Drill Press Safety PPT
-
Upload
jnordtvedt -
Category
Education
-
view
467 -
download
15
description
Transcript of Drill Press Safety PPT
![Page 1: Drill Press Safety PPT](https://reader034.fdocuments.us/reader034/viewer/2022052117/546776d4af79597c418b5d16/html5/thumbnails/1.jpg)
Drill PressDrill PressSafety Safety
InstructionsInstructions
![Page 2: Drill Press Safety PPT](https://reader034.fdocuments.us/reader034/viewer/2022052117/546776d4af79597c418b5d16/html5/thumbnails/2.jpg)
Obtain permission from your Obtain permission from your teacher before using the Drill teacher before using the Drill PressPress
During open lab you may use any machine that you have passed the safety test on and been through the demonstration.
![Page 3: Drill Press Safety PPT](https://reader034.fdocuments.us/reader034/viewer/2022052117/546776d4af79597c418b5d16/html5/thumbnails/3.jpg)
Wear face shield, safety glasses or Wear face shield, safety glasses or goggles at all times.goggles at all times.
![Page 4: Drill Press Safety PPT](https://reader034.fdocuments.us/reader034/viewer/2022052117/546776d4af79597c418b5d16/html5/thumbnails/4.jpg)
Make all adjustments (other than speed Make all adjustments (other than speed control) when the power is off and the control) when the power is off and the machine is at a dead stop.machine is at a dead stop.
This is on the Safety Test
![Page 5: Drill Press Safety PPT](https://reader034.fdocuments.us/reader034/viewer/2022052117/546776d4af79597c418b5d16/html5/thumbnails/5.jpg)
Check to see that the speed Check to see that the speed setting is correct for your work. setting is correct for your work.
This is on the Safety Test
½”
Holes over ½ inch Holes over ½ inch should be bored at should be bored at the slowest speed.the slowest speed.
![Page 6: Drill Press Safety PPT](https://reader034.fdocuments.us/reader034/viewer/2022052117/546776d4af79597c418b5d16/html5/thumbnails/6.jpg)
Use only approved type bits. Bits Use only approved type bits. Bits with feed screws or excessive with feed screws or excessive length should not be used.length should not be used.
This is on the Safety Test
![Page 7: Drill Press Safety PPT](https://reader034.fdocuments.us/reader034/viewer/2022052117/546776d4af79597c418b5d16/html5/thumbnails/7.jpg)
Mount the bit to the full depth of the drill Mount the bit to the full depth of the drill shank into the chuck and center it. shank into the chuck and center it.
Remove the Key Remove the Key immediatelyimmediately
This is on the Safety Test
![Page 8: Drill Press Safety PPT](https://reader034.fdocuments.us/reader034/viewer/2022052117/546776d4af79597c418b5d16/html5/thumbnails/8.jpg)
Position the table and adjust the Position the table and adjust the feed stroke so there will be no feed stroke so there will be no possibility of the bit striking the possibility of the bit striking the tabletable
This is on the Safety Test
![Page 9: Drill Press Safety PPT](https://reader034.fdocuments.us/reader034/viewer/2022052117/546776d4af79597c418b5d16/html5/thumbnails/9.jpg)
Work that will be held by hand Work that will be held by hand should be center punchedshould be center punched
This is on the Safety Test
![Page 10: Drill Press Safety PPT](https://reader034.fdocuments.us/reader034/viewer/2022052117/546776d4af79597c418b5d16/html5/thumbnails/10.jpg)
Work should be placed on a wood Work should be placed on a wood pad when holes will go all the way pad when holes will go all the way through the work piece.through the work piece.
This is on the Safety Test
![Page 11: Drill Press Safety PPT](https://reader034.fdocuments.us/reader034/viewer/2022052117/546776d4af79597c418b5d16/html5/thumbnails/11.jpg)
Small and irregular shaped Small and irregular shaped pieces must be clamped to the pieces must be clamped to the table or held in a special fixture.table or held in a special fixture.
This is on the Safety Test
![Page 12: Drill Press Safety PPT](https://reader034.fdocuments.us/reader034/viewer/2022052117/546776d4af79597c418b5d16/html5/thumbnails/12.jpg)
Make sure no one but you is inside the Make sure no one but you is inside the operator’s zoneoperator’s zone
This is on the Safety Test
3 Feet 3 Feet
3 Feet 3 Feet
DRILLPRESS
![Page 13: Drill Press Safety PPT](https://reader034.fdocuments.us/reader034/viewer/2022052117/546776d4af79597c418b5d16/html5/thumbnails/13.jpg)
Feed the bit into the Feed the bit into the work with a smooth, work with a smooth, even pressure.even pressure.
This is on the Safety Test
When the hole is deep, withdraw the bit When the hole is deep, withdraw the bit frequently to clear the shaving and cool the bit.frequently to clear the shaving and cool the bit.
![Page 14: Drill Press Safety PPT](https://reader034.fdocuments.us/reader034/viewer/2022052117/546776d4af79597c418b5d16/html5/thumbnails/14.jpg)
When using special clamping When using special clamping setups have the teacher inspect it setups have the teacher inspect it before turning on the power.before turning on the power.
![Page 15: Drill Press Safety PPT](https://reader034.fdocuments.us/reader034/viewer/2022052117/546776d4af79597c418b5d16/html5/thumbnails/15.jpg)
Turn off the power when done using Turn off the power when done using the drill pressthe drill press
Stand by the machine until it comes Stand by the machine until it comes to a complete stop.to a complete stop.
![Page 16: Drill Press Safety PPT](https://reader034.fdocuments.us/reader034/viewer/2022052117/546776d4af79597c418b5d16/html5/thumbnails/16.jpg)
Clean off the machine only when it Clean off the machine only when it is at a dead stop.is at a dead stop.
![Page 17: Drill Press Safety PPT](https://reader034.fdocuments.us/reader034/viewer/2022052117/546776d4af79597c418b5d16/html5/thumbnails/17.jpg)
Speed Control
ON / OFF Switch
Depth Stop
Quill / Chuck
Table
Base
Pilot Feed Wheel
Motor
Column
Typical Drill Press Typical Drill Press PartsParts
![Page 18: Drill Press Safety PPT](https://reader034.fdocuments.us/reader034/viewer/2022052117/546776d4af79597c418b5d16/html5/thumbnails/18.jpg)
Our Drill Our Drill PressPress
Table Height Adjustment
Table Adjustment Lock
Table
Pilot Feed Wheel
Speed Control
ON / OFF
Quill / Chuck