Digital Super Hybrid System KX-TD1232G Installation Manual

Digital Super Hybrid System

MODEL KX-TD1232G

Installation Manual

Please read this manual before connecting the KX-TD1232G.

Description

Digital Super Hybrid System (Main Unit)

Digital Super Hybrid System (Main Unit)

Digital proprietary telephone with display

Digital proprietary telephone with large display

Digital proprietary telephone with monitor

Digital DSS Console

8-Station Line Unit

2-ISDN S0 Line Unit

4-ISDN S0 Line Card

2-ISDN S0 Line Card

System Inter Connection Cards (2 Cards and 1 Cable)

2400bps Remote Card

Thank you for purchasing the Panasonic Model KX-TD816SL/KX-TD1232SL, Digital Super Hybrid System.

System Components

Model

KX-TD816SL

KX-TD1232SL

KX-T7230SL

KX-T7235SL

KX-T7250SL

KX-T7240SL

KX-TD170SL

KX-TD280SL

KX-TD281G*1

KX-TD282G*2

KX-TD192G*1

KX-TD196G*1

Service Unit

Proprietary Telephone(PT)

Optional Equipment

System Components Table

• In this Installation Manual, the suffix “SL” or “G” of each model number isomitted.

• The Proprietary Telephone is abbreviated as “PT.”

The models marked *1 can be installed in KX-TD1232 only.

The models marked *2 can be installed in KX-TD816 only.

2

• Keep the unit away from heating appliances and electrical noise generating devicessuch as fluorescent lamps, motors and television. These noise sources can interferewith the performance of the Digital Super Hybrid System.

• This unit should be kept free of dust, moisture, high temperature (more than 40˚C /104˚F) and vibration, and should not be exposed to direct sunlight.

• Never attempt to insert wires, pins, etc. into the vents or other holes of this unit.

• If there is any trouble, disconnect the unit from the telephone line. Plug the telephonedirectly into the telephone line. If the telephone operates properly, do not reconnectthe unit to the line until the trouble has been repaired. If the telephone does not operateproperly, chances are that the trouble is in the telephone system, and not in the unit.

• Do not use benzine, thinner, or the like, or any abrasive powder to clean the cabinet.Wipe it with a soft cloth.

• This unit may only be installed and serviced by Qualified Service Personnel.

Attention

WARNING

• THIS UNIT IS EQUIPPED WITH AN EARTHING CONTACT PLUG. FOR SAFETYREASONS THIS PLUG MUST ONLY BE CONNECTED TO AN EARTHINGCONTACT SOCKET WHICH HAS BEEN INSTALLED ACCORDING TOREGULATIONS.

• THE POWER SOCKET WALL OUTLET SHOULD BE LOCATED NEAR THISEQUIPMENT AND BE EASILY ACCESSIBLE.

• TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT TORAIN OR ANY TYPE OF MOISTURE.

The serial number of this product may be found on the label affixed to the bottomof the unit. You should note the serial number of this unit in the space providedand retain this book as a permanent record of your purchase to aid in identificationin the event of theft.

MODEL NO.:

SERIAL NO.:

3

For your future referenceDATA OF PURCHASE

NAME OF DEALER

DEALER’S ADDRESS

Introduction

This Installation Manual provides technical information for the Panasonic DigitalSuper Hybrid System, KX-TD816/KX-TD1232. It is designed to serve as an overalltechnical reference for the system and includes a description of the system, itshardware and software, features and services and environmental requirements.

This manual contains the following sections:

Section 1, System Outline.Provides general information on the system including system capacity andspecifications.

Section 2, Installation.Contains the basic system installation and wiring instructions, as well as how toinstall the optional cards and units.

Section 3, Features.Describes all the basic, optional and programmable features in alphabetical order. Italso provides information about the programming required, conditions, connectionreferences, related features and operation for every feature.

Section 4, System Programming.Provides step-by-step programming instructions for a proprietary telephone.

Section 5, List.Lists tone/ring tone and default values of system programming.

Section 6, TroubleshootingProvides information for system and telephone troubleshooting.

NOTEThe following document may be used in conjunction with this manual:

• User Manual for KX-TD816/KX-TD1232 System, Proprietary Telephones, DSSConsole and Single Line Telephones

4

*1 : Available for KX-TD1232 only. 5*2 : Available for KX-TD816 only.

Contents

Section 1, System Outline1.1 System Highlights ............................................................................. 1-21.2 Basic System Construction............................................................... 1-41.3 Proprietary Telephones / Proprietary Single Line Telephone ...... 1-51.4 Options ............................................................................................... 1-6

1.4.1 Station Line Unit (KX-TD170) ............................................... 1-61.4.2 CO Line / ISDN S0 Line Card (KX-TD181 / KX-TD182)*1.. 1-61.4.3 CO Line / ISDN S0 Line Card (KX-TD281/KX-TD282)*2.... 1-61.4.4 CO Line / ISDN S0 Line Unit

(KX-TD180, KX-TD280, KX-TD283)................................... 1-61.4.5 System Inter Connection Cards (KX-TD192)*1...................... 1-71.4.6 Remote Card (KX-TD196)*1................................................... 1-71.4.7 DSS Console (KX-T7240 / KX-T7040).................................. 1-8

1.5 Specifications ..................................................................................... 1-91.5.1 General Description................................................................. 1-91.5.2 Characteristics ......................................................................... 1-101.5.3 System Capacity...................................................................... 1-11

Section 2, Installation2.1 Before Installation............................................................................. 2-22.2 Installation of the Main Unit............................................................ 2-4

2.2.1 Unpacking ............................................................................... 2-42.2.2 Name and Location ................................................................. 2-42.2.3 Wall Mounting......................................................................... 2-62.2.4 Frame Ground Connection ...................................................... 2-72.2.5 Opening Front Cover............................................................... 2-8

2.3 Connection......................................................................................... 2-92.3.1 System Connection Diagram................................................... 2-92.3.2 Extension Connection

for Proprietary Telephones, Single Line Telephones and DSS Consoles.. 2-112.3.3 Optional Extension Connection of Clip Terminal*1................. 2-162.3.4 Paralleled Telephone Connection

for Proprietary Telephone and a Single Line Telephone ............................ 2-182.3.5 EXtra Device Port (XDP) Connection

for a Digital Proprietary Telephone and a Single Line Telephone ............. 2-202.3.6 Polarity Sensitive Telephone Connection ............................... 2-212.3.7 Doorphone and Door Opener Connection............................... 2-222.3.8 External Relay, External Ringer and

External Sensor Connection .................................................... 2-242.3.9 External Pager (Paging Equipment) Connection .................... 2-262.3.10 External Music Source Connection......................................... 2-272.3.11 Printer Connection .................................................................. 2-28

6 *:Available for KX-TD1232 only.

Contents

2.4 Optional Cards and Units Installation............................................ 2-322.4.1 Location of Optional Cards and Units..................................... 2-322.4.2 CO Line Connection (Optional Card) ..................................... 2-342.4.3 Lightning Protector Installation .............................................. 2-362.4.4 CO Line Connection (Optional Unit)...................................... 2-392.4.5 Extension Connection ............................................................. 2-392.4.6 Installing Expansion Unit

(KX-TD170 / KX-TD180 / KX-TD280 / KX-TD283) ........... 2-402.4.7 Remote Card Installation*........................................................ 2-442.4.8 System Connection*................................................................. 2-45

2.5 Power Failure Transfer Connection................................................ 2-472.6 Starting the System for the First Time ........................................... 2-482.7 System Restart................................................................................... 2-492.8 System Data Clear............................................................................. 2-50

Section 3, FeaturesA Absent Message Capability ................................................................ 3-2

Account Code Entry ........................................................................... 3-2Alternate Calling – Ring / Voice......................................................... 3-4Alert Indication................................................................................... 3-4Answering, Direct CO Line................................................................ 3-5Automatic Adjustment Time .............................................................. 3-5Automatic Callback Busy (Camp-On) ............................................... 3-6Automatic Error Logging ................................................................... 3-6Automatic Overflow and Hurry-Up Transfer ..................................... 3-7Automatic Redial → Redial, Automatic............................................. 3-99Automatic Station Release.................................................................. 3-8

B Background Music (BGM) ................................................................. 3-8Background Music (BGM) – External ............................................... 3-9Budget Management........................................................................... 3-10Busy Lamp Field ................................................................................ 3-10Busy Station Signaling (BSS) ............................................................ 3-11Button, Direct Station Selection (DSS) ............................................. 3-11Button, Flexible .................................................................................. 3-12Button, Group-CO (G-CO)................................................................. 3-13Button, Loop-CO (L-CO) ................................................................... 3-14Button, Single-CO (S-CO) ................................................................. 3-15Buttons on Proprietary Telephones..................................................... 3-16

C CALL FORWARDING FEATURES – SUMMARY ......................... 3-18Call Forwarding – All Calls................................................................ 3-18Call Forwarding – Busy...................................................................... 3-19Call Forwarding – Busy / No Answer ................................................ 3-20

7

Contents

Call Forwarding – Follow Me ............................................................ 3-21Call Forwarding – No Answer............................................................ 3-21Call Forwarding – to CO Line............................................................ 3-22Call Hold – CO Line........................................................................... 3-23Call Hold – Intercom .......................................................................... 3-23Call Hold, Exclusive – CO Line......................................................... 3-24Call Hold, Exclusive – Intercom ........................................................ 3-24Call Hold Retrieve – CO Line ............................................................ 3-25Call Hold Retrieve – Intercom............................................................ 3-25Call Log, Incoming............................................................................. 3-26Call Park ............................................................................................. 3-27Call Pickup, CO Line ......................................................................... 3-28Call Pickup, Directed.......................................................................... 3-28Call Pickup, Group ............................................................................. 3-28Call Pickup Deny................................................................................ 3-29Call Splitting....................................................................................... 3-29CALL TRANSFER FEATURES – SUMMARY ............................... 3-30Call Transfer, Screened – to CO Line................................................. 3-30Call Transfer, Screened – to Extension .............................................. 3-31Call Transfer, Unscreened – to Extension .......................................... 3-31Call Waiting ........................................................................................ 3-32Call ID ................................................................................................ 3-33Calling Line Identification Restriction (CLIR) .................................. 3-34Calling Party Control (CPC) Signal Detection................................... 3-34Charge Fee Reference......................................................................... 3-35Class of Service (COS)....................................................................... 3-36CO Line Connection Assignment....................................................... 3-37CO Line Connection Assignment – Outgoing.................................... 3-37CO Line Group .................................................................................. 3-38CO Line Name Display ...................................................................... 3-39Conference.......................................................................................... 3-39Conference, Unattended ..................................................................... 3-40Confirmation Tone.............................................................................. 3-40Connected Line Identification Restriction (COLR) ........................... 3-42

D Data Line Security .............................................................................. 3-43Delayed Ringing → Ringing, Delayed............................................... 3-101Department Codes .............................................................................. 3-43Dial Tone, Distinctive......................................................................... 3-44Dial Type Selection ............................................................................ 3-45Direct Dialing In (DDI) ...................................................................... 3-46Direct In Lines (DIL).......................................................................... 3-46Direct Station Selection (DSS) Button → Button, Direct Station

Selection (DSS) ....................................................................... 3-11

8

Contents

Directed Call Pickup → Call Pickup, Directed .................................. 3-28Display, Call Information ................................................................... 3-47Display, Self-Extension Number ........................................................ 3-48Display, Time and Date ...................................................................... 3-49Display Contrast Adjustment.............................................................. 3-49Do Not Disturb (DND)....................................................................... 3-50Do Not Disturb for Direct Dialing In Call.......................................... 3-51Do Not Disturb (DND) Override........................................................ 3-51Door Opener ....................................................................................... 3-52Doorphone Call................................................................................... 3-52DSS Console (KX-T7240 / KX-T7040)............................................. 3-53

E Electronic Station Lockout ................................................................. 3-56Emergency Call .................................................................................. 3-56End-to-End DTMF Signaling (Tone Through)................................... 3-57Executive Busy Override – CO Line.................................................. 3-57Executive Busy Override – Extension................................................ 3-58Extension Connection Assignment..................................................... 3-59Extension Group................................................................................. 3-59External Feature Access ..................................................................... 3-60External Relay .................................................................................... 3-60External Ringer................................................................................... 3-61External Sensor................................................................................... 3-62EXtra Device Port (XDP) ................................................................... 3-63

F Flash.................................................................................................... 3-63Flexible Button → Button, Flexible ................................................... 3-12Flexible Numbering............................................................................ 3-64Floating Station .................................................................................. 3-67Full One-Touch Dialing...................................................................... 3-68

G Group Call Pickup → Call Pickup, Group.......................................... 3-28Group CO (G-CO) Button → Button, Group-CO (G-CO)................. 3-13

H Handset / Headset Selection................................................................ 3-68Handsfree Answerback ....................................................................... 3-69Handsfree Operation........................................................................... 3-69Hold Recall ......................................................................................... 3-70Host PBX Access................................................................................ 3-70HOTEL APPLICATION .................................................................... 3-71

Check - In / Check - Out..................................................................................... 3-71

Timed Reminder, Remote (Wake-Up Call) ........................................................ 3-72

Hurry-Up Transfer → Automatic Overflow and Hurry-Up Transfer . 3-7I Incoming Call Log → Call Log, Incoming......................................... 3-26

Intercept Routing ................................................................................ 3-73Intercom Calling ................................................................................. 3-73

9

Contents

L Last Number Redial → Redial, Last Number..................................... 3-100LED Indication, CO Line ................................................................... 3-74LED Indication, Intercom................................................................... 3-75Line Access, Automatic...................................................................... 3-76Line Access, CO Line Group ............................................................ 3-77Line Access, Direct............................................................................. 3-77Line Access, Individual ...................................................................... 3-78Line Preference – Incoming (No Line / Prime Line / Ringing Line) . 3-79Line Preference – Outgoing (Idle Line / No Line / Prime Line) ........ 3-80Lockout............................................................................................... 3-81Log-In / Log-Out ................................................................................ 3-81Loop-CO (L-CO) Button → Button, Loop-CO (L-CO)..................... 3-14

M Manager Extension ............................................................................. 3-82 Message Waiting................................................................................. 3-82Microphone Mute ............................................................................... 3-83Mixed Station Capacities.................................................................... 3-84Module Expansion.............................................................................. 3-84Music on Hold .................................................................................... 3-85

N Night Service ...................................................................................... 3-86Notebook Function ............................................................................. 3-87

O Off-Hook Monitor............................................................................... 3-87One-Touch Dialing.............................................................................. 3-88One-Touch Transfer by DSS Button................................................... 3-89Operator .............................................................................................. 3-89Operator Call ...................................................................................... 3-90

P PAGING FEATURES – SUMMARY................................................. 3-91Paging – All ........................................................................................ 3-91Paging – External................................................................................ 3-92Paging – Group................................................................................... 3-93Paralleled Telephone........................................................................... 3-93Pause Insertion, Automatic................................................................. 3-94Pickup Dialing .................................................................................... 3-95Power Failure Restart ......................................................................... 3-96Power Failure Transfer ....................................................................... 3-96Predial ................................................................................................ 3-97Privacy, Automatic ............................................................................. 3-97Private Call ......................................................................................... 3-98Pulse to Tone Conversion ................................................................... 3-98

R Redial, Automatic .............................................................................. 3-99Redial, Last Number .......................................................................... 3-100Redial, Saved Number ....................................................................... 3-100Remote Station Lock Control ............................................................. 3-101

10 * : Available for KX-TD1232 only.

Contents

Ringing, Delayed ................................................................................ 3-101Ringing, Discriminating ..................................................................... 3-102Ringing Tone Selection for CO Buttons............................................. 3-102

S Saved Number Redial → Redial, Saved Number............................... 3-100Screened Call Transfer – to CO Line

→ Call Transfer, Screened – to CO Line ................................ 3-30Screened Call Transfer – to Extension

→ Call Transfer, Screened – to Extension .............................. 3-31Secret Dialing ..................................................................................... 3-103Single-CO (S-CO) Button → Button, Single-CO (S-CO) ................. 3-15Special Features for KX-T7235.......................................................... 3-104

Call Log, Outgoing ....................................................................................... 3-104

Extension Dialing ......................................................................................... 3-104

Station Speed Dialing ................................................................................... 3-105

System Feature Access Menu....................................................................... 3-105

System Speed Dialing................................................................................... 3-106

Station Feature Clear .......................................................................... 3-107Station Hunting................................................................................... 3-108Station Message Detail Recording (SMDR) ..................................... 3-108Station Programming.......................................................................... 3-111Station Programming Data Default Set .............................................. 3-112Station Speed Dialing ......................................................................... 3-112System Connection* ............................................................................ 3-113System Data Default Set..................................................................... 3-114System Programming and Diagnosis with Personal Computer.......... 3-115System Programming with Proprietary Telephone............................. 3-116System Speed Dialing......................................................................... 3-117

T Terminate ............................................................................................ 3-117Time-Out, Variable ............................................................................. 3-118Timed Reminder ................................................................................. 3-120Toll Restriction ................................................................................... 3-120Toll Restriction Override by Account Code Entry ............................. 3-127Toll Restriction Override for System Speed Dialing.......................... 3-128Trunk (CO Line) Answer From Any Station (TAFAS) ..................... 3-128

U Unattended Conference → Conference, Unattended.......................... 3-40Uniform Call Distribution (UCD)....................................................... 3-129Unscreened Call Transfer – to Extension

→ Call Transfer, Unscreened – to Extension .......................... 3-31V Voice Mail Integration ........................................................................ 3-131

Volume Control – Speaker / Ringer.................................................... 3-137

* : Available for KX-TD1232 only. 11

Contents

Section 4, System Programming4.1 General Programming Instructions ................................................ 4-2

4.1.1 Using the Proprietary Telephone............................................. 4-34.1.2 Programming Ways ................................................................. 4-74.1.3 Entering Characters ................................................................. 4-94.1.4 Example of Programming ....................................................... 4-12

4.2 Manager Programming .................................................................... 4-14[000] Date and Time Set ................................................................... 4-14[001] System Speed Dialing Number Set ......................................... 4-16[002] System Speed Dialing Name Set............................................. 4-18[003] Extension Number Set............................................................. 4-19[004] Extension Name Set ................................................................ 4-21[005] Flexible CO Button Assignment ............................................. 4-23[006] Operator / Manager Extension Assignment – Day / Night ..... 4-25[007] DSS Console Port and Paired Telephone Assignment ........... 4-26[008] Absent Messages ..................................................................... 4-28[009] Emergency Dial Number Set................................................... 4-29[010] Budget Management ............................................................... 4-30[011] Charge Margin Rate ................................................................ 4-31

4.3 System Programming ....................................................................... 4-32[100] Flexible Numbering ................................................................ 4-32[102] Day / Night Service Starting Time .......................................... 4-35[103] Automatic Access CO Line Group Assignment ..................... 4-37[105] Account Codes ........................................................................ 4-38[106] Station Hunting Type .............................................................. 4-39[107] System Password..................................................................... 4-40[108] One-Touch Transfer by DSS Button ....................................... 4-41[109] Expansion Card / Unit Type .................................................... 4-42[113] VM Status DTMF Set ............................................................. 4-43[114] VM Command DTMF Set ...................................................... 4-45[115] Adjust Time*............................................................................ 4-47[116] ROM Version Display ............................................................. 4-48[117] Charge Display Selection ........................................................ 4-49[118] Charge Verification Assignment ............................................. 4-50[119] Charge Verification ID Code Set............................................. 4-51[120] Operator Queue ....................................................................... 4-52[121] Pulse Dial Reception Assignment ........................................... 4-53[122] Automatic Door Open Assignment ......................................... 4-54[123] Hotel Application .................................................................... 4-55

12

Contents

4.4 Timer Programming ......................................................................... 4-56[200] Hold Recall Time .................................................................... 4-56[201] Transfer Recall Time............................................................... 4-57[202] Call Forwarding – No Answer Time....................................... 4-58[203] Intercept Time ......................................................................... 4-59[204] Pickup Dial Waiting Time ....................................................... 4-60[207] First Digit Time ....................................................................... 4-61[208] Inter Digit Time....................................................................... 4-62[209] Automatic Redial Repeat Times.............................................. 4-63[210] Automatic Redial Interval Time.............................................. 4-64[211] Dial Start Time ........................................................................ 4-65[212] Call Duration Count Start Time .............................................. 4-66[213] External Relay Connecting Time ............................................ 4-67[214] Message Waiting Ring Interval Time...................................... 4-68[215] Ring-Off Detection Time ........................................................ 4-69

4.5 TRS Programming............................................................................ 4-70[301]–[305] TRS Denied Code Entry for Levels 2 through 6........... 4-70[306]–[310] TRS Excepted Code Entry for Levels 2 through 6........ 4-71

4.6 CO Line Programming..................................................................... 4-72[400] CO Line Connection Assignment ........................................... 4-72[401] CO Line Group Assignment.................................................... 4-73[402] Dial Mode Selection................................................................ 4-74[404] DTMF Time ............................................................................ 4-75[405] CPC Signal Detection Incoming Set ....................................... 4-76[407]–[408] DIL 1:1 Extension — Day / Night ................................ 4-77[409]–[410] Intercept Extension — Day / Night............................... 4-78[411] Host PBX Access Codes ......................................................... 4-79[412] Pause Time .............................................................................. 4-81[413] Flash Time............................................................................... 4-82[414] Disconnect Time...................................................................... 4-83[415] CPC Signal Detection Outgoing Set ....................................... 4-84[417] Tone Detection ........................................................................ 4-86[418] External Ringer Assignment ................................................... 4-87[419] Subscriber Number Assignment.............................................. 4-88[420] Direct Dialing In...................................................................... 4-89[421] CO Line Name Assignment .................................................... 4-90

4.7 COS Programming ........................................................................... 4-91[500]–[501] Toll Restriction Level — Day / Night ........................... 4-91[503] Call Transfer to CO Line......................................................... 4-92[504] Call Forwarding to CO Line ................................................... 4-93[505] Executive Busy Override ........................................................ 4-94

* : Available for KX-TD1232 only. 13

Contents

[506] Executive Busy Override Deny............................................... 4-95[507] Do Not Disturb Override......................................................... 4-96[508] Account Code Entry Mode...................................................... 4-97[509]-[510] Toll Restriction Level for System Speed Dialing

–Day / Night .................................................................. 4-98[511] Door Opener Access................................................................ 4-99[512] External Relay Access............................................................. 4-100[513] Night Service Access .............................................................. 4-101[514] Do Not Disturb for Direct Dialing In Call .............................. 4-102[516] Calling Line Identification Restriction.................................... 4-103[517] Connected Line Identification Restriction .............................. 4-104

4.8 Extension Programming................................................................... 4-105[600] EXtra Device Port ................................................................... 4-105[601] Class of Service....................................................................... 4-106[602] Extension Group Assignment ................................................. 4-108[603]–[604] DIL 1:N Extension and Delayed Ringing

— Day / Night ......................................................................... 4-109[605]–[606] Outgoing Permitted CO Line Assignment

— Day / Night ......................................................................... 4-111[607]–[608] Doorphone Ringing Assignment — Day / Night .......... 4-113[609] Voice Mail Access Codes ........................................................ 4-114[610] Department Codes ................................................................... 4-115[611] Extension Connection Assignment ......................................... 4-117[612] Data Line Security................................................................... 4-118

4.9 Resource Programming.................................................................... 4-119[800] SMDR Incoming / Outgoing Call Log Printout ...................... 4-119[801] SMDR Format ......................................................................... 4-120[802] System Data Printout............................................................... 4-121[803] Music Source Use.................................................................... 4-122[804] External Pager BGM ............................................................... 4-123[805] External Pager Confirmation Tone.......................................... 4-124[806]–[807] Serial Interface (RS-232C) Parameters

— Port 1 / Port 2 ..................................................................... 4-125[813] Floating Number Assignment ................................................. 4-127[814] Modem Standard* .................................................................... 4-129

4.10 Option Programming........................................................................ 4-130[990] System Additional Information............................................... 4-130[991] COS Additional Information................................................... 4-135[992] CO Line Group Additional Information.................................. 4-137

Contents

Section 5, List5.1 Tone / Ring Tone................................................................................ 5-25.2 Default Values.................................................................................... 5-4

Section 6, Trouble shooting6.1 Trouble shooting................................................................................ 6-2

6.1.1 Installation ............................................................................... 6-26.1.2 Connection............................................................................... 6-36.1.3 Operation ................................................................................. 6-46.1.4 Using Rest Button.................................................................... 6-5

14

Section 1System Outline

This section provides general information on the system,including system capacity and specifications.

1-2 System Outline *: Available for KX-TD1232 only.

1.1 System Highlights

System CapacityBasic Module System

System Expansion ConnectionKX-TD816 ISDN S0 line 0 4 —

Extension 8 16 —KX-TD1232 ISDN S0 line 0 6 12

Extension 16 32 64

Module Expansion Expansion modules are used to increase the system capacity.Extension modules and ISDN modules can be added to the basicsystem to add extensions and ISDN lines.

EXtra Device Port (XDP) Each extension jack in the system supports the connection of aproprietary telephone/DSS Console and a single line device. Thedevices have different extension numbers and are treated as twocompletely different extensions.

Paralleled Telephone ConnectionEvery jack in the system also supports the parallel connection of aproprietary telephone and a single line device. They share the sameextension number and are considered by the system to be oneextension.

Super Hybrid System This system supports the connection of proprietary telephones, DSSConsoles and single line devices such as single line telephones,facsimiles, and data terminals.

System Connection*

With the addition of optional System Inter Connection Card, twoDigital Super Hybrid Systems can be connected together to expandthe system capacity. The two systems function as one, however,some functions such as paging and music on hold are duplicated.

Proprietary Telephones (PT) The system supports three different models of proprietarytelephones.

Programming System The system can be programmed from a proprietary telephone orfrom a personal computer.

System Outline 1-3

1.1 System Highlights

Trunk (CO Line) Answer From Any Station (TAFAS) Ringing occurs over the external paging system; call can beanswered from any station.

Charge Fee Reference Allows the user to see charges and to print out the charges.

Budget Management Limits the telephone usage to a pre-assigned amount.

Hotel ApplicationAllows to handle the front and operator services such as check-in/check-out and wake-up call setting.

Uniform Call Distribution (UCD)Allows an incoming calls to be distributed uniformly to a specificgroup of extensions.

1-4 System Outline

1.2 Basic System Construction

The KX-TD816 has a basic capacity of eight extensions, and theKX-TD1232 has a basic capacity of 16 extensions. It is capable ofsupporting Panasonic proprietary telephones, DSS Consoles andsingle line devices such as single line telephones, facsimiles. To expand its capabilities the system can be equipped with optionalcomponents or customer-supplied peripherals such as externalspeakers and external music sources (e.g., radios).

D1232DIGITAL SUPER HYBRID SYSTEM

PanasonicPanasonic


KX-TD816 KX-TD1232

System Outline 1-5

1.3 Proprietary Telephones/ProprietarySingle Line Telephone

The following Panasonic proprietary telephones (PT) are availablewith this system.

Proprietary DescriptionTelephoneKX-T7230 Digital, display, speakerphone, 24 CO

KX-T7235 Digital, large display, speakerphone, 12 CO

KX-T7250 Digital, monitor, 6 CO

Note: CO: CO line access button

1-6 System Outline *1 : Available for KX-TD1232 only.*2 : Available for KX-TD816 only.

1.4 Options

8 or 16 extensions can be added.

Each unit adds eight extensions. One unit for KX-TD816 andup to two units for KX-TD1232 can be installed per system.

1.4.1 Station Line Unit (KX-TD170)

4 ISDN S0 lines can be added.

The following card can be installed per system.

KX-TD281: Adds four ISDN S0 lines. (Basic Rate Interface)

1.4.2 ISDN S0 Line Card (KX-TD281)*1


Panasonic


The following card can be installed.

KX-TD282: Adds two ISDN S0 lines. (Basic Rate Interface)

1.4.3 ISDN S0 Line Card (KX-TD282)*2

Panasonic


8 extensions can be added.

* : Available for KX-TD1232 only. System Outline 1-7

1.4 Options

The Remote Card allows programming and maintenance of thesystem from a remote location. (Baud Rate: 300 / 1200 / 2400 bps)

1.4.6 Remote Card (KX-TD196)*


The following unit can be installed per system.

KX-TD280: Adds two ISDN S0 lines. (Basic Rate Interface)

1.4.4 ISDN S0 Line Unit (KX-TD280)

Permits two KX-TD1232 to be connected together — todouble system capacity.

Connection Cable

1.4.5 System Inter Connection Cards (KX-TD192)*


Panasonic


PanasonicPanasonic


PanasonicPanasonic


Panasonic

Telephone Line

Personal Computerwith Modem

Note: The KX-TD1232 is illustrated as a main unit.

CentralOffice

1-8 System Outline

1.4 Options

Paired Telephone(ProprietaryTelephone)

DSS ConsoleKX-T7240

Pair

Permits easy and quick access to stations and features. The BusyLamp Field (BLF) shows the idle, busy or Do Not Disturb state ofeach station. If the Operator uses a DSS Console as well as aproprietary telephone, the BLF will show the check-in/check-outstatus. DSS Consoles are designed for use with a proprietarytelephone. The KX-TD816 supports up four DSS Consoles. TheKX-TD1232 supports up to eight DSS Consoles per system.

1.4.7 DSS Console (KX-T7240)

Panasonic

DIGITAL


Panasonic

DIGITALPanasonic


System Outline 1-9

1.5 Specifications

1.5.1 General Description

System Capacity KX-TD816 — ISDN S0 lines 4 max.Stations 16 max. (32 max. with XDP)

KX-TD1232 — ISDN S0 lines 6 max.Stations 32 max. (64 max. with XDP)

Control Method Stored Program CPU: 16 bits CPUControl ROM: 1 MB, Control RAM: 256KB

Switching Non Blocking PCM Time Switch

Power Supplies Primary Power 230 VAC, 50 HzSecondary Station Supply Volt: 30V

Circuit Volt: ± 5V, ± 15V

Dialing Internal Dial Pulse (DP) 10 pps

Tone (DTMF) Dialing

Connector ISDN S0 lines 4-pin Connector Stations Amphenol ConnectorPaging Output Pin Jack (RCA JACK)External Music Input Two-conductors Jack

(MINIJACK 3.5 mm/9/64 inch diameter)

SMDR (Station Message Detail Recording) Interface V. 24 (RS-232C)Output Equipment PrinterDetail Recording Date, Time, Extension Number,

Department Code, CO Line Number,Dialed Number, Call Duration,Charge Fee, Account Code

Extension Connection Cable

Single line telephones

KX-T7230, KX-T7235, KX-T7240, KX-T7250

1 pair wire (T, R)

1 pair wire (D1, D2): T and R are not necessary.or 2 pair wire (T, R, D1, D2)

1-10 System Outline

1.5 Specifications

1.5.2 Characteristics

Station Loop Limit KX-T7230 / KX-T7235 / KX-T7250.......40 ohmsSingle Line Telephone .............................600 ohms including setDoorphone................................................20 ohms

Minimum Leakage Resistance 15 000 ohms

Maximum Number of Station Instruments per Line1 for KX-T7230, KX-T7235, KX-T7250 or singleline telephone2 by Parallel or eXtra Device Port Connection of aproprietary telephone and a single line telephone

Ring Voltage 65 Vrms at 32 Hz depends on Ringing Load

Primary Power 230 VAC, 50 Hz

Central Office Loop Limit 1 600 ohms max.

Environmental Requirements 0 – 40 °C / 32 – 104 °F, 10 – 90%

System Outline 1-11

1.5 Specifications

1.5.3 System Capacity

Lines, Cards, Station EquipmentKX-TD1232

KX-TD816 Max. QuantityMax. Quantity Single System

Item System Connection

System Inter Connection Card — — 2

Service Unit 1 1 2

ISDN S0 Line Card 1 1 2

ISDN S0 Line Unit 1 1 2

ISDN S0 Line 4 6 12 (Baud Rate Interface)

Station Line Unit 1 2 4

Extension Jack 16 32 64

Station Terminal 32 64 128(including DSS Consoles)

DSS Console 4 8 16

Remote Card — 1 1

Doorphone 1 1 2

Door Opener 2 2 4

External Music Source 2 2 4

External Pager 2 2 4

External Relay 1 1 2

External Ringer 1 1 2

External Sensor 1 1 2

System DataItem Max. Quantity

Operator 2

System Speed Dialing 500

One-Touch Dialing 24 per station (proprietary telephone)

Station Speed Dialing 10 per station

1-12 System Outline

1.5 Specifications

Call Park 10

Absent Message 9

CO Line Group 8

Toll Restriction Level 8

Extension Group 8

Class of Service 8

Message Waiting 128

Uniform Call Distribution Group 8

Section 2Installation

This section contains the basic system installation and wiringinstructions, as well as how to install the optional cards and

units.

2-2 Installation

2.1 Before Installation

Please read the following notes concerning installation andconnection before installing the system.

Safety Installation InstructionsWhen installing telephone wiring, basic safety precautions shouldalways be followed to reduce the risk of fire, electric shock andinjury to persons, including the following:1. Never install telephone wiring during a lightning storm.2. Never install telephone jacks in wet locations unless the jack is

specifically designed for wet locations.3. Never touch uninsulated telephone wires or terminals unless the

telephone line has been disconnected at the network interface.4. Use caution when installing or modifying telephone lines.

Installation PrecautionsThis set is exclusively made for wall mounting only. Avoidinstalling in the following places. (Doing so may result inmalfunction, noise, or discoloration.)1. In direct sunlight and hot, cold, or humid places. (Temperature

range: 0°C – 40°C / 32°F – 104°F)2. Sulfuric gases produced in areas where there are thermal springs,

etc. may damage the equipment or contacts.3. Places in which shocks or vibrations are frequent or strong.4. Dusty places, or places where water or oil may come into

contact with the unit.5. Near high-frequency generating devices such as sewing

machines or electric welders.6. On or near computers, telexes, or other office equipment, as well

as microwave ovens or air conditioners. (It is preferable not toinstall in the same room with the above equipment.)

7. Install at least 1.8 m (6 feet) from radios and televisions. (boththe main unit and proprietary telephones)

8. Do not obstruct area around the main unit (for reasons ofmaintenance and inspection — be especially careful to allowspace for cooling above and at the sides of the main unit).

Wiring PrecautionsMake sure to keep the following instructions when wiring.1. Do not wire the telephone cable in parallel with an AC power

source, computer, telex, etc. If the cables are run near thosewires, shield the cables with metal tubing or use shielded cablesand ground the shields.

Installation 2-3

2.1 Before Installation

2. If cables are run on the floor, use protectors or the like to protectthe wires where they may be stepped on. Avoid wiring undercarpets.

3. Avoid using the same power supply outlet for computers,telexes, and other office equipment. Otherwise, the systemoperation may be interrupted by the induction noise from suchequipment.

4. Please use one pair telephone wire for extension connection of(telephone) equipment such as single line telephones, dataterminals, answering machines, computers, voice processingsystems, etc., except proprietary telephones ( KX-T7230, KX-T7235, KX-T7250 etc.).

5. Unplug the system during wiring. After all the wiring arecompleted, plug the system.

6. Mis-wiring may cause the system to operate improperly. Refer to Section 6.1.1 “Installation” and Section 6.1.2“Connection.”

7. If an extension does not operate properly, disconnect thetelephone from the extension line and then connect again, orunplug the system and then plug the system again.

8. The system is equipped with a 3-wire grounding type plug. Thisis a safety feature. If you are unable to insert the plug into theoutlet, contact your electrician to replace your obsolete outlet.Do not defeat the purpose of the grounding-type plug.

9. Use twisted pair cable for CO line connection.10. CO lines should be installed with lightning protectors. For

details, refer to Section 2.4.3 “Lightning Protectors Installation.”

Warning:Static sensitive devices used.To protect printed circuit boardsfrom static electricity, do not touchconnectors indicated on the rightpicture without first dischargingbody static by touching a groundedor wearing a properly installedgrounding strap.

Warning : Static sensitive connectors

2-4 Installation

2.2 Installation of the Main Unit

2.2.2 Name and Location

Overview of the Main Unit

2.2.1 Unpacking

AC Inlet

Ground Terminal

Serial Interface

(RS-232C)Power Indicator


PanasonicAC Inlet

Ground Terminal

Serial Interface

(RS-232C)

Power IndicatorPanasonic


KX-TD816 KX-TD1232Main Unit one oneAC Cord one oneTemplet one oneScrew three fourAnchor Plug three fourPager Connector two twoMusic Source Connector two twoDoorphone, Door Opener Connector five fiveExpansion Line Cord Holder one oneFerrite Core — twoUser Manual one oneReference Manual for Single Line Telephone one oneOverlay for a proprietary telephone one one

KX-TD816 KX-TD1232

Installation 2-5


Inside View of the Main Unit

External Relay JackCentral Ringer JackExternal Sensor JackDoor Opener Jack 1Door Opener Jack 2Doorphone Jack

External Relay Jack

Central Ringer Jack

External Sensor Jack

Door Opener Jack 1

Doorphone Jack

Door Opener Jack 2

Extension Amphenol Connectors

Paging Jack 2Paging Jack 1

External Music Jack 2External Music Jack 1

System Clear SwitchReset Button

KX-TD816

KX-TD1232 Extension Amphenol Connectors

Paging Jack 2

Paging Jack 1

External Music Jack 2

External Music Jack 1

System Clear Switch

Reset Button

2-6 Installation

2.2.3 Wall Mounting

This set is exclusively made for wall mounting only. The wallwhere the main unit is to be mounted must be able to support theweight of the main unit. If screws other than the ones supplied areused, use the same-sized diameter screws as the enclosed ones.

Mounting on Wooden Wall

3. Hook the main unit on the screw heads.

1. Place the templet (included) on the wallto mark the screw positions.

2. Install the screws (included) into the wall.

Mounting on Concrete or MortarWall

6.4mm

29mm

2. Drill holes and drive the anchor plugs(included) with a hammer, flush to thewall.

1. Place the templet (included) on the wallto mark the screw positions.

3. Install the screws (included) into theanchor plugs.

4. Hook the main unit on the screw heads.

Templet

Wooden

Wall

Drive the screw

to this position.

To the wall surface Concret WallAnchor Plug

Drive the screw

to this position.

Templet

KX-TD1232KX-TD816

KX-TD816 KX-TD1232

Installation 2-7



Panasonic

2.2.4 Frame Ground Connection

IMPORTANT!!!Connect the frame of the main unit to ground.

Test Procedure1. Obtain a suitable voltmeter and set it for a possible reading of up

to 250 VAC.

2. Connect the meter probes between the two main AC voltagepoints on the wall outlet. The reading obtained should be 220-240 VAC.

3. Move one of the meter probes to the 3rd prong terminal (GND).Either the same reading or a reading of 0 volt should beobtained.

4. If a reading of 0 volt at one terminal and a reading of 220-240VAC at the other terminal is not obtained, the outlet is notproperly grounded.This condition should be corrected by a qualified electrician (perarticle 250 of the National Electrical Code).

5. If a reading of 0 volt at one terminal and a reading of 220-240VAC at the other terminal is obtained, then set the meter to the“OHMS/RX1” scale, place one probe at the GND Terminal andthe other probe at the terminal which gave a reading of 0 volt.

A reading of less than 1 ohm should be obtained.If the reading is not obtained the outlet is not adequatelygrounded, see qualified electrician.

To ground

To ground

KX-TD816 KX-TD1232

Panasonic


2-8 Installation



Panasonic

A

2.2.5 Opening Front Cover

1. Loosen two screws on the right side of the main unit. 2. Open the front cover in the direction of arrow .A

Note Two screws are attached to the front cover with springs so that they willnot be lost.

Screw

ScrewPanasonic


A

Screw

Screw

KX-TD816 KX-TD1232

Installation 2-9

2.3 Connection

2.3.1 System Connection Diagram


Panasonic

Printer for SMDR or Personal Computer for System Programming

To AC Outlet

Doorphone

Door Opener 1 Door Opener 2

Central Ringer

External Sensor External Relay

Amplifier Speaker 1External Music Source 1

External Music Source 2Speaker 2Amplifier


2-10 Installation

2.3.1 System Connection Diagram

: needs Optional Cards or Units.

• Parallel connection of telephone is possible.Refer to Section 2.3.4 “Paralleled TelephoneConnection.”

• The KX-TD1232 is illustrated as a main unit.

D1232DEGITAL SUPER HYBRID SYSTEM

Panasonic

Panasonic

DIGITAL

Panasonic

DIGITAL

DIGITALPanasonic

Panasonic XXXXXXXXXXXXXXXXXX

Panasonic

Panasonic10CH

CH

MUTE

1

4

7

2

5

8

0

3

6

9

Panasonic

TONE

PROGRAM

AUTO

REDIAL/

PAUSE

ON

OFFTALK

D P E R

T U V

P R S

W X Y

J K L

G H I

A B C

D E F

M N O

XXXXXXX

XXXXXXX

XXXXXXXXXXXX

XX

XX

XX

XX

XX

XX

XX

XX

XX

XX

XX

XX

XX

XXXXXXXXXXX

SOUND CHARGERHOLD

MUTE

PAGE/INTERCOM

XXXXXXXXXXX

CHARGE

VOLUMEMIC

XXXXXXXXXXX

XXXXXXXXXXX

AUTO SCAN

10CH 10CH

Panasonic

(CO Lightning Protectors)

KX-TD816: to CO's 1 through 8

KX-TD1232: to CO's 1 through 12ISDN S0 Lines

KX-TD816: 16 Extensions ( 8 extensions - initial, 8 extensions )KX-TD1232:32 Extensions (16 extensions - initial, 16 extensions )

( one pair)

( one pair)

( onepair)

( one pair)

(onepair)

(two pair)

(two pair)

(two pair)

(two pair)

Single Line Telephone

Data Terminal

Cordless Phone

Telephone AnsweringMachine with Facsimile

Voice Processing System

KX-T7250

KX-T7240

KX-T7230

KX-T7235

It is recommended thatextension of jack 1 is a displayproprietary telephone.

Installation 2-11

2.3.2 Extension Connection for Proprietary Telephones, Single Line Telephones and DSS Consoles

After inserting the connector, fastenthe connector with the nylon tie.

To connect extension jacks, insert the connector(s) to the system asshown.For Cable Pin Numbers to Be Connected, see page 2-13.

1

26

25

50

1

26

To extension (Jack 9 - 16)


Connector type50-pin (Amphenol 57 JEseries or the equivalent)


KX-TD816 KX-TD1232

2-12 Installation


Panasonic

1232G

Panasonic

DIGITAL

DIGITALPanasonic

Panasonic

Maximum cabling distance of the extension line cord (twisted cable)The maximum length of the extension line cord (twisted cable) thatconnects the main unit and the extension is shown below:



24 AWG: Under 220 m 22 AWG: Under 360 m

Proprietary Telephone

DSS Console,KX-T7240


24 AWG: Under 220 m22 AWG: Under 360 m


Installation 2-13

Cable Pin Numbers to Be Connected

CONN.PIN261272

294305

327338

35103611

38133914

41164217

44194520

47224823

5025

CABLECOLOR

WHT-BLUBLU-WHTWHT-ORNORN-WHT

WHT-BRNBRN-WHTWHT-SLTSLT-WHT

RED-ORNORN-REDRED-GRNGRN-RED

RED-SLTSLT-REDBLK-BLUBLU-BLK

BLK-GRNGRN-BLKBLK-BRNBRN-BLK

YEL-BLUBLU-YELYEL-ORNORN-YEL

YEL-BRNBRN-YELYEL-SLTSLT-YEL

VIO-ORNORN-VIOVIO-GRNGRN-VIO

VIO-SLTSLT-VIO

CLIPNO.

1234

78910

13141516

19202122

25262728

31323334

37383940

43444546

4950

TR

D1D2

TR

D1D2

TR

D1D2

TR

D1D2

TR

D1D2

TR

D1D2

TR

D1D2

TR

D1D2

JackNo.1

JackNo.2

JackNo.3

JackNo.4

JackNo.5

JackNo.6

JackNo.7

JackNo.8

EXTN. 1-8 EXTN. 9-168EXTN†1 8EXTN†2 8EXTN†2

TR

D1D2

TR

D1D2

TR

D1D2

TR

D1D2

TR

D1D2

TR

D1D2

TR

D1D2

TR

D1D2

JackNo.9

JackNo.10

JackNo.11

JackNo.12

JackNo.13

JackNo.14

JackNo.15

JackNo.16

TR

D1D2

TR

D1D2

TR

D1D2

TR

D1D2

TR

D1D2

TR

D1D2

TR

D1D2

TR

D1D2

JackNo.17

JackNo.18

JackNo.19

JackNo.20

JackNo.21

JackNo.22

JackNo.23

JackNo.24

TR

D1D2

TR

D1D2

TR

D1D2

TR

D1D2

TR

D1D2

TR

D1D2

TR

D1D2

TR

D1D2

JackNo.25

JackNo.26

JackNo.27

JackNo.28

JackNo.29

JackNo.30

JackNo.31

JackNo.32

Notes • “8EXTN†1” in the table indicates an extension expansion area for KX-TD816. There are two expansion areas on the main unit. Up to onestation line unit can be installed to any area. It is required to designatewhich is Station Line Unit by System Programming.

• “8EXTN†2” in the table indicates an extension expansion area for KX-TD1232. There are three expansion areas on the main unit. Up to twostation line units can be installed to any area. It is required to designatewhich is Station Line Unit 1 and which is 2 by System Programming.

• If a telephone or answering machine with an A-A1 relay is connected tothe main unit, set the A-A1 relay switch of the telephone or answeringmachine to OFF position.

• Mis-connection may cause the system to operate improperly.


2-14 Installation

Connection of a Proprietary Telephone, KX-T7230, KX-T7235 or KX-T7250

4-conductor wiring is required for each extension.Connect pins “D1” and “D2” only.If the Method 2 in Section 2.3.4 “Paralleled TelephoneConnection,”and in Section 2.3.5 “EXtra Device Port (XDP)Connection”is used for parallel connection of a PT and a standardtelephone, connect pins “T,” “R,” “D1” and “D2.”

Connection of a Single Line Telephone, 2-conductor wiring is required for each extension. Connect pins “T” and “R.”

Connection of a DSS Console, KX-T7240 4-conductor wiring is required for each extension.Connect pins “D1” and “D2” only. (“T” and “R” are notnecessary.)

Notes • Up to four DSS Consoles can be installed for KX-TD816. Up to eightDSS Consoles can be installed for KX-TD1232 per system. As theDSS Console itself cannot work alone, it always requires a proprietarytelephone used in pair. Place the DSS Console and the paired telephoneside by side on your desk.

• It is necessary to designate the jack numbers of paired DSS Consolesand the proprietary telephones by System Programming.


Installation 2-15

Programming ReferencesSection 4, System Programming,[007] DSS Console Port and Paired Telephone Assignment[109] Expansion Card/Unit Type

Feature References Section 3, Features,DSS Console (KX-T7240)Module Expansion

Note After completing all the required inside cabling, including ISDN S0lines, extensions, external pagers, external music sources and so on,fasten the cables with the nylon tie (included) as shown.

1

2

3

4

26

1

27

2

1

2

3

4

Panasonic

DIGITAL

Station Wiring (2-pair twisted cabling):


50 Pin Connector Block Terminal

Green Line cordRed

Black

Yellow

Bridging Clips

2-16 Installation *: Available for KX-TD1232 only.

If you use the Clip Terminal to connect eight extensions, connect acable shown below to the clip terminal as follows. Refer to“Connection Chart” on the following page.

25

50

1

26

1:

2:

3:

4:

C:

C: continuous

20

19

18

17

16

15

14

13

12

11

10

9

8

7

6

5

4

3

2

1

20

19

18

17

16

15

14

13

12

11

10

9

8

7

6

5

4

3

2

1

40

39

38

37

36

35

34

33

32

31

30

29

28

27

26

25

24

23

22

21

40

39

38

37

36

35

34

33

32

31

30

29

28

27

26

25

24

23

22

21

IN OUT IN OUT

OUTIN

2.3.3 Optional Extension Connection of Clip Terminal*

Pin no.Clip no.

Clip Terminal

To Extensions

Cable (50 lines)

There are five kinds of dot for lines. You can distinguish a line by the number of dot and the color.

Cable(50 lines)

Connector type50-pin (amphenol 57JEseries or the equivalent)

*: Available for KX-TD1232 only. Installation 2-17

orange-red

orange-black

yellow-red

yellow-black

grey-red

grey-black

white-red

white-black

yellow-red

yellow-black

green-red

green-black

white-red

white-black

orange-red

orange-black

green-red

green-black

grey-red

grey-black

orange-red

orange-black

yellow-red

yellow-black

grey-red

grey-black

white-red

white-black

Pinno.

26

1

27

2

29

4

30

5

32

7

33

8

35

10

36

11

38

13

39

14

41

16

42

17

44

19

45

20

1

2

3

4

7

8

9

10

13

14

15

16

19

20

21

22

25

26

27

28

31

32

33

34

37

38

39

40

1

1

1

1

1

1

1

1

2

2

2

2

2

2

3

3

3

3

3

3

4

4

4

4

4

4

4

4

T

R

D1

D2

T

R

D1

D2

T

R

D1

D2

T

R

D1

D2

T

R

D1

D2

T

R

D1

D2

T

R

D1

D2

1, 9, 17

or 25

2, 10, 18

or 26

3, 11, 19

or 27

4, 12, 20

or 28

5, 13, 21

or 29

6, 14, 22

or 30

7, 15, 23

or 31

Cable Color

Clipno.

Numberof Dot

Jackno.

yellow-red

yellow-black

green-red

green-black

white-red

white-black

Pinno.

47

22

48

23

50

25

43

44

45

46

49

50

C

C

C

C

C

C

T

R

D1

D2

8, 16, 24

or 32

not use

Cable Color

Clipno.

Numberof Dot

Jackno.

Connection ChartThis chart is used for the Panasonic cable KX-A204 only.

EXAMPLE:

orange lineThe line of pin no.26

red

white line

black

The line of pin no.25

C : continuous

2.3.3 Optional Extension Connection of Clip Terminal*

2-18 Installation

Method 1: Using a Modular T-Adaptor

Any single line telephone can be connected in parallel with aproprietary telephone as follows:

2.3.4 Paralleled Telephone Connectionfor a Proprietary Telephone and a Single Line Telephone


Panasonic

Panasonic

DIGITAL

Panasonic

2-conductor wiring cord Connect the pin number of “ T” and “R”.

Modular T-Adaptor(Panasonic KX-J66 or USOC RJA2X)

4-conductor wiring cord For PT: Connect the pin number of“D1” and “D2”.

Proprietary Telephone(DPT=KX-T7230, KX-T7235, KX-T7250)



Installation 2-19


Panasonic

Panasonic

DIGITAL

TO EMSS TO TEL

XXXXX

Panasonic

Method 2: Using a PT Jack

2.3.4 Paralleled Telephone Connectionfor a Proprietary Telephone and a Single Line Telephone

Notes • Not only a single line telephone but a single line device such as ananswering machine, a facsimile or modem (personal computer) etc. canbe connected in parallel with a proprietary telephone.

• The KX-TD1232 is illustrated as a main unit.

Feature References Section 3, Features,Paralleled Telephone

2-conductor wiring cord Connect the pin number of “T” and “R” .

Single Line Telephone Proprietary Telephone(PT=KX-T7230, KX-T7235, KX-T7250)

4-conductor wiring cord Connect the pin number of “T” , “R”, “D1” and“D2”.

Rear of the telephone

To main unit (“TO EMSS” isprinted.)

To single linetelephone (“TOTEL” is printed.)

2-20 Installation

Method 1

Method 2Section 2.3.4 “Paralleled Telephone Connection, Method 2” is alsoavailable for XDP connection.

Note • The KX-TD1232 is illustrated as a main unit.

Programming ReferencesSection 4, System Programming,[600] EXtra Device Port

Feature References Section 3, Features,EXtra Device Port (XDP)

A proprietary telephone (KX-T7230, KX-T7235 or KX-T7250) anda single line telephone can be connected to the same extension jackyet have different extension numbers (eXtra Device Port feature).System Programming is required.

2.3.5 EXtra Device Port (XDP) Connectionfor a Proprietary Telephone and a Single Line Telephone


Panasonic

Panasonic

DIGITAL

Panasonic

4-conductor wiring cord Connect the pin number of “D1” and“D2”.

Proprietary Telephone(KX-T7230, KX-T7235, KX-T7250)


2-conductor wiring cord Connect the pin number of “T” and“R”.

Installation 2-21

Door opener 1

Doorphone

Doorphone adapter220V~LG

LOUB

~OV L O U B~12V~8V

Door opener 2

To

CL

b TO1 TO2 TS1 TS2a

2.3.6 Doorphone and Door OpenerConnection

A maximum of one doorphone and two door openers can beconnected per system. They are user-supplied devices.

: Speaker: Microphone: Protect Cover

LG: LightCL: Call button

Door opener 1

Doorphone

Doorphone adapter220V~LG

LOUB

~OV L O U B~12V~8V

Door opener 2

oT

CL

b TO1 TO2 TS1 TS2a

KX-TD816

KX-TD1232

2-22 Installation

2.3.6 Doorphone and Door OpenerConnection

Maximum cabling distance of the doorphone and the door opener lineThe maximum length of the doorphone and door opener line thatconnects to the main unit is shown below:

Note • The KX-TD1232 is illustrated as a main unit.

Programming ReferencesSection 4, System Programming,[122] Automatic Door Open[511] Door Opener Access[607]–[608] Doorphone Ringing Assignment — Day / Night

Feature References Section 3, Features,Door Opener Doorphone Call


Panasonic


22 AWG: Under 180 m

Doorphone

Door opener


2.3.7 External Relay, External Ringer andExternal Sensor Connection

A maximum of one user-supplied external relay, external ringerand/or external sensor can be connected per system.

Note • System Connection* permits a maximum of two of each device.

External Relay

Central Ringer

External Sensor

External Relay

Central Ringer

External Sensor

KX-TD816

KX-TD1232

2-24 Installation

— External RelayProgramming References

Section 4, System Programming,[213] External Relay Connecting Time[512] External Relay Access

Feature References Section 3, Features,External Relay

— External RingerProgramming References

Section 4, System Programming,[418] External Ringer Assignment[813] Floating Number Assignment

Feature References Section 3, Features,External Ringer

— External SensorProgramming References

No programming required.

Feature References Section 3, Features,External Sensor

2.3.7 External Relay, External Ringer andExternal Sensor Connection


Use an RCA connector and shielded cable.• Output impedance: 600 Ω

Maximum length of Cable18-22 AWG, under 10 m (33 feet)

A maximum of two external pagers (user-supplied) can beconnected per system as illustrated below.

Notes • System Connection* permits a maximum of four external pagers.• It is programmable that which external pager will send background

music and whether all the pagers will generate confirmation tone.• To adjust the sound level of the pagers, use the volume control on the

amplifiers.

Programming ReferencesSection 4, System Programming,[804] External Pager BGM[805] External Pager Confirmation Tone[813] Floating Number Assignment

Feature References Section 3, Features,Background Music (BGM) – External Paging – ExternalPaging – AllTrunk (CO Line) Answer From Any Station (TAFAS)

2.3.8 External Pager (Paging Equipment)Connection

Pager jack 1Pager jack 2

Amplifier

Amplifier

Speaker

SpeakerPaging equipment 2

Paging equipment 1

Pager jack 1Pager jack 2

Amplifier

Amplifier

Speaker

SpeakerPaging equipment 2

Paging equipment 1KX-TD816 KX-TD1232

2-26 Installation

2.3.9 External Music Source Connection

Up to two music sources such as a radio (user-supplied) can beconnected per system as illustrated below.

Insert the plug to the earphone / headphone jack on theexternal music source.Use a two-conductor plug 3.5 mm (9/64 inch) in diameter.• Input impedance: 8 ΩMaximum length of Cable18-22 AWG, under 10 m (33 feet)

Notes • System Programming of music sources used for Music on Hold andBackground Music is required.

• To adjust the sound level of the Music on Hold, use the volume controlon the external music source.

• The system is provided with an internal music source. By defaultsetting, internal music source is used as Music Source 1 for the systems.System Programming is required to select internal music source.

Programming ReferencesSection 4, System Programming,[803] Music Source Use[804] External Pager BGM[990] System Additional Information, Field (20)

Feature References Section 3, Features,Background Music (BGM) Background Music (BGM) – ExternalMusic on Hold


External Music Source 2





KX-TD816 KX-TD1232

Installation 2-27

2.3.10 Printer Connection

A user-supplied printer can be connected to the Serial Interface(RS-232C) Connector on the main unit. The printer is used to printout SMDR call records and system programming data.Connect the Serial Interface (RS-232C) connector of the printer tothe Serial Interface Connector. Cables must be shielded and themaximum length is 2 m (6.5 feet).

The pin configuration of Serial Interface (RS-232C) Connector isas follows:

PinNo.

12

34

56

78

20

FGSD (TXD)

RD (RXD)RS (RTS)

CS (CTS)CR (DSR)

SGCD (DCD)

ER (DTR)

EIA

AABA

BBCA

CBCC

ABCF

CD

CCITT

101103

104105

106107

102109

108.2

Frame GroundTransmitted Data

Received DataRequest To Send

Clear To SendData Set Ready

Signal GroundData Carrier Detect

Data TerminalReady

Circuit TypeSignal Name

Panasonic Serial Interface(RS-232C)

Serial Printer


2-28 Installation


Serial Interface (RS-232C)port on the main unit

Serial Interface (RS-232C)port on the printer/IBM-PC

Connection Chart for IBM Personal Computer (9-pin)

If you connect an IBM-PC to your system, see the chart below.

CircuitType(EIA)

AABA

BB

CB

ABCD

SignalName

FGSD (TXD)

RD (RXD)

CS (CTS)

SGER (DTR)

PinNo.

12

3

5

720

SignalName

RD (RXD)

SD (TXD)

SGCR (DSR)

RS (RTS)

CircuitType(EIA)

BB

BA

ABCC

CA

PinNo.

2

3

56

7

CircuitType(EIA)

AABB

BA

CDAB

CBCCCF

PinNo.

13

2

207

568

SignalName

FGRD (RXD)

SD (TXD)

ER (DTR)SG

CS (CTS)CR (DSR)CD (DCD)

CircuitType(EIA)

AABA

BBCB

CCAB

CD

SignalName

FGSD (TXD)

RD (RXD)CS (CTS)

CR (DSR)SG

ER (DTR)

PinNo.

12

35

67

20

Serial Interface (RS-232C)port on the main unit

Serial Interface (RS-232C)port on the printer/PC

Connection Chart for Printer / Personal Computer (25-pin)

Installation 2-29


Serial Interface (RS-232C) SignalsFrame Ground: FGConnects to the unit frame and the earth ground conductor of theAC power cord.

Transmitted Data: SD (TXD) ............................................(output)Conveys signals from the unit to the printer. A “Mark” condition isheld unless data or BREAK signals are being transmitted.

Received Data: RD (RXD) .................................................(input)Conveys signals from the printer.

Request to Send: RS (RTS)................................................(output)This lead is held ON whenever CR (DSR) is ON.

Clear To Send: CS (CTS) ...................................................(input)An ON condition of circuit CS (CTS) indicates that the printer isready to receive data from the unit. The unit does not attempt totransfer data or receive data when circuit CS (CTS) is OFF.

Data Set Ready: CR (DSR)................................................(input)An ON condition of circuit CR (DSR) indicates the printer is ready.Circuit CR (DSR) ON does not indicate that communication hasbeen established with the printer.

Signal Ground: SGConnects to the DC ground of the unit for all interface signal.

Data Terminal Ready: ER (DTR) .....................................(output)This signal line is turned ON by the unit to indicate that it is ON LINE. Circuit ER (DTR) ON does not indicate that communicationhas been established with the printer. It is switched OFF when theunit is OFF LINE.

Data Carrier Detect: CD (DCD) .......................................(input)The ON condition is an indication to data terminal (DTE) that thecarrier signal is being received.

2-30 Installation


Programming ReferencesSection 4, System Programming,[800] SMDR Incoming / Outgoing Call Log Printout[801] SMDR Format[802] System Data Printout[806]-[807] Serial Interface (RS-232C) Parameters – Port 1 / Port 2

Feature References Section 3, Features,Station Message Detail Recording (SMDR)System Programming and Diagnosis with Personal Computer

Digital Super Hybrid System KX-TD1232G Installation Manual

Documents

Transcript of Digital Super Hybrid System KX-TD1232G Installation Manual