DRISEAM REINFORCEMENT TAPE - · PDF fileKNIT SEAM REINFORCEMENT TAPE SRT4000 ... NOZZLE...
Transcript of DRISEAM REINFORCEMENT TAPE - · PDF fileKNIT SEAM REINFORCEMENT TAPE SRT4000 ... NOZZLE...
DRISEAM REINFORCEMENT TAPE
• Ultimate breathability
• Integrated moisture transport system using Bemis FlowfreeTM in partnership with drirelease fabrics
• Use for construction or aesthetic
• Reduces seam weight
• Strengthens seams
• Soft hand feel
• Withstands high heat wash
Why It’s Worth a Look
Engineered with
DRISEAM REINFORCEMENT TAPE
/ CORE COLORS
Snow
Pantone 11-0601 TPX
Navy
Pantone 19-4024 TPX
Black
Pantone 19-4006 TPX
Red
Pantone 18-1763 TPX
Radiation
Pantone 388C
DSRT / 1
DRISEAM REINFORCEMENT TAPE
/ CORE COLORS
Heather Cool Grey
Heather Black
Heather Gold
Heather Red
Heather Purple
DSRT / 2
TECHNICAL INFORMATION
DRISEAM REINFORCEMENT TAPE DSRT1000
MATERIALS Polyester/Cotton/Spandex Knit Lightweight Fabric/Polyurethane Adhesive
STOCKED WIDTH 1372 mm
ADHESIVE SOFTENING POINT 83°C (181°F)
TOTAL THICKNESS 0.014” (0.36 mm)
ADHESIVE THICKNESS 0.004” (0.10 mm)
MATERIAL WEIGHT 2.15 g/m at 10 mm
MODULUS @ 50% ELONGATION1 10 mm
SERVICE TEMPERATURE −30°C to 60°C (−22°F to 140°F)
WASH Excellent up to 60°C water temperature
INITIAL BONDING CONDITIONS2
FLAT PRESS
TEMPERATURE 110°C to 150°C
TIME 15 to 25 seconds
PRESSURE 2.8 to 4.2 bar (40 to 60 psi)
1Modulus: The force required to pull a 12 mm (0.47”) wide sample by specified gauge to 50% elongation at 508 mm (20”) per minute after 3 cycles.2Recommended bonding conditions will vary between different machinery and fabrics. The recommended conditions stated are a starting point only. Optimal bonding conditions should be established by the factory of the specific application.
NOTE: Seller hereby excludes any express warranties and the implied warranties of merchantability and fitness for a particular purpose. The following is made in lieu of any such “warranties.” Bemis Associates, Inc. believes the information and specification supplied are reliable, but does not guarantee that any results shown or claimed will be obtained. Before using, the user shall determine the suitability and fitness of the product for its intended use. The user assumes all risks and liability whatever in connection with its own tests and use. Neither seller nor manufacturer shall be liable for any injury, loss or damage, direct or consequential, arising out of the use, or misuse or inability to use this product.
KNITSEAM REINFORCEMENT TAPE
• Incorporates knit fabric for differentiated look and hand feel
• High stretch
• Use for construction or aesthetic
• Reduces seam weight
• Strengthens seams
• Withstands high heat wash
Why It’s Worth a Look
KNIT SEAM REINFORCEMENT TAPE
/ CORE COLORS
Snow
Pantone 11-0601 TPX
Cool Grey
Pantone 428C
Ash
Pantone 19-4104 TPX
Navy
Pantone 19-4024 TPX
Black
Pantone 19-4006 TPX
KSRT / 1
KNIT SEAM REINFORCEMENT TAPE
/ CORE COLORS
Red
Pantone 18-1763 TPX
Radiation
Pantone 388C
KSRT / 2
TECHNICAL INFORMATION
KNIT SEAM REINFORCEMENT TAPE SRT4000
MATERIAL Nylon/Spandex Knit Fabric/Polyurethane Adhesive
STOCKED WIDTH 10 mm, 1372 mm
WEIGHT 3.23 g/m at 10 mm
HAND Soft
WASH Excellent up to 60°C
MODULUS1 1.3 lbf (0.6 kgf)
SOFTENING POINT 95°C (203°F)
TOTAL THICKNESS 0.020” (0.51 mm)
ADHESIVE THICKNESS 0.004” (0.10 mm)
SERVICE TEMPERATURE −30°C to 60°C (−22°F to 140°F)
INITIAL BONDING CONDITIONS2
HOT AIR
NOZZLE POSITION Same as a standard 2-layer seam tape
NOZZLE AIR TEMPERATURE 550°C to 650°C
NOZZLE PRESSURE 0.09 mpa
ROLLER PRESSURE 0.4 mpa
LINE SPEED 4 m/min
FLAT PRESS
TEMPERATURE 115°C to 170°C
TIME 15 to 25 seconds
PRESSURE 2.8 to 4.2 bar (40 to 60 psi)
Self fabric lamination is available. Contact Bemis for details.
1Modulus: The force required to pull a 12 mm (0.47”) wide sample by specified gauge to 50% elongation at 508 mm (20”) per minute after 3 cycles.2Recommended bonding conditions will vary between different machinery and fabrics. The recommended conditions stated are a starting point only. Optimal bonding conditions should be established by the factory of the specific application.
NOTE: Seller hereby excludes any express warranties and the implied warranties of merchantability and fitness for a particular purpose. The following is made in lieu of any such “warranties.” Bemis Associates, Inc. believes the information and specification supplied are reliable, but does not guarantee that any results shown or claimed will be obtained. Before using, the user shall determine the suitability and fitness of the product for its intended use. The user assumes all risks and liability whatever in connection with its own tests and use. Neither seller nor manufacturer shall be liable for any injury, loss or damage, direct or consequential, arising out of the use, or misuse or inability to use this product.
CertificationOeko Tek, Standard 100 Class 1 (Test No. 6187)REACH compliant, European Union (EU) legislation concerning the Registration, Evaluation, Authorization and Restriction of Chemicals (REACH)
WOVENSEAM REINFORCEMENT TAPE
• Incorporates woven fabric for differentiated look and hand feel
• High stretch
• Use for construction or aesthetic
• Reduces seam weight
• Strengthens seams
• Withstands high heat wash
Why It’s Worth a Look
WOVEN SEAM REINFORCEMENT TAPE
/ CORE COLORS
Cool Grey
Pantone 428C
Ash
Pantone 19-4104 TPX
Navy
Pantone 19-4024 TPX
Snow
Pantone 11-0601 TPX
Black
Pantone 19-4006 TPX
WSRT / 1
WOVEN SEAM REINFORCEMENT TAPE
/ CORE COLORS
Red
Pantone 18-1763 TPX
Radiation
Pantone 388C
WSRT / 2
TECHNICAL INFORMATION
WOVEN SEAM REINFORCEMENT TAPE SRT5000
MATERIAL Polyester/Spandex Woven Fabric/Polyurethane Adhesive
STOCKED WIDTH 10 mm, 1372 mm
WEIGHT 2.88 g/m at 10 mm
HAND Soft
WASH Excellent up to 60°C
MODULUS1 4.5 lbf (2.0 kgf)
SOFTENING POINT 95°C (203°F)
TOTAL THICKNESS 0.012” (0.31 mm)
ADHESIVE THICKNESS 0.004” (0.10 mm)
SERVICE TEMPERATURE −30°C to 60°C (−22°F to 140°F)
INITIAL BONDING CONDITIONS2
HOT AIR
NOZZLE POSITION Same as a standard 2-layer seam tape
NOZZLE AIR TEMPERATURE 550°C to 650°C
NOZZLE PRESSURE 0.09 mpa
ROLLER PRESSURE 0.4 mpa
LINE SPEED 4 m/min
FLAT PRESS
TEMPERATURE 115°C to 170°C
TIME 15 to 25 seconds
PRESSURE 2.8 to 4.2 bar (40 to 60 psi)
Self fabric lamination is available. Contact Bemis for details.
1Modulus: The force required to pull a 12 mm (0.47”) wide sample by specified gauge to 50% elongation at 508 mm (20”) per minute after 3 cycles.2Recommended bonding conditions will vary between different machinery and fabrics. The recommended conditions stated are a starting point only. Optimal bonding conditions should be established by the factory of the specific application.
NOTE: Seller hereby excludes any express warranties and the implied warranties of merchantability and fitness for a particular purpose. The following is made in lieu of any such “warranties.” Bemis Associates, Inc. believes the information and specification supplied are reliable, but does not guarantee that any results shown or claimed will be obtained. Before using, the user shall determine the suitability and fitness of the product for its intended use. The user assumes all risks and liability whatever in connection with its own tests and use. Neither seller nor manufacturer shall be liable for any injury, loss or damage, direct or consequential, arising out of the use, or misuse or inability to use this product.
CertificationOeko Tek, Standard 100 Class 1 (Test No. 6187)REACH compliant, European Union (EU) legislation concerning the Registration, Evaluation, Authorization and Restriction of Chemicals (REACH)
HEATHERSEAM REINFORCEMENT TAPE
• Incorporates a heather look for a classic sportswear feel
• High stretch
• Use for construction or aesthetic
• Reduces seam weight
• Strengthens seams
• Soft hand feel
• Withstands high heat wash
Why It’s Worth a Look
WHY IT’S WORTH A LOOK
HEATHER SEAM REINFORCEMENT TAPE
Grey
*Stocked in slit width of 10 mm
Navy
Black
Gold
Red
/ CORE COLORS
HSRT / 1
TECHNICAL INFORMATION
HEATHER SEAM REINFORCEMENT TAPE HSRT4000
MATERIAL Polyester/Spandex Knit Heather Fabric/Polyurethane Adhesive
STOCKED WIDTH 1372 mm
WEIGHT 3.75 g/m
HAND Soft
WASH Excellent at 60°C
MODULUS @ 50% ELONGATION1 2.0 lbf (0.9 kgf)
ADHESIVE SOFTENING POINT 95°C (203°F)
TOTAL THICKNESS 0.024” (0.61 mm)
ADHESIVE THICKNESS 0.004” (0.10 mm)
SERVICE TEMPERATURE −30°C to 60°C (−22°F to 140°F)
INITIAL BONDING CONDITIONS2
FLAT PRESS
TEMPERATURE 115°C to 170°C
TIME 15 to 25 seconds
PRESSURE 2.8 to 4.2 bar (40 to 60 psi)
1Modulus: The force required to pull a 12 mm (0.47”) wide sample by specified gauge to 50% elongation at 508 mm (20”) per minute after 3 cycles.2Recommended bonding conditions will vary between different machinery and fabrics. The recommended conditions stated are a starting point only. Optimal bonding conditions should be established by the factory of the specific application.
NOTE: Seller hereby excludes any express warranties and the implied warranties of merchantability and fitness for a particular purpose. The following is made in lieu of any such “warranties.” Bemis Associates, Inc. believes the information and specification supplied are reliable, but does not guarantee that any results shown or claimed will be obtained. Before using, the user shall determine the suitability and fitness of the product for its intended use. The user assumes all risks and liability whatever in connection with its own tests and use. Neither seller nor manufacturer shall be liable for any injury, loss or damage, direct or consequential, arising out of the use, or misuse or inability to use this product.
REFLECTIVESEAM REINFORCEMENT TAPE
• Reflective properties
• High stretch
• Use for construction or aesthetic
• Reduces seam weight
• Strengthens seams
• Withstands high heat wash
Why It’s Worth a Look
REFLECTIVE SEAM REINFORCEMENT TAPE
/ CORE COLORS
Snow
Pantone 11-0601 TPX
Silver
~400 Cd/Lux
Gold
Pantone 871C
Navy
Pantone 19-4024 TPX
Black
Pantone 19-4006 TPX
RSRT / 1
REFLECTIVE SEAM REINFORCEMENT TAPE
/ CORE COLORS
Red
Pantone 18-1763 TPX
Radiation
Pantone 388C
Spray Tan
Pantone 1505C
RSRT / 2
TECHNICAL INFORMATION
REFLECTIVE SEAM REINFORCEMENT TAPE RSRT3000
MATERIAL Reflective Film/Polyester Spandex Knit Fabric/Polyurethane Adhesive
STOCKED WIDTH 10 mm, 1250 mm
WEIGHT 4.7 g/m
HAND Medium
WASH Excellent at 60°C
MODULUS @ 50% ELONGATION1 3.3 lbf (1.5 kgf)
CANDLEPOWER2 ~20 Cd/Lux (varies by color)
ADHESIVE SOFTENING POINT 95°C (203°F)
TOTAL THICKNESS 0.017” (0.43 mm)
ADHESIVE THICKNESS 0.004” (0.10 mm)
SERVICE TEMPERATURE −30°C to 60°C (−22°F to 140°F)
INITIAL BONDING CONDITIONS3
FLAT PRESS
TEMPERATURE 115°C to 170°C
TIME 15 to 25 seconds
PRESSURE 2.8 to 4.2 bar (40 to 60 psi)
1Modulus: The force required to pull a 12 mm (0.47”) wide sample by specified gauge to 50% elongation at 508 mm (20”) per minute after 3 cycles.2Candlepower: Varies by color and/or graphic. Contact Bemis for exact specifications.3Recommended bonding conditions will vary between different machinery and fabrics. The recommended conditions stated are a starting point only. Optimal bonding conditions should be established by the factory of the specific application.
NOTE: Seller hereby excludes any express warranties and the implied warranties of merchantability and fitness for a particular purpose. The following is made in lieu of any such “warranties.” Bemis Associates, Inc. believes the information and specification supplied are reliable, but does not guarantee that any results shown or claimed will be obtained. Before using, the user shall determine the suitability and fitness of the product for its intended use. The user assumes all risks and liability whatever in connection with its own tests and use. Neither seller nor manufacturer shall be liable for any injury, loss or damage, direct or consequential, arising out of the use, or misuse or inability to use this product.
NARROWSEAM REINFORCEMENT TAPE
• Ultimate stretch
• Reduces seam weight
• Use for construction or aesthetic
• Strengthens seams
• Soft hand feel
• Withstands high heat wash
Why It’s Worth a Look
NARROW SEAM REINFORCEMENT TAPE
/ CORE COLORS
Snow
Pantone 11-0601 TPX
*Stocked in slit width of 15 mm
Grey
Pantone 17-1501 TPX
*Stocked in slit width of 15 mm
Ash
Pantone 19-4104 TPX
Navy
Pantone 19-4024 TPX
Pitch
Pantone 19-4006 TPX
*Stocked in slit width of 15 mm
NSRT / 1
NARROW SEAM REINFORCEMENT TAPE
/ CORE COLORS
Red
Pantone 18-1763 TPX
Orange
Pantone 17-1464 TPX
Electric
Pantone 285C
Radiant
Pantone 803C
Luminous
Pantone 804C
NSRT / 2
NARROW SEAM REINFORCEMENT TAPE
/ CORE COLORS
Jolt
Pantone 802C
Blazing
Pantone 801C
Intense
Pantone 806C
Flashy
Pantone 807C
NSRT / 3
TECHNICAL INFORMATION
NARROW SEAM REINFORCEMENT TAPE NSRT3900
MATERIAL Nylon/Spandex Knit Narrow Width Ribbon/Polyurethane Adhesive
STOCKED WIDTH 10 mm
WEIGHT 3.15 g/m
HAND Medium
WASH Excellent at 60°C
MODULUS @ 50% ELONGATION1 1.3 lbf (0.6 kgf)
ADHESIVE SOFTENING POINT 95°C (203°F)
TOTAL THICKNESS 0.021” (0.53 mm)
ADHESIVE THICKNESS 0.004” (0.10 mm)
SERVICE TEMPERATURE −30°C to 60°C (−22°F to 140°F)
INITIAL BONDING CONDITIONS2
FLAT PRESS
TEMPERATURE 115°C to 170°C
TIME 15 to 25 seconds
PRESSURE 2.8 to 4.2 bar (40 to 60 psi)
1Modulus: The force required to pull a 12 mm (0.47”) wide sample by specified gauge to 50% elongation at 508 mm (20”) per minute after 3 cycles.2Recommended bonding conditions will vary between different machinery and fabrics. The recommended conditions stated are a starting point only. Optimal bonding conditions should be established by the factory of the specific application.
NOTE: Seller hereby excludes any express warranties and the implied warranties of merchantability and fitness for a particular purpose. The following is made in lieu of any such “warranties.” Bemis Associates, Inc. believes the information and specification supplied are reliable, but does not guarantee that any results shown or claimed will be obtained. Before using, the user shall determine the suitability and fitness of the product for its intended use. The user assumes all risks and liability whatever in connection with its own tests and use. Neither seller nor manufacturer shall be liable for any injury, loss or damage, direct or consequential, arising out of the use, or misuse or inability to use this product.
GRAPHICSEAM REINFORCEMENT TAPE
• Customizable in up to 8 colors using a proprietary digital print process
• High stretch
• Use for construction or aesthetic
• Reduces seam weight
• Strengthens seams
• Soft hand feel
• Withstands high heat wash
Why It’s Worth a Look
GRAPHIC SEAM REINFORCEMENT TAPE
/ CORE COLORS
Example A
Example B
Example C
GSRT / 1
TECHNICAL INFORMATION
GRAPHIC SEAM REINFORCEMENT TAPE GSRT1000
MATERIAL Digital Print Pigment: Nylon/Spandex Knit Narrow Width Ribbon/ Polyurethane Adhesive
STOCKED WIDTH 10 mm
WEIGHT 3.15 g/m
HAND Medium
WASH Excellent at 60°C
MODULUS @ 50% ELONGATION1 1.5 lbf (0.7 kgf)
ADHESIVE SOFTENING POINT 95°C (203°F)
TOTAL THICKNESS 0.020” (0.51 mm)
ADHESIVE THICKNESS 0.004” (0.10 mm)
SERVICE TEMPERATURE −30°C to 60°C (−22°F to 140°F)
INITIAL BONDING CONDITIONS2
FLAT PRESS
TEMPERATURE 115°C to 170°C
TIME 15 to 25 seconds
PRESSURE 2.8 to 4.2 bar (40 to 60 psi)
1Modulus: The force required to pull a 12 mm (0.47”) wide sample by specified gauge to 50% elongation at 508 mm (20”) per minute after 3 cycles.2Recommended bonding conditions will vary between different machinery and fabrics. The recommended conditions stated are a starting point only. Optimal bonding conditions should be established by the factory of the specific application.
NOTE: Seller hereby excludes any express warranties and the implied warranties of merchantability and fitness for a particular purpose. The following is made in lieu of any such “warranties.” Bemis Associates, Inc. believes the information and specification supplied are reliable, but does not guarantee that any results shown or claimed will be obtained. Before using, the user shall determine the suitability and fitness of the product for its intended use. The user assumes all risks and liability whatever in connection with its own tests and use. Neither seller nor manufacturer shall be liable for any injury, loss or damage, direct or consequential, arising out of the use, or misuse or inability to use this product.