DIN 3015-1 Light Range DIN 3015-2 Heavy Range DIN … to DIN 3015 DIN 3015-1 Light Range DIN 3015-2...

E 8.

183.

4/04

.17

1

Clamps to DIN 3015 DIN 3015-1 Light Range DIN 3015-2 Heavy Range DIN 3015-3 Twin Clamps

GeneralClamps to DIN 3015 are a sophisticated modular system for fixing pipes with static and dynamic loads.It offers several advantages:

zDamping of shocks, vibrations and noise, as well as compensation of pipe tolerances through the use of elastomer inserts zHigh strength ensured by ribbed clamp bodies zWeld plate from a single pulled piece zSteel parts with sufficient surface protection zSecure overhead installation through clamping effect of the plastic parts zCan be installed on C mounting rails, also available with weld struts zEfficient plug/screw installation of the mounting rail nuts zOptional:

– Elimination of rust penetration due to all-round anti-corrosion coatings

– Gentle component mounting with clamp bodies made of a thermoplastic element

AssemblyAll the pipe clamps in the HY-ROS range offer extremely impressive features: excellent resilience, optimal material resistance to tensile and tear stress, and high abrasion resistance.

The type of pipe clamp, size and material are selected depending on the application and type of stress (thermal / mechanical).

zFor secure mounting, stable carrier units, such as base plates and mounting rails, are required according to the load requirements. zThe first clamp should be mounted directly after the threaded connection. This protects the connection from vibrations. zBends in the pipe should be clamped on both sides of the bend (pulsation direction must be taken into account). zThe prescribed material property limits must be observed. z In the absence of any past experience, the recommended distance between pipe supports must be adhered to (see right). z If valves are incorporated in the pipelines, it is recommended that support is provided in front of and behind these valves.

Recommended distance between pipe supports

Distance between pipe supports L

Pipe diameter D

[m] min [mm] max [mm]

1.0 6.0 12.7

1.2 12.7 22.0

1.5 22.0 32.0

2.0 32.0 38.0

2.7 38.0 57.0

3.0 57.0 75.0

3.5 75.0 76.1

3.7 76.1 88.9

4.0 88.9 102.0

4.5 102.0 114.0

5.0 114.0 168.0

6.0 168.0 219.0

6.7 219.0 324.0

7.0 324.0 356.0

E 8.

183.

4/04

.17

2

Material properties of clamps to DIN 3015Material Density Yield stress and/or

tensile strengthShore hardness Temperature

resistanceFire protection

ISO 1183 ISO 527-2 ISO 868 EN 45545-2Polypropylene (PP)

0.9 g/cm³ 26 MPa - -30 to +90 °C -

Polyamide (PA)

1.13 g/cm³ tr. 90 / lf. 45 Mpa - -40 to +120 °C -

Polyamide, flame-retardant (PAFF)

1.14 g/cm³ tr. 80 / lf. 40 Mpa - -40 to +120 °C R22, R23 / HL1, HL3, HL3

Thermoplastic elastomer (TPE)

0.97 g/cm³ 8.3 Mpa 73 ±5° Shore A Others on request

-40 to +125 °C -

Acrylonitrile butadiene elastomer (NBR)

1.35 g/cm³ 25 Mpa 73 ±5° Shore A Others on request

-35 to +90 °C -

Bolt torque rating to DIN 3015 Part 10Standard Thread Nominal size Torque rating [Nm] with clamp material

PP PA ALLight range M 6 0 to 6 8 10 12Heavy range

M 101 to 2 12 20 303 15 25 35

M 12 4 30 40 55M 16 5 45 55 120M 20 6 80 150 220M 24 7 110 200 250

M 308 180 350 5009 200 370 50010 270 470 600

Twin clamps M 6 1 5 6 -

M 82 to 4 12 12 -5 8 8 -

Note: The specified bolt torque ratings relate to assembly with cover plates and hex. head bolts to ISO 4014 / 4017.

E 8.

183.

4/04

.17

3

Packing details for light range DIN 3015 Part 1Light range Pairs of clamp jaws Weld and cover plates Bolts

Box (pairs) Bag (pairs) Box (pieces) Bag (pieces) Box (pieces) Bag (pieces)PP, PA AL AP DP

0 1000 - 50 250 500 50 1000 501 1000 500 50 250 500 50 1000 502 1000 250 50 250 250 50 1000 503 500 250 50 250 250 50 1000 504 500 200 25 200 200 25 1000 505 250 100 25 100 200 25 500 506 250 100 25 100 200 25 500 50

TMV 6 / TM6 1000 50Washer - 50Stacking bolt the same as normal bolts

Packing details for heavy range DIN 3015 Part 2Heavy range Pairs of clamp jaws Weld and cover plates Bolts

Box (pairs) Bag (pairs) Box (pieces) Bag (pieces) Box (pieces) Bag (pieces)PP, PA AL

1 500 250 25 100 25 250 502 250 150 25 100 25 250 503 250 100 25 100 25 250 504 250 (pieces) - - 50 - 100 -5 120 (pieces) - - 25 - 25 -

TM 10 250 50TM 12 250 50Washer - 50Stacking nut size 1 - 4 250 50Stacking nut size 5 100 -Stud size 1 - 3 250 50Stud size 4 250 -Stud size 5 100 -

Packing details for twin clamps DIN 3015 Part 3Twin clamp Pairs of clamp jaws Weld and cover plates Bolts

Box (pairs) Bag (pairs) Box (pieces) Bag (pieces) Box (pieces) Bag (pieces)PP, PA AP DP

1 1000 50 200 250 50 500 502 750 50 100 200 50 500 503 500 50 100 200 50 500 504 250 25 100 100 25 200 255 250 25 100 100 25 200 25

TMV 6 / TM6 50TM 8 25Stacking bolt the same as normal boltsNote: Only available in given pack sizes

E 8.

183.

4/04

.17

4

Pipe outside Ø

Inches Nominal bore

[mm] 6 - - 6.4 1/4 - 8 5/16 - 9.5 3/8 -

10 - G 1/812 - -12.7 1/2 -13.7 - G 3/414 - -15 - -16 5/8 -17.1 - G 3/818 - -19 3/4 -

20 - -21.3 - G 1/222 - -23 - -25 - -25.4 1 -26.9 - G 3/428 - -

Pipe outside Ø

Inches Nominal bore

[mm]30 - -32 1 1/4 -33.7 - G 135 - -38 1 1/2 G 1 1/8

40 - -42 - G 1 1/444.5 1 3/4 -48.3 - G 1 1/2

50.8 2 -54 - -57 2 1/4 -

60.3 - G 263.5 2 1/2 -65 - -

70 - -73 - -76.1 3 G 2 1/2

Pipe outside Ø

Inches Nominal bore

[mm] 80 - - 88.9 3 1/2 G 3

90 - - 96 - -

101.6 4 G 3 1/2108 4 1/4 -114.3 4 1/2 G 4136 - -139.7 5 1/2 G 5168 6 1/2 G 6177.8 7 -193.7 7 5/8 G 7

219.1 8 5/8 G 8244.5 - -273 - G 10

323.9 12 3/4 G 12355.6 - G 14

406.4 - G 16

Metric / imperial conversion table

E 8.

183.

4/04

.17

5

Light Range to DIN 3015 Part 1

HRL, HRGL

Size Pipe outside Ø[mm]

0

6.4 8 9.5 10 12

1

6 6.4 8 9.5 10 12

2

12.7 13.7 14 15 16 17.1 18

3

19 20 21.3 22 23 25 25.4

4 26.9 28 30

5

32 33.7 35 38 40 42

6 44.5 48.3 50.8

7

57.2 60.3 63.5 70.0 73.0 76.1

8 88.9101.6

HRL 2 A 16 PP ST M BL

Designation HRL = HY-ROS clamp, light range with ribbed internal surface HRGL = HY-ROS clamp, light range with smooth internal surface Size 0 = size 0 1 = size 1 2 = size 2 up to size 8 Model for complete clamps (pair of clamp jaws not mentioned) A = with weld plate, cover plate and hex. head bolt AV = with extended weld plate, cover plate and hex. head bolt A1 = with cover plate and hex. head bolt A1TM = with cover plate, hex. head bolt and mounting rail nut B = with weld plate, hex. socket cap bolt and washer BV = with extended weld plate, hex. socket cap bolt and washer B1 = with hex. socket cap bolt and washer B1TM = with hex. socket cap bolt, washer and mounting rail nut C = with weld plate, slotted-head bolt and washer CV = with extended weld plate, slotted-head bolt and washer C1 = with slotted-head bolt and washer C1TM = with slotted-head bolt, washer and mounting rail nut D = with stacking bolt and safety plate Pipe diameter Material of clamp jaws PP = polypropylene PA = polyamide PAFF = polyamide, flame-retardant to EN 45545-2 R22, R23, HL3 TPE = thermoplastic elastomer AL = aluminium (sizes 0, 7, 8 on request) Material of steel parts ST = steel A2 = stainless steel (on request) A4 = stainless steel (on request) Thread type M = metric thread

Plating of steel parts BL = weld plate unplated, cover plate zinc-plated, bolts zinc-plated ZN = weld plate zinc-plated, cover plate zinc-plated, bolts zinc-plated Others on request

Model code (also order example)

E 8.

183.

4/04

.17

6

Models for light range DIN 3015 Part 1Model A Size 0 - 8

Model AV Size 0 - 8

Model A1 Size 0 - 8

Model A1TM Size 0 - 8

Model B Size 0 - 8

Model BV Size 0 - 8

Model B1 Size 0 - 8

Model B1TM Size 0 - 8

Model C Size 0 - 6

Model CV Size 0 - 6

Model C1 Size 0 - 6

Model C1TM Size 0 - 6

Model D Size 0 - 6

Note: No washers are required in the AL version for series B and C.

E 8.

183.

4/04

.17

7

Dimensions for light range DIN 3015 Part 1Size 0 Size 1-8

Size Dimensions [mm] Hex. head Hex. socket

Stud Slotted head

a1 a2 a3 a4 a5 h1 h2 ISO 4014 ISO 4762 DIN 938 ISO 12070 - 30 28 44 58 16 32 M6 x 30 M6 x 20 M6 x 20 M6 x 201 20 36 36 50 64 16 32 M6 x 30 M6 x 20 M6 x 20 M6 x 202 26 42 40 56 70 19.5 39 M6 x 35 M6 x 25 M6 x 25 M6 x 253 33 50 48 64 78 20.5 41 M6 x 40 M6 x 30 M6 x 30 M6 x 304 40 60 57 73 87 24 48 M6 x 45 M6 x 35 M6 x 35 M6 x 355 52 72 70 86 100 32 64 M6 x 60 M6 x 50 M6 x 50 M6 x 506 66 88 86 100 116 36 72 M6 x 70 M6 x 60 M6 x 60 M6 x 607 94 122 121 136 150 51.5 103 M6 x 100 M6 x 85 - -8 120 148 147 162 178 64 128 M6 x 125 M6 x 110 - -

NOTE: For sizes 7 and 8, the cover plate and weld plate are 5 mm thick.

E 8.

183.

4/04

.17

8

Individual parts for light range DIN 3015 Part 1

Pair of clamp jaws, ribbed (HRL...KP...)

Cover plate (DP)

Weld plate (AP)

Pair of clamp jaws, smooth (HRL...KP...)

Extended weld plate (APV)

Size 0

Size 0

Size 0

Size 0

Size 0

Size 1 - 8

Size 1 - 8

Size 1 - 8

Size 1 - 8

Size 1 - 8

HRL 3 KP 23 PP

HRL 3 DP ST ZN

HRL 2 AP ST M BL

Range HRL = HY-ROS clamp, light range with ribbed internal surface HRGL = HY-ROS clamp, light range with smooth internal surface Size (as per dimensions) Designation KP = pair of clamp jaws Pipe diameter Material of clamp jaws PP = polypropylene PA = polyamide PAFF = polyamide, flame-retardant to EN 45545-2 R22, R23, HL3 TPE = thermoplastic elastomer AL = aluminium (sizes 0, 7, 8 on request)

Range HRL = HY-ROS light range Size (as per dimensions) Designation DP = cover plate Material of steel parts ST = steel A2 = stainless steel (on request) A4 = stainless steel (on request) Plating of steel parts BL = unplated Others on request

Range HRL = HY-ROS light range Size (as per dimensions) Designation AP = weld plate APV = extended weld plate Material of steel parts ST = steel A2 = stainless steel (on request) A4 = stainless steel (on request) Thread type M = metric thread Plating of steel parts BL = unplated Others on request




E 8.

183.

4/04

.17

9

Interconnecting weld plate (RAP)

Double weld plate (DAP)

Dimensions

HRL 2a RAP ST M BL

HRL 2a DAP ST M BL

Range HRL = HY-ROS light range Size (as per dimensions) Designation RAP = interconnecting weld plate Material of steel parts ST = steel A2 = stainless steel (on request) A4 = stainless steel (on request) Thread type M = metric thread Plating of steel parts BL = unplated Others on request

Range HRL = HY-ROS light range Size (as per dimensions) Designation DAP = double weld plate Material of steel parts ST = steel A2 = stainless steel (on request) A4 = stainless steel (on request) Thread type M = metric thread Plating of steel parts BL = unplated Others on request



3 mm thick

Size Number of clamps

Dimensions [mm]e1 e2 e3 e4 L

0 10 - 30 - - 2981b 10 17 40 20 7 3942a 10 20 43 26 7 4272b 10 20 52 26 7 5083a 10 24 52 33 7.5 5163b 10 24 75 33 7.5 7234 5 28.5 60 40 8.5 2975 5 35 75 52 9 3706 5 43 90 66 10 446


Dimensions [mm]e1 e2 e3 e4 L

0 2 - - 30 9.5 631b 2 18 40 20 8 752a 2 21.5 43 26 8.5 862b 2 21 52 26 8 943a 2 26 52 33 9.5 1043b 2 25 75 33 8.5 1254 2 28.5 60 40 8.5 1175 2 35 75 52 9 1456 2 43 90 66 10 176

Dimensions

3 mm thick

E 8.

183.

4/04

.17

10

Bolts6kt-shr.ISO4014 - M6 x 30 - 8.8 A3B

Range 6kt-shr.ISO4014 = hex. head bolt to ISO 4014 Zyl-shr.ISO4762 = hex. socket cap bolt to ISO 4762 Zyl-shr.ISO1207 = slotted-head bolt to ISO 1207 Size ISO4014 ISO4762 ISO1207 for HRL sizeM6 x 30 M6 x 20 M6 x 20 0+1M6 x 35 M6 x 25 M6 x 25 2M6 x 40 M6 x 30 M6 x 30 3M6 x 45 M6 x 35 M6 x 35 4M6 x 60 M6 x 50 M6 x 50 5M6 x 70 M6 x 60 M6 x 60 6M6 x 100 M6 x 85 - 7M6 x 125 M6 x 110 - 8

Bolt quality 8.8 = to ISO 4014, ISO 4762 4.6 = to ISO 1207 Bolt plating A3B = zinc-plated Others on request


Hex. head bolt ISO 4014

Hex. socket cap bolt ISO 4762

Slotted-head bolt ISO 1207

Stacking bolt (AF)

Dimensions

HRL 4 AF ST M ZN

Range HRL = HY-ROS light range Size (as per dimensions) Designation AF = stacking bolt Material of steel parts ST = steel A2 = stainless steel (on request) A4 = stainless steel (on request) Thread type M = metric thread Plating of steel parts ZN = zinc-plated Others on request


Size Dimensions [mm]L1 L2 L3

0+1 34 14 M62 39 14 M63 44 14 M64 49 14 M65 64 14 M66 74 14 M6

NOTE: Size 7 + 8 on request

Safety plate (SIP)

Dimensions (for all sizes)

HRL 0 SIP ST ZN

Range HRL = HY-ROS light range Size 0 = for all sizes Designation SIP = safety plate Material of steel parts ST = steel A2 = stainless steel (on request) A4 = stainless steel (on request) Plating of steel parts ZN = zinc-plated Others on request


E 8.

183.

4/04

.17

11

C mounting rail (TS)

Mounting rail nut (TM)

Dimensions

C mounting rail TS

C mounting rail with weld strutsTS28x11AS

C mounting rail TSavailable in 1 m and 2 m pieces

Dimensions

HRL TS28x11 ST BL 1m

HRL TMV6 ST ZN

Range HRL = HY-ROS light range Model TS28x11 = C mounting rail 28x11 TS28x14 = C mounting rail 28x14 TS28x30 = C mounting rail 28x30 TS28x11AS = C mounting rail with weld struts 28x11

Material of steel parts ST = steel AL = aluminium (on request) A2 = stainless steel (on request) A4 = stainless steel (on request) Plating of steel parts BL = unplated ZN = zinc-plated Others on request Length 1 m 2 m (not for C mounting rail with weld struts) Other lengths on request

Range HRL = HY-ROS light range Designation TMV6 = mounting rail nut with anti-twist protection, size M6 (standard) TM6 = mounting rail nut without anti-twist protection, size M6 Material of steel parts ST = steel A4 = stainless steel (on request) Plating of steel parts ZN = zinc-plated Others on request



C mounting rail with weld strutsavailable in 1 m pieces

4.5

10.6

1510

.6

25.4

M6

E 8.

183.

4/04

.17

12

HYDAC Accessories GmbH Hirschbachstr. 2 66280 Sulzbach/Saar Tel.: +49 (0)6897 - 509-01 Fax: +49 (0)6897 - 509-1009 Internet: www.hydac.com E-mail: [email protected]

NOTEThe information in this brochure relates to the operating conditions and applications described. For applications and operating conditions not described, please contact the relevant technical department. Users bear the responsibility in all cases for determining the product’s suitability in the specific application. Figures given for product characteristics are average values for a new product which are subject to an ageing process. Subject to technical modifications and errors.

E 8.

183.

4/04

.17

13

Light Range with Elastomer Insertto DIN 3015 Part 1HREL, HRERL

HREL 4 A 16 PP ST M BL

Designation HREL = HY-ROS clamp, light range, elastomer insert with smooth internal surface HRERL = HY-ROS clamp, light range, elastomer insert with ribbed internal surface Size 4 = size 4 6 = size 6 Model for complete clamps (pair of clamp jaws not mentioned) A = with elastomer insert, weld plate, cover plate and hex. head bolt Pipe diameter Material of clamp jaws PP = polypropylene PA = polyamide PAFF = polyamide, flame-retardant to EN 45545-2 R22, R23, HL3 Material of steel parts ST = steel A2 = stainless steel (on request) A4 = stainless steel (on request) Thread type M = metric thread

Plating of steel parts BL = weld plate unplated, cover plate zinc-plated, bolts zinc-plated Others on request


Model A Size 4, 6

Size d internal surface smooth

d internal surface ribbed

[mm] [mm]

4

6 - 8 - 10 10 12 12 12.7 - 14 14 15 15 16 16 17.2 17.2 18 - 19 -

6

20 20 21.3 - 22 22 23 - 25 25 26.9 - 28 28 30 30 32 -

E 8.

183.

4/04

.17

14

Dimensions

Individual parts

Size Dimensions [mm] Hex. head

Hex. socket

Stud Slotted head

d1 d2 a1 a2 a3 h1 h2 ISO 4014 ISO 4762 DIN 938 ISO 1207

4 25.5 31 40 59 57 23.5 47 M6 x 45 M6 x 35 M6 x 35 M6 x 35

6 39 46 66 88 86 35.5 71 M6 x 70 M6 x 60 M6 x 60 M6 x 60

Pair of clamp jaws (KP) Size 4, 6

Elastomer insert smooth (HRES…EE…) Size 2/4L, 3/6L

Elastomer insert ribbed (HRERS…EE...) Size 2/4L, 3/6L

HREL 4 KP PP

HRES 2/4L EE 16 TPE

Range HREL = HY-ROS clamp, light range, with elastomer insert Size 4 = size 4 6 = size 6 Designation KP = pair of clamp jaws Material of clamp jaws PP = polypropylene PA = polyamide PAFF = polyamide, flame-retardant to EN 45545-2 R22, R23, HL3

Range HRES = elastomer insert, internal surface smooth HRERS = elastomer insert, internal surface ribbed Size 2/4L = size 2 (HRS), size 4 (HRL) 3/6L = size 3 (HRS), size 6 (HRL) Designation EE = elastomer insert Pipe diameter (as per dimensions) Insert material TPE = thermoplastic elastomer



E 8.

183.

4/04

.17

15

Heavy Range to DIN 3015 Part 2

HRS, HRGS

Size Pipe outside Ø [mm]

1

6 13.7 6.4 14 8 15 9.5 16 10 17.1 12 18 12.7

2

19 25.4 20 26.9 21.3 28 22 30 25

3

25 35 30 38 32 40 33.7 42

4

30 55 38 57 42 60.3 44.5 63.5 48.3 65 50.8 70

5

38 76.1 65 80 70 88.9 73

6

65 114.3 96 127101.6108

7

90136139.7168

8

168177.8193.7219.1

9

219.1244.5273323.9

10355.6406.4

HRS 2 S 30 PP ST M BL

Designation HRS = HY-ROS clamp, heavy range with ribbed internal surface HRGS = HY-ROS clamp, heavy range with smooth internal surface (on request) Size 1 = size 1 2 = size 2 3 = size 3 up to size 10 Model for complete clamps (pair of clamp jaws not mentioned) S = with weld plate, cover plate and hex. head bolt SV = with extended weld plate, cover plate and hex. head bolt S1 = with cover plate and hex. head bolt S1TM = with cover plate, hex. head bolt and mounting rail nut (only up to size 4) I = with weld plate, hex. socket cap bolt and washer (only up to size 7) material of clamp jaws AL A = with stacking bolt and safety plate (only up to size 7) D = with double weld plate, double cover plate and hex. head bolt Pipe diameter Material of clamp jaws PP = polypropylene PA = polyamide PAFF = polyamide, flame-retardant to EN 45545-2 R22, R23, HL3 TPE = thermoplastic elastomer AL = aluminium Material of steel parts ST = steel A2 = stainless steel (on request) A4 = stainless steel (on request) Thread type M = metric thread

Plating of steel parts BL = weld plate unplated, cover plate zinc-plated, bolts unplated (from size 8 cover plate unplated) BL/ZN = weld plate unplated, cover plate zinc-plated, bolts zinc-plated ZN = weld plate zinc-plated, cover plate zinc-plated, bolts zinc-plated


E 8.

183.

4/04

.17

16

Models for heavy range DIN 3015 Part 2Model S Size 1 - 10

Model SV Size 1 - 10

Model S1 Size 1 - 10

Model S1TM Size 1 - 4

Model I Size 1 - 7

Note: No washers are required in the AL version for series I.

Model A Size 1 - 7

Model D Size 1 - 10

E 8.

183.

4/04

.17

17

Dimensions for heavy range DIN 3015 Part 2

Size Dimensions [mm] Hex. head Hex. socket

a1 a2 a3 a3 a4 a5 b1 b2 h1 h2 s1 s2 ISO 4014 ISO 4762PA, PP AL

1 33 73 55 57 85 113 30 60 24 48 8 11 M10 x 45 M10 x 252 45 85 70 70 97 125 30 60 32 64 8 11 M10 x 60 M10 x 403 60 100 85 85 112 140 30 60 38 76 8 11 M10 x 70 M10 x 504 90.5 140 115 119 160 190 45 90 54.5 109 10 14 M12 x 100 M12 x 805 122 180 152 160 205 240 60 120 70 140 10 18 M16 x 130 M16 x 1106 168 225 205 215 270 310 80 160 100 200 15 22 M20 x 190 M20 x 1507 205 270 252 258 320 370 90 180 115 230 15 26 M24 x 220 M24 x 1808 265 340 320 323 - - 120 240 160 320 25 - M30 x 300 -9 395 520 466 475 - - 160 324 235 470 30 - M30 x 450 -10 530 680 630 630 - - 180 364 295 590 30 - M30 x 560 -

E 8.

183.

4/04

.17

18

Individual parts for heavy range DIN 3015 Part 2

Pair of clamp jaws, ribbed (HRS...KP...)

Cover plate (DP)

Double cover plate (DDP)

Safety plate (SIP)

Weld plate (AP)

Pair of clamp jaws, smooth (HRGS...KP...)

Extended weld plate (APV)

Double weld plate (DAP)

Size 1 - 10

Size 1 - 10

Size 1 - 10

Size 1 - 10

Size 1 - 10

Size 1 - 7

Size 1 - 10

Size 1 - 10

HRS 3 KP 23 PP

HRS 2 DP ST BL

HRS 2 AVP ST M BL

Range HRS = HY-ROS clamp, heavy range with ribbed internal surface HRGS = HY-ROS clamp, heavy range with smooth internal surface Size (as per dimensions) Designation KP = pair of clamp jaws Pipe diameter Material of clamp jaws PP = polypropylene PA = polyamide PAFF = polyamide, flame-retardant to EN 45545-2 R22, R23, HL3 TPE = thermoplastic elastomer AL = aluminium (not for HRGS)

Range HRS = HY-ROS heavy range Size (as per dimensions) Designation DP = cover plate DDP = double cover plate SIP = safety plate (only up to size 7) Material of steel parts ST = steel A2 = stainless steel (on request) A4 = stainless steel (on request) Plating of steel parts BL = unplated ZN = zinc-plated (only up to size 7)

Range HRS = HY-ROS heavy range Size (as per dimensions) Designation AP = weld plate APV = extended weld plate DAP = double weld plate Material of steel parts ST = steel A2 = stainless steel (on request) A4 = stainless steel (on request) Thread type M = metric thread Plating of steel parts BL = unplated ZN = zinc-plated




E 8.

183.

4/04

.17

19

Bolts

Stacking bolt (AF)

Dimensions

6kt-shr.ISO4014 - M10 x 70 - 8.8 A3B

HRS 5 AF16 ST M ZN

Range 6kt-shr.ISO4014 = hex. head bolt to ISO 4014 Zyl-shr.ISO4762 = hex. socket cap bolt to ISO 4762

Size ISO4014 ISO4762* for HRS sizeM10 x 45 M10 x 25 1M10 x 60 M10 x 40 2M10 x 70 M10 x 50 3M12 x 100 M12 x 80 4M16 x 130 M16 x 110 5M20 x 190 M20 x 150 6M24 x 220 M24 x 180 7M30 x 300 8M30 x 450 9M30 x 560 10 * only AL version

Bolt quality 8.8 = to ISO 4014, ISO 4762 Bolt plating no details = unplated A3B = zinc-plated

Range HRS = HY-ROS heavy range Size (as per dimensions) Designation AF10 = stacking bolt M10 AF12 = stacking bolt M12 AF16 = stacking bolt M16 AF20 = stacking bolt M20 AF24 = stacking bolt M24 Material of steel parts ST = steel A2 = stainless steel (on request) A4 = stainless steel (on request) Thread type M = metric thread Plating of steel parts BL = unplated ZN = zinc-plated



Hex. head bolt ISO 4014 HRS size 1 -10

Hex. socket cap bolt ISO 4762 HRS size 1 -7

Size Dimensions [mm]L1 L2 d

1 50 25 M102 65 25 M103 75 25 M104 106 26 M125* 145 35 M166* 200 50 M207* 236 56 M24* without washer

E 8.

183.

4/04

.17

20



Dimensions

Dimensions

HRS TS40x22 ST BL 2m

HRS TM10 ST M ZN

Range HRS = HY-ROS heavy range Model TS40x22 = C mounting rail 40x22

Material of steel parts ST = steel A2 = stainless steel (on request) A4 = stainless steel (on request) Plating of steel parts BL = unplated ZN = zinc-plated Length 1 m 2 m Other lengths on request

Range HRS = HY-ROS heavy range Designation TM10 = mounting rail nut size M10 TM12 = mounting rail nut size M12 Material of steel parts ST = steel A2 = stainless steel (on request) A4 = stainless steel (on request) Thread type M = metric thread Plating of steel parts ZN = zinc-plated Others on request



Note:available in 1 m and 2 m pieces

Mounting rail nut TM10

Mounting rail nut TM12

E 8.

183.

4/04

.17

21

Heavy Range with Elastomer Insertto DIN 3015 Part 2HRES, HRERS

Size d internal surface smooth

d internal surface ribbed

[mm] [mm]

2

6 -8 -

10 1012 1212,7 -14 1415 1516 1617,2 17,218 -19 -

3

20 2021,3 -22 2223 -25 2526,9 -28 2830 3032 -

4

33,7 -35 -38 3840 -42 4245,5 44,548 4851 -53,4 -56,4 57

5

60 -65 -70 -73 -76 76

6

83 -89 8994 -

101 -

7

108 108114 -133 -140 -

HRES 2 S 16 PP ST M BL

Designation HRES = HY-ROS clamp, heavy range, elastomer insert with smooth internal surface HRERS = HY-ROS clamp, heavy range, elastomer insert with ribbed internal surface Size 2 = size 2 3 = size 3 4 = size 4 5 = size 5 6 = size 6 7 = size 7 Model for complete clamps (pair of clamp jaws not mentioned) S = with elastomer insert, weld plate, cover plate and hex. head bolt Pipe diameter Material of clamp jaws PP = polypropylene PA = polyamide PAFF = polyamide, flame-retardant to EN 45545-2 R22, R23, HL3 Material of steel parts ST = steel A2 = stainless steel (on request) A4 = stainless steel (on request) Thread type M = metric thread

Plating of steel parts BL = weld plate unplated, cover plate zinc-plated, bolts unplated BL/ZN = weld plate unplated, cover plate zinc-plated, bolts zinc-plated ZN = weld plate zinc-plated, cover plate zinc-plated, bolts zinc-plated


E 8.

183.

4/04

.17

22

Dimensions

Individual parts

Size Dimensions [mm] Hex. headd1 d2 b1 h1 h2 a1 a2 a3 s1 ISO 4014

2 25.5 31 30 31 62 45 85 70 8 M10 x 603 39 46 30 37 74 60 100 85 8 M10 x 704 65 74 45 53.5 107 90.5 140 115 10 M12 x 1005 89 98 60 68.5 137 122 180 152 10 M16 x 1306 116 132 80 98.5 197 168 225 205 15 M20 x 1907 154 168 90 113.5 227 205 270 252 15 M24 x 220

Pair of clamp jaws (KP) Size 2 - 7

Model S Size 2 - 7

Elastomer insert smooth (HRES…EE…) Size 2/4L, 3/6L, 4, 5, 6, 7

Elastomer insert ribbed (HRERS…EE...) Size 2/4L, 3/6L, 4, 5, 6, 7

HRES 4 KP PP

HRES 2/4L EE 16 TPE

Range HRES = HY-ROS clamp, heavy range, with elastomer insert

Size 2 = size 2 3 = size 3 4 = size 4 5 = size 5 6 = size 6 7 = size 7 Designation KP = pair of clamp jaws Material of clamp jaws PP = polypropylene PA = polyamide PAFF = polyamide, flame-retardant to EN 45545-2 R22, R23, HL3

Range HRES = elastomer insert, internal surface smooth HRERS = elastomer insert, internal surface ribbed

Size 2/4L = size 2 (HRS), size 4 (HRL) 3/6L = size 3 (HRS), size 6 (HRL) 4 = size 4 5 = size 5 6 = size 6 7 = size 7 Designation EE = elastomer insert Pipe diameter (as per dimensions) Insert material TPE = thermoplastic elastomer NBR* = acrylonitrile butadiene elastomer * only sizes 5 -7



E 8.

183.

4/04

.17

23

Dimensions

Twin Clamps to DIN 3015 Part 3

HRZ, HRGZ

Size Pipe outside Ø [mm]

1

6 6.4 8 9.51012

2

12.713.714151617.118

3

192021.322232525.4

426.92830

5

3233.735384042

HRZ 2 A 16-16 PP ST M BL

Designation HRZ = HY-ROS twin clamp with ribbed internal surface HRGZ = HY-ROS twin clamp with smooth internal surface Size 1 = size 1 2 = size 2 up to size 5 Model for complete clamps (pair of clamp jaws not mentioned) A = with weld plate, cover plate and hex. head bolt A1 = with cover plate and hex. head bolt A1TM = with cover plate, hex. head bolt and mounting rail nut D = with stacking bolt and safety plate Pipe diameter (specification of each Ø as per pipe outside Ø) Material of clamp jaws PP = polypropylene PA = polyamide PAFF = polyamide, flame-retardant to EN 45545-2 R22, R23, HL3 TPE = thermoplastic elastomer Material of steel parts ST = steel A2 = stainless steel (on request) A4 = stainless steel (on request) Thread type M = metric thread

Plating of steel parts BL = weld plate unplated, cover plate zinc-plated, bolts zinc-plated (only model A) ZN = weld plate zinc-plated, cover plate zinc-plated, bolts zinc-plated


E 8.

183.

4/04

.17

24

Models for twin clamps to DIN 3015 Part 3Model A Size 1 - 5

Model A1 Size 1 - 5

Model A1TM Size 1 - 5

Model D Size 1 - 5

Dimensions

Size Dimensions [mm] Hex. head bolta1 a2 a3 a6 h1 h2 h3 ISO 4014

1 20 37 36 34 18.5 27 43 M6 x 352 29 55 53 51 18 26 43.5 M8 x 353 36 70 67 64 23.5 37 54.5 M8 x 454 45 85 82 78 26 42 59.5 M8 x 505 56 110 106 102 32 54 71.5 M8 x 60

E 8.

183.

4/04

.17

25

Individual parts for twin clamps DIN 3015 Part 3

Pair of clamp jaws, ribbed (HRZ...KP...)

Weld plate (AP)

Pair of clamp jaws, smooth (HRGZ...KP...)

Size 1 - 5

Size 1 - 5

Size 1 - 5

HRZ 3 KP 23-23 PP

Range HRZ = HY-ROS twin clamp with ribbed internal surface HRGZ = HY-ROS twin clamp with smooth internal surface Size 1 = size 1 2 = size 2 up to size 5 Designation KP = pair of clamp jaws Pipe diameter (specification of each Ø as per pipe outside Ø) Material of clamp jaws PP = polypropylene PA = polyamide PAFF = polyamide, flame-retardant to EN 45545-2 R22, R23, HL3 TPE = thermoplastic elastomer Others on request


Cover plate (DP)Size 1 - 5 HRZ 3 DP ST BL

HRZ 2 AP ST M BL

Range HRZ = HY-ROS twin clamp Size (as per dimensions) Designation DP = cover plate Material of steel parts ST = steel A2 = stainless steel (on request) A4 = stainless steel (on request) Plating of steel parts BL = unplated Others on request

Range HRZ = HY-ROS twin clamp Size (as per dimensions) Designation AP = weld plate Material of steel parts ST = steel A2 = stainless steel (on request) A4 = stainless steel (on request) Thread type M = metric thread Plating of steel parts BL = unplated Others on request



E 8.

183.

4/04

.17

26

Interconnecting weld plate (RAP)*

Safety plate (SIP)

Dimensions

Dimensions

*not to DIN 3015

Size 1

Size 2 - 5

HRZ 2 RAP ST M BL

HRZ 2-5 SIP ST ZN

Range HRZ = HY-ROS twin clamp Size (as per dimensions) Designation RAP = interconnecting weld plate Material of steel parts ST = steel A2 = stainless steel (on request) A4 = stainless steel (on request) Thread type M = metric thread Plating of steel parts BL = unplated Others on request

Range HRZ = HY-ROS twin clamp Size 1 = size 1 2-5 = size 2-5 Designation SIP = safety plate Material of steel parts ST = steel A2 = stainless steel (on request) A4 = stainless steel (on request) Plating of steel parts ZN = zinc-plated Others on request




Dimensions [mm]L1 L2 L d

1 5 18 40 196 M62 5 28 58 288 M83 5 35 72 358 M84 5 43 90 446 M85 5 55 112 558 M8

5 mm thick

E 8.

183.

4/04

.17

27



Dimensions

Dimensions

HRL TS28x11 ST BL 1m

HRL TMV6 ST ZN

Range HRL = HY-ROS light range Model TS28x11 = C mounting rail 28x11 TS28x14 = C mounting rail 28x14 TS28x30 = C mounting rail 28x30 TS28x11AS = C mounting rail with weld struts 28x11 Material of steel parts ST = steel AL = aluminium (on request) A2 = stainless steel (on request) A4 = stainless steel (on request) Plating of steel parts BL = unplated ZN = zinc-plated Others on request Length 1 m 2 m (not for C mounting rail with weld struts) Other lengths on request

Range HRL = HY-ROS light range, for size 1 HRZ = HY-ROS twin clamp, from size 2 Designation TMV6 = mounting rail nut with anti-twist protection, M6 (only size 1) TM6 = mounting rail nut without anti-twist protection, M6 (only size 1) TM8 = mounting rail nut M8 (from size 2) Material of steel parts ST = steel A4 = stainless steel (on request) Plating of steel parts ZN = zinc-plated Others on request



C mounting rail TSavailable in 1 m and 2 m pieces

C mounting rail with weld strutsavailable in 1 m pieces

Size 1 (TMV6) Size 2 - 5 (TM8)

C mounting rail TS

C mounting rail with weld strutsTS28x11AS

4.5

10.6

1510

.6

25.4

M6

O-ring

E 8.

183.

4/04

.17

28

HYDAC Accessories GmbH Hirschbachstr. 2 66280 Sulzbach/Saar Tel.: +49 (0)6897 - 509-01 Fax: +49 (0)6897 - 509-1009 Internet: www.hydac.com E-mail: [email protected]

NOTEThe information in this brochure relates to the operating conditions and applications described. For applications and operating conditions not described, please contact the relevant technical department. Users bear the responsibility in all cases for determining the product’s suitability in the specific application. Figures given for product characteristics are average values for a new product which are subject to an ageing process. Subject to technical modifications and errors.

Bolts

Stacking bolt (AF)

Dimensions

6kt-shr.ISO4014 - M6 x 35 - 8.8 A3B

HRZ 4 AF ST M ZN

Range 6kt-shr.ISO4014 = hex. head bolt to ISO 4014

Size ISO4014 for HRZ sizeM6 x 35 1M8 x 35 2M8 x 45 3M8 x 50 4M8 x 60 5

Bolt quality 8.8 = to ISO 4014 Bolt plating no details = unplated A3B = zinc-plated

Range HRL = HY-ROS light range, for size 1 HRZ = HY-ROS twin clamp, from size 2 Size

for HRZ size0+1 12 2up to size 5

Designation AF = stacking bolt Material of steel parts ST = steel A2 = stainless steel (on request) A4 = stainless steel (on request) Thread type M = metric thread Plating of steel parts ZN = zinc-plated Others on request



Hex. head bolt ISO 4014 HRZ size 1 - 5

Size Dimensions [mm]L1 L2 d

1 34 14 M62 33 13 M83 44 15 M84 49 15 M85 62 15 M8

HRZ size 1 - 5

DIN 3015-1 Light Range DIN 3015-2 Heavy Range DIN … to DIN 3015 DIN 3015-1 Light Range DIN 3015-2...

Documents

Transcript of DIN 3015-1 Light Range DIN 3015-2 Heavy Range DIN … to DIN 3015 DIN 3015-1 Light Range DIN 3015-2...