROM CALL HISTORYTO DELETE ALL DATATO DELETE A SPECIFIC DATA
FOR DT330 SERIES
TO VIEW CALL HISTORYTO MAKE A CALL FROM CALL HISTORYTO DELETE ALL DATATO DELETE A SPECIFIC DATA
Note: Register call history data to Personal Direnecessary. Call History data will be clearepowering off the telephone. However, calldata can be backed up to your PC. About BRestore, see “TO BACKUP PERSONATINGS” or “TO RESTORE PERSONATINGS” in “3.TERMINAL SETUP”.
Note: The call history data that is stored in the mof each telephone cannot be added to Pho(both System Phonebook and Local Phoncontrolled by the system.
7.1
TO
STE
STE
ons.ss ,
Not
red
calls.d and
206
FOR DT730 SERIES
VIEW CALL HISTORY
P 1: While indicating the current time on LCD,press key to open the Menu screen.
P 2: Select History.Select an item by either of the following operations.• Highlight an item by using , and then press ,
or OK soft key.• Press key.
STEP 3: Select a kind of calls. In this example, Incoming is selected.Select an item by either of the following operati• Highlight an item by using , and then pre
or OK soft key.• Press key.
e: This feature is available for DT730 Series. DT710Series does not support this feature.The following are examples of LCD display ofDT730 Series.
DT730
Menu
DT730 Series
1 History 2 Directory 3 Tool
[Menu]
Back OK
1
1
Item Description
Missed Display the history of unansweincoming calls.
Outgoing Display the history of outgoing
Incoming Display the history of answereunanswered incoming calls.
12
Tool
[Menu]
3456#0
Call Func. SettingPresenceFavoriteConfig
Directory
OKBack
History
3
3
12
[History]
34 Delete All
Outgoing
OKBack
Missed
Incoming
STE
Not
Not
Not
Not
207
P 4: The history data of the last received call is displayed.If two or more records exist, use or soft key to display the next/former records.
e: For unanswered incoming calls, will be dis-played on the left of the name.
e: If you make/answer a call to/from the telephonenumber which is registered to Personal Directory,the corresponding name will be displayed as callhistory data.
e: If there is no history data, "No data" will be dis-played on LCD.
e: To go back to former menu (STEP 3), press or Back soft key.
1
[Incoming]
OptionBack
12/JUL/2010 (MON) 10:00Ken Kobus
7205
TOTO
(CASSTE
STE
(CASSTE
or Op-ub
g ,
Not
a prefixt case,ated atscreen. to beneed tof prefix,apter 6
208
MAKE A CALL FROM CALL HIS-RY
E 1)P 1: Display call history data of a target telephone
number (see TO VIEW CALL HISTORY).
The following is an example when a history data ofIncoming Calls is displayed.
P 2: Press key to make a call to the telephone number.
E 2)P 1: Display call history data of a target telephone
number (see TO VIEW CALL HISTORY).
The following is an example when a history data ofIncoming Calls is displayed.
STEP 2: On the above screen, press keytion soft key to display the following SMenu.
STEP 3: To make a call, select Call (by usinor pressing key) and then press or OK soft key.
e: While the history data is displayed, you cannotmake a call by dialing a telephone number.
DT730
2
[Incoming]
OptionBack
12/JUL/2010 (MON) 9:58Abe Kentaro
7207
Note: When making a call from Call History, can be added to the dial number. In thaselect 3 Prefix on the SubMenu (indicSTEP 2 of CASE 2) to display the Prefix On the Prefix screen, choose a prefixadded to the dial number. Also, prefixes be set in advance. For details on setting osee TO ADD PREFIX TO NUMBER in ChDirectory Operation.
2
[Incoming]
OptionBack
12/JUL/2010 (MON) 9:58Abe KentaroTel: 7207
Menu
12
SubMenu
3
OKBack
PrefixDirectory AddCall
4 Delete One5 Delete All
11
TODIR
STE
STE
ons.ss ,
ons.ss
soft key.
209
ADD CALL HISTORY DATA TO ECTORY
P 1: Display call history data of a target telephonenumber (see TO VIEW CALL HISTORY).
The following is an example when history data ofan Incoming Call is displayed.
Press key or Option soft key whiledisplaying the call history data for the targettelephone number.
P 2: The following Sub Menu is displayed. Select Directory Add.
Select an item by either of the following operations.• Highlight an item by using , and then press ,
or OK soft key.• Press key, and then press , or OK soft
key
STEP 3: Select New.Select an item by either of the following operati• Highlight an item by using , and then pre
or OK soft key.• Press key.
STEP 4: Select a category.In this example, Company is selected.Select an item by either of the following operati• Highlight an item by using , and then pre
or Next soft key.• Press key, and then press or Next
DT730
1
[Incoming]
OptionBack
12/JUL/2010 (MON) 11:0031312
31312
Menu
2
2
12
SubMenu
3
OKBack
Prefix
Call
4 Delete One5 Delete All
Directory Add
1
1
12
[Directory Edit]
Addition
OKBack
New
1
1
STEP
OK soft
. .
r 6 Di-d data.
in thebe dis-
210
Selectable categories are as follows:
5: Select either Disable or Enable.A maximum of four telephone numbers can be set to an entry. If Enable is selected here, the tele-phone number which is being edited will be given top priority. In that case, the telephone number is automatically selected when you make a call with-out specifying a specific telephone number.
Select an item by either of the following operations.• Highlight an item by using , and then press
or OK soft key.
• Press or key, and then press orkey.
STEP 6: The following Edit screen is displayed“31312” has been registered to Tel #1
See “TO ADD NEW DATA” in Chapterectory Operation, and register detaile(such as name, group, etc) to directory
Category ICON
Company
Mobile
Voice Mail
Home
Others
12
[Category]
345
Company
NextBackOthersHome
MobileVoice Mail
1 2
2
Note: If the corresponding data is not stored directory, only the telephone number will played as Tel #1.
1 2
12
[Priority Flag]
Disable
OKPrev
Enable
12
[Edit]
34567890
Gr
NoOKBack
Tel #4
Tel #2Tel #3
0Save
Group
Company Name
31312
Ring ToneIllumination
Name
Not
211
e: If the corresponding data has already stored inthe directory, the detailed data (such as namegroup, etc.) is displayed.
TOCA
STE
STE
ons.ss ,
for the
ons.ss ,
212
EDIT DIRECTORY DATA FROM LL HISTORY
P 1: Display call history data of a target telephonenumber (see TO VIEW CALL HISTORY).
The following is an example when history data ofan Incoming Call is displayed.
Press key or Option soft key whiledisplaying the call history data for the targettelephone number.
P 2: The following Sub Menu is displayed. Select Directory Add.
Select an item by either of the following operations.• Highlight an item by using , and then press ,
or OK soft key.• Press key, and then press , or OK soft
key
STEP 3: Select Addition.Select an item by either of the following operati• Highlight an item by using , and then pre
or OK soft key.• Press key.
STEP 4: Select a search method.
See TO FIND A REGISTERED DATAprocedure of the searching method.
In this example, Group is selected.Select an item by either of the following operati• Highlight an item by using , and then pre
or OK soft key.• Press key.
DT730
1
[Incoming]
OptionBack
12/JUL/2010 (MON) 10:007205
7205
Menu
2
2
12
SubMenu
3
OKBack
Prefix
Call
4 Delete One5 Delete All
Directory Add
2
2
12
[Directory Edit]
OKBack
NewAddition
1
1
STE
STE
exam-
ons.ss
OK soft
ata" will
numbertered toXXXX”
213
P 5: Select a group. In this example, Colleagues is selected.Select an item by either of the following operations.• Highlight an item by using , and then press
or OK soft key.• Press key, and then press OK soft key
P 6: The names belonging to Colleagues are dis-played as the following example.
Select a name and then press or OK softkey.
STEP 7: Select a registration destination. In thisple, “7205” will be added to Tel #2.
Select an item by either of the following operati• Highlight an item by using , and then pre
or OK soft key.• Press - key, and then press or
key.
12
[Directory Search]
34
Group
OKBackOthers
NameTel Number
2
2
12
[Group]
3456
20
Colleagues
OKBack
Group 6
FamilyFriends
Default
VIPs
Group 20
:
Note: If there is no corresponding data, "No dbe displayed on LCD.
Note: In this example, a mobile telephone “0800XXXXXXX” has already been regisTel #1. If you select Tel #1 here, “0800XXXwill be overwritten with “7205”.
Kimura
[Directory]
OKBack
Abe Kentaro
Ken Kobus
1 4
12
[Directory]
34
Tel #1:
OKBackTel #4:
Tel #2:Tel #3:
0800XXXXXXX
STEP
STEP
of Di-Tel #2.pera-
214
8: Select a Category to which the telephone number belongs.In this example, Company is selected.Select an item by either of the following operations.• Highlight an item by using , and then press
or OK soft key.• Press key, and then press or OK soft key.
9: Select either Disable or Enable.A maximum of four telephone numbers can be set to an entry. If Enable is selected here, the tele-phone number which is being edited will be given top priority. In that case, the telephone number is automatically selected when you make a call with-out specifying a specific telephone number.Select an item by either of the following operations.• Highlight an item by using , and then press
or OK soft key.• Press or key, and then press or OK soft
key.
STEP 10:The display moves to the Edit screen rectory. “7205” has been registered to See TO EDIT DIRECTORY DATA in Directory Otion, and edit the data as necessary.
1
1
12
[Category]
345
Company
NextBackOthersHome
MobileVoice Mail
1 2
2
1 2
12
[Priority Flag]
Disable
OKPrev
Enable
12
[Edit]
34567890
Gr
NoOKBack
Tel #4
7205Tel #3
0Save
0800XXXXXXX
Ken KobusColleagues
NECAutomaticBlue
TO
STE
STE
STE
pears. the da-
play soft
r Back
215
DELETE ALL DATA
P 1: While indicating the current time on LCD,press key to open the Menu screen.
P 2: Select History.Select an item by either of the following operations.• Highlight an item by using , and then press ,
or OK soft key.• Press key.
P 3: Select All Delete.Select an item by either of the following operations.• Highlight an item by using , and then press ,
or OK soft key.• Press key.
STEP 4: The following confirmation message apPress or OK soft key to delete allta.
STEP 5: After all history data is deleted, the dischanges as follows. Press or OKkey.
DT730
Menu
1
1
12
Tool
[Menu]
3456#0
Call Func. SettingPresenceFavoriteConfig
Directory
OKBack
History
4
4
Note: To cancel the data deletion, press osoft key.
12
[History]
34
Outgoing
OKBack
Incoming
Missed
Delete All
[Delete All]
Delete All Histories?
OKBack
[Delete History]
All History data has been deleted.
OK
TO
STE
STE
pears. appro-
coming
r Back
216
DELETE A SPECIFIC DATA
P 1: Display call history data of a target telephonenumber referring to TO VIEW CALL HISTO-RY. The following is an example when a history data of Incoming Calls is displayed.
Press key or Option soft key whiledisplaying the call history data for the targettelephone number.
P 2: The following Sub Menu is displayed. Select Delete One.
Select an item by either of the following operations.• Highlight an item by using , and then press ,
or OK soft key.• Press key, and then press , or OK soft
key.
STEP 3: The following confirmation message apPress or OK soft key to delete thepriate history data.
DT730
1
[Incoming]
OptionBack
12/JUL/2010 (MON) 11:00Ken Kobus
31310
Menu
4
4
Note: By selecting 5 Delete All, all records of InCall can be deleted.
Note: To cancel the data deletion, press osoft key.
12
SubMenu
3
OKBack
Prefix
Call
45 Delete All
Directory Add
Delete One
[Incoming]
OKBack
Delete this entry?
STE
217
P 4: After the appropriate call history data is delet-ed, the display changes as follows. Press
or OK soft key.
OK
Deleted.[Incoming]
7.2
TO
• TO
STE
STE
d. ons.ss , Not
calls. calls.
cate the ber of
s
218
FOR DT330 SERIES
VIEW CALL HISTORY
O VIEW DATA OF INCOMING CALL/UTGOING CALL
P 1: While indicating the current time on LCD,press key to open the Menu screen.
P 2: Select Call History.Select an item by either of the following operations.• Highlight an item by using , and then press ,
or OK soft key.• Press key.
STEP 3: Select a kind of calls. In this example, Incoming Calls is selecteSelect an item by either of the following operati• Highlight an item by using , and then pre
or OK soft key.• Press key.
e: This feature is DT730 Series and DT330 Series.The following are examples of LCD displays ofDT730 Series and DT330 Series.
DT330
Menu
DT330 Series
1 Call History 2 Directory
[Menu]
Back OK
1
1
Item DescriptionIncoming Calls To view the history of incomingOutgoing Calls To view the history of outgoing
12
[Menu]
3OKBack
SettingsDirectoryCall History
1
1
12
[Call History]
OKBackOutgoing Calls:Incoming Calls: 3
7
DelIndinumcall
STE
STE
Not
Not
Not
ey. Foritching
cannot
s Back
is not phoneyed on
219
P 4: The history data of the last received call is displayed. If name information of the caller exists, the name is displayed as follows:
P 5: To view the telephone number of the caller, press .
e: There are two types of incoming call: AnsweredCall and Missed Call. When history data ofmissed calls is displayed on the screen, appears on the top line of the screen.
e: If two or more records exist, use to displaythe next/former records (or pressing an appropri-ate digit key). For example, press “0” key to dis-play the tenth record.
e: If no history data is saved, "No data" will be dis-played on LCD.
[Incoming Calls]
OKBackDelKen Kobus
10. 12 JUL 13:17
[Incoming Calls]
OKBackDel0901234567810. 12 JUL 13:17
Note: To go back to name display, press kthe telephone without the cursor key, swbetween “name” and “telephone number”be performed.
Note: To go back to former menu (STEP 3), pressoft key.
Note: If the telephone number of the callerreceived (due to Caller ID blocking, publicor out of area, etc.), “Private” is displaLCD.
• T
STE
STE
all is aller s:
Not
Not
to dis-ing an “0” key
s Back
is not phoneyed on
220
O VIEW DATA OF MISSED CALL ONLY
P 1: While indicating the current time on LCD,press key to open Shortcut screen.
P 2: Select Missed Calls.Select an item by either of the following operations.• Highlight an item by using , and then press ,
or OK soft key.• Press key.
STEP 3: The history data of the last received cdisplayed. If name information of the cexists, the name is displayed as follow
e: indicate that the telephone has received amissed call.
indicate that the telephone has received avoice mail.
e: When voice mail service is not used, “ -----------” is displayed instead of “ Voice Mail”.
19:20 PM MON 12 JUL 2010
1
1
12
[Shortcut]
3OKBack
---------------------------Voice MailMissed Calls : 2
22
Note: If two or more records exist, use keyplay the next/former records (or pressappropriate digit key). For example, pressto display the tenth record.
Note: To go back to former menu (STEP 3), pressoft key.
Note: If the telephone number of the callerreceived (due to Caller ID blocking, publicor out of area, etc.), “Private” is displaLCD.
[Incoming Calls]
OKBackDel.Ken Kobus10. 12 JUL 13:17
TOTO
STE
STE
Not
221
MAKE A CALL FROM CALL HIS-RY
P 1: Display the call history data of the target tele-phone number (see TO VIEW CALL HISTO-RY).
The following is an example when the history dataof an incoming call is displayed.
P 2: Press key while the history data for the target telephone number is displayed on LCD.
e: While the history data is displayed, you cannotmake a call by dialing a telephone number.
DT330
[Incoming Calls]
OKBackDelKen Kobus10. 12 JUL 13:17
TO
STE
STE
es as
the his-
Inc
Ou
r Back
222
DELETE ALL DATA
P 1: Select Call History on the Menu screen.Select an item by either of the following operations.• Highlight an item by using , and then press ,
or OK soft key.• Press key.
P 2: Select a kind of calls. In this example, Incoming Calls is selected. Select an item by either of the following operations.• Highlight an item by using , and then press ,
or OK soft key.• Press key.
STEP 3: Press Del soft key. The display changfollows:
STEP 4: Press or OK soft key to delete all tory data of selected call type.
Item Description
oming Calls To delete all the history data of incoming calls.
tgoing Calls To delete all the history data of outgoing calls.
DT330
1
1
12
[Menu]
3OKBack
SettingsDirectoryCall History
1
1
12
[Call History]
OKBackOutgoing Calls:Incoming Calls: 3
7
DelIndicate the number of calls
Note: To cancel the data deletion, press osoft key.
Delete All
Back
[Incoming Calls]
OK
TO
STE
STE
STE
Not
223
DELETE A SPECIFIC DATA
P 1: Display the call history data which you want todelete (see TO VIEW CALL HISTORY). Thefollowing is an example when the history dataof an incoming call is displayed.
P 2: Press Del soft key. The display changes as follows:
P 3: Press or OK soft key to delete the select-ed history data.
e: To cancel the data deletion, press or Backsoft key.
DT330
[Incoming Calls]
OKBackDelKen Kobus10. 12 JUL 13:17
Delete One
Back
[Incoming Calls]
OK
224
This page is for your notes.
8TECThe
E
Disp one
Disp -
Char -
Prog eys
Fixed Keys
Back
Soft one
Call
Hand uplex)
Head
Pow
Adap
Colo
Dime [mm]
Weig 0 kg
NN
225
. SPECIFICATIONS
HNICAL SPECIFICATIONSfollowing shows the technical specifications of DT 300 Series.
Telephone Type 8LD 32D 24D/12D 6DE 2
lay (LCD) 87 43mm, 168 58 dot matrix, 28-digit 4-line* 8LD has two LCDs.
90 28mm, 24-digit 3-line N
lay Color Monochrome (with no shades of gray)
acter on LCD Characters supported by Multilingual Display (Note 1)
rammable Key
Key data is displayed on LCD.
32 (8 X 4) Keys [2-color (red and green)
LED]
32/24/12 Keys [2-color (red and green) LED] 6 Keys [2-color (red and green) LED]
2 K
Feature Key 10 keys (with Menu/Cursor button) (Note 2) 12 Keys 12
light Display and Digit Key (lit for 10 seconds when operating)*For 32D/24D/12D, Display Backlight is optional. None
Key 4 Keys N
History Outgoing Call: 10 record, Incoming Call: 10 records None
s-free Standard equipment (Full-duplex) Standard equipment (Half-d
set Available Not available
er Consumption 2.2 [W] 1.2 [W]
ter (optional) Recording Unit (ADA)/Analog Port Unit (APR)/Wall-mounting kit (WM)/Digit-key Set Unit/Key kit/Side panel Side panel
r Black/White Black
nsion (WDH) 179(W) 248.7(D) 111.7(H) [mm] 179(W) 257(D) 112(H)
ht 1.3 kg 1.2 kg 1.2 kg 1.1 kg 1.
ote 1: 6DE does not support the display in Russian. ote 2: Optional Retro key kit supplies 12 Fixed Feature Keys
The
T
Disp
Disp
Prog s
Fixe ys
Bac
Soft
Dire
Call
XML
Han x)
Hea
LAN
Voic
IP A
QoS
VLA
Sec
Pow
Pow ]
Dow n Hold
Ada ting kitnel
Colo
Dim ]
Wei g
N
226
following shows the technical specifications of DT 700 Series.
elephone Type 8LD 32D 24D/12D 6DE 2E
lay (LCD) 87 43mm, 224 96 dot matrix, 28-digit 5-line* 8LD has two LCDs.
90 28mm, 168 41 dot matrix,
24-digit 3-lineNone
lay Color Gray scale (with 8 shades of gray) Monochrome (with no shades of gray) -
rammable KeyKey data is displayed on
LCD.32 (8 X 4) Keys [2-color
(red and green) LED]32/24/12 Keys [2-color (red and green) LED] 6 Keys [2-color (red
and green) LED] 2 Key
d Feature Key 11 keys (with Menu/Cursor/Security button)(Note 1) 10 Keys(Note 1) 12 Ke
klight Display and Digit Key (lit for 10 seconds when operating) None
Key 4 Keys None
ctory 500 records None
History Outgoing Call: 50 record, Incoming Call: 50 records None
Browser Available None
ds-free Standard equipment (Full-duplex), Wide-band Standard equipment (Full-duple
dset Available Not available
Interface 2-port, 10BASE-T/100BASE-TX, Full-duplex/Half-duplex, Auto Negotiation /Fixed
e CODEC G.711(µ-law, A-law), G.729a, G.722 G.711(µ-law, A-law), G.729a
ddress Setting Sets via DHCP server/Sets Directly
ToS (IP Precedence, Diffserv)
N Tag VLAN (IEEE802.1Q/p)
urity IEEE802.1x authentication (EAP-MD5, EAPOL Forwarding), SIP&RTP Encryption
er Supply Center Power Supply = IEEE802.3af, Local Power Supply = AC adapter (AC-2R UNIT: optional)
er Consumption PoE=6.24 [W]/Local=5.64 [W] PoE=3.264 [W]/Local=2.928 [W
nload Program/Configuration data/Ringing Tone/Music on Hold/Directory data Program/Configuration data/Music o
pter (Optional) Recording Unit/Wall-mounting kit/Digit-key Set Unit/Key kit/Side panel Wall-mounting kit/Digit-key Set Unit/Side panel
Wall-moun/Side pa
r Black/White Black
ension (WDH) 179(W) 264(D) 112(H) [mm]
205.8(W) 258(D)112(H) [mm]
179(W) 258(D) 112(H) [mm] 179(W) 225(D) 112(H) [mm
ght 1.3 kg 1.3 kg 1.2 kg 1.1 kg 1.0 k
ote 1: Optional Retro key kit supplies 12 Fixed Feature Keys
9ME
227
. MENU LIST
NU LIST FOR DT730 SERIES
Menu Item Description
Menu Press key while indicating the current time on LCD.
History To view call history data. Also, you can add the history data to the directory.
Directory To access directory feature. There are the following three types of directory features: Personal Directory, Phonebook and Corporate Directory. This chapter explains the menu list for Personal Directory feature.
Tool Uses when accessing external XML server. For details, please contact the system administrator.
Call Func. Not used.
Setting To access user settings.
Presence Not used.
Favorite Not used.
Config To make the configuration setting of DT Series. For details, please contact the system administrator.
Menu
1
2
3
4
5
6
#
0
M
S
lueS
y
228
enu List For History
ubMenu (Press key or Option soft key while the history data is displayed)
Menu Item Description Default Value
1 History
1 Missed Displays the history of missed calls. You can also make a call from this menu. -
2 Outgoing Displays the history of outgoing calls. You can also make a call from this menu. -
3 Incoming Displays the history of incoming calls. You can also make a call from this menu. -
4 Delete All Deletes all the history data. -
Menu Item Description Default VaubMenu
1 Call Make a call to the currently displayed party. -2 Directory Add Add the currently displayed history data to the personal directory. -
1 New Add call history data to the personal directory. -Category Set Select Company, Mobile, Voice Mail, Home or Others. CompanPriority Flag Select either Enable or Disable. DisableEdit Edit the directory data. -
2 Addition Edit the personal directory data from call history. -Directory Search Search the personal directory. -
Directory Register the telephone number to the searched directory data. -3 Prefix Add Prefix to the telephone number and then make a call. -4 Delete One Delete a specific data. -5 Delete All Delete all history data of a specific call type (“missed”, “outgoing”
or “incoming”)-
1
Menu
M
lue2
y
ws gs)
ws gs)
229
enu List For Directory
Menu Item Description Default Va Directory From Menu screen, select Directory Personal. -
1 Search Search the personal directory. -1 Group Select a group as a search condition. -2 Name Enter the target name and then perform a search. -3 Tel Number Enter the target telephone number and then perform a search. -4 Other Perform a search by one of the following conditions. -
1 Memory ID Enter a memory number. -2 Category Select a category. -3 Company Enter a company name. -4 Alphabet Select a group of alphabets. -
2 Edit Add a new data to the personal directory. -1 Name Enter a name of the target party to be added to the directory. -2 Group Select a group to which the target party belongs. Default3-6 Tel #1-Tel #4 Enter the telephone number. -
Category Set Select Company, Mobile, Voice Mail, Home or Others. CompanPriority Flag Select either Enable or Disable. Disable
7 Company Name Enter the company name of the target party. -
8 Ring Tone Select a ringer tone type per caller.Default (follogroup settin
Note 19 Illumination Select a illumination pattern (color) of the call indication lamp. Default (follo
group settinNote 1
0 Memory ID Enter a memory number to be assigned to the target party. -
2
2 1
Note
M
lue
ws t-
ws t-
lue
3
230
1: For firmware versions earlier than 4.0.0.0, the deafult is "Automatic."
enu List For Tool
Menu Item Description Default Va3 Group Setting Change a group name. -
Group Setting Select a desired group name to be changed. -1 Name Enter a new group name. -2 Ring Tone Select a ringer tone type per group. Default (follo
terminal setings)
Note 13 Illumination Select a illumination pattern (color) of the call indication lamp. Default (follo
terminal setings)
Note 14 Own Number Displays the number of the telephone itself. -0 Delete All Delete all the registered directory data. -
Menu Item Description Default Va
Tool
1 Service Activate XML browser. -
2 IM Not used. -
3
M
e
)
at)
231
enu List For Setting
Menu Item Description Default Valu5 Setting
1 User Setting Make the user setting of DT Series.
1 Incoming Call Settings for incoming call.
1 Ring Volume Not used. -
2 Offhook Ring Enable/Disable Off-hook ringing. Enable
3 Headset Ring Enable/Disable the ringing of headset. Disable
4 Ring Tone Select a ringer tone for External Call and Internal Call.Automatic / Tone Type 1~14 / Download 1~3
Automatic(Tone Type1
5 Illumination Set the illumination pattern for External Call and Internal Call.Automatic / Disable / Red / Green / Blue / Yellow / PurpleLight Blue / White / Rotation
Automatic(Red)
6 Headset Ring Vol-ume
Not used. -
2 Talk Settings for telephone conversation.
1 RTP Alarm Enable/disable RTP alarm. Automatic
2 DTMF Tone Enable/disable DTMF tone. Automatic
3 Key Touch Tone Set key touch tone generated when the digit keys are pressed while the telephone is off-hook. Automatic
4 Hold Music Select a Music on Hold to be heard by DT Series user. Default
5 Prefix Register Prefix number. -
3 Display Settings for LCD display. -
1 Time Format Determines whether time is displayed with a 12-hour or 24-hour clock format.
Automatic(12-hour form
2 Local Volume Determines whether or not to display the following volume levels: handset receiver volume, speaker volume, ringer tone volume and LCD contrast.
Automatic (Enable)
3 Screen Saver Sets Screen Saver related data. -
5
t)
tgz
tgz
e
232
1 Screen Saver Mode
Enable/Disable Screen Saver.Disable
2 Wait Time Set the Wait Time to launch Screen Saver 120min
4 Back Light Enable/disable the backlights of LCD and digit keys. Automatic (Enable)
5 Font Size Change the displayed character size on the LCD. Standard(16do
6 Language Select a language to be displayed on LCD. Automatic
4 Change Password Change the password to lock/unlock the telephone. 0000
5 Security Not used. -
6 Peripherals Not used -
0 Setting Reset Reset the telephone settings. -
2 Download Set the data required for the file downloading. -
1 Download Files Download the files for Music on Hold, ringer tone and -
1 Hold Music Download a file for Music on Hold. MOH.wav
2 Ring Tone Download files for ringer tones -
1. Download 1 Download files for ringer tone (Download 1). Melody1.wav
2. Download 2 Download files for ringer tone (Download 2). Melody2.wav
3. Download 3 Download files for ringer tone (Download 3). Melody3.wav
3 Directory Download the directory files. Directory.csv
2 Download Address Enter an IP address of the FTP/TFTP server. 0.0.0.0
3 Protocol Select a protocol of the server (either FTP or TFTP). FTP
4 FTP Settings Set necessary data when using FTP service. -
1 User ID Enter a user ID for downloading via FTP server. -
2 Password Enter a password for downloading via FTP server. -
3 Folder Specify the directory where the download file is stored. -
3 Data Backup/Restore Set the data required for the file backup/restore. -
1 Data Backup Specify the file name to be backed up. PersonalData.
2 Data Restore Specify the file name to be restored. PersonalData.
Menu Item Description Default Valu
e
233
3 Server Address Enter an IP address of the FTP/TFTP server. 0.0.0.0
4 Protocol Select a protocol of the server (either FTP or TFTP). FTP
5 FTP Settings Set necessary data when using FTP service. -
1 User ID Enter a user ID for the data backup via FTP server. -
2 Password Enter a password for data backup via FTP server. -
3 Folder Specify the destination directory of FTP server. -
Menu Item Description Default Valu
ME
M
234
NU LIST FOR DT710 Series
enu List For Tool
Menu Item Description
Menu Press key while indicating the current time on LCD.
Tool Not used.
Setting To make the user setting of DT Series.
Config To make the configuration setting of DT Series. For details, please contact the system administrator.
Menu Item Description Default Value
1 Tool
1 ---------------------- Not used. -
Menu
1
2
0
1
M
e
)
-
235
enu List For Setting
Menu Item Description Default Valu2 Setting
1 User Setting Make the user setting of DT Series.
1 Incoming Call Settings for incoming call.
1 Offhook Ring Enable/Disable Off-hook ringing. Enable
2 Ring Tone Select a ringer tone for External Call and Internal Call.Automatic / Tone Type 1~14
Automatic(Tone Type1
3 Headset Ring Vol-ume
Not used. -
2 Talk Settings for telephone conversation.
1 RTP Alarm Enable/disable RTP alarm. Automatic
2 DTMF Tone Enable/disable DTMF tone. Automatic
3 Key Touch Tone Set key touch tone generated when the digit keys are pressed while the telephone is off-hook. Automatic
4 Hold Music Select a Music on Hold to be heard by DT Series user. Default
3 Display Settings for LCD display. -
1 Time Format Determines whether time is displayed with a 12-hour or 24-hour clock format.
Automatic (12hour format)
2 Local Volume Determines whether or not to display the following volume levels: handset receiver volume, speaker volume, ringer tone volume and LCD contrast.
Automatic (Enable)
3 Screen Saver Sets Screen Saver related data. -
1 Screen Saver Mode
Enable/Disable Screen Saver.Disable
2 Wait Time Set the Wait Time to launch Screen Saver 120min
4 Language Select a language to be displayed on LCD. Automatic
4 Change Password Change the password to lock/unlock the telephone. 0000
0 Setting Reset Reset the telephone settings. -
2 Download Set the data required for the file downloading. -
2
tgz
tgz
e
236
1 Download Files Download the files for Music on Hold, ringer tone and -
1 Hold Music Download a file for Music on Hold. MOH.wav
2 Download Address Enter an IP address of the FTP/TFTP server. 0.0.0.0
3 Protocol Select a protocol of the server (either FTP or TFTP). FTP
4 FTP Settings Set necessary data when using FTP service. -
1 User ID Enter a user ID for downloading via FTP server. -
2 Password Enter a password for downloading via FTP server. -
3 Folder Specify the directory where the download file is stored. -
3 Data Backup/Restore Set the data required for the file backup/restore. -
1 Data Backup Specify the file name to be backed up. PersonalData.
2 Data Restore Specify the file name to be restored. PersonalData.
3 Server Address Enter an IP address of the FTP/TFTP server. 0.0.0.0
4 Protocol Select a protocol of the server (either FTP or TFTP). FTP
5 FTP Settings Set necessary data when using FTP service. -
1 User ID Enter a user ID for the data backup via FTP server. -
2 Password Enter a password for data backup via FTP server. -
3 Folder Specify the destination directory of FTP server. -
Menu Item Description Default Valu
ME
M
237
NU LIST FOR DT330 Series
enu List For Call History
Menu Item Description
Menu Press key while indicating the current time on LCD.
Call History To view call history data.
Directory To access Phonebook feature. For details, see PHONEBOOK in chapter 5.
Settings To make the user setting of DT Series.
Menu Item Description Default Value
1 Call History
1 Incoming Displays the history of incoming calls. You can also make a call from this menu. -
3 Outgoing Displays the history of outgoing calls. You can also make a call from this menu. -
Menu
1
2
3
1
238
This page is for your notes.
1OUWeb rowser(Inte licationsoftw
N
N ng thee net-
N
239
0.WEB PROGRAMMING
TLINE Programming allows you to configure the terminal settings of DT Series from the PC. An Internet brnet Explorer, etc.) is used to access Web Programming. It is not necessary to install any special appare onto the PC.
PC Requirements For Web Programming
ote: This feature is only available for DT700 Series.
ote: DT700 Series and Web Programming PC needs to be connected to the same network. When downloadifiles for Music on Hold, Ringer Tone and Directory to the DT Series, FTP (TFTP server) is required on thwork. For details on the FTP service, contact the System Administrator.
ote: Terminal settings through the Web Programming is available while the DT700 Series logs into the system.
Items Operating Conditions
Operating System Microsoft Windows XP/VistaCPU Comply with conditions for use of Microsoft Windows or Micro-
soft Internet Explorer.Memory
Browser Microsoft Internet Explorer 6.0 or later
Monitor SVGA (minimum: 800 600 pixel, recommended: 1024 768 pixel,)
Others Mouse, LAN connection port (RJ-45)
TOFollo
STE
STE
STE ote 1),
N tting.
N
240
LOGINw the steps below to open the Web Programming.
P 1: Start up Internet browser on the PC.
P 2: Enter IP address of the target DT700 Series on the address toolbar and then press Enter key.
P 3: The Web Programming Login screen appears. Enter a user name (type “USER”) and a password (Nthen click .
ote: Enter the same password used when logging into the DT750. “0000” is used as password by the default se
ote: For IP address of DT Series, contact the System Administrator.
OK
STE
N oblem
241
P 4: The following Web Programming Home screen appears.
ote: When the login screen does not appear, check the LAN connection status and entered IP address. If the prpersists, please contact the system administrator.
TOFollo
STE
STE
STE
242
LOGOUTw the steps below to exit the Web Programming.
P 1: Click at the lower left of the screen.
P 2: The confirmation message appears. Click to log out of Web Programming.
P 3: The display changes as follows. Click .
Logout
OK
Back
STE
Not
Not
243
P 4: After the Web Programming Login screen is displayed, close the Internet browser.
e: Make sure to perform the logout operation after the data setting of the telephone.
e: When 15 minutes have passed leaving the PC without operation after log in to Web Programming, youare forcibly logged out from the Web Programming.
HO
As a tone forexter al. Fordeta
STE
STE
STE
STE
244
W TO OPERATE
n example of setting method on the Web Programming, the following explains how to change the ringer nal call. Web Programming includes the same menu configuration as "Setting" of DT700 Series termin
ils on each menu item, see SETUP WITH MENU KEY FOR DT700 SERIES in 3.TERMINAL SETUP.
P 1: From the Home screen, click User Setting Incoming Call Ring Tone External Call.P 2: Select a desired tone type by clicking the corresponding radio button.
P 3: Click to save the change to the database.
P 4: A confirmation dialog appears. Click on the dialog.
OK
STEP 1: Click items to navigate through the menu.
STEP 3: Click OK button
STEP 2: Click the radio button to select a parameter.
Click Logout button to exitfrom the Web Programming. to accept the selection.
OK
Printed in Japan1008-040