Doc.: IEEE 802.11-11/1034r0 Submission Peng Xiaoming, I2R China WPAN mmWave Liaison w/ 802.11 Date:...
-
Upload
miguel-woodward -
Category
Documents
-
view
223 -
download
0
Transcript of Doc.: IEEE 802.11-11/1034r0 Submission Peng Xiaoming, I2R China WPAN mmWave Liaison w/ 802.11 Date:...
doc.: IEEE 802.11-11/1034r0
Submission Peng Xiaoming, I2R
China WPAN mmWave Liaison w/ 802.11 Date: 2011-07-19
Name Company Address Phone email Xiaoming Peng Institute for
Infocomm Research (I2R)
1 Fusionopolis Way, #21-01 Connexis, Singapore
65-6408-2429
Hong Wei Southeast University
State Key Laboratory of Millimeter Waves, Nanjing, 210096, P. R. China
Liang Li Vinno Technologies Inc
No.2 Shangdi XInxi Lu, Beijing, 100085, China
1-949-813-7909
Zhuo Lan CESI [email protected]
Authors:
Slide 1
doc.: IEEE 802.11-11/1034r0
Submission Peng Xiaoming, I2R
Outline
• CWPAN Structure
• CWPAN 60G update
• CWPAN Q-LINKPAN update
• Conclusion
Slide 2
doc.: IEEE 802.11-11/1034r0
Submission Peng Xiaoming, I2R
Overview of China WPAN (CWPAN)
• China Wireless Personal Area Network (CWPAN) working group was launched on December 2005. The meeting is held quarterly. (www.nits.gov.cn/wpan)
• CWPAN 60GHz project group (PG4) on “Gigabit Wireless Network in 60GHz bands” was launched in March 2010.
• CWPAN Q-LINKPAN study group (SG5) on “Gigabit Wireless Network in 40-50GHz bands” was launched in Sept 2010.
• Chinese Standards Organization
Slide 3
doc.: IEEE 802.11-11/1034r0
Submission Peng Xiaoming, I2R
CWPAN Meeting update
• The past CWPAN meeting (21th) was held in Neimenggu, China in June 21-23, 2011– There were 22 participants from 14 organizations– Received 12 technical proposals in PG4 (60GHz)– Received 2 proposals in SG5 (Q-LINKPAN (40-50GHz))
• The next CWPAN meeting (22th) will be held in Chengdu, China in Oct 24-25, 2011
Slide 4
doc.: IEEE 802.11-11/1034r0
Submission Peng Xiaoming, I2R
Overview of CWPAN PG4 – 60GHz • Objective
– The 60GHz Project Group for China Wireless Personal Area Networks (C-WPANs) is to define a project for a PHY, MAC operating in China’s unlicensed 60GHz spectrum• Timeline
Time Meeting Schedule Remarks
2010.3 16th PG work plan Completed
2010.6 17th Define Functional Requirement Document, Issue CFP
Completed
2010.9 – 2011.6
18th -21th Technical proposal presentation Received 34 technical proposals
2011.9-2011.12
22th-23th Technical proposal presentation Deadline to accept new technical proposals
2012.12 …. Technical specification submit for approval
doc.: IEEE 802.11-11/1034r0
Submission Peng Xiaoming, I2R
Introduction• The released 60GHz spectrum in China only has 5GHz bandwidth,
corresponding to channel 2 & 3 used in IEEE 802.11ad/WiGig.
• According to CWPAN 60GHz functional requirement document, it is required to support at least 3 logical channels for CWPAN network.
USA, Canada, Korea
Europe
China
Japan
Australia
Slide 6
doc.: IEEE 802.11-11/1034r0
Submission Peng Xiaoming, I2R
Proposed Channelization for CWPAN • In view of the available bandwidth in China and the requirement of CWPAN networking,
it has been proposed the following channelization for consideration in CWPAN
Co-existence When CWPAN device operates in small bands, there is a potential co-existence problem between CWPAN device and IEEE 802.11ad / WiGig device.
Slide 7
doc.: IEEE 802.11-11/1034r0
Submission Peng Xiaoming, I2R
Motivation• CWPAN intends to provide design to support dynamic
bandwidth – Backward compatibility: to keep the backward compatibility to
IEEE 802.11ad/WiGig device
– Coexistence: to ensure the coexistence between IEEE 802.11ad / WiGig device and CWPAN device
– PHY design: to reuse the PHY design for large bandwidth and reuse or change the PHY design for small bandwidth
– MAC design: There is a need to add in MAC protocols in CWPAN to split a large band into two small bands for operations of 2 networks and to expand a small band in network operation with an adjacent vacant small band into a large band.
Slide 8
doc.: IEEE 802.11-11/1034r0
Submission Peng Xiaoming, I2R
CWPAN MAC Protocols – to support dynamic bandwidth• When a new CWPAN device (to become AP/PCP2) requests an existing CWPAN network
(AP/PCP 1) to be split to a smaller band from a large band L1, it first joins the existing CWPAN network and requests to split the band
• After splitting, AP/PCP 1 and AP/PCP 2 each creates a quiet period (QP) in their respective networks and sends out quasi-omni beacons during notification period (NP) respectively.
• AP/PCP 2 synchronizes with AP/PCP 1 by receiving the time stamp in AP/PCP 1’s quasi-omni beacons during NP1.
• Non-AP/non-PCP devices associated to AP/PCP 1 continue their packet transmissions in small band network in S5 after tuning in and receiving the quasi-omni beacon frames sent out by AP/PCP 1 in small band. Non-AP/non-PCP devices associated to AP/PCP 2 start their operation in small band S6.
• When one network operating in small band ceases its operation, another network can proceed to expand its bandwidth from its small band to the large band after detecting it.
DTTAP/PCP1 S5
AP/PCP2 S6
BTI A-BFT DTTAT
VBI
BTI A-BFT AT DTT
SBBI at S6
SBBI at S5
NP
NP1 NP2
QP1
BTI A-BFT AT DTT
SBBI at S6
QP2
BTI A-BFT AT
SBBI at S5
Notification Period(NP) for PCP/AP 1
Notification Period (NP) for PCP/AP 2
Guard Interval(GI)
Revised Frame Structure in Dynamic Bandwidth MAC protocol for CWPAN network
Channel
doc.: IEEE 802.11-11/1034r0
Submission Peng Xiaoming, I2R
Quasi-Omni Beacon Format used in NP
• It uses the standard Beacon format except the following– Body of the DBand Beacon frame
• Beacon Interval Control– Use two reserved bits to indicate CWPAN Channel Bandwidth
Next A-BFTFragmented
TXSSTXSS Span
N Bis A-BFT
A-BFT count
N A-BFT in Ant
PCP Assoc Ready
CWPAN Channel
Bandwidth
6 1 7 3 6 6 1 2Bits
B15-20 B21 B22-28 B29-31 B32-37 B38-43 B44 B45-46
CC presentDiscovery
ModeNext
BeaconAT
PresentA-BFT Length
FSS isResponderTXSS
1 1 4 1 4 3 1Bits
B0 B1 B2-5 B6 B7-10 B11-13 B14
Reserved
B47
1
Beacon Format
Beacon Interval Control FieldSlide 10
doc.: IEEE 802.11-11/1034r0
Submission Peng Xiaoming, I2R
Minimal Change in IEEE 802.11ad
• For co-existence between IEEE 802.11ad and CWPAN, there is a minimal change in IEEE 802.11ad
– Request to use two reserved bits in Beacon Interval Control Field to communicate for CWPAN Channel Bandwidth
Next A-BFTFragmented
TXSSTXSS Span
N Bis A-BFT
A-BFT count
N A-BFT in Ant
PCP Assoc Ready
CWPAN Channel
Bandwidth
6 1 7 3 6 6 1 2Bits
B15-20 B21 B22-28 B29-31 B32-37 B38-43 B44 B45-46
CC presentDiscovery
ModeNext
BeaconAT
PresentA-BFT Length
FSS isResponderTXSS
1 1 4 1 4 3 1Bits
B0 B1 B2-5 B6 B7-10 B11-13 B14
Reserved
B47
1
Beacon Interval Control Field
Slide 11
doc.: IEEE 802.11-11/1034r0
Submission Peng Xiaoming, I2R
Overview of CWPAN SG5 – 40~50GHz In 2009, a big fundamental research project supported by the MOST of
China on CMOS Millimeter Wave and THz ICs was approved, the key application of the ICs is aimed for millimeter wave wireless communications.
Southeast University (SEU) delivered the proposals to CWPAN working group and the State Radio Regulatory Commission to develop the China mmW standard Q-LINKPAN which can be used both in short range and point-to-point (Q-Band + LINK +PAN).
A study group (SG5) was then set up under CWPAN in Sept 2010 to start the technical investigation on Q-LINKPAN.
The State Radio Regulatory Commission is now considering the application of frequency band for Q-LINKPAN.
Slide 12
doc.: IEEE 802.11-11/1034r0
Submission Peng Xiaoming, I2R
Background
Around60 GHz
Around 45 GHz
Slide 13
doc.: IEEE 802.11-11/1034r0
Submission Peng Xiaoming, I2R
The Advantages of Q - LINKPAN
For short range wireless communications, the cost of Q-LINKPAN products will be only around 70% of the cost of 60GHz products. Actually, for the same performance, 90nm CMOS process is necessary for 60GHz but 130nm CMOS process for Q-LINKPAN.
60GHz systems couldn’t be used for long distance point-to-point high data rate communication due to the atomspheric absorption peak at 60GHz band (~20dB/km). The low atomspheric absorption loss (~1dB/km) makes the Q-LINKPAN be easily used for point-to-point high data rate communication by high gain antennas.
For the same performance, the power consumption of Q-LINKPAN systems will be around 80% of 60GHz systems. Actually, for same coverage, the power required for Q-LINKPAN will be deceased around 20% compared with 60GHz systems.
For long distance point-to-point high data rate communication, the cost of Q-LINKPAN products will be only around 50% of the cost of E-band products.
Slide 14
doc.: IEEE 802.11-11/1034r0
Submission Peng Xiaoming, I2R
Roadmap of Q-LINKPAN
DraftDraftStudy Group
2009 2010 2011 2012 2013 2014
Transmitter
Receiver
PLL
Transceiver
BB
Transceiver
ASIC/BB
SoC
Standard
Q-LINKPAN Rx
Q-LINKPAN Tx
PLL
+RF ModuleRF Module
BasebandBaseband
Demo SystemDemo
SystemTape out
Q-LINKPANProducts
Slide 15
Standardization:
Prototype & Production:
doc.: IEEE 802.11-11/1034r0
Submission Peng Xiaoming, I2R
Request of Spectrum Allocation in 40-50GHz
• In April 2011, Prof. Hong Wei and the team reported to State Radio Regulatory Commission on the progress of CWPAN SG5 Q-LINKPAN and suggested the following options of spectrum allocation in 40-50 GHz– Option 1: 40GHz – 45GHz
– Option 2: 40GHz – 47GHz
– Option 3: 45GHz – 50GHz
• In July 2011, CWPAN plans to submit the official request to State Radio Regulatory Commission for spectrum allocation in 40-50 GHz– A Q-band (40-45.5 GHz) will be used for Q-LINK PAN
– Licensed 2 X 1.568 GHz band pair for Q-LINKPAN-L and unlicensed 2.24 GHz band for Q-LINKPAN-S
Slide 16
doc.: IEEE 802.11-11/1034r0
Submission Peng Xiaoming, I2R
Conclusions CWPAN has made significant progress in PG 4 (60GHz) and SG 5
(40~50GHz) in the last Quarter
CWPAN Co-existence proposal ensures the co-existence between CWPAN and IEEE 802.11ad networks Minimal change in IEEE 802.11ad
CWPAN has officially submitted the request of the spectrum allocation in 40-50 GHz in China for Q-LINKPAN
Slide 17
doc.: IEEE 802.11-11/1034r0
Submission Peng Xiaoming, I2R
Reference
1. NITS-10-45-02-WPAN(60G) – Channelization for CWPAN 60GHz
2. NITS-10-46-00-WPAN(60G) – Evaluation of PLL design for Dynamic Bandwidth
3. NITS-10-47-00-WPAN(60G) – Evaluation of ADC/DAC design for Dynamic Bandwidth
4. NITS-11-018-00-WPAN(60G) - A Design Consideration for Dynamic Bandwidth for CWPAN
5. NITS-11-027-00-WPAN(60G) - Dynamic Bandwidth Control MAC Protocols for Co-existence of Networks
6. NITS-11-014-00-WPAN(SG5) – Overview of Q-LINKPAN
Slide 18
doc.: IEEE 802.11-11/1034r0
Submission Peng Xiaoming, I2R
THANK YOU!!!
Slide 19