DIVERSIONSYSTEM - Agni Controlsbalafire.com/pdf/CO2.pdf · TEXTILE FIRE PROTECTION SYSTEM...
Transcript of DIVERSIONSYSTEM - Agni Controlsbalafire.com/pdf/CO2.pdf · TEXTILE FIRE PROTECTION SYSTEM...
No:1, 6 Street, Dr. Subbarayan Nagar, Kodambakkam, Chennai - 600 024, IndiaPhone: +91- 44-24812420; Fax: +91- 44- 24812475
E-mail: [email protected], [email protected]; Website: www.balafire.com
th
DIVERSION SYSTEM
Fire Detection and Diversion System
Introduction :-
In Textile Plant, particularly Spinning Industry, normally Blow room is connected withCarding section and Filter section through material duct, dust duct and waste duct.
If Spark is created while processing the cotton in Blow Room, which travels through duct andspread to Carding and Filter area.
It is always the concept to detect the fire at early stage and confine the fire in one area/ zone andextinguishing the fire within the area / zone.
FireDiversion System is basically designed on the above discussed principle.
:-
1.) Fire Detection,2.) Isolating the Fire by stopping themachineries and operating the Dampers,3.) Diversion Dampers stop thematerial flow and divert thematerial into
Diversion Duct,4.) DivertedMaterials sucked through Suction Fan toQuenching Tank or Fire Collection Bag,5.) Extinguishing BurningMaterial.
1.) FireAlarm Control Panel.2.) Electrical Trip Panel.3.) Pneumatic Control Panel.4.) Spark Detector.5.) Heat Detector.6.) Electronic Hooter.7.) Fire Stop Damper.8.) Fire Diversion Damper.9.) PneumaticActuator.10.) Quenching Tank.11.) DiversionDuct&SuctionFan.
Fire can be detected either by Spark Detector or Heat Detectors. Fire can be detected by fixing theHeat Detectors of 60 C. Temp. range in the Machinery enclosure and duct. The spark detector is placed inthematerial duct and dust duct which passes through the carding & filter area.
SystemOperation
The following activities are the key function of the system.
System Consists of :-
Fire Detection :-
°
Page 1 of 4
Heat Detector is fixed temperature bi-metal type which operates effectively in any type ofenvironmental condition. Spark Detectors are available with higher efficiency to detect the movingspark in the duct. However direct exposure of day light and sun light may create false alarm. Properprecaution has to be adopted while installing the spark detector in the duct. Our Spark DetectorAssemblyconsists of 4 Nos./5 Nos. of Infra Red Spark Detectors fixed at 90°/72° angle to cover entire duct.
In our system we have adopted necessary precaution to avoid false fire alarm and to give the bestefficient detection method.
Fire Alarm Control Panel is the back bone of the entire system which gives input to the detectorand receives the signal from the detectors. It gives audio visual fire indication and also trip machines asper the system requirement and actuates the solenoid to supply the compressed air to the pneumaticactuator to operate Diversion Dampers pneumatically. The Control Panel works with 230 V AC primaryinput supply and 24 V DC secondary battery back up. The entire system works with 24 V DC.
FireAlarmControl Panel
No:1, 6 Street, Dr. Subbarayan Nagar, Kodambakkam, Chennai - 600 024, IndiaPhone: +91- 44-24812420; Fax: +91- 44- 24812475
E-mail: [email protected], [email protected]; Website: www.balafire.com
th
DIVERSION SYSTEM
Page 2 of 4
No:1, 6 Street, Dr. Subbarayan Nagar, Kodambakkam, Chennai - 600 024, IndiaPhone: +91- 44-24812420; Fax: +91- 44- 24812475
E-mail: [email protected], [email protected]; Website: www.balafire.com
th
DIVERSION SYSTEM
Page 3 of 4
FIRE ALARM CUM DIVERSION PANELSPECIFICATION;-
1. Location - Indoor2. Colour - Fire Red3. Painting Process - Powder Coating Process4. Protection Class - IP 525. Description - Fire Alarm cum Pneumatic
Control Panel with Electromagneticrelays for Auxiliary SwitchingContacts. 16 SWG M.S SheetWall Mounting Type.
6. Application - Diversion System7. Power Source - Input Supply Voltage 230V, 1PH,
50 Hz AC Working VoltageDerived will be 24V DC, 10 Amps.
8. Operating Voltage - 24V DC9. Supply Voltage & Source to Detector - 22V DC10. Signal Voltage on Control Panel - 12V DC
SPARK DETECTORSPECIFICATION;-
1. Application - It is designed to fix the Duct to Detect Fire.2. Colour - Fire Red3. Painting Process - Coating Process4. Supply Voltage - 20V DC to 24V DC5. Quicent Current - 5mA6. Alarm Current - 30mA to 100mA7. No. of Sensor - 4 Nos.8. Operating Temp. Range - 0 C to 60 C9. Principle of Detection - IR Detection Technology10. Response Indication - Two Red LED per Module
° °
HEAT DETECTORSPECIFICATION;-
1. Application - It is designed to fix the Duct to Detect Heat.2. Supply Voltage - 18V DC to 24V DC3. Quicent Current - 1.2mA4. Alarm Current - 45mA5. Detector Setting Temp. - 60 C6. Principle of Detection - Bi - Metal Principle7. Response Indication - Two Red LED
°PLAN
IR DETECTOR
FRONT VIEW
No:1, 6 Street, Dr. Subbarayan Nagar, Kodambakkam, Chennai - 600 024, IndiaPhone: +91- 44-24812420; Fax: +91- 44- 24812475
E-mail: [email protected], [email protected]; Website: www.balafire.com
th
DIVERSION SYSTEM
Page 4 of 4
ELECTRONIC HOOTER WITHFLASHING LAMP
SPECIFICATION;-
1. Mounting Type - Wall Mounting Type.2. Colour - Fire Red3. Painting Process - Powder Coating4. Cable Entry - Bottom5. Working Voltage - 24V DC6. Current Consumption - 100mA Max.7. Type of Tone - Dual Tone
FIRE STOP DAMPERSPECIFICATION;-
1. Damper Material - 3.15mm - 10SWG, H.R Sheet2. Flap Thickness - 4mm Thickness M.S Sheet3. Colour - Fire Red4. Painting Process - Powder Coating5. Actuation - Pneumatic Operation
- Reset from Control Panel
FIRE DIVERSION DAMPERSPECIFICATION;-1. Damper Material - 3.15mm - 10SWG, H.R Sheet2. Flap Thickness - 4mm Thickness M.S Sheet3. Colour - Fire Red4. Painting Process - Powder Coating5. Actuation - Pneumatic Operation
- Reset from Control Panel
QUENCHING TANKSPECIFICATION;-
1. Material - M.S Plate2. Thickness - 5mm Thickness3. Capacity - 1000 Litres / 2000 Litres
Actuator Working Condition(Diversion Duct Open Condition)
Flap Normal Condition(Diversion Duct Closed Condition)
Pneumatic ActuatorReducer
Flap Normal Condition( Duct Open Condition)
Actuator Working Condition( Duct Closed Condition)
Quenching Tank
Front View Side View
Buzzer
Flash Lamp
No:1, 6 Street, Dr. Subbarayan Nagar, Kodambakkam, Chennai - 600 024, IndiaPhone: +91- 44-24812420; Fax: +91- 44- 24812475
E-mail: [email protected], [email protected]; Website: www.balafire.com
th
CO2 FLOODING SYSTEM
TECHNICAL REVIEW ON STANDARD CO2 FIRE EXTINGUISHING SYSTEM
Page 1 of 3
Introduction
Scope of our offer
System Description
bala-wa CO Flooding Fire Extinguishing system & Components are engineered, designed,manufactured / procured to meet NFPA-12 / IS15528 : 2004 standards.
The scope of this offer is supply of CO2 Fire Protection System for Machineries as per your enquiry.Independent CO2 Cylinder banks are considered for this offer to protect specified area as per thespecification.
High pressure CO2 System is offered. The system consists of the followingmaincomponents.68 Ltrs.W/CSeamless CO2 Cylinder to fill 45Kg CO2 gas.Master & Slave CO2 Cylinder Valves.Discharge & Actuation Hoses.CO2 FrameAssembly with Manifold.CO2 Discharge Nozzles.FireAlarm cum Gas Discharge Panel.ManualGasDischarge Station.Electronic Hooter with Flashing Lamp.Discharge Warning Display Board.
Cylinder bank, consisting of required Nos. of 45 Kg Gas capacity CO2 Cylinders. First cylinder ofCylinder bank will be fitted with 24 V DC Solenoid operated master valve. Remaining cylinders willbe fitted with pneumatically operated slave valves. From the cylinder valves ½” H.P Dischargehoses will be connected to CO Manifold through NRV. Actuation hoses will be connected fromMaster NRV to slave valve. Seamless Sch.80 pipes will be connected from the manifold todischarge nozzles.Required Spark & Heat Detectors along with Manual Gas Discharge Stations, External Hooter, withDischarge Warning Display Board will be provided at the entrance of the each ProtectedArea.Fire Alarm Panel & Gas discharge panel will be provided for interconnecting the Detection signalfrom Detectors and other instruments.
2
2
1.
2.
3.
4.
5.
6.
7.
8.
9.
No:1, 6 Street, Dr. Subbarayan Nagar, Kodambakkam, Chennai - 600 024, IndiaPhone: +91- 44-24812420; Fax: +91- 44- 24812475
E-mail: [email protected], [email protected]; Website: www.balafire.com
th
CO2 FLOODING SYSTEM
Page 2 of 3
The system can be operated by any one of the followingmethod.
1. Automatic detection and automatic extinguishing.2. Manual detection and Manual discharge through Manual Gas Discharge Stations3. Mechanical Manual discharge by operating manual release lever
On receipt of signal from any : 1. Inbuilt Fire Hooter ON.spark / Heat detector 2. External Hooter ON.
3. Fire Signal will be provided to GasDischarge Panel.
4. Delay Timer ON.5. Tripping signal will be provided.
After the lapse of preset time delay, Gas Discharge Panel will send 24V DC supply to SolenoidValve of master cylinder valve . Solenoid valve will open the master valve and CO will bedischarged to manifold through discharge hose and master NRV.
Further entire gas will be discharged to Protected area discharge nozzle by using distribution pipingfrom the discharge header. Pressure switch, which is fitted on manifold, will be actuated due to theavailability of the pressurized gas in the CO manifold. Simultaneously it will send gas dischargeindication to control panel.
During the actual Fire condition, without waiting for actuation of detectors, Fire signal can beprovided to control panel for discharging the CO2 gas to the protected area, by breaking Glass andpressing both the discharge push button simultaneously. If we press both the push buttonssimultaneously, the same will be treated, as a Fire Signal and the other function will be done asexplained above.
Apart from the above two methods, CO2 cylinder can be opened by pressing the manualreleasing knob of master cylinder valves.
Automatic detection and automatic extinguishing
•
2
2
Manual detection andManual discharge by through Manual Call Point
Mechanical Manual discharge by operating manual release lever
No:1, 6 Street, Dr. Subbarayan Nagar, Kodambakkam, Chennai - 600 024, IndiaPhone: +91- 44-24812420; Fax: +91- 44- 24812475
E-mail: [email protected], [email protected]; Website: www.balafire.com
th
CO2 FLOODING SYSTEM
PROTECTION OF BLOW ROOM MACHINERIESWITH
CO2 FLOODING FIRE EXTINGUISHING SYSTEM
Page 3 of 3
Doc.No.: 093/06-07 3/4Date.: 01/10/2006
Sl.No. Part No.
1 IH147
2 IH040
3 IH042-60
4 IH042-70/80
5 IH148
6 IH148/1
7 IH163/1
8 IH163/2
9 IH163/3
10 IH163/4
11 IH163/6
12 B228S
13 IH140
14 IH141
15 IH039W
16 IH046/Z4/T4
17 IH046/Z6/T6
18 IH046/Z8/T8
19 IH046/Z10/T10
20 IH046/Z*/T*
21 IH171
22 IH172
23 IH173
24 IH174
25 IH227
26 IH175
27 B232
28 B214
29 B215
30 B229
31 B231/*
32 B233
33 B235
34 IH221/1 Pneumatic Panel with one set of actuations, Each set can operate Two Dampers
Conventional Modular Type Fire Alarm Panel with Pneumatic Actuation Module to Operate Dampers (* - As per Requirement)
2x12V DC, *AH SMF Lead Acid Battery
4 zone Conventional Modular Type Fire Alarm Panel with Pneumatic Actuation Module to Operate 4 Dampers
6 zone Conventional Modular Type Fire Alarm Panel with Pneumatic Actuation Module to Operate 6 Dampers
8 zone Conventional Modular Type Fire Alarm Panel with Pneumatic Actuation Module to Operate 8 Dampers
10 zone Conventional Modular Type Fire Alarm Panel with Pneumatic Actuation Module to Operate 10 Dampers
Nylon Hose
Quenching Tank - 1000 Ltrs. Capacity
2Cx1.5 Sq.mm Cu.Armd. FRLS Cable
Fire Stop Dampers with Reducers and Match Rings suitable to fix in 200 - 350mm Dia Ducts
Fire Stop Dampers with Reducers and Match Rings suitable to fix in 400 - 500mm Dia Ducts
Fire Stop Dampers with Reducers and Match Rings suitable to fix in 500 - 600mm Dia Ducts
Pneumatic Actuator suitable for Part.NoIH171, IH172, IH173 & IH174 - Working Pressure of 4 - 10 bar.
Fire Diversion Dampers with Reducers and Match Rings suitable to fix in 200 - 350mm Dia DuctsMetal Diversion Dampers with suitable accessories suitable for 300mm Dia Ducts
4Cx1.5 Sq.mm Cu.Armd. FRLS Cable
Suction Fan
IR Spark Detector Module stand alone unit suitable for Mounting Directly on Duct / Machinery.
TEXTILE FIRE PROTECTION SYSTEM COMPONENTS
Description
Electronic Dual Tone Hooter with Flashing Lamp for Indoor Application.
Probe type heat detector with ordinary junction box - 60 Deg.C Temparature Setting
Probe type heat detector with ordinary junction box - 70 Deg.C / 80 Deg.C Temparature Setting
Fixed Temparature Bi-Metal & Auto Reset type Heat Detector - 60 Deg.C Temparature setting with Dual LED indication suitable for wall or surface mounting type.
Electronic Hooter Dual Tone - For Indoor Application
Fusible Bulb type Link for Fire Proof Door - 68° C Temp. Setting
Manual Call Point - Break Glass Type with canopy & hammer for outdoor application
Fixed Temparature Bi-Metal & Auto Reset type Heat Detector - 60 Deg.C Temparature setting with Dual LED indication suitable for duct mounting type.
IR Spark Detector Assembly suitable for Duct Size upto 400mm Dia
IR Spark Detector Assembly suitable for Duct Size above 400mm Dia upto 600mm Dia
IR Spark Detector Single Module suitable for part No.IH163/1, IH163/2 as spares.
Electrical trip panel with 8 outputs
IR Spark Detector Module - Weather Proof Model
Metal Detector with suitable accessories suitable for 300mm Dia Ducts
Siren Control Panel
Page : 1 of 1Ph No : + 91 44 24812420 Fax : + 91 44 24812475
E-Mail : [email protected]@agnicontrols.com
SPARK DETECTOR ASSEMBLY
PART NO : IH-163/1
IH163/1 Spark Detector is Designed to use in Duct of
various sizes for Textile Industries or other similar
Industries, where the possibility of Fire Spread through
duct from one area to other. It consist of 4 Spark
Detectors module placed in 90 Deg. Spacing.
The IR Spark Detector individual module has wide
angular sensitivity and can reliably and quickly detect
Amber in motion.
IR Spark Detector is active in the range of 400 nm to 1100
nm.
Each individual module is fully wired and is properly fixed
with suitable filter to avoid damage due to movement of
seed, stone and other hard particles in the duct.
Fully wired Spark Detector Assembly is designed to
connect directly with FireAlarm Control Panel.
1. In Textile Spinning Mills Blow Room Machineries can
be protected by detecting Fire in the duct using Spark
Detector.
2. Carding and Filter Machineries can be protected by
fixing Spark Detector in the duct.
3. Paper and Wood Industries dust duct finds IR Spark
Detector application.
Application:-
IH163/1 Spark Detector is Designed to use in Duct of
various sizes for Textile Industries or other similar
Industries, where the possibility of Fire Spread through
duct from one area to other. It consist of 4 Spark
Detectors module placed in 90 Deg. Spacing.
The IR Spark Detector individual module has wide
angular sensitivity and can reliably and quickly detect
Amber in motion.
IR Spark Detector is active in the range of 400 nm to 1100
nm.
Each individual module is fully wired and is properly fixed
with suitable filter to avoid damage due to movement of
seed, stone and other hard particles in the duct.
Fully wired Spark Detector Assembly is designed to
connect directly with FireAlarm Control Panel.
1. In Textile Spinning Mills Blow Room Machineries can
be protected by detecting Fire in the duct using Spark
Detector.
2. Carding and Filter Machineries can be protected by
fixing Spark Detector in the duct.
3. Paper and Wood Industries dust duct finds IR Spark
Detector application.
Application:-
Maintenance & Inspection :-
Installation Consideration :
To assure maximum sensitivity, keep the surface
of the sensor clean from dirt or other contaminants
at all times.
Periodically test the sensitivity of the detector
using small Amber through specially provided
inspection hole.
IH163/1, must be installed such that no external
light reaches the sensor. External Light source can
cause False FireAlarm.
Maintenance & Inspection :-
Installation Consideration :
To assure maximum sensitivity, keep the surface
of the sensor clean from dirt or other contaminants
at all times.
Periodically test the sensitivity of the detector
using small Amber through specially provided
inspection hole.
IH163/1, must be installed such that no external
light reaches the sensor. External Light source can
cause False FireAlarm.
IH - 163/1 SPARK DETECTORASSEMBLY
IH - 163/1 SPARK DETECTORASSEMBLY
Advantages :
�
�
�
�
�
�
�
Rigid Model to be used in changing environment.
Fast Responses to Amber/Spark / Flame in moving
Inspection hole is provided to check the Periodically
performance of all the IR Spark Detector modules.
Easy to install and operate
High Speed Response
Free from FalseAlarm
Low Maintenance Cost
Advantages :
�
�
�
�
�
�
�
Rigid Model to be used in changing environment.
Fast Responses to Amber/Spark / Flame in moving
Inspection hole is provided to check the Periodically
performance of all the IR Spark Detector modules.
Easy to install and operate
High Speed Response
Free from FalseAlarm
Low Maintenance Cost
Technical Specifications
PARAMETERS RATING UNITS
SUPPLY VOLTAGE 18 - 28 V DC
NO. OF SENSOR UNIT 4 Nos.
SENSOR TYPE IR -
SENSOR RANGE 400 nm TO 1100 nm NANOMETER
MAKE & MODEL SIEMENS ( E 9087)GERMANY / FAIR CHILD -(QSE) USA
QUIESCENT CURRENT < 6 ma
ALARM CURRENT 60 (MAX) ma
FIRE INDICATION RED LED -
MATERIAL MS SHEET 1.6 mm -
CABLE ENTRY ¾ ' -
WIRING 2 WIRE OF MIN1 Sq. mm SIZE -
OPERATING 0° ~ 60° °cTEMPERATURE
FINISHING RED COLOURPOWDER COATING -
<
Technical Specifications
PARAMETERS RATING UNITS
SUPPLY VOLTAGE 18 - 28 V DC
NO. OF SENSOR UNIT 4 Nos.
SENSOR TYPE IR -
SENSOR RANGE 400 nm TO 1100 nm NANOMETER
MAKE & MODEL SIEMENS ( E 9087)GERMANY / FAIR CHILD -(QSE) USA
QUIESCENT CURRENT < 6 ma
ALARM CURRENT 60 (MAX) ma
FIRE INDICATION RED LED -
MATERIAL MS SHEET 1.6 mm -
CABLE ENTRY ¾ ' -
WIRING 2 WIRE OF MIN1 Sq. mm SIZE -
OPERATING 0° ~ 60° °cTEMPERATURE
FINISHING RED COLOURPOWDER COATING -
<
Important :
This document is not intended to be used for installation purposes.Specifications are subject to change without prior notice.
Important :
This document is not intended to be used for installation purposes.Specifications are subject to change without prior notice.
M/s. Agni Controls,No :1, 6th street, Dr.Subbarayan Nagar, Kodambakkam,Chennai - 600024, IndiaPH : +91-44-24812420 FAX : +91-44-24812475Website : www.balafire.comE-mail : [email protected]
M/s. Agni Controls,No :1, 6th street, Dr.Subbarayan Nagar, Kodambakkam,Chennai - 600024, IndiaPH : +91-44-24812420 FAX : +91-44-24812475Website : www.balafire.comE-mail : [email protected]
CUSTOMER LIST – TEXTILES DIVERSION SYSTEM (WITH TAC APPROVAL)
Sl. No. CUSTOMER PLACE M/c NAME STATUS
01. Century Textiles-Zenith Unit Bombay Trumac Completed
02. Tamil Nadu Jai Bharath Aruppukottai LMW Completed
03. Prime Cotton Textiles Coimbatore Trumac Completed
04. Textool Company Ltd. Coimbatore LMW Completed
05. Century Unit Bombay Trumac Completed
06. Century Yarn Indore Trumac Completed
07. Gem Spineers Madras Trutzschler Completed
08. Sri Jayajothi & Co. Ltd. Rajapalayam LMW Completed
09. Prima Products Pvt. Ltd. Coimbatore Trumac Completed
10. Lakshmi Narashimha Textiles Coimbatore Trumac Completed
11. Kallam Spinning Mills Ltd. Guntur Trumac Completed
12. DCM Clusion Spinning Mills Ltd. New Delhi LMW Completed
13. Patspin India Ltd. Palakkad Trumac Completed
14. Sri Vishnu Shankar Mills Ltd. Rajapalayam LMW Completed
15. Palani Andavar Mills Ltd. Udamalpet LMW Completed
16. Jai Mata Industries Ltd. Rohtak LMW Completed
17. Prime Cotton Textiles Coimbatore Trumac Completed
18. Aruppukottai Shri Vijayalakshmi Aruppukottai LMW Completed
19. Dewan Textiles Ltd. Meerut LMW Completed
20. Malwa Cotton Spinning Mills Ltd. Ludhiana LMW Completed
21. Sudarsanam Spinning Mills Rajapalayam LMW Completed
22. Prakash Cotton Mills Ltd. Bombay Trumac Completed
23. Shreyans Spinning Mills Ludhiana LMW Completed
24. Auro Dyeing Ludhiana LMW Completed
25. Sri Aruppukottai Jayavilas Mills Aruppukottai LMW Completed
26. Auro Spinning Mills Ludhiana LMW Completed
27. Nagreeka Exports Ltd. Bombay LMW Completed
28. Sri Renuga Textiles Mills Ltd. Theni Trumac Completed
29. Pranavaditya Spinning Mills Bombay Trumac Completed
30. Euro Cotspin Ltd. New Delhi Cross Roll Completed
31. Vibha Synthetics Pvt. Ltd. Hinganghat LMW Completed
32. Mehala Carona Textiles Pvt. Ltd. Tirupur LMW Completed
33. Abhishek Industries Ltd. Barnala LMW Completed
34. Nahar Spinning Mills Phase I Mandideep LMW Completed
35. Nahar Spinning Mills Phase II Mandideep LMW Completed
36. Malwa Cotton Spinning Mills Paonta Sahib Trumac Completed
CUSTOMER LIST – TEXTILES DIVERSION SYSTEM (WITH TAC APPROVAL)
Sl. No. CUSTOMER PLACE M/c NAME STATUS
37. L.G.B. Industries Ltd. Karur Trumac Completed
38. Nahar Exports Ltd. Lairu LMW Completed
39. Raymonds Calltri Denim Ltd. Thane Trutzschler Completed
40. Sailakshmi Industries Pvt. Ltd. Bangalore Rieter Completed
41. Navnitlal Pvt. Ltd. Sarvoli Trutzschler Completed
42. Nahar Fibres Ltd. Ludhiana LMW Completed
43. Rohini Mills Tirupur LMW Completed
44. Hindoostan Spg. & Wvg. Mills Ltd. Mumbai Trumac Completed
45. Pondicherry Co -op. Spg. Mills Ltd. Pondicherry LMW Completed
46. Century Denim Indore Trumac Completed
47. Kamala Mills Ltd. Mumbai Trumac Completed
48. Shree Manufacturing Co. Ltd. Medak LMW Completed
49. R.S.R.Mohota Spg.&Wvg. Mills Ltd. Wani LMW Completed
50. Hindoostan Spg. Mills Ltd. (C Unit) Mumbai Trumac Completed
51. Annpurna Overseas Ltd. Panipet Trumac Completed
52. Mannan Cotton Spg. Mills Abiramam Trumac Completed
53. Mangrul Mills Nagpur LMW Completed
54. Vijayalakshmi Spintex Secunderabad Trumac Completed
55. Sri Jayajothi & Co. Ltd. Rajapalayam LMW Completed
56. Jayalakshmi Textiles Pvt. Ltd. Aruppukottai LMW Completed
57. Sri Nachiammal Cotton Mills Ltd. (B Unit) Chettinad LMW Completed
58. Sri Nachiammal Cotton Mills Ltd. (C Unit) Veeranam LMW Completed
59. Nav Maharashtra Sahakari
Soot Girani Ltd. Kolhapur Trumac Completed
60. Rishab Spg. Mills Ludhiana Trumac Completed
61. Nahar Spg. Mills Ltd. Phase III Mandideep LMW Completed
62. Sri Nachiammal Cotton Mills
Ltd. (A Unit) Chettinad Trumac Completed
63. Indo Count Industries Ltd. Kolhapur Rieter Completed
64. Patspin India Ltd. Palakkad Trumac Completed
65. Abhinav Cotspin Ltd. Batala Trumac Completed
66. Jaya Murugan Cotton Mills Ltd. Salem LMW Completed
67. Cheema Spintex Ltd. Chandigarh Rieter Completed
68. Satia Synthetics Ltd. Muktsar LMW Completed
69. Nahar Spg. Mills Ltd. (Phase II) Mandideep LMW Completed
70. Malkkal Fibres Ltd. Mhow Cross Roll Completed
CUSTOMER LIST – TEXTILES DIVERSION SYSTEM (WITH TAC APPROVAL)
Sl. No. CUSTOMER PLACE M/c NAME STATUS
71. Pacific Cotspin Ltd. Calcutta LMW Completed
72. R.M. Mohite Textiles Ltd. Kholapur LMW Completed
73. Prathibha Syntex Ltd. Indore Trumac Completed
74. G.T.N. Textiles Ltd. Nagpur Trumac Completed
75. Govardhan Spineers Ltd. Madurai Trumac Completed
76. Sree Nagalakshmi Textiles Ltd. Madurai Trumac Completed
77. Rishab Spinning Mills Ltd. Ludhiana Trumac Completed
78. Nahar Fibres Ltd. Malerkota LMW Completed
79. G.T.N. Textiles Ltd. Alwaye LMW Completed
80. Hindustan Fibres Ltd. Alwar Trumac Completed
81. Priyadarshini Fabs Ltd. Srivilliputhur Trumac Completed
82. Indo Count Choongnam Ind. Ltd. Baroda Trumac Completed
83. Armstrong Spg. Mills Ltd. Tirupur Trumac Completed
84. B.A.P.L. Industries Ltd. Coimbatore Trumac Completed
85. Nahar Spinning Mills Ltd., Mandideep Trumac Completed
86. Raymond Ltd., Yatmal ---- Completed
87. Visakha Industries Ltd., Nagpur (Moudha) Trumac Completed
88. Premier Mills Ltd., Hosur ---- Completed
89. Gem Spinners India Ltd., Chengalpet ---- Completed
90. LGB Textiles Karur ---- Completed
91. Satia Synthetics Mukstar ---- Completed
92. Nagreekara Exports Ltd., Kolhapur ---- Completed
93. Aravind Cotsyin (India) Ltd., Kolhapur ---- Completed.
94. Nahar Fibres Ltd., Ludhiana ---- Completed.
95. Rishab Spinning Mills Ludhiana …. Completed
96. Malwa Industries (Machchiwara) Ludhiana …. Under Commi.
Sl. No. Name of the Customer Place STATUS
1 Prima Products Pvt. Ltd., Coimbatore Completed
2 Janaki Raman Mills Ltd., Rajapalayam Completed
3 Jay Textiles (LMV Group) Coimbatore Completed
4 Madanapalle Mills Ltd. Madanapalli Completed
5 Tirupur Textiles Ltd., Tirupur Completed
6 Shree Kaderi Ambal Mills Pvt. Ltd. Karaikudi Completed
7 Shree Akkamamba Textiles Ltd. Tanuku Completed
8 Thiyagarajar Mills Ltd., Kappalur Completed
9 Shri Sivakami Mills Ltd., Madurai Completed
10 Premier Polytronics Ltd., Coimbatore Completed
11 Vijayashree Spg.Mills Ltd., Dindigul Completed
12 Visaka Industries Ltd. Nagpur Completed
13 Surya Jhothi Spg. Mills Ltd., Secunderabad Completed
14 Premier Mills Ltd. Udumalpet Completed
15 Palani Andavar Cotton & Synthetics Mills Ltd Udumalpet Completed
16 Indocount Industries Ltd., Kolhapur Completed
17 M/s. Oil India Ltd., Duliajan, Assam Completed
18 MID India Spg. Mills Ltd Mandasur Completed
19 The Dawn Mills Mumbai Completed
20 Defence Mettalurgical Ltd Hyderabad Completed
21 Shree Meenakshi Sundaram Textile Ltd Hosur Completed
22 Premier Products (P) Ltd. Coimbatore Completed
23 Oswal Cotton Spg. Mills Ludhiana Completed
24 Ashok Leyland Ltd Hosur Completed
25 Ennore Thermal Power Station Chennai Completed
26 Hanil Era Textiles Ltd Mumbai Completed
27 Sanghi Spinners Sanghi Nagar Completed
28 Eastern Spg. Mills Ltd Calcutta Completed
29 BHEL-Hyderabad RIL-Jamnagar Completed
30 BHEL-Hyderabad KMCL- Neelachal Completed
31 BHEL-Hyderabad IOCL-Panipat Completed
32 Karthiga Enterprises Chennai Completed
33 Hyundai Motor India Ltd Sriperumbudur Completed
CUSTOMER LIST FOR CO2 FIRE EXTINGUISHING SYSTEM
Page : 1 of 2
Sl. No. Name of the Customer Place STATUS
CUSTOMER LIST FOR CO2 FIRE EXTINGUISHING SYSTEM
34 Hanil Era Textiles Ltd Mumbai Completed
35 Onshore Construction Co., Pvt. Ltd Mumbai Completed
36 Firepro Systems Pvt. Ltd. Bangalore Completed
37 Firepro Systems Pvt. Ltd. Bangalore Completed
38 TD Power Systems Pvt. Ltd Bangalore Completed
39 Indian Petrochemicals Corporation Ltd Gujarat Completed
40 Reliance Industries Ltd. Hazira Completed
41 Reliance Industries Ltd. Patalganga Completed
42 Vatech Hydro Bhopal Completed
43 Hyundai Motor India Ltd Sriperumbudur Completed
44 Visaka Industries Ltd. Nagpur Completed
45 Visaka Industries Ltd. Nagpur Completed
46 Tyco (Alert Safety Equipments) Banglore Completed
47 Hyundai Motor India Ltd Sriperumbudur Completed
48 Fire Fighters Engg. Chennai Completed
49 Fire Fighters Engg. Chennai Completed
50 Hyundai Motor India Ltd Sriperumbudur Completed
51 Paras Fire Protection Chennai Completed
52 Chentech Enterprises Chennai Completed
53 Visaka Industries Ltd. Nagpur Completed
54 Intek Security Systems (P) Ltd Bangalore Completed
55 Tyco (Alert Safety Equipments) Bangalore Completed
56 Hyundai Motor India Ltd Sriperumbudur Completed
57 GMR Energy Limited Mangalore Completed
58 Indian Oil Corporation Ltd., Mathura Refinery, Mathura (U.P) Mathura Completed
59 Essar Steel Limited Hazira Completed
60 Dekars Techno Engineering Hyderabad Completed
61 Reliance Industries Ltd. Hazira Completed
62 Alert Fire Services Bangalore Completed
63 Reliance Industries Ltd. Hazira Completed
64 M/s. Indian Oil Corporation Limited., Panipat Refinery, Panipat Completed
65 Tyco (Alert Safety Equipments) Bangalore Completed
66 Reliance Industries Ltd. Patalganga Completed
Page : 2 of 2