Detectable Warning Pavers · Web viewCompacted Aggregate Base 6” (150mm) thick Approx. 1”(25mm)...
Transcript of Detectable Warning Pavers · Web viewCompacted Aggregate Base 6” (150mm) thick Approx. 1”(25mm)...
SECTION 02780National Distribution 888-380-5575 DETECTABLE WARNING PAVERS
Detectable Warning PaversInstallation Diagrams
1. SAND SET INSTALLATIONA. OVER COMPACTED AGGREGATE BASE
© 2012 Tile Tech Pavers Inc, All Rights Reserved. Page 1 of 5
NOTES:1. Drain may be necessary in slow draining sub-grade.2. Base thickness varies with traffic, climate & sub-grade conditions.3. Concrete Pavers should be placed on a cement treated base if soil is
extremely weak or constantly saturated.4. Plastic, steel aluminum, or precast concrete edging may be used.5. Joints should be swept with sand.
Detectable Warning Pavers 2“ thickApprox. 1”(25mm) Bedding Sand / Cement
Compacted Aggregate Base 6” (150mm) thick
Compacted Soil Sub-grade
Existing Concrete CurbDetectable Warning Pavers 2“ thick
SECTION 02780National Distribution 888-380-5575 DETECTABLE WARNING PAVERS
Detectable Warning PaversInstallation Diagrams
2. SAND SET INSTALLATIONC. OVER EXISTING CONCRETE
© 2012 Tile Tech Pavers Inc, All Rights Reserved. Page 2 of 5
NOTES:1. Existing asphalt or concrete pavement shall be thoroughly inspected for
areas in need of patching or replacement. Conduct all repairs and fill all cracks greater than ¼” (7mm) wide prior to placing Geotextile, sand & pavers.
2. Provide drainage of sand layer through pea gravel-filled weep holes(s) or catch basin.
3. Joints should be swept with sand.
1” (25mm) Bedding Sand
Existing Aggregate Base
Geotextile over concrete. Turn up at curbExisting Concrete Pavement
Existing Soil Sub-grade2” (50mm) Dia. Drain Hole. Located at lowest elevations. Filled with Pea Gravel
SECTION 02780National Distribution 888-380-5575 DETECTABLE WARNING PAVERS
Detectable Warning PaversInstallation Diagrams
3. SAND SET INSTALLATIONB. OVER EXISTING ASPHALT
© 2012 Tile Tech Pavers Inc, All Rights Reserved. Page 3 of 5
1” (25mm) Bedding Sand
Existing Aggregate Base
Concrete Curb & Foundation (Local standards)Detectable Warning Pavers 2” thick
GeotextileExisting Asphalt Pavement
Existing Soil Sub-grade2” (50mm) Dia. Hole Filled With Pea Gravel Located at lowest elevations
NOTES:1. Existing asphalt or concrete pavement shall be thoroughly
inspected for areas in need of patching or replacement. Conduct all repairs and fill all cracks greater than ¼” (7mm) wide prior to placing Geotextile, sand & pavers.
2. Provide drainage of sand layer through pea gravel-filled weep holes(s)
3. Joints should be swept with sand.
Detectable Warning Pavers 2“ thick
SECTION 02780National Distribution 888-380-5575 DETECTABLE WARNING PAVERS
Detectable Warning PaversInstallation Diagrams
2. MORTAR SET INSTALLATIONB. THICK SET (BONDED) OVER CONCRETE
© 2012 Tile Tech Pavers Inc, All Rights Reserved. Page 4 of 5
Bond Coat
1” (25mm) Mortar Bed
Compacted Aggregate Base 6”(150mm) thick
Existing Soil Sub-grade
Mortar Bed Bond CoatConcrete Slab 4” (100mm) thick
NOTES:1. Concrete slab shall be sloped to provide complete surface drainage.
Provide subsurface drainage as required. 2. Slab to have steel trowel and fine broom finish. Do not use curing
compounds. Maximum variation in the slab ¼” in 10’.3. Expansion joints are mandatory. Architect must specify location and
details on drawings.4. This method is not recommended where the mortar bed is subjected
to freeze thaw cycles.5. Joints should be swept with sand or grouted.
Detectable Warning Pavers 2“ thick.
SECTION 02780National Distribution 888-380-5575 DETECTABLE WARNING PAVERS
Detectable Warning PaversInstallation Diagrams
2. MORTAR SET INSTALLATIONA. THIN SET OVER CONCRETE
© 2012 Tile Tech Pavers Inc, All Rights Reserved. Page 5 of 5
Latex Thin Set mortar bed spread per manufacturers recommendation
NOTES:1. Concrete slab shall be sloped to provide complete surface
drainage. Provide subsurface drainage as required.2. Slab to have steel trowel and fine broom finish. Do not use
curing compounds. Maximum variation in the slab ¼” in 10’.3. Expansion joints are mandatory. Architect must specify
location and details on drawings.4. Joints should be swept with sand or grout.
Concrete Slab 4” (100mm) thick
Compacted Aggregate Base 6”(150mm) thick
Existing Soil Sub-grade