Digital ic ajal crc
description
Transcript of Digital ic ajal crc
![Page 2: Digital ic ajal crc](https://reader035.fdocuments.us/reader035/viewer/2022081508/558104a0d8b42a05558b4569/html5/thumbnails/2.jpg)
Logic Family DefinitionLogic Family Definition• A circuit configuration or approach used to
produce a type of digital integrated circuit.• Consequence: different logic functions, when
fabricated in the form of an IC with the same approach, or in other words belonging to the same logic family, will have identical electrical characteristics.
• the set of digital ICs belonging to the same logic family are electrically compatible with each other
2
![Page 3: Digital ic ajal crc](https://reader035.fdocuments.us/reader035/viewer/2022081508/558104a0d8b42a05558b4569/html5/thumbnails/3.jpg)
•Three major logic families:
•TTL (Transistor-Transistor Logic) based on bipolar junction transistors
•CMOS (Complementary Metal Oxide Semiconductor) based on MOSFETs
•ECL (Emitter-Coupled Logic), based on bipolar junction transistors
•Originally, TTL chips were fast but used lots of power, and CMOS chips used little power but were slow.
•CMOS chips are sensitive to static discharge, and must be handled carefully.
Logic Families
![Page 4: Digital ic ajal crc](https://reader035.fdocuments.us/reader035/viewer/2022081508/558104a0d8b42a05558b4569/html5/thumbnails/4.jpg)
Common Characteristics of Common Characteristics of the Same Logic Familythe Same Logic Family
• Supply voltage range, speed of response, power dissipation, input and output logic levels, current sourcing and sinking capability, fan-out, noise margin, etc.
• Consequence: choosing digital ICs from the same logic family guarantees that these ICs are compatible with respect to each other and that the system as a whole performs the intended logic function.
4
![Page 5: Digital ic ajal crc](https://reader035.fdocuments.us/reader035/viewer/2022081508/558104a0d8b42a05558b4569/html5/thumbnails/5.jpg)
•In Electronic Devices & Circuits (EET 2201) you’ll study two major classes of transistors:
•Bipolar Junction Transistors (BJTs)
•Metal-Oxide Semiconductor Field Effect Transistor (MOSFETs)
Two Kinds of Transistors
![Page 6: Digital ic ajal crc](https://reader035.fdocuments.us/reader035/viewer/2022081508/558104a0d8b42a05558b4569/html5/thumbnails/6.jpg)
DIODE TRANSISTOR LOGICDIODE TRANSISTOR LOGIC
Y
What logic function is this circuit?
11011000
YAA
FILL IN THE TRUTH TABLE
DIODE TRANSISTOR LOGIC
B
A
0V
0V
+V5V
DIODE
DIODE
MMBT39041k
1k
![Page 7: Digital ic ajal crc](https://reader035.fdocuments.us/reader035/viewer/2022081508/558104a0d8b42a05558b4569/html5/thumbnails/7.jpg)
RTL ExampleRTL Example
7
![Page 8: Digital ic ajal crc](https://reader035.fdocuments.us/reader035/viewer/2022081508/558104a0d8b42a05558b4569/html5/thumbnails/8.jpg)
Basic Logic Families• TTL – transistor-transistor logic
based on bipolar transistors.• CMOS – complementary metal-oxide
semiconductor logic based on metal-oxide-semiconductor field effect transistors (MOSFETs).
• ECL – emitter coupled logic based on bipolar transistors.
![Page 9: Digital ic ajal crc](https://reader035.fdocuments.us/reader035/viewer/2022081508/558104a0d8b42a05558b4569/html5/thumbnails/9.jpg)
Basic Logic Families
TTL CMOS ECL
![Page 10: Digital ic ajal crc](https://reader035.fdocuments.us/reader035/viewer/2022081508/558104a0d8b42a05558b4569/html5/thumbnails/10.jpg)
General Characteristics of Basic Logic Families
• CMOS consumes very little power, has excellent noise immunity, and is used with a wide range of voltages.
• TTL can drive more current and uses more power than CMOS.
• ECL is fast, with poor noise immunity and high power consumption.
![Page 11: Digital ic ajal crc](https://reader035.fdocuments.us/reader035/viewer/2022081508/558104a0d8b42a05558b4569/html5/thumbnails/11.jpg)
Introduction
• Uses bipolar technology including NPN transistors, diodes and resistors.
• The NAND gate is the basic building block
• Contains different subfamilies with varying characteristics such as speed and power consumption
11
![Page 12: Digital ic ajal crc](https://reader035.fdocuments.us/reader035/viewer/2022081508/558104a0d8b42a05558b4569/html5/thumbnails/12.jpg)
Example Logic FamiliesExample Logic Families• General comparison or three commonly
available logic families.
the most important to understand
![Page 13: Digital ic ajal crc](https://reader035.fdocuments.us/reader035/viewer/2022081508/558104a0d8b42a05558b4569/html5/thumbnails/13.jpg)
Standard TTL NAND Gate
13
![Page 14: Digital ic ajal crc](https://reader035.fdocuments.us/reader035/viewer/2022081508/558104a0d8b42a05558b4569/html5/thumbnails/14.jpg)
What is a totem pole?
In art and history….
Totem poles are carved and painted vertical logs, constructed by many northwest coast native American Indian people. The poles display mythological images, animal spirits whose significance is their association with the lineage. 14
![Page 15: Digital ic ajal crc](https://reader035.fdocuments.us/reader035/viewer/2022081508/558104a0d8b42a05558b4569/html5/thumbnails/15.jpg)
Totem-Pole Output• Most chips you’ve used up to now
have had totem-pole outputs.
![Page 16: Digital ic ajal crc](https://reader035.fdocuments.us/reader035/viewer/2022081508/558104a0d8b42a05558b4569/html5/thumbnails/16.jpg)
Totem pole in TTL ?
• What is totem pole?– addition of an active pull up circuit in the
output of a gate is called totem pole. Using Q3 and Q4 to achieve this purpose
• Why totem pole?– To increase the switching speed of the
gate which is limited due to the parasitic capacitance at the output.
16
![Page 17: Digital ic ajal crc](https://reader035.fdocuments.us/reader035/viewer/2022081508/558104a0d8b42a05558b4569/html5/thumbnails/17.jpg)
Totem Pole Outputs
• The standard TTL output configuration with a HIGH output and a LOW output transistor, only one of which is active at any time.
• A phase splitter transistor controls which transistor is active.
![Page 18: Digital ic ajal crc](https://reader035.fdocuments.us/reader035/viewer/2022081508/558104a0d8b42a05558b4569/html5/thumbnails/18.jpg)
Totem Pole Outputs
![Page 19: Digital ic ajal crc](https://reader035.fdocuments.us/reader035/viewer/2022081508/558104a0d8b42a05558b4569/html5/thumbnails/19.jpg)
Advantages of Totem Pole Configuration
• Changes state faster than open-collector outputs.
• No external components are required.
![Page 20: Digital ic ajal crc](https://reader035.fdocuments.us/reader035/viewer/2022081508/558104a0d8b42a05558b4569/html5/thumbnails/20.jpg)
Totem Pole Switching Noise
• Caused by one output transistor turning off slower than the other turns on.
• Briefly shorts VCC to ground.
• Prevented with use of decoupling capacitors.
![Page 21: Digital ic ajal crc](https://reader035.fdocuments.us/reader035/viewer/2022081508/558104a0d8b42a05558b4569/html5/thumbnails/21.jpg)
NOT Gate 7404
21
![Page 22: Digital ic ajal crc](https://reader035.fdocuments.us/reader035/viewer/2022081508/558104a0d8b42a05558b4569/html5/thumbnails/22.jpg)
NOR Gate 7402
22
![Page 23: Digital ic ajal crc](https://reader035.fdocuments.us/reader035/viewer/2022081508/558104a0d8b42a05558b4569/html5/thumbnails/23.jpg)
AND Gate 7408
23
![Page 24: Digital ic ajal crc](https://reader035.fdocuments.us/reader035/viewer/2022081508/558104a0d8b42a05558b4569/html5/thumbnails/24.jpg)
OR Gate 7432
24
![Page 25: Digital ic ajal crc](https://reader035.fdocuments.us/reader035/viewer/2022081508/558104a0d8b42a05558b4569/html5/thumbnails/25.jpg)
XOR Gate
25
![Page 26: Digital ic ajal crc](https://reader035.fdocuments.us/reader035/viewer/2022081508/558104a0d8b42a05558b4569/html5/thumbnails/26.jpg)
Transistor-Transistor Logic Transistor-Transistor Logic FamiliesFamilies
• Transistor-Transistor Logic Families:– 74L Low power– 74H High speed– 74S Schottky– 74LS Low power Schottky– 74AS Advanced Schottky– 74ALS Advance Low power Schottky
![Page 27: Digital ic ajal crc](https://reader035.fdocuments.us/reader035/viewer/2022081508/558104a0d8b42a05558b4569/html5/thumbnails/27.jpg)
Standard TTL Transistor Switching Problem
• Trs are driven into deep saturation to fully conduct, or cutoff to switch off.
• The result of deep saturation is that the two junctions are now forward biased.
• The forward biasing of the BC junction forces a large number of minority carriers to the collector region.
• When the Tr switches off, these minority carriers needs to be removed. This takes a finite amount of time called the storage time (major component of the propagation delay) and thus increases the switch off time. 27
![Page 28: Digital ic ajal crc](https://reader035.fdocuments.us/reader035/viewer/2022081508/558104a0d8b42a05558b4569/html5/thumbnails/28.jpg)
MOSFET Types
• Depletion-mode.
• Enhancement-mode: – n-channel– p-channel
• CMOS (complementary) constructed from both n- and p-channel transistors.
![Page 29: Digital ic ajal crc](https://reader035.fdocuments.us/reader035/viewer/2022081508/558104a0d8b42a05558b4569/html5/thumbnails/29.jpg)
MOSFET Types
![Page 30: Digital ic ajal crc](https://reader035.fdocuments.us/reader035/viewer/2022081508/558104a0d8b42a05558b4569/html5/thumbnails/30.jpg)
MOSFETMOSFETMETAL OXIDE SEMICONDUCTORMETAL OXIDE SEMICONDUCTOR
FIELD EFFECT TRANSISTORSFIELD EFFECT TRANSISTORSP-CHANNEL ENHANCEMENTP-CHANNEL ENHANCEMENT N-CHANNEL ENHANCEMENTN-CHANNEL ENHANCEMENT
TO TURN ON GATE MUST BELOWER THAN SOURCE
TO TURN ON GATE MUST BEHIGHER THAN SOURCE
![Page 31: Digital ic ajal crc](https://reader035.fdocuments.us/reader035/viewer/2022081508/558104a0d8b42a05558b4569/html5/thumbnails/31.jpg)
TO TURN ONGATE LOWERTHAN SOURCE
DG
S
P-MOS VoutVin
C-MOS
P-MOS
N-MOS
TO TURN ONGATE HIGHERTHAN SOURCE
G
S
D
N-MOS0V
+V5V
10k
0V
5V
+V5V
+V5V
10k
TO TURN ONGATE LOWERTHAN SOURCE
DG
S
P-MOS VoutVin
C-MOS
P-MOS
N-MOS
TO TURN ONGATE HIGHERTHAN SOURCE
G
S
D
N-MOS0V
+V5V
10k
0V
5V
+V5V
+V5V
10k
MOSFETMOSFETMETAL OXIDE SEMICONDUCTORMETAL OXIDE SEMICONDUCTOR
FIELD EFFECT TRANSISTORSFIELD EFFECT TRANSISTORS
![Page 32: Digital ic ajal crc](https://reader035.fdocuments.us/reader035/viewer/2022081508/558104a0d8b42a05558b4569/html5/thumbnails/32.jpg)
MOSFET BIAS Requirements
• Operates in two modes:• Cutoff – acts as a very high
impedance between the drain and the source.
• Ohmic – equivalent of saturation. Acts like a relatively low resistance between the drain and the source.
![Page 33: Digital ic ajal crc](https://reader035.fdocuments.us/reader035/viewer/2022081508/558104a0d8b42a05558b4569/html5/thumbnails/33.jpg)
CMOSCMOSCOMPLIMENTARYCOMPLIMENTARY
METAL OXIDE SEMICONDUCTORMETAL OXIDE SEMICONDUCTOR
![Page 34: Digital ic ajal crc](https://reader035.fdocuments.us/reader035/viewer/2022081508/558104a0d8b42a05558b4569/html5/thumbnails/34.jpg)
CMOSCMOSCOMPLIMENTARYCOMPLIMENTARY
METAL OXIDE SEMICONDUCTORMETAL OXIDE SEMICONDUCTOR
VoutVin
C-MOS
P-MOS
N-MOS
0V
+V5V
![Page 35: Digital ic ajal crc](https://reader035.fdocuments.us/reader035/viewer/2022081508/558104a0d8b42a05558b4569/html5/thumbnails/35.jpg)
CMOS Quiescent vs. Dynamic Current
• Quiescent current flows when the gate is in a steady state and is usually small.
• Dynamic current flows when the gate is changing state.
• The faster a CMOS gate switches, the more current (and the more power) it requires.
![Page 36: Digital ic ajal crc](https://reader035.fdocuments.us/reader035/viewer/2022081508/558104a0d8b42a05558b4569/html5/thumbnails/36.jpg)
Power Dissipation
• The measure of energy used over time by electronic logic gates.
• The product of the voltage and current required for the operation of the circuit.
![Page 37: Digital ic ajal crc](https://reader035.fdocuments.us/reader035/viewer/2022081508/558104a0d8b42a05558b4569/html5/thumbnails/37.jpg)
Fan-InFan-In• Number of input signals to a gate
– Not an electrical property– Function of the manufacturing process
NAND gate with a Fan-in of 8
![Page 38: Digital ic ajal crc](https://reader035.fdocuments.us/reader035/viewer/2022081508/558104a0d8b42a05558b4569/html5/thumbnails/38.jpg)
Fanout Definitions
• Driving gate is the gate whose output supplies current to the inputs of other gates.
• Load gate is a gate whose input current is supplied by the output of another gate.
• A measure of the ability of the output of one gate to drive the input(s) of subsequent gates
![Page 39: Digital ic ajal crc](https://reader035.fdocuments.us/reader035/viewer/2022081508/558104a0d8b42a05558b4569/html5/thumbnails/39.jpg)
Fanout
• The number of gates that a logic gate is capable of driving without possible logic error.
• Limited by the maximum current a gate can supply in a given logic state versus the current requirements of the load.
![Page 40: Digital ic ajal crc](https://reader035.fdocuments.us/reader035/viewer/2022081508/558104a0d8b42a05558b4569/html5/thumbnails/40.jpg)
Fan out
• Also known as loading factor
• Defined as the maximum number of logic inputs that an output can drive reliably
• A logic circuit that specify to have 10 fan out can drive 10 logic inputs
©2009, CE Department
![Page 41: Digital ic ajal crc](https://reader035.fdocuments.us/reader035/viewer/2022081508/558104a0d8b42a05558b4569/html5/thumbnails/41.jpg)
• How many 74LS00 NAND gate inputs can be driven by a 74LS00 NAND gate outputs ?
Solution:
Refer to data sheet of 74LS00, the maximum values of
IOH = 0.4mA, IOL = 8mA, IIH = 20uA, and IIL = 0.4mA
Hence,
fan-out(high) = IOH(max) / IIH (max)=0.4mA/20uA=20
fan-out(low) = IOL(max) / IIL(max)=8mA/0.4mA=20,
the overall fan-out = fan-out(high) or fan-out(low) whichever is lower.
Hence, overall fan-out = 20
![Page 42: Digital ic ajal crc](https://reader035.fdocuments.us/reader035/viewer/2022081508/558104a0d8b42a05558b4569/html5/thumbnails/42.jpg)
ECL
![Page 43: Digital ic ajal crc](https://reader035.fdocuments.us/reader035/viewer/2022081508/558104a0d8b42a05558b4569/html5/thumbnails/43.jpg)
![Page 44: Digital ic ajal crc](https://reader035.fdocuments.us/reader035/viewer/2022081508/558104a0d8b42a05558b4569/html5/thumbnails/44.jpg)
ECLECLEMITTER COUPLED LOGICEMITTER COUPLED LOGIC
![Page 45: Digital ic ajal crc](https://reader035.fdocuments.us/reader035/viewer/2022081508/558104a0d8b42a05558b4569/html5/thumbnails/45.jpg)
8-14 The ECL Digital IC FamilyBasic ECL circuit – differential amplifier
The ECL Digital IC Family
This circuit produces complementary outputs: VOUT1 , equal to VIN ,
and VOUT2 , equal to VIN.
![Page 46: Digital ic ajal crc](https://reader035.fdocuments.us/reader035/viewer/2022081508/558104a0d8b42a05558b4569/html5/thumbnails/46.jpg)
8-14 The ECL Digital IC FamilyECL OROR/NORNOR Gate
The ECL Digital IC Family
The fundamental ECL gate.The basic ECL circuit can be
used as an INVERTER ifthe output is taken at VOUT1.
![Page 47: Digital ic ajal crc](https://reader035.fdocuments.us/reader035/viewer/2022081508/558104a0d8b42a05558b4569/html5/thumbnails/47.jpg)
8-14 The ECL Digital IC Family• ECL characteristics:– Very fast switching with typical propagation delay
of 360 ps—faster than TTL or CMOS.– The standard ECL logic levels are nominally
-0.8 V and 1.7 V for logical 1 and 0 respectively.– Worst-case noise margins approximately 150 mV.– ECL logic gates usually produce an output and its
complement, eliminating the need for inverters.– Current flow remains constant, eliminating noise
spikes
The ECL Digital IC Family
![Page 48: Digital ic ajal crc](https://reader035.fdocuments.us/reader035/viewer/2022081508/558104a0d8b42a05558b4569/html5/thumbnails/48.jpg)
![Page 49: Digital ic ajal crc](https://reader035.fdocuments.us/reader035/viewer/2022081508/558104a0d8b42a05558b4569/html5/thumbnails/49.jpg)
PLD’S
![Page 50: Digital ic ajal crc](https://reader035.fdocuments.us/reader035/viewer/2022081508/558104a0d8b42a05558b4569/html5/thumbnails/50.jpg)
PLD’sMost of these devices are based on a two level structure (sum of products form). AND
planeOR plane
Inputs
outputs
products
![Page 51: Digital ic ajal crc](https://reader035.fdocuments.us/reader035/viewer/2022081508/558104a0d8b42a05558b4569/html5/thumbnails/51.jpg)
In practice this might be represented as: A B C D
A.C + B.C D + A
•The fusible links are made at the x’s, otherwise blown.
PLD notation
outputs
inputs
![Page 52: Digital ic ajal crc](https://reader035.fdocuments.us/reader035/viewer/2022081508/558104a0d8b42a05558b4569/html5/thumbnails/52.jpg)
Inverted inputs A B
A.B + A.B
= B
A + B
outputs
inputs
![Page 53: Digital ic ajal crc](https://reader035.fdocuments.us/reader035/viewer/2022081508/558104a0d8b42a05558b4569/html5/thumbnails/53.jpg)
PLD’s
– The main types of PLD include:
• PLA’s (programmable logic arrays)
• PAL’s (programmable array logic)
• PROM’s (programmable read only memory)
![Page 54: Digital ic ajal crc](https://reader035.fdocuments.us/reader035/viewer/2022081508/558104a0d8b42a05558b4569/html5/thumbnails/54.jpg)
PLA’s A B
A programmable logic array (PLA) has all links programmable in both AND and OR arrays.
Very flexible.
Many applications don’t require such flexibility
![Page 55: Digital ic ajal crc](https://reader035.fdocuments.us/reader035/viewer/2022081508/558104a0d8b42a05558b4569/html5/thumbnails/55.jpg)
PALs– AND plane programmable
– OR plane fixed
– Not so flexible– Operate faster
because hard-wired OR’s switch quicker than programmed links.
A
B
AABB
F4 F1
F5 F8
P1
2
3
programmable links
![Page 56: Digital ic ajal crc](https://reader035.fdocuments.us/reader035/viewer/2022081508/558104a0d8b42a05558b4569/html5/thumbnails/56.jpg)
PAL’s• P = A.notB + notA.B• Use gate 1 to implement
the 1st product term and gate 2 to implement the second
• First term blow F2 and F3• Second term blow F5 and
F8
A
B
AABB
F4 F1
F5 F8
P1
2
3
![Page 57: Digital ic ajal crc](https://reader035.fdocuments.us/reader035/viewer/2022081508/558104a0d8b42a05558b4569/html5/thumbnails/57.jpg)
PALs Shorthand Notation
A B C D E
P
P = A.C.D
![Page 58: Digital ic ajal crc](https://reader035.fdocuments.us/reader035/viewer/2022081508/558104a0d8b42a05558b4569/html5/thumbnails/58.jpg)