8/13/2019 Domorepair en 2013

1/2

QUICK SETTING REPAIRING ANCHORING MORTAR

DOMOREPAIR

DOMOREPAIR is a quick-setting, ready to use mortar. A product suitable for repairing, anchoring,

waterproofing, architectural details, concrete.

DOMOREPAIRis used:

- In any concrete repair as industrial floors,motorways, bridges, sewage pipes, boardwalks, etc.

- For damaged corner and finishing repairs.

- For filling cavities, cracks, small holes, etc.

- At the joints of prefabricated elements.

- For placing all kinds of anchoring like hooks, steel

rods, etc.

DOMOREPAIR is also suitable for leveling surfaces

prior to treatment with SERITAL.

Excellent adhesion on the substrate, due to its composition oforganic polymers and synthetic resins. .

Minimizes danger of cracking.

Quick and easy to use.

Economical.

High initial strength.

Excellent results at assembling.

Waterproof, freeze & weather resistant after hardening.

Does not contain chlorides or other corrosive salts.

High compressive strength.

Ready to use. Just add water.

APPLICATION FIELDS ADVANTAGES

Substrate PreparationThe application surface (concrete, mortar, stone,

brick) must be sound and stable.

Loose parts, rust, grease, dust and cement skin must

be removed prior to application. Wet well the

substrate with water prior to application.

METHO OF USE

8/13/2019 Domorepair en 2013

2/2

For a volume of 1 lt, about 1,7 kg of DOMOREPAIR are required.

DOMOREPAIR is stored for 12 months in a cool place, protected

from humidity in its original packing.

Bags of 25 kgr.

CONSUMPTION

PACKING

STORAGE

APPLICATION

When repairing elements of great thickness (more than 1-2

cm) apply in layers. Each layer is applied after the previous one

is hardened.

To avoid too fast setting of the already applied mix and to

prevent crack forming, protect the treated surface with a wet

cloth or wet it with water.

For vertical surfaces or overhead work, prepare a thick mix

with a ratio of 1:4. For special applications, please consult our

Technical Department. Setting starts after 10-15 min at 20C

and ends after 30-35 min.

Setting time is increased when the temperature is low or

when more water is added than necessary.

Form

Color

Specific weight

Resistance to low temperature

Humidity behaviour

Physiological effect

Toxicity

Setting time(at20'C)

Application temperature

Substrate temperature

powder

grey

1,4 kg/lt

down to -50 C

lightly hygroscopic

same as cement

non toxic

setting start10'-15',

setting end30 '-35 '

5- 35C

not below +5C

TECHNICAL SPECIFICATION

Put water in a suitable pail and add the DOMOREPAIR powder

Mix well until the blend is homogenuous..

Mixing ratio: about 1 part water to 3-4 volume parts DOMO-

REPAIR. Optimal mixing is achieved using a low power

agitator.

Apply the mix by brush, spatula, trowel or hand, depending on

the situation.

When repairing corners and edges, it is recommended to use

wood formwork until the hardening of DOMOREPAIR.

Do not mix more product that intend to use.

Do not add cement, sand or gravel to DOMOREPAIR.

MIXING INSTRUCTIONS

DOMOREPAIR

DOMISSIMA S.A.th

30 km. Thessaloniki - N. Moudanion Road,P.O.Box 306, GR 630 80, Lakkoma Chalkidiki,

Tel.: +30 23990 20320, Fax : +30 23990 20323www.domissima.gr, E-mail:info@domissima.gr

DOMISSIMACHEMIC L BUILDING M TERI LS SPECI L CONSTRUCTIONS

All the technical data stated in the present Technical Data Sheet are based on laboratory

tests and the knowledge and experience of the company. Different conditions may

apply at field applications that are beyond the control of the company. Therefore, the

end user is ultimately responsible to make sure that the product is suitable for the

application in question and to know the real conditions of the project.