DSI installation quick manual Memory Display - · PDF fileDSI installation quick manual ......
1
Driver Safety and Information Computer Installation quick manual version ENG1.6 Copyright 2009 Stinger Stinger www.stinger.com DSI installation quick manual For optimal performance of the DSI Computer it is important to read this installation quick manual carefully. For questions please call Stinger technical support at +31 (0) 252 - 418095. Please first confer with the customer to determine the desired position for the Memory Display in the car . We advise to place the Display Holder in such a way, that the Memory Display will be in the line of sight so that all information is clearly vissible and the Memory Display can safely be operated during driving. In the cockpit In or behind the bumper / grill Laser Analyzer Box Extension Box Computer Center 5 2 1 Display Holder Memory Display Audio Speaker 8 9 6 Power Plug I/O Plug 11 10 Under the bonnet Under the dashboard GPS Antenna 7 Car specific Module locations Schematic view Step by step instructions 8 9 7 1 10 11 6 3 4 2 5 Extension Box Place the Extension Box horizontally (as depicted) under the bonnet, in a reasonably humidity-free location. • Connect the module to the FRONT port of the Computer Center. Do not yet close the lid of the Extension Box. Memory Display + Display Holder Place the Display Holder at a convenient location for the driver. When using the screw attachment, place an extra 1mm washer ring on the back side of the Display Holder. Do not place the ring if the Display Holder is placed on a carkit mount. • Connect the module to the DISPLAY port of the Computer Center. • Place the Display on the Display Holder. Closing the Extension Box and Laser Analyzer Box After all the cables have been connected, it is important to close the boxes (see picture 2 and 5) in a water resistant manner. Place the cables in the holes of the oppositely facing ‘rubber seals’ (see example). This prevents moisture from getting into the box.. Next, place the rubber seals with the now inserted cables into the slot, as depicted in the example on the left. Make sure the rubbers are pushed down all the way using silicone spray to facilitate this. Put the lid back on so that it is tight and secure. Computer Center The DSI’s central computer must be placed in the dashboard in a humidity-free location. • Mount the CC with tie-wraps or screws. Bl 8-pole I/O plug Connect the orange wire to the ignition-actuated 13.8V battery power. • If so desired, attach the green Mute-cable to the Mute-wire of the radio. • The black wire is for future use Bl Red 2-pole power plug Connect the red wire to the 13.8 V battery power. • Connect the black wire to a ‘clean’ metal ground-point of the car chassis. Spectrum Analyzer Place the Spectrum Analyzer at the front of the car behind the bumber, spoiler or grill. Preferably place it behind flat en smooth plastic, and certainly not behind metal. • The large, smooth side that has no imprints, must face straight forward in the driving direction, with the cable coming out on the left or right side, as depicted. • Connect it to any port of the Extension Box. Rubber seals Rubber seals Cut outs Cable 1 Laser Analyzer Box Place the Laser Analyzer Box under the bonnet. • Connect the Laser Analyzer Box to the Extension Box with the plug in the left “CC port” and connect the other end to any of the ports on the Extension Box. Do not yet close the lid. Port for the Extension Box 5 GPS Antenna Place the antenna on the dashboard. If the car has a heat-repelling windshield, it is better to place the antenna outside the car. In that case, the antenna may be placed in the box at the top end of the bonnet. • Connect the cable of the antenna to the GPS port of the Computer Center. 7 9 10 11 12 8 2 3 Front Laser (Round) Drill a 21 mm opening in the bumper or spoiler. Using the angled rings, place the Laser facing as straight forward as possible. Fasten the Laser with the provided spring and ring. Front Laser (Square) Place the Laser, as straight as possible, in the grill, making sure the arrow is pointing up. Connect the Lasers in port 1, 2, 3 or 4 in the Laser Analyzer Box which you must install next. Lasers The Lasers must have an unobstructed ‘view’ and should point as straight as possible in the driving direction. Consult the Stinger Laser Analyzer installation manual for more information. 4 FACING FORWARD Square Laser Round Spectrum Analyzer 4 3 Speaker Place the speaker under the dashboard. • Connect the module to the port of the Computer Center. 6 Bl Bl Red
Transcript of DSI installation quick manual Memory Display - · PDF fileDSI installation quick manual ......
Driver Safety and Information ComputerInstallation quick manual version ENG1.6Copyright 2009 Stinger
Stingerwww.stinger.com
DSI installation quick manual
For optimal performance of the DSI Computer it is important to read this installation quick manual carefully. For questions please call Stinger technical support at +31 (0) 252 - 418095.
Please first confer with the customer to determine the desired position for the Memory Display in the car. We advise to place the Display Holder in such a way, that the Memory Display will be in the line of sight so that all information is clearly vissible and the Memory Display can safely be operated during driving.
In the cockpit
In or behind the bumper / grill
LaserAnalyzer Box
ExtensionBox
ComputerCenter
52
1
DisplayHolder
MemoryDisplay
AudioSpeaker
8
9
6
PowerPlug
I/OPlug
11
10
Under the bonnet
Under the dashboard
GPSAntenna
7
Car specific
Module locations
Schematic view Step by step instructions
897
1 10 11
6
3
4
25
Extension BoxPlace the Extension Box horizontally (as depicted) under the bonnet, in a reasonably humidity-free location. • Connect the module to the FRONT port of the Computer Center. Do not yet close the lid of the Extension Box.
Memory Display + Display Holder Place the Display Holder at a convenient location for the driver. When using the screw attachment, place an extra 1mm washer ring on the back side of the Display Holder. Do not place the ring if the Display Holder is placed on a carkit mount.• Connect the module to the DISPLAY port of the Computer Center.• Place the Display on the Display Holder.
Closing the Extension Box and Laser Analyzer BoxAfter all the cables have been connected, it is important to close the boxes (see picture 2 and 5) in a water resistant manner. Place the cables in the holes of the oppositely facing ‘rubber seals’ (see example). This prevents moisture from getting into the box..Next, place the rubber seals with the now inserted cables into the slot, as depicted in the example on the left. Make sure the rubbers are pushed down all the way using silicone spray to facilitate this. Put the lid back on so that it is tight and secure.
Computer CenterThe DSI’s central computer must be placed in the dashboard in a humidity-free location.• Mount the CC with tie-wraps or screws.
Bl
8-pole I/O plugConnect the orange wire to the ignition-actuated 13.8V battery power.• If so desired, attach the green Mute-cable to the Mute-wire of the radio.• The black wire is for future use
Bl
Red
2-pole power plugConnect the red wire to the 13.8 V battery power.• Connect the black wire to a ‘clean’ metal ground-point of the car chassis.
Spectrum AnalyzerPlace the Spectrum Analyzer at the front of the car behind the bumber, spoiler or grill. Preferably place it behind flat en smooth plastic, and certainly not behind metal.• The large, smooth side that has no imprints,
must face straight forward in the driving direction, with the cable coming out on the left or right side, as depicted.
• Connect it to any port of the Extension Box.
Rubberseals
Rubberseals
Cut outs
Cable
1
Laser Analyzer BoxPlace the Laser Analyzer Box under the bonnet.• Connect the Laser Analyzer Box to the Extension Box with the plug in the left “CC port” and connect the other end to any of the ports on the Extension Box. Do not yet close the lid.
Port for theExtension Box
5
GPS AntennaPlace the antenna on the dashboard. If the car has a heat-repelling windshield, it is better to place the antenna outside the car. In that case, the antenna may be placed in the box at the top end of the bonnet.• Connect the cable of the antenna to the GPS port of the Computer Center.
7
9
10
11
12
8
2
3
Front Laser (Round)Drill a 21 mm opening in the bumper or spoiler. Using the angled rings, place the Laser facing as straight forward as possible. Fasten the Laser with the provided spring and ring.
Front Laser (Square)Place the Laser, as straight as possible, in the grill, making sure the arrow is pointing up.
Connect the Lasers in port 1, 2, 3 or 4 in the Laser Analyzer Box which you must install next.
LasersThe Lasers must have an unobstructed ‘view’ and should point as straight as possible in the driving direction. Consult the Stinger Laser Analyzer installation manual for more information.
4
FACING FORWARD
SquareLaser RoundSpectrumAnalyzer
43
SpeakerPlace the speaker under the dashboard.• Connect the module to the port of the Computer Center.
6
Bl
Bl
Red
