D&S HUMIDITY SOLUTIONS INC.en.dshumidity.com/images/ds_brochure.pdf · ·Permanent easily...
Transcript of D&S HUMIDITY SOLUTIONS INC.en.dshumidity.com/images/ds_brochure.pdf · ·Permanent easily...
Distributor:
D&S HUMIDITY SOLUTIONS INC.
......highquality and service
D&S HUMIDITY SOLUTIONS INC.
......highquality and service
......highquality and serviceD&S HUMIDITY SOLUTIONS INC.
......highquality and serviceD&S HUMIDITY SOLUTIONS INC.
......highquality and serviceD&S HUMIDITY SOLUTIONS INC.
Applications
Why D&S Humidity?
•D&S offers humidity solutions with leading-edge
technology and quality services.
•D&S innovative products make contributions towards saving energy and reducing CO2emissions.
•D&S focus on customer-driven applications and provides advanced, energy-efficient and high-qualityproduction solutions and services.
•D&S have: Resistance steam humidifier, Jet steam humidifier, Evaporative humidifier, and Mist humidifier.
•Our customer’s value: Supply top quality products and services.
......highquality and serviceD&S HUMIDITY SOLUTIONS INC.
DSW Evaporative Humidifer/Cooling
The DSW evaporative humidifier series is
usually incorporated into an A.H.U after
the pre‐heating coil and before the
cooling coil.
The DSW humidifiers can be easily
integrated into an air duct system. Usually
the designer must provide a duct section
enlargement to ensure the correct air
velocity but retrofit is common and easy
to incorporate.
The DSW humidifiers can be delivered
in modules to build any size of
“humidification bank” into a large A.H.U
for large airflows down to pre assembled
smaller units which make installation
straight forward.
Technical specifications
Depending On Unit Size
Output (kg/h) ‐‐‐‐‐‐‐‐‐‐‐10 ~ 1000
Power supply (V)‐‐‐‐‐‐‐‐‐‐220V Single Phase
Power consumption (kW)‐‐‐‐‐‐ 0.5 ~ 1.0
Output modulation‐‐‐‐‐‐‐‐‐On/Off or Proportional
Supply water‐‐‐‐‐‐‐‐‐‐‐‐Mains or De‐mineralised Water
Type of control‐‐‐‐‐‐‐‐‐‐‐On/Off or 0 ~ 10V / 4 ~ 20mA
DSW Evaporstive humididier
Using a corrugated and cross channel configuration ,
the media has a compact structure maintaining
optimum performance at low pressure drop. As they
are inorganic, they are incombustible , certified as fire
proof. It’s inorganic compound makes it odourless. The
media contains a small amount of silver ion which acts
as a biocide to prevent fungus and also helps any water
deposits to release from the media allowing it to stay
cleaner.
Advantages
·Low energy
·Any water quality
·Very close control ±3% ~±5% RH
·Fire retardant matrix
·Single phase
·High humidity duties
·Advantageous cooling up to 13℃
......highquality and serviceD&S HUMIDITY SOLUTIONS INC.
DSE Resistance Steam Humidify
The main features of the DSE are:
·Permanent easily serviceable stainless steel evaporation chamber
·On/Off or Modulating control functions
·Interactive LCD display and microprocessor controlled self diagnostics
·AFEC. technology insures safe and efficient operation
·Functions exceptionally well in severe, normal or DI/RO water conditions
·Equipped with revolutionary drain pump and waste water cooling device
·Available with "BACnet" communication interface
Output and Power Consumption
Note:Designate the letter M for modulating units.(ie:DSE20M) Designate the letter D for units operating with deionized water.
Technical specifications
Depending On Unit Size
Output (kg/h).............4 ~ 120
Power supply (V)..........220V Single Phase or
380V Three Phase
Power consumption (kW)...3.7 ~ 90
Output modulation.........On/Off or Proportional
Supply water..............Mains or
De‐mineralised Water
Type of control.............On/Off or
0 ~ 10V / 4 ~ 20mA
Dimensions
W
D
H
modle power Kw capacity Kg/hr amperage A #of outlets dia.of outlets dia.of mainfold
DSE10 7.5 10 11.4 1 Ø30 Ø30
DSE20 15 20 22.8 1 Ø30 Ø30
DSE30 22.5 30 34.2 2 Ø30 Ø38.5
DSE-40 30 40 45.6 2 Ø30 Ø38.5
DSE-60 45 60 68.4 3 Ø30 Ø63.5
DSE-80 60 80 91.2 4 Ø30 Ø63.5
DSE-100 75 100 114.0 5 Ø30 Ø76
DSE-120 90 120 136.7 4 Ø40 Ø76
Output and Power Consumption
model W D H dia.of inlet dia.of drain
DSE10 450 430 887 G 1/2" G1"
DSE20 690 430 887 G 1/2" G1"
DSE30 690 430 887 G 1/2" G5/4"
DSE-40 690 430 887 G 1/2" G5/4"
DSE-60 690 430 887 G 1/2" G5/4"
DSE-80 890 500 995 G 1/2" G5/4"
DSE-100 890 500 995 G 1/2" G5/4"
DSE-120 890 500 995 G 1/2" G5/4"
Dimensions
......highquality and serviceD&S HUMIDITY SOLUTIONS INC.
Single Tube
·Low capacities
·High absorption distance (must not be critical)
·Low cost
Multi Rack
·Medium to high capacities
·Medium to low absorpotion distance
·Shipped lose and comes with the header
·Could ship fully assembl
DSJ Jet Steam Humidify
The DSJ Advantags
The DSJ are uniquely designed to provide you with an eco‐energy program. The DSJ multiple
configurations combined with our unique electronic steam controller (ESO) provide virtually no
spitting on cold start‐ups. Additionally, contrary to the competition where the steam manifold is
constantly heated thus creating hot air and energy loss, the DSJ comes with a jacketed valve to
control the heating of the jactet.
Typical Applications
The DSJ can providesteam from a facility steam boiler for different environments such as:
Principle of Operations
2.9 PSI 14.5 PSI 29 PSI 43.5 PSI 58 PSI
0.3 3.3 5.1 7.9 9.9 13.5
1.0 8.8 20.7 30.9 40.4 54.1
2.5 19.9 47.0 77.2 88.3 129.1
4.9 49.6 109.2 151.1 215.1 273.6
7.6 59.6 136.8 233.9 335.4 432.53/4"
1/2"
Single TubeCapacity (lbs/hr)
Distributor Size Cv
9.4 75.0 166.6 289.1 412.6 500.9
10.2 88.3 172.1 313.3 452.3 551.6
11.4 121.4 225.1 353.0 478.8 606.8
15.5 165.5 311.1 476.6 653.1 827.4
22.2 319.9 428.1 686.2 988.5 1301.9
28.4 412.6 542.8 876.0 1255.5 1677.0
1 1/4"
1 1/2"
2.9 PSI 14.5 PSI 29 PSI 43.5 PSI 58 PSI
0.3 4.0 6.1 9.5 11.9 16.2
1.0 10.6 24.9 37.1 48.5 64.9
2.5 23.8 56.4 92.7 105.9 154.9
4.9 59.6 131.1 181.4 258.2 328.3
7.6 71.5 164.2 280.7 402.5 519.0
1/2"
3/4"
Multi Rack
Separator Size CvCapacity (lbs/hr)
7.6 71.5 164.2 280.7 402.5 519.0
9.4 90.0 199.9 346.9 495.1 601.1
10.2 105.9 206.5 376.0 542.8 662.0
11.4 145.6 270.1 423.7 574.6 728.2
15.5 198.6 373.3 571.9 783.8 992.9
22.2 383.9 513.7 823.5 1186.2 1562.2
28.4 495.1 651.4 1051.2 1506.6 2012.4
3/4"
1 1/4"
1 1/2"
Technical specifications
Depending On Unit Size
Output (kg/h)..........3~800
Power supply (V).......220V Single Phase
Output modulation......On/Off or
Proportional
Supply water...........Steam
Type of control.........On/Off or
0 ~ 10V / 4 ~ 20mA
......highquality and serviceD&S HUMIDITY SOLUTIONS INC.
DSAW Air water mixed humidily
2. The Principle of Mixed Gas Water Sprayer
1) Principle of Sprayer
Wet spray system adopts the principle of vacuum siphon for operation, generating superfine
mist of two-stage atomizing system.In the two-stage atomization system, air water mixture
sprays out from the center hole, therefore realizing the first atomization; when fully mixed
with the gas sprayed out from the side hole, it achieves the second atomization. Adjust the
compression ratio of gas and water according to requirements to obtain the best spray effect;
the spray particle size is between: 5μm ~10μm.
2) Spray System Characteristics
The spray system is compact, but has better humidification performance, and compared
with similar products, it has lighter weight, shorter total length shorter and more excellent
performance. With its soft visual appearance, delicate and circular design, the spray system can
avoid destroying the indoor harmony.
3) Energy-Saving and Maintenance Free
The compressed air consumption is equivalent to 60% of the same kind of nozzle, making it
more energy saving and environmental protective, maintenance free, and of long service life.
4) System Characteristics
With good atomization effect, special vacuum valve design, and compressed air negative
pressure induced humidification.
Its automatic control system can better display the humidity of the humidifying area.
Its multiple safety protection devices ensure that there will be no dripping of water or water
spray from the nozzle.
Fast and convenient to install, its spraying direction can be adjusted at any angle, with good
performance and long service life.
Gas and water mixed design helps solve the problem of easy nozzle blockage.
Its two-stage atomization system ensures extreme uniformity of spray particles, and extremely
fine water mist can evaporate quickly, thereby avoiding the wetland phenomenon.
Humidification applicable to large space with already existing compressed air equipment
is currently one of the most energy efficient humidification. Both of its initial investment
cost and installation cost are far lower than your budget, with therefore good effect, less
investment, quick results, and low energy consumption
1) Efficient spray, humidification, spray system adopt two-fluid soda hybrid technology,
its droplet particles are controlled at 5~10μm, uniformed, without leakage or dripping,
its atomization efficiency is more than 99%, though the equipment is small, its volume of
spray is large: 11kg/h
2) High Efficiency Dedusting
In the atomization process, water molecules collide with each other with high-speedand
therefore produce a large number of oxygen ions containing negative charges, by applying
the principle of positive and negative attraction, they can adsorb and assembly a large
number of dust particles in the air, which, after accumulation, become dustfall.
3) Destaticization
The spray process can producea large number of negative oxygen ions, which neutralize
positive charges, and eliminate static electricity; after humidity increases, it can reduce the
generation of static electricity
Technical specificationsParameters of different spray nozzles under 3bar atmospheric pressure
conditions:
Number of spray nozzle (piece) …………………………………………1
Volume of spray (L/h)………………………………………………………11
Air consumption (m3/min)……………………………………………..0.25
Spray distance (m) ……………………………………………………10-15
Spray particle (μm) ……………………………………………………..5-10
Droplets reached area (m2) …………………………………….150-200
......highquality and serviceD&S HUMIDITY SOLUTIONS INC.
DSM Mist Humidify
High precision control at ±3% RH over a range of capicities from 100~2000kg/h with Certified
Hygiene for use in air conditioning and hospital applications makes this system a perfect solution
to solve many cooling or humidity problems.
The atomizing racks are straight forward to install and allow the lines to be drained and
automatic flushing to ensure hygine standards are continuously met. The systems then
distributes the demineralized water ,to prevent dusting and reducing maintenance ,at a pressure
of 70 bar to the nozzles.
Service & Maintenance
Delivery Address:11980 Hammersmith Way,Richmond BC Canada V7A0A4Tel: +1-778-829-0586Fax: +1-604-248-6475www.dshumidity.comE‐mail: [email protected]
Technical specifications
Depending On Unit Size
Output (kg/h)............60~2000
Power supply (V).........220V Single Phase or
380V Three Phase
Power consumption (kW)..2~4.5
Output modulation....... On/Off or Proportional
Type of control...........On/Off or
0 ~ 10V/ 4 ~ 20mA
For more information, please contact:
Care for your Humidifier
HumiServ, our humidifier service and installation division excels in the delivery,
installationand maintenance of all types of humidifier. We serve throughout Canada and
workon any piece of humidification equipment requiring specialist knowledge. From
printing andtextiles industries, to pharmaceutical, medical devices and offshore applications
our engineers willhelp you save cost and free up your own personnel to attend to more
demanding calls.
Planned Maintenance
At the centre of our operations is the delivery of our humidifier Planned Maintenance
Agreements. These agreements provide a complete humidifier care package designed
tomeet your specific requirements and give you peak performance, extended equipment
life,predictable costs and peace of mind.
Installation and Commissioning
From turnkey projects to the installation of a single unit we can help. Making sure your
humidifiers are installed and set up correctly will give you reliable operation and
eliminatethe problems resulting from poor initial installation and commissioning.