Development of 3D Printing Strategies for Earth Materials...
Transcript of Development of 3D Printing Strategies for Earth Materials...
COMPUTING CRAFTManufacturing Cob Structures Using Robotically Controlled 3d PrintingConcluding remarks
Connected Everything: Industrial Systems in the Digital Age Conference - Nottingham - 25 June 2019
2
Introduction
Material exploration
3D printing equipment
Material extrusion system
Geometry and performance explorations
Future work
Subsoil
Straw
Water
Cob
Cob house in Dartington village in England. (CobBauge, 2018)
3
Regions with abundant clay in soil
4
Where Can You Build with Cob?
5
ODA Countries and Territories
The investigation was conducted in three stages:
• Investigate the current knowledge base of craft-
based cob-construction.
• Conduct initial geometrical and performance
exploration through small-scale modelling.
• Conduct a full-scale feasibility test for a cob
building element (building a wall/module).
6
7
The scheme of large scale robotic 3D printing set up (Gosselin et al. 2016)
3D printing
Equipment
Design &
Performance
Material
8
Material Exploration
Cob recipes are location-dependent.
Weismann, Adam and Katy Bryce. Building with Cob: A step-by-step guide, 40 – 65. Devon: Green Books Ltd, 2006.
On-site testing is always required.
Subsoil properties
80 % fine aggregate (sand, silt) + 20 % Clay
Subsoil 78% + water content 20 % + Straw 2 %
Cob recipe (by weight)
9
3D printing Equipment
Material extrusion system
3D printing Equipment
A
Air-assisted Extrusion
system
10
Material extrusion system
3D printing Equipment
B
Mechanical Extrusion system
(3D potter 7- Linear ram extruder)
11
Challenges
3D printing Equipment
Constant extrusion
Continuous flow
Higher speeds
Larger scale
Freedom of movement
12
13
Material extrusion system
14
Material extrusion system
15
Material extrusion system
16
Geometry and performance explorations
17
Small scale (1:4)
Simple geometries
Geometry exploration
18
Small scale (1:4)
Complex geometry A
Geometry Exploration
19
Small scale (1:4)
Complex geometry B
Geometry Exploration
20
1 2 3
Performance Exploration
Thermal conductivity (W/mK)
• The heat flow rate through a material.
• Lower thermal conductivity is
normally desired. Good practice: 0.6
W/mK.
• The heat flow meter used is a
Netzsch HFM 446.
Prototype 2 (0.32)
Prototype 4 (0.37)
Prototype 3 (0.40)
Prototype 1 (0.48)
Manual cob block (0.84)
0.10
0.20
0.30
0.40
0.50
0.60
0.70
0.80
0.90
1250.0 1350.0 1450.0 1550.0 1650.0 1750.0 1850.0C
onductivity W
/mK
Density Kg/m3
21
Performance Exploration
Thermal conductivity
• Presence of air gap(s)
lowered the conductivity of
the solid 3D printed cob
samples.
• Straw filling in the air gap(s)
further lowered the thermal
conductivity 2
1
3
Bigger scale (1:1)
Geometry Exploration
23
23
Bigger scale (1:1)
Geometry Exploration
Publications
• Veliz Reyes, A., Jabi, W., Gomaa, M., Chatzivasileiadi, A., Ahmad, L. and Wardhana, N.M. 2019.
Negotiated matter: a robotic exploration of craft-driven innovation. In Press. Architectural Science
Review Journal.
• Gomaa, M., Carfrae, J., Goodhew, S., Jabi, W. and Veliz Reyez, A. 2019. Thermal performance
exploration of 3D printed cob. Architectural Science Review 62 (3).
• Veliz-Reyes, A., Gomaa, M., Chatzivasileiadi, A., Jabi, W. and Wardhana, N. 2018. Computing
craft: development of a robotically-supported 3D printing system for cob structures. Presented
at: 36th annual Education and research in Computer Aided Architectural Design in Europe
(eCAADe) 2018, Lodz, Poland, 17-21 September 2018.
25
25
Future work
• Apply the technology in developing countries.
• Explore new material configurations.
• Explore new design and geometric opportunities.
• Conduct further performance testing (e.g. structural etc. on 1:1 scale).
Thank [email protected]