diemorphing-dec09
-
Upload
dipti-bhavin-desai -
Category
Documents
-
view
216 -
download
0
Transcript of diemorphing-dec09
-
7/27/2019 diemorphing-dec09
1/3
SHEET METAL FORMING RESEARCH ASSOCIATION
(SMFRA)Prof. K. Narasimhan
Hon. SecretaryDept. of Metallurgical Eng. and Materials Sci.
I.I.T BombayPowai, Mumbai 400 076
INDIA
Phone : (022) 2576 7630
Fax : 091-22-2572 6975Email : [email protected]
Web: www.smfra.org
Workshop on
Die-Face Geometry Morphing
forSheet-Metal Springback Compensation
Dates: December 10 (Delhi/Gurgaon) 14 (Chennai) and 17 (Pune), 2009November 26, 2009
Dear Sir / Madam:
Sheet Metal Forming Research Association (SMFRA) is organizing a workshop focused on
highlighting the latest set of Computer-Based Techniques available for Morphing the Die Face
Geometry to account for Springback during the Engineering and Die Try-Out Stages. The workshop
will have a total of three pertinent presentations providing a comprehensive view of the techniques
employed to address this need. Presentations will be followed by a Brainstorming Session, where the
Workshop Participants will have the opportunity to describe current Springback Problems, and discuss
how the latest set of Die Face Morphing support techniques presented in the Workshop can
satisfactorily address their needs in this area. Please come prepared to discuss your issues,
problems, roadblocks, and potential needs.
We invite your participation in this event. Please note thatthere is no fee for participating in this
workshop. Please circulate this information to persons who would be interested in the program.
Looking forward to youremail confirmation, indicating also the city where you wish to participate.
K. Narasimhan
PROGRAMME DETAILS
Workshop Introduction
Springback Modeling and Prediction for effective Die Face Engineering,
Mr. Yogesh Soundattikar, Altair
3D Non-Contact Measurement (White Light Scanning) for minimizing Rework during Die
Try-Out Process, Mr. A. Gupta, APM Technologies
Die Face Morphing Based on Springback Analysis and/or Scan Based Measurements,
Dr. Sridhar Subramanyam, Rise Enterprise Solutions
Brainstorming Session
Venue Details and Start Time at Various Cities
Delhi/Gurgaon: December 10, 2009 Silver Oak, Phone: 0124-2387730-1; from 2:30 pm onwards
Chennai: December 14, 2009Hotel Savera; Phone: 044-2811 4700; from 4:00 pm onwards
mailto:[email protected]://www.smfra.org/mailto:[email protected]://www.smfra.org/ -
7/27/2019 diemorphing-dec09
2/3
Pune: December 17, 2009Electropneumatics & Hydraulics, Phone: 02135-667500; from 2:30 pm
onwards
Workshop on
Die-Face Geometry Morphing
forSheet-Metal Springback Compensation
Venue Details
At Gurgaon (Program Date: December 10, 2009, from 2:30 p.m.):
SILVER OAK
43, Akashneem Marg,
DLF City - 2,(Nr. Sahara Mall)
Gurgaon - 122 002
HARYANA.
India
Phone: 124-2387730/31/4052382
Email- [email protected]
Contact Person: Mr. Anand Sharma #Cell: 98731 59641)
At Chennai (Program Date: December 14, 2009, from 4:00 p.m.):
Hotel Savera
146 Radhakrishnan Salai
Chennai 600 004
Phone: 91-44-2811 4700
Contact Persons:
Mr.Abi. (cell: 9941006090)
Mr. Ravi (cell: 9710947368)
At Pune (Program Date: December 17, 2009), from 2:30 p.m.):
Electropneumatics & Hydraulics (India) Pvt. Ltd
Chakkan works, Kharabe Wadi, Gat. No. (New) 254/255, Chakkan Talegaon Road
Taluka Rajguru Nagar, Chakkan 410 501, Pune
Phone.: 02135-667500
http://gpo.iitb.ac.in/src/[email protected]://gpo.iitb.ac.in/src/[email protected] -
7/27/2019 diemorphing-dec09
3/3