Diagrama Navistar Breake Con Alisson
1
Pacbr ak e On/O ff swit ch 30 30 87A 87 85 97K 24B GY Pacbr ak e solenoid 10 amp Ignition power F4 Pin B Pin A PIN G Connec tor 372 Connec tor 3 86 86 85 NavPak ECM Pin 15 10 amp Navistar wir e 24A GY Ignition power Pin 47 Trans . rela y Pacbr ak e r ela y NOTES: • Pacbrake wiring kit contains toggle type switch, source Navistar rocker switch part number 1677051-C1 if desired. • The NavPak ECM requires exhaust brake circuit to be enabled. • Information for this schematic was derived from vehicle systems at the date of this printing. • Updates or variations by vehicle manufacturers constituting changes will not be the responsibility of Pacbrake. • Interface with ABS not required on vehicles with Allison MD3060 transmissions. Connec tor 379 Phone: 800-663-0096 • Fax: 604-882-9278 • E-mail: [email protected] • Internet: www.pacbrake.com Pacbrake® is a registered trademark of Pacbrake Company. Other trademarks used herein are property of their respective holders. Printed in Canada. L5227.0700 For vehicles: (WITH) Allison WT III Transmission (WITH OR WITHOUT) ABS Brake System (WITH) On-board air supply NAVISTAR DT466E/DT530E NAVPAK SYSTEMS NAVPAC EXHAUST BRAKE WIRING SCHEMATIC FOR: Allison ECU Optional customer furnished vehicle interface wiring connectors Allison gray plug Allison black plug Wire 132 engine brake enable output Wire 119 engine brake preselect request V V-3 S-11 S Note: Do not use on vehicles equipped with Allison 4th Generation Transmissions, they are identified by one connector at the transmission ECU, consult Pacbrake factory
-
Upload
eduardo-alvarez -
Category
Documents
-
view
47 -
download
10
Transcript of Diagrama Navistar Breake Con Alisson
Pacbr ak e On/O � swit ch
30 30
87A 8785
97K
24B GY
Pacbr ak esolenoid
10 amp IgnitionpowerF4
PinB
PinA
PING
Connec tor372
Connec tor3
86
86
85
NavP akECM
Pin 15
10 amp
Navistar wir e 24A GY
Ignitionpower
Pin 47
Trans . rela y Pacbr ak e rela y
NOTES:• Pacbrake wiring kit contains toggle type switch, source Navistar rocker switch part number 1677051-C1 if desired.• The NavPak ECM requires exhaust brake circuit to be enabled.• Information for this schematic was derived from vehicle systems at the date of this printing. • Updates or variations by vehicle manufacturers constituting changes will not be the responsibility of Pacbrake.• Interface with ABS not required on vehicles with Allison MD3060 transmissions.
Connec tor379
Phone: 800-663-0096 • Fax: 604-882-9278 • E-mail: [email protected] • Internet: www.pacbrake.comPacbrake® is a registered trademark of Pacbrake Company. Other trademarks used herein are property of their respective holders. Printed in Canada.
L5227.0700
For vehicles: (WITH) Allison WT III Transmission (WITH OR WITHOUT) ABS Brake System (WITH) On-board air supply
N A V I S T A R D T 4 6 6 E / D T 5 3 0 E N A V P A K S Y S T E M S N A V P A C E X H A U S T B R A K E W I R I N G S C H E M A T I C F O R :
AllisonECU
Optionalcustomerfurnished
vehicleinterface
wiringconnectors
Allisongray plug
Allisonblack plug
Wire 132engine brakeenable output
Wire 119engine brakepreselect request
V
V-3
S-11
S
Note: Do not use on vehicles equipped with Allison 4th Generation Transmissions, they are identified by one connector at the transmission ECU, consult Pacbrake factory
