Detailing Manual

download Detailing Manual

of 52

Transcript of Detailing Manual

  • 8/10/2019 Detailing Manual

    1/52

  • 8/10/2019 Detailing Manual

    2/523Detailing System

    Introducing the3M Automotive

    Detailing SystemA Complete System that Includes Cleaners,

    Dressings, Polishes, Waxes and more.

    Long the standard of quality and the preferred paint

    finishing system among automotive professionals, 3M offers

    a Detailing System for expanded customer

    satisfaction, increased worker safety, environmental

    compliance and product value.

    This state-of-the-art system incorporates several safer

    products, technological advancements for excellent

    results, easy dispensing systems and other innovations

    to achieve the ultimate in detailing system performance.

    This complete line is the only system you need to

    deliver quality detailed vehicles for expanded

    customer satisfaction.

    3M Detailing System

    For the Life of Your Car

  • 8/10/2019 Detailing Manual

    3/52

    Table of Contents

    SAFETY STATEMENT 3

    INSPECT AND PRE-CLEAN 4

    HEAVY CLEANING 6

    EXTERIOR CLEANING 8

    POLISHING, BUFFING, WAXING & EXTERIOR DRESSING 10

    INTERIOR CLEANING 12

    FINAL INSPECTION CHECKLIST 14

    BODY SHOP CLEAN-UP GUIDE 15

    PAINT FINISHING DOS AND DONTS 17

    PAINT REPAIR PROCEDURE 19

    DILUTION RATIOS 21

    DILUTER USAGE Installation / Troubleshooting 23

    PRODUCT INFORMATION 27

    DETAILING FINAL EXAM 43

    ORDERING INFORMATION 45

  • 8/10/2019 Detailing Manual

    4/523

    WARNING

    Before handling or using detailing chemicals, be sure to read

    the Material Safety Data Sheet (MSDS) for health hazard

    data, precautionary information, and suggested first aid.

    WARNING

    Fire hazard.

    Window Cleaner concentrate solution is flammable.

    Keep away from open flame; no smoking nearby.

    CAUTION

    Eye irritation -- wear eye protection when dispensing

    solutions and when replacing concentrate bottle solutions.

    Skin irritation -- wear rubber gloves when dispensingsolutions and when replacing concentrate bottle solutions.

    CAUTION

    Eye hazard.

    Flying particles and dust.

    Wear safety glasses with side shields when

    drilling or hammering.

    3M Detailing Products Safety Statement

    Read and understand all safety information before using this product.

    Wear appropriate personalprotective equipment to include:

    Boots

    Chemical resistant gloves

    Aprons

    Eye protection

    No loose fitting clothing or articles that may be caught in moving parts

    Avoid belts with buckles that may damage painted surfaces

    Avoid sharp objects that may damage leather or fabric upholstery

    SAFETYSTATEMENT

    Consult local regulation for VOC compliance.

    SAFETYSTATEMENT

  • 8/10/2019 Detailing Manual

    5/524

    3M Automotive Reconditioning Guide

    INSPECT & PRE-CLEAN

    Inspect the vehicle. Note any adhesive residue, tree sap, or bug spatters that will need to be specially treated. Use

    an air blower to remove leaves from trunk jambs and engine cowlings. Check for loose or missing caps on power

    steering, power brakes, oil filler, etc.; tighten or replace if necessary. Remove all trash from interior including trunk,

    ashtray, and seat folds. Inspect the interior carpet and fabric upholstery for any stains or heavily soiled areas that will

    require pre-spotting.

    Pre-spot any stained or heavily soiled interior carpet or fabric upholstery surfaces using 3M All Purpose Cleaner

    and Degreaser, diluted at 1:15 (1 part concentrate plus 15 parts water) and brush lightly. Pre-spotting and brushing

    greatly enhances the effectiveness of the cleaner and reduces the time needed to remove the stains later in the process.

    2.

    1.

  • 8/10/2019 Detailing Manual

    6/525

    3M Automotive Reconditioning Guide

    INSPECT & PRE-CLEAN

    Apply 3M Heavy Duty Wheel Cleaner to the wheels. Use the following steps to achieve maximum performance:

    Step 1: Determine which concentration to use based on experience.

    - Use a 1:2 dilution for lightly soiled wheels (1 part concentrate plus 2 parts water)

    - Use 100% concentrate for heavily soiled wheels (undiluted).

    Step 2: Spray 3M Heavy Duty Wheel Cleaner onto a DRY wheel. Pre-rinsing the wheel dilutes the product,

    reducing its effectiveness.

    DO NOT use 3M Heavy Duty Wheel Cleaner on glass, engines, anodized wheels and/or wheels with no

    coating or with coating cracked or in poor condition. Glass that is stained by the 3M Heavy Duty Wheel

    Cleaner can not be repaired and will need to be replaced.Note: 3M Heavy Duty Wheel Cleaner does not contain hydrofluoric or other strong acids.

    Apply 3M All Purpose Cleaner and Degreaser, diluted at 1:15 (1 part concentrate plus 15 parts water), to the

    engine and engine compartment (lightly), tires, wheels, wheel wells, rocker panels, door and trunk jams, etc. Let

    stand for 1 to 2 minutes. Rinse or wipe down engine and engine compartment surfaces with towel.

    Note: 3M Heavy Duty Wheel Cleaner works best on brake dust, while 3M All Purpose Cleaner and Degreaser

    works best on other soils. For best results, use both products on wheels.

    4.

    3.

    IN

    SPECTANDPRECLEAN

  • 8/10/2019 Detailing Manual

    7/526

    3M Automotive Reconditioning Guide

    HEAVY CLEANING

    Scrub tires, wheels, and other heavily soiled areas as necessary. A medium stiffness bristled brush works best on

    tires and most wheels, however, for chrome wheels, a wash mitt or terry cloth towel often produces better results.

    Thoroughly rinse all of the exterior areas where 3M Heavy Duty Wheel Cleaner and/or 3M All Purpose Cleaner

    and Degreaser have been applied. Rinse or wipe down engine and engine compartment last.

    Do not spray or rinse water on sensitive electrical engine components.

    Note: It is recommended that you start the engine when rinsing or spraying

    the engine compartment with water.

    2.

    1.

  • 8/10/2019 Detailing Manual

    8/527

    3M Automotive Reconditioning Guide

    HEAVY CLEANING(CONTINUED)

    Remove any adhesive residue from the vehicles exterior surfaces using 3M Adhesive Remover with a towel or

    scrub pad. No longer available for sale in California. Suggested replacement: 3M General Purpose Adhesive

    Cleaner (PN 08984 or PN 08987).

    3.

    HEAVYCLEANING

  • 8/10/2019 Detailing Manual

    9/528

    3M Automotive Reconditioning Guide

    EXTERIOR CLEANING

    Apply 3M All Purpose Cleaner and Degreaser, diluted at 1:15 (1 part concentrate plus 15 parts water) onto

    any bug spatters.

    Wash the vehicle using 3M Car Wash Soap diluted at 1:100 (1 part concentrate plus 100 parts water) and a clean,

    soft, sponge, towel, wash mitt or 3M Detail Cloth. Start at the top and work downward, scrubbing the areas with

    bug spatters last.

    Note: 3M Car Wash Soap cleans effectively at a 1 to 100 dilution ratio. Increasing the concentration will increase

    the suds but will also be more difficult to rinse off.

    2.

    1.

  • 8/10/2019 Detailing Manual

    10/529

    3M Automotive Reconditioning Guide

    EXTERIOR CLEANING(CONTINUED)

    Optional step (if needed or necessary): Clay the vehicle as needed with 3M Perfect-It III Cleaner Clay using the

    diluted 3M Car Wash Soap as a lubricant. This step may also be done after the vehicle is dry using 3M

    Perfect-It Gloss Enhancer as a lubricant.

    Rinse the entire vehicle thoroughly and dry using a chamois or a clean, soft, cotton terry cloth towel.

    Optional step if needed or necessary: Remove any tree sap deposits on glass surfaces using 3M Glass Cleaner

    undiluted and a terry cloth towel. Inspect vehicle after wash to identify any tree sap or similar deposits that were

    not removed by washing.

    EXTERIORCLEANING

    4.

    5.

    3.

  • 8/10/2019 Detailing Manual

    11/5210

    3M Automotive Reconditioning Guide

    POLISHING, BUFFING, WAXING &

    EXTERIOR DRESSING

    1.

    Buffing PadCharacteristics

    Compound / PolishCharacteristics

    05703

    05719

    05704

    05705

    05713

    05723

    05725

    Aggressiveness

    Finish

    Coarse

    Fine

    05954 / 05955

    05973 / 05974

    38105

    05928 / 05929

    38116

    38133

    3811139030 / 38112

    Aggressiveness

    Finish

    Most Coarse

    Least Fine

    Least

    Most

    Polish as needed using the following guidelines:

    Recommended polishing steps:

    - Swirls and fine scratches:

    Step 1. Polish using 3M Detail Polish 108 with a 3M Perfect-It FoamPolishing Pad, PN 05725.

    Step 2. Wax.

    - Oxidation and medium scratches:

    Step 1. Polish using 3M Detail Polish 208 with a 3M Superbuff PolishingPad, PN 05705.

    Step 2. Polish using 3M Detail Polish 108 with a 3M Perfect-It FoamPolishing Pad, PN 05725.

    Step 3. Wax.

    - Heavy oxidation and coarse scratches:

    Step 1. Compound using 3M Detail Compound 308 with a 3M Superbuff III2 Plus 2 Buffing Pad, PN 05704.

    Step 2. Polish using 3M Detail Polish 108 with a 3M Perfect-It FoamPolishing Pad, PN 05725.

    Step 3. Wax.

    Polishing materials:

    - 3M Detail Compound 308 = fastest cut / coarsest finish- 3M Detail Polish 208 = less cut / finer finish

    - 3M Detail Polish 108 = least cut / finest finishPolishing pads:

    - 3M Superbuff III 2 Plus 2 Buffing Pad, PN 05704 = fastest cut / coarsest finish- 3M Superbuff Polishing Pad, PN 05705 = less cut / finer finish- 3M Perfect-It Foam Compounding Pad, PN 05723 = less cut / finer finish- 3M Perfect-It Foam Polishing Pad, PN 05725 = least cut / finest finish

  • 8/10/2019 Detailing Manual

    12/5211

    3M Automotive Reconditioning Guide

    POLISHING, BUFFING, WAXING &EXTERIOR DRESSING

    (CONTINUED)

    Wax the painted surfaces using 3M Detail Wax or 3M Perfect-ItShow Car Paste Wax or 3M Performance Finish for best results:Step 1. Apply a thin, uniform coating of wax or 3M Performance

    Finish. Allow Detail Wax or Paste Wax to dry to a haze.Step 2. Remove wax residue using a soft, cotton terry cloth towel.Step 3. Detail using a 3M Perfect-It Detailing Cloth.

    Dress the tires using 3M Tire Dressing or 3M Silicone Free TireDressing. Apply a thin, uniform coating to a clean, dry tire using asprayer or applicator pad. The level of gloss can be controlled by thethickness of of the coating.DO NOT USE 3M Tire Dressing or 3M Silicone Free Tire

    Dressing on motorcycles, bicycles, or other two-wheeled vehicles

    tires or seats. Avoid spraying onto brake rotors, brake drums or

    brake pedals.

    PO

    LISHING,BUFFING,WAXING

    &EXTERIORDRESSING

    3.

    2.

    3M Silicone FreeTire Dressing

    3M Tire Dressing

    Note: Allow 3M Silicone FreeTire Dressing to completely drybefore driving vehicle as sling(particularly from newer tires)may stain painted surfaces.

    3M PERFORMANCE FINISH FOR

    BEST RESULTS

    DIRECTIONS FOR USE

    Do not apply in direct sunlight or

    onto a hot surface. Wash and dryvehicle using 3M CarWash Soap (PN 39000).If paint is dull or oxidizeduse 3M One StepCleaner Wax (PN 39006)after washing the vehicle,but prior to using 3MPerformance Finish.

    HAND

    Step 1. Gently apply a thin, uniformfilm to the paint surface using a terry

    cloth wax applicator or a clean, soft,folded cotton terry cloth towel.Step 2. Remove residue and buff to ahigh gloss using a 3M MicrofiberDetail Cloth (PN 39016) or a clean,soft, cotton terry cloth towel.Step 3. Complete method one panelat a time.

    MACHINE

    Step 1. Apply a thin, uniform film tothe paint surface using a randomorbital polisher equipped with a clean,

    soft, terry cloth bonnet or DAequipped with a soft foam pad.Step 2. Buff to a high gloss with apolisher equipped with a clean, dry,terry cloth bonnet or by hand using a3M Microfiber Detail Cloth(PN 39016) or a clean, soft, cottonterry cloth towel.Step 3. Complete method one panelat a time.

  • 8/10/2019 Detailing Manual

    13/5212

    3M Automotive Reconditioning GuideINTERIOR CLEANING

    Clean the interior vinyl, plastic, leather, and rubber surfaces using 3M All Purpose Cleaner and Degreaser, dilutedat 1:30 (1 part concentrate plus 30 parts water) and a towel or brush. Dry the surface using a clean, dry terry clothtowel. Use an air blower with the towel for hard to reach places.Note: For cleaning heavily soiled vinyl or leather upholstery, use 3M All Purpose Cleaner and Degreaser, diluted at 1:15(1 part concentrate plus 15 parts water).

    Thoroughly clean the vehicles carpet and upholstery using an extraction machine with 3M All Purpose Cleaner andDegreaser diluted at 1:100).2.

    1.

  • 8/10/2019 Detailing Manual

    14/5213

    3M Automotive Reconditioning Guide

    INTERIOR CLEANING(CONTINUED)

    Dress the vehicles interior vinyl, plastic, leather, and rubber components using 3M Interior Dressing. Apply enoughdressing to achieve a uniform wet appearance. Wipe off excess dressing using a clean, soft, dry terry cloth towel.Note: - For a lower gloss, dilute 3M Interior Dressing 1:1 with water (1 part concentrate plus 1 part water).

    - For a higher gloss, use 3M Engine and Tire Dressing undiluted.

    Clean the vehicles windows using 3M Premium Glass Cleaner diluted at 1:14 (1 part concentrate plus 14 partswater) and a clean, soft, dry cotton terry cloth towel.CAUTION: DO NOT USE UNDILUTED 3M GLASS CLEANER ON INTERIOR VEHICLE SURFACES.THE

    CONCENTRATED PRODUCT WILL STAIN VINYL AND LEATHER, AND MAY STAIN OTHER SURFACES.

    Note: - In hot, humid weather conditions spray and clean one window at a time- Use 3M Glass Cleaner concentrate undiluted for removing tree sap from exterior windows.

    Thoroughly inspect the vehicle exterior. Use a 3M Perfect-It Detailing Cloth and/or 3M Perfect-It GlossEnhancer for final detailing.

    INTERIORCLEANING

    4.

    5.

    3.

  • 8/10/2019 Detailing Manual

    15/5214

    3M Customer Pre-Delivery

    Detailing Checklist

    Pre-Delivery Cleaning and Final Inspection: Responsibility:

    Inspect the vehicle ______________

    Adhesive residue, tree sap, bug spatters

    Leaves, debris in jambs and cowlings

    Loose or missing caps, tighten or replace

    Remove all trash from interior including trunk, ashtray, and seat folds

    Note stains or heavily soiled carpet or upholstery

    Pre-spot and brush stained or heavily soiled areas ______________

    Clean wheels and wheel wells ______________

    Clean engine ______________

    Removed tar and/or adhesive residue ______________

    Wash vehicle ______________

    Clay vehicle if needed ______________

    Removed tree sap if needed ______________

    Buff and wax vehicle ______________

    Compound removal from jambs, moldings, etc. ______________

    Dress tires ______________

    Interior cleaning:

    Removed all items from interior ______________

    Vacuum all surfaces ______________

    Presoak carpet and upholstery stains ______________

    Scrub stained areas with brush ______________

    Finish cleaning carpet and upholstery ______________

    Clean all interior surfaces, vinyl, leather ______________

    Dress all interior surfaces ______________

    Clean interior and exterior glass ______________

    Replaced all items in vehicle ______________

    Final exterior inspection ______________

  • 8/10/2019 Detailing Manual

    16/5215

    BODYS

    HOPCLEAN

    UPSYSTEM

    3M Body Shop Clean-Up

    SYSTEM GUIDE

    Inspect vehicle

    Pre-Spot heavily soiled interior spots with APC

    Apply HD Wheel Cleaner (Do not use on glass, engines, anodized wheels and/or

    wheels with no coating or with coating cracked or in poor condition.)

    - 3M Heavy Duty Wheel Cleaner (PN 38374/38375)

    Apply APC & Degreaser to engine compartment, wheels, tires, jams, etc...

    - 3M All-Purpose Cleaner & Degreaser (PN 38350/38351/38052)

    Brush tires/wheels as needed

    Rinse APC & Degreaser

    Remove tape or adhesive residue with GPAC or Adhesive Remover

    - 3M General Purpose Adhesive Cleaner (PN 08984/08986/08987)

    - 3M Adhesive Remover (PN 38080/38081/38082)

    Pre-soak bugs and/or compound residue with APC & Degreaser

    - 3M All-Purpose Cleaner & Degreaser (PN 38350/38351/38052)

    1.

    2.

    3.

    4.

    5.

    6.

    7.

    8.

    STEP 2

    STEP 3

    STEP 7

    STEP 8

    STEP 4

    STEP 2

    STEP 3

    STEP 7

    STEP 8

    STEP 4

  • 8/10/2019 Detailing Manual

    17/5216

    Wash total vehicle with Car Wash Soap

    - 3M Car Wash Soap (PN 38377/38378/38079)

    Clay paint overspray as required

    Rinse and dry

    Remove tree sap from glass with undiluted Glass Cleaner as required

    - 3M Glass Cleaner (PN 38399/38300/38101)

    Apply Final Glaze to fresh painted areas

    - 3M Perfect-It 3000 Final Glaze (PN 06067/06066)

    Dress tires with Silicone-Free Tire Dressing

    - 3M Silicone-Free Tire Dressing (PN 38327/38328)

    Clean interior with APC & Degreaser

    - 3M All-Purpose Cleaner & Degreaser

    (PN 38350/38351/38052)

    Clean interior and exterior windows with Glass Cleaner

    - 3M Glass Cleaner (PN 38399/38300/38101)

    Wipe vehicle with Detail Cloth and inspect

    - 3M Detail Cloth (PN 06016/06017/06018)

    Attach mirror hang tag with shop business card

    9.

    10.

    11.

    12.

    13.

    14.

    15.

    16.

    17.

    18.

    STEP 9

    STEP 10

    STEP 14

    STEP 16

    STEP 15

    STEP 9

    STEP 10

    STEP 14

    STEP 16

    STEP 15

  • 8/10/2019 Detailing Manual

    18/5217

    Paint Finishing Dos & Donts

    Removes defects such as deep scratches, dust nibs orexcessive orange peel

    Dry sand with Dual Action Sander, foam interface padrecommended for contours OR wet sand by hand

    Caution: Sanding through clear coat will require repainting

    Follow with Scratch Refinement Step and/orCompounding Step

    1. Sanding Step 4. Polishing Step

    Removes swirls, fine scratches and very mild stains For Dark Colors use finer polish and finer foam pads

    For Lighter Colors use more aggressive polish and foam pads

    Note: Swirls and imperfections remaining after this stepwill reoccur after waxing step products wash or wear off

    Follow with Waxing Step

    5. Waxing Step

    Waxing fills swirls, very minor scratches and imperfectionsby leaving a thin layer of wax protection

    Wax does little to further refine paint after the polishingstep. After wax is washed or worn away, the imperfec-tions remaining after polishing will reappear

    Apply a thin even coat

    Apply by hand on a damp pad

    Apply with a Dual Action Sander using:05729 3M Perfect-it Foam Polishing D/A Pad - 6 in.

    05739 3M Perfect-it Hookit II Foam D/A Glazing Pad

    05732 3M Perfect-it Hookit II DA FoamApplication Pad - 6 in.

    Removes imperfections, such as car wash scratches,medium to coarse scratches, medium oxidation and stains

    Use wool pad for faster and more aggressive cutting

    Use foam pad for slower and finer cutting

    Follow with Polishing Step

    3. Compounding Step

    Damp sand with 3M Trizact disc on Dual Action Sander

    Use foam interface pad for contours

    Produces Semi-polished finish

    Follow with Compounding Step

    2. Scratch Refinement Step

    ORDRY WET

    PAINTFINIS

    HINGDOSANDDONTS

  • 8/10/2019 Detailing Manual

    19/5218

    Hiding vs. RemovingPaint Defects

    While polishing and waxing a vehicle, you may havenoticed that some fine scratches became less visible oreven disappeared, only to reappear after the vehicle hasbeen washed a few times. By using the correct system ofproducts and procedures, many small paint defects canbe removed and will not reappear when the polish andwax are washed and worn away.

    To remove a defect from the paint surface, you mustremove the very thin layer of paint that contains thedefect by spending enough time with a compound or polish.By removing this thin layer of paint, you actually removethe defect. See Illustration 1.

    Some scratches, acid rain pits, or other more severedefects may not be able to be removed completely. If adefect goes too deep into the clear coat, sanding to thebottom of the defect may result in inadequate clear coat

    thickness, or may even require a repaint. See Illustration 2.Generally speaking, if you can feel a scratch with yourfingernail, you should not attempt to remove it completely.However, even without sanding, many deep scratches orother more severe defects that are compounded, polishedand waxed will be less noticeable.

    3M Perfect-It Foam Pads

    Instructions for Use:

    Recommended speed 1500 to 2000 R.P.M. Do notexceed 3000 R.P.M. Use only with 3M HookitSBS Backup Pad, PN 05717 or a 3M Perfect-ItBackup Pad, PN 05718.

    To Install:

    1. Center the compound pad on the backup pad.2. Press firmly and twist to insure good contact with

    backup pad.

    IMPORTANT:

    Use caution around trim or moldings to avoid snaggingor tearing the pad. Keep the pad flat, or nearly flat,on surface being compounded.

    To minimize the possibility of burning, reduce pressureover sharp convex/concave areas such as detail lines,fenders, etc. and keep surface wet with compound.

    3M Foam Pad Care and Cleaning Instructions:

    If pad becomes clogged, remove and install a cleanpad. Clean clogged pad as follows:

    1. Rinse in warm (up to 115F) water.2. Set wet pad face up on a flat surface and allow

    to dry.IMPORTANT:

    Rinse under water faucet. Do not use soap or cleaningsolvents. Do not machine wash or dry. Do not cleanpads with a buffing spur or screwdriver.

    3M Superbuff III Buffing Pad

    (double-sided wool pad)

    CAUTION:

    3M Superbuff III Buffing Pad can spin off air-drivenpolishers due to tools rapid stop. To avoid spin off,firmly tighten buff onto adapter. Use 7/8 in. wrenchto hold adapter while tightening buff.

    Buffing Pad Care and Cleaning Instructions:

    Periodically rake pad with buffing spur or air nozzleto remove excess rubbing compound or glaze. If padbecomes clogged, remove, turn over, reinstall andcontinue buffing, allowing used side to dry. Washingpad causes shrinkage of wool fibers. If washing isdesired, use only cool (6080 F) water. Do not usehot water, strong detergents or solvents. Use washingmachines with gentle agitation only. Machine dryingis not recommended.3M Perfect-It

    Foam Pad

    CORRECT

    3M Perfect-ItFoam Pad

    INCORRECT

    3M SuperbuffBuffing Pad

    CORRECT

    3M SuperbuffBuffing Pad

    INCORRECT

  • 8/10/2019 Detailing Manual

    20/52

    PAINTREPAIRPROCEDURE

    19

    New or Like New

    Swirls and Very

    Fine Scratches

    Heavy Swirls

    Fine Scratches

    Mild Stains

    Light Oxidation

    Coarse Scratches

    Heavy Oxidation

    Deep ScratchesExcessive Overspray

    Very Deep Scratches

    Virtually no imperfections

    Scratches / Swirls / Imperfections

    Visible only in sunlight

    Imperfections that can be seen in

    shade or fluorescent lighting, but

    appear as swirls in sunlight. This

    procedure is usually done on light

    to medium colored cars only.

    Imperfections easily seen in all

    lighting. Can usually be seen from

    some distance.

    Scratches plainly seen may have

    a white look. May be felt with a

    fingernail, but only very slightly.

    Scratches felt with a fingernail.BE CAREFUL!Abrasive removal of toomuch clear coat or sanding into basecolor coat may require repainting.

    Paint Condition DiagnosisSanding & Scratch

    Refinement

    Medium Scratches

    Car Wash Scratches

    Heavy StainsMedium Oxidation

    Imperfections easily seen in shade

    or fluorescent lighting. Scratches

    can usually be seen separate fromswirls in sunlight.

    TIP: When in doubt, use finer system first andthen use more aggressive system as required

    TIP: Buffing pads in compounding step arelisted most aggressive to finer finishing

    1

    3M Hookit IIFinishing Film Discs-or-

    3M ImperialWetordry PaperSheets

    3M TrizactHookit II Foam Discs

    2 1

    02075

    02021

    00850

    PAINTREPAIRPROCEDURE

  • 8/10/2019 Detailing Manual

    21/5220

    Repair Procedure

    Compounding Polishing Waxing

    Use Disc Pad PN 05251 (on DA Sander) and OptionalInterface Pad PN 05274 or by hand with Pad PN 05291

    2 Use 3M No.20 Sponge Pad PN 055263 Use with Superbuff Adapter PN 05710 and PN 05718

    4 For Dual Action Sander Application use Pad PN 05251 and Pad PN 05739 or PN 057325 Use with PN 05718 or PN 05717

    5 5

    5

    5

    53

    3M Detail Compound #308

    -and-

    3M Perfect-It III Compounding Pad

    -or-

    3M Superbuff III Buffing Pad

    -or-

    3M Superbuff III 2 Plus 2

    Buffing Pad

    -or-

    3M Perfect-It Foam Compounding Pad- 8 in.

    3M Detail Compound #308

    -and-

    3M Perfect-It III Compounding Pad

    -or-3M Superbuff III Buffing Pad

    -or-

    3M Superbuff III 2 Plus 2

    Buffing Pad

    -or-

    3M Perfect-It Foam Compounding Pad- 8 in.

    3M Perfect-It II Rubbing Compound-and-

    3M Perfect-It IIICompounding Pad-or-

    3M Superbuff IIIBuffing Pad-or-

    3M Superbuff III 2 Plus 2Buffing Pad

    3M Detail Compound #308-and-

    3M Perfect-It IIICompounding Pad-or-

    3M Superbuff IIIBuffing Pad-or-

    3M Superbuff III2 Plus 2 Buffing Pad-or-

    3M Perfect-ItFoamCompoundingPad- 8 in.

    3M Detail Polish #208-and-

    3M Perfect-It FoamCompounding Pad- 8 in.

    3M Detail Polish #108-and-

    3M Perfect-It FoamPolishing Pad-or-

    3M Perfect-It 3000Ultrafina SE-and-

    3M Perfect-It UltrafinaFoam Polishing Pad

    05719057030570405723

    0571905703

    05719057030570405723

    38105

    057190570305704

    05973

    381050572505751

    3813306068

    3M Detail Wax-or-

    3M Perfect-It ShowCar Paste Wax-or-

    3M PerformanceFinish-and-

    3M Perfect-ItIII Detailing Cloths

    060160601739526

    3811138112

    3M Detail Wax-or-

    3M Perfect-It Show

    Car Paste Wax-or-3M PerformanceFinish-and-

    3M Perfect-ItIII Detailing Cloths

    060160601739526

    3811138112

    3M Detail Wax-or-

    3M Perfect-It ShowCar Paste Wax-or-

    3M PerformanceFinish-and-

    3M Perfect-ItIII Detailing Cloths

    060160601739526

    3811138112

    3M Detail Wax-or-

    3M Perfect-It ShowCar Paste Wax-or-

    3M Performance Finish-and-

    3M Perfect-It III

    Detailing Cloths

    060160601739526

    3811138112

    3M Detail Wax-or-

    3M Perfect-It ShowCar Paste Wax-or-

    3M Performance Finish-and-

    3M Perfect-It IIIDetailing Cloths

    06016

    0601739526

    38111

    38112

    3M Detail Wax-or-

    3M Perfect-It ShowCar Paste Wax-or-

    3M PerformanceFinish-and-

    3M Perfect-ItIII Detailing Cloths

    060160601739526

    3811138112

    4 4

    4 4

    4 4

    4 4

    4 4

    4 4

    4 4

    3M Detail Wax-or-

    3M Perfect-It ShowCar Paste Wax-or-

    3M PerformanceFinish-and-

    3M Perfect-ItIII Detailing Cloths

    06016060173952638111

    38112

    5

    3M Detail Polish #108-and-

    3M Perfect-It Foam

    Polishing Pad-or-

    3M Perfect-It 3000Ultrafina SE-and-

    3M Perfect-It UltrafinaFoam Polishing Pad

    0572505751

    3813306068

    5

    3M Detail Polish #108-and-

    3M Perfect-It FoamPolishing Pad-or-

    3M Perfect-It 3000Ultrafina SE-and-

    3M Perfect-It UltrafinaFoam Polishing Pad

    0572505751

    3813306068

    5

    3M Detail Polish #108-and-

    3M Perfect-It FoamPolishing Pad-or-

    3M Perfect-It 3000Ultrafina SE-and-

    3M Perfect-It UltrafinaFoam Polishing Pad

    0572505751

    3813306068

    5

    05723 38116

    5

    3M Detail Polish #108-and-

    3M Perfect-It FoamPolishing Pad-or-

    3M Perfect-It 3000Ultrafina SE-and-

    3M Perfect-ItUltrafina FoamPolishing Pad

    0572505751

    3813306068

    5

    057040572338105

    3

    3

    3

  • 8/10/2019 Detailing Manual

    22/5221

    Product Dilution Ratios Explained

    Mix water-based chemicals with water to make ready-to-use products.

    Why

    - Safer for workers- Save money buying concentrates

    - Ratios pre-set to match the job- Better for the environment

    Dilution examples

    - 1:3 or one-to-three = 1 part concentrate + 3 parts water = 4 gallons of useable product

    - 1:15 or one-to-fifteen = 1 part concentrate + 15 parts water = 16 gallons of useable product

    Cost per gallon example

    - 1:4 = 1 part concentrate ($5.00) + 4 parts water ($0.00) = $5.00 for 5 gallons or $1.00 per useable gallon

    3M dilution suggestions

    See below

    DILUTIONRATIOS

    Label Mix Diluter Pre-mix Shop Mix

    SPRAY BOTTLE AUTOMATIC DILUTER BULK CONCENTRATE

  • 8/10/2019 Detailing Manual

    23/5222

    3M Detailing Product Diluter

    INSTALLATION & USE INSTRUCTIONS

    Read and understand all safety information before using this product.

    Intended Use

    The 3M Detailing Product Diluter is intended to be used to dilute and dispense selected water based 3M DetailingProducts. The diluter is designed to operate on typical city water supply pressures.

    Safety Information

    WARNING

    Before handling or using detailing chemicals, be sure toread the Material Safety Data Sheet (MSDS) for healthhazard data, precautionary information, and suggested

    first aid.

    WARNING

    Fire hazard.

    Window Cleaner concentrate solution is flammable.

    Keep away from open flame; no smoking nearby.

    CAUTION

    Eye irritation -- wear eye protection when dispensingsolutions and when replacing concentrate bottle solutions.

    Skin irritation -- wear rubber gloves when dispensingsolutions and when replacing concentrate bottle solutions.

    CAUTION

    Eye hazard. Flying particles and dust.Wear safety glasses with side shields

    when drilling or hammering.

    Miscellaneous Diluter and Accessory Parts

    Available from Shopware Inc.

    Phone # 1-800-877-9344

    Fax # 952-392-2018 for order form Other accessories parts/service available

    Shopware part numbers below

    Pay via Visa, MasterCard or American Express

    Part Number Description

    PD100 Diluter tip kit (5 kits with 14 sizes)

    PD101 Viton foot valve (blue color 5/kit)

    PD102 In-line check valve (blue color 3/kit)

    PD103 Pickup tube kit (1 tube, 3 weights, 3Viton foot valve)

    PD104 Diluter (PN 37711) selector switchPD105 Glass cleaner foot valve (gray color 5/kit)

    PD106 Rieke Spout Spigot (for 5 gallon round and

    one gallon plastic 2/kit)

    PD107 Male NPT Spigot (for 5 gallon cubes 2/kit)

    PD108 Utility funnel (16oz. 3/kit)

    PD109 Glass Cleaner in-line valve (gray color 3/kit)

    PD110 5-Shelf Stack Rack (for 5-gallon cubes;

    black color) Price includes shippingand handling.

    PD111 Conversion kit (PN 37712) to Glass Cleaner

    Viton is a registered trademark of Dupont Dow ElastomersL.L.C. Corporation.

  • 8/10/2019 Detailing Manual

    24/5223

    3M Detailing Product Diluter

    INSTALLATION & USE INSTRUCTIONS(CONTINUED)

    Installing the Diluter

    1. Open the carton and check contents.- The carton contains the diluter control console with attached concentrate supply tubes and dispenser tubes.- Also, there is a small bag that contains one spare bottle cap, mounting screws, and wall anchors.

    2. Remove the front cover from the control console.- Press in on the tabs on both sides of the control console and simultaneously lift the front panel off.

    3. Mark the location of 3 mounting screws on the wall.- Position the back plate of the control console against the wall at the desired location. (You may use a level to make sure

    the control console is straight, but this is not critical to operation.)

    - Mark the location of the mounting screws with a pen or pencil. There are two keyholes at the top of the plate and a slothole near the bottom, left side.

    4. Drill holes for screws.- Use a 5/16 drill bit to make holes for the 3 wall anchors. You may need to use a masonry drill bit for some types of wall.

    5. Insert wall anchors.- Hammer the anchors flush to the wall.

    6. Insert top two screws- Screw in the top two screws, but leave the heads out about 1/4 from the wall.- Do not install the third screw yet.

    7. Secure the backplate to the wall- Do not over tighten the screws.

    - Place the console backplate on the wall. The keyholes at the top should fit over the two screw heads in the wall and slipdown into the keyhole notches.

    - Install the bottom screw and then tighten all three screws.

    8. Attach the water supply.- Thread the end of a standard garden hose to the connector on the right side of the control console (as you face the unit).

    - Note: The cap on the connector on the left side (as you face the unit) should normally remain in place.

    9. Snap the front cover into place.

    - Press in on the two side tabs while pushing the cover on until it snaps into place.

    10. Arrange concentrate containers below diluter so hoses are neatly arranged.

    - Each supply tube has a label on it to identify the concentrate product it supplies.- Insert each concentrate supply tube into its correct concentrate container and fasten the lid.

    CAUTION

    Eye hazard.

    Flying particles and dust.Wear safety glasses with side shields when drilling or hammering.

    IMPORTANTInspect to be sure the tubes are attached securely.The tube for

    supplying glass cleaner concentrate to the diluter is a special tube andmust be used for the glass cleaner concentrate. Do not switch tubes.

    DILUTERUSAGE

  • 8/10/2019 Detailing Manual

    25/5224

    Using the Diluter

    Dispense Heavy Duty Wheel Cleaner:

    - Place a correctly labeled detailing spray bottle onto the corresponding product tube coming out the bottom of thediluter console.

    - Press and hold correct button until bottle is filled.

    Dispense Glass Cleaner or All Purpose Cleaner & Degreaser:

    - Place a correctly labeled detailing spray bottle onto the corresponding product tube coming out the bottom of thediluter console.

    - Press and hold correct button until bottle is filled.

    Dispense Car Wash Soap:- The long tube on the right bottom of the console is for dispensing soap into a bucket on the floor.

    Place the end of the tube in a bucket.- Press and hold the right button, labeled Car Wash Soap, until youve dispensed the amount you want.

    IMPORTANT

    Make sure the supply tubes are inserted into their correctconcentrate product containers.

    The chart above shows the dilution ratios of water to various 3M detailing products. The eductor, labeled at the top,can be brown, grey, or yellow. The eductor is the part in the assembly that the hoses attach to. Find your educ-

    tor color and look below it to find the product you are using. In the column below your product, you willsee various dilution ratios. Find your ratio and follow it left to determine which dilution tip color youwill use. Example: Brown eductor with a black dilution tip has a dilution ratio of 1:2 of 3M

    Heavy Duty Wheel Cleaner to water.

    Depending on your hose fitting size you may have a snap tip or a threaded tip. If you

    are using a threaded dilution tip, it is important that you screw hand tight plus a1/4 turn. If you are using a snap dilution tip, fully insert it into the barbed

    fitting (be sure not to squeeze the tip).

    **Requires 3M Diluter Conversion Kit for Glass Cleaner(PD111) (Shopware 1-800-877-9344)

  • 8/10/2019 Detailing Manual

    26/5225

    3M Detailing Product Diluter

    TROUBLESHOOTING GUIDE

    DILUTERUSAGE

    Excessive foam in 3M Heavy Duty Wheel Cleaner (whenfilling, bottle is more than 1/2 full of foam)

    Tighten the fitting where the 3M Heavy Duty WheelCleaner suction hose meets the diluter

    3M Car Wash Soap not sudsy enoughReplace yellow orifice tip with brown, orange or greenorifice tip

    No siphon on select product(s)Ensure all fittings are very tight and secure.Replace foot valveon the end of the hose.Ensure adequate water pressure

    Water leaks where garden hose attaches to diluter Ensure rubber washer is inside fitting. Tighten the fitting

    Water leaks where gray water hose fitting meets whitevalve housing

    Unscrew gray fitting, reapply thread sealer/tape, screwfitting back in

    After use, suction hose drains down or loses primeReplace foot valve on the end of the hose. Note: Use grayfoot valve for 3M Glass Cleaner and a blue foot valve for

    all other products.

    While in use, water spits out from gray or yellow eductor

    Mineral deposits inside eductor misdirecting water flow;

    remove eductor and soak/clean with lime-away typeproduct and reinstall.**

    After usage, solid crystals develop in 3M Glass Cleanersupply hose

    Remove supply hose, clean out crystals, and reinstall or

    replace selector switch or install separate 3M SingleProduct Diluter PN 37712 with Glass Cleaner ConversionKit PD111 (Available from Shopware 1-800-877-9344)

    After usage, residue builds up around and inside selectorswitch causing difficult operation or reduced suction*

    Replace selector switch or disassemble and clean selectorswitch with water. Note: Pay attention to how the switchcomes apart for exact re-assembly

    PROBLEM: SOLUTION:

  • 8/10/2019 Detailing Manual

    27/5226

    No discharge

    a. Open water supply.

    b. Install valve parts kit.c. Install regulator if water pressure exceeds 60 PSI (flowing).

    d. Clean** or replace.

    No concentrate draw

    a. Clean or replace.

    b. Clean (descale)** or replace.

    c. Minimum 20 PSI (with water running) required to operate

    unit properly.

    d. Push tube firmly onto eductor discharge hose barb; besure inner discharge tube is installed and has flooding ring.

    e. Replace with full container.

    f. Tighten, but do not overtighten.

    g. Disconnect inlet water line and clean strainer.

    Excess concentrate drawa. Press correct tip firmly into barb on eductor.

    b. Place concentrate below the eductor.

    Failure of unit to turn off

    a. Clean** or replace with valve parts kit.

    b. Make sure magnet moves freely.

    c. Remove button and clean cabinet/button to remove any

    dirt lodged in slide recess

    Excess foaming in dischargea. Put clamp on tube or replace tube if brittle.

    b. Install inner discharge tube.

    Water discharge from air vents on eductor

    a. Be sure discharge tube is not immersed, kinked orelevated. Be sure there is no liquid in the discharge tube

    when beginning to operate dispenser.

    b. Install pressure regulator if flowing water pressureexceeds 60 PSI (flowing).

    PROBLEM: SOLUTION:

    * Applies only to old model with selection switch (37711)

    ** In hard water areas, scale may form inside the discharge end of the eductor, as well as in other areas of the unit that are

    exposed to water. This scale may be removed by soaking the eductor in a descaling solution (deliming solution). Toremove an eductor located in the cabinet, firmly grasp water valve and unthread eductor. Replace in same manner.

    Alternatively, a scaled eductor can be cleaned (or kept from scaling) by drawing the descaling solution through the unit.Operate the unit with the suction tube in the descaling solution. Operate the unit until solution is drawn consistently, then

    flush the unit by drawing clear water through it for a minute. Replace concentrate container and put suction tubeinto concentrate.

  • 8/10/2019 Detailing Manual

    28/5227

    3M Heavy Duty Wheel CleanerPRODUCTINFORMATION

    A water based cleaner concentrate for removing brake dust from

    vehicle wheels. Does not contain hydrofluoric or other strong acids.

    - PN 38374 (38074)* 1 gallon bottle

    - PN 38375 (38075)* 5 gallon pail- PN 38076 55 gallon drum

    3M Heavy Duty Wheel Cleaner is a cleaner concentrate designed

    to remove tough brake dust deposits from wheels.

    Directions for Use:

    1. Add 1 part cleaner concentrate to 2 parts water.

    2. Apply 3M Heavy Duty Wheel Cleaner to vehicle wheels andlet stand for about 2 minutes.

    Note: 3M Heavy Duty Wheel Cleaner works best whenapplied to a dry wheel.

    3. Apply 3M All Purpose Cleaner and Degreaser (1:15 dilution)to the tires and wheels. Let stand for approximately

    one minute.*

    4. Rinse thoroughly, using a high-pressure washer.5. For particularly stubborn brake dust deposits, use 3M Heavy Duty Wheel Cleaner undiluted.

    *Note: 3M Heavy Duty Wheel Cleaner works best for removing brake dust, while 3M All Purpose Cleaner and

    Degreaser works best for cleaning tires and removing other difficult soils from wheels.DO NOT use 3M Heavy Duty Wheel Cleaner on glass, engines, anodized wheels and/or wheels with no

    coating or with coating cracked or in poor condition. Glass that is stained by the 3M Heavy Duty Wheel

    Cleaner can not be repaired and will need to be replaced.

    Note: 3M Heavy Duty Wheel Cleaner does not contain hydrofluoric or other strong acids.

    Tips:

    - For heavy brake dust deposits agitation with a brush greatly enhances cleaning effectiveness.- Light agitation on some chrome wheels greatly enhances the final appearance.

    - For removing water spots, apply 3M Heavy Duty Wheel Cleaner diluted at 1 part cleaner concentrate to 2 partswater to the vehicles painted surfaces, let stand two minutes but do not allow to dry, scrub using a terry cloth toweland rinse.

    Product Safety and Health Information Source:Material Safety Data Sheet(MSDS 08-3012-5) or

    3M Automotive Aftermarket Division3M Center, Bldg. 223-6N-01St. Paul, MN 55144-1000

    Telephone: 1-877-MMM-CARS (1-877-666-2277) or (651) 737-6501

    * Part number to be discontinued

    PAINTSHOPSAFE!

  • 8/10/2019 Detailing Manual

    29/5228

    A water based cleaner/degreaser concentrate for exterior and interiorvehicle cleaning.

    - PN 38350 (38050)* 1 gallon bottle

    - PN 38351 (38051)* 5 gallon pail- PN 38052 55 gallon drum

    3M All Purpose Cleaner and Degreaser is a heavy duty cleanerconcentrate designed for both interior and exterior vehicle cleaning

    applications. 3M All Purpose Cleaner and Degreaser removes oil,

    grease, and other tough soils from vehicle engines, tires, wheels, and otherheavily soiled exterior vehicle surfaces, and is very effective for removinginsect residue from the fronts of vehicles. 3M All Purpose Cleaner and

    Degreaser also cleans and removes soils and most stains from carpet,fabric upholstery, vinyl, leather, and other interior vehicle surfaces.

    Directions for Use:

    DILUTION 1:15 (Add 1 cup concentrate to a gallon containerand fill with water.) Use for degreasing, tire and wheel cleaning,

    insect residue removal, carpet and upholstery stain removal, andother heavy duty cleaning applications.

    DILUTION 1:30 (Add 1/2 cup concentrate to a gallon container and fill with water.) Use for cleaning vinyl, leather,

    plastic and other lightly soiled vehicle surfaces.

    Degreasing/Insect Residue Removal: (1:15 dilution)1. Spray diluted cleaner onto heavily soiled areas engines, tires, wheels, insect residue, etc. Let stand about 2 minutes.2. Scrub/brush heavily soiled areas as needed.

    3. Rinse thoroughly using a high pressure washer.

    Carpet/Fabric Upholstery Cleaning (1:15 dilution)

    1. Spray diluted cleaner directly onto the surface.

    2. Work the surface using the appropriate sponge, cloth, or brush.3. Remove soil using an extraction unit.

    Vinyl/Leather Light Duty Cleaning (1:30 dilution)

    1. Spray the diluted cleaner directly onto the surface, or spray onto a terry cloth towel and apply.

    2. Work the surface using the appropriate sponge, cloth, or brush.3. Remove soil using a clean, dry terry cloth towel.

    Tips:- For maximum effectiveness do not allow degreaser to dry before rinsing.- For heavily soiled wheels; first apply 3M Heavy Duty Wheel Cleaner, soak two minutes, then apply

    3M All Purpose Cleaner and Degreaser (1:15 dilution), soak one minute, scrub as needed and rinse.

    Product Safety and Health Information Source:

    Material Safety Data Sheet (MSDS 16-3418-7) or

    3M Automotive Aftermarket Division3M Center, Bldg. 223-6N-01

    St. Paul, MN 55144-1000Telephone: 1-877-MMM-CARS (1-877-666-2277)

    or (651) 737-6501

    * Part number to be discontinued

    3M All Purpose Cleaner and Degreaser

    PAINTSHOPSAFE!

  • 8/10/2019 Detailing Manual

    30/5229

    PRODUCTINFORMATION

    3M Glass Cleaner

    A solvent based water dilutable cleaner concentrate.

    - PN 38399 (38099)* 1 gallon can- PN 38300 (38100)* 5 gallon pail- PN 38101 55 gallon drum

    (special order)

    3M Glass Cleaner is a concentrated cleaner that quickly andeffectively removes smoke films, fingerprints and other soils from

    windows and plastic surfaces, and may also be used to assist in theremoval of window stickers and adhesive residue. 3M GlassCleaner does not contain ammonia and will not leave a filmy residue.

    Directions for Use:

    CAUTION: DO NOT USE UNDILUTED 3M GLASS CLEANER

    ON INTERIOR VEHICLE SURFACES. THE CONCENTRATED

    PRODUCT WILL STAIN VINYL AND LEATHER, AND MAY STAIN

    OTHER SURFACES.

    CAUTION: DO NOT USE 3M GLASS CLEANER ON FRESHLY

    PAINTED SURFACES.

    1. Add 1 part concentrate to 14 parts water (add 1 cup to 1 gallon of water).

    2. Spray onto the glass or plastic surface and rub thoroughly using a clean, soft, dry cotton terry cloth towel.3. Remove the final material with a clean, soft, dry terry cloth towel.

    Tips:

    - To ensure optimum performance, always use fluorinated 3M Detailing Spray Bottles with 3M Glass Cleaner.- In hot, humid weather conditions spray one window at a time and wipe immediately.

    - Use 3M Glass Cleaner concentrate undiluted for removing tree sap from exterior windows.

    Product Safety and Health Information Source:

    Material Safety Data Sheet(MSDS 08-2999-4) or

    3M Automotive Aftermarket Division3M Center, Bldg. 223-6N-01

    St. Paul, MN 55144-1000Telephone: 1-877-MMM-CARS (1-877-666-2277) or (651) 737-6501

    * Part number to be discontinued

    PAINTSHOPSAFE!

  • 8/10/2019 Detailing Manual

    31/5230

    3M Premium Glass Cleaner

    A solvent based water dilutable cleaner concentrate.

    Excellent for high humidity conditions.

    - PN 38221 1 gallon can

    - PN 38222 5 gallon pail

    Directions for Use:

    CAUTION: DO NOT USE UNDILUTED 3M GLASS CLEANER

    ON INTERIOR VEHICLE SURFACES.THE CONCENTRATED PRODUCT WILL STAIN VINYL AND

    LEATHER, AND MAY STAIN OTHER SURFACES.

    CAUTION: DO NOT USE 3M GLASS CLEANER ON FRESHLY

    PAINTED SURFACES.

    1. Add 1 part concentrate to 14 parts water (add 1 cup to 1 gal-

    lon of water).

    2. Spray onto the glass or plastic surface and rub thoroughly

    using a clean, soft, dry cotton terry cloth towel.

    3. Remove the final material with a clean, soft, dry terry cloth

    towel.

    Tips:

    - To ensure optimum performance, always use fluorinated 3M Detailing Spray Bottles with 3M Glass Cleaner.- In hot, humid weather conditions spray one window at a time and wipe immediately.

    - Use 3M Glass Cleaner concentrate undiluted for removing tree sap from exterior windows.

    Product Safety and Health Information Source:

    Material Safety Data Sheet

    (MSDS 08-2999-4) or

    3M Automotive Aftermarket Division

    3M Center, Bldg. 223-6N-01

    St. Paul, MN 55144-1000

    Telephone: 1-877-MMM-CARS (1-877-666-2277) or (651) 737-6501

    PAINTSHOPSAFE!

  • 8/10/2019 Detailing Manual

    32/5231

    3M Car Wash Soap

    A highly concentrated water based soap.

    - PN 38377 (38077)* 1 gallon bottle

    - PN 38378 (38078)* 5 gallon pail

    - PN 38079 55 gallon drum

    3M Car Wash Soap is a highly concentrated liquid soap which

    develops heavy-bodied, long-lasting suds and quickly removes dirt

    and road film from exterior automotive surfaces.

    Directions for Use:

    1. Add 1 part soap concentrate to 100 parts water in a clean

    bucket (about 2/3 cup in five gallons water).

    2. Rinse the vehicle thoroughly to remove any grit that could

    scratch the paint surface.

    3. Wash the vehicle using a clean, soft, sponge, towel or

    wash mitt.

    4. Rinse thoroughly and dry using a clean, soft, cotton terry

    cloth towel or chamois.

    Product Safety and Health Information Source:

    Material Safety Data Sheet

    (MSDS 08-3014-1) or

    3M Automotive Aftermarket Division

    3M Center, Bldg. 223-6N-01

    St. Paul, MN 55144-1000

    Telephone: 1-877-MMM-CARS (1-877-666-2277) or (651) 737-6501

    * Part number to be discontinued

    PAINTSHOPSAFE!

  • 8/10/2019 Detailing Manual

    33/5232

    A solvent based product that quickly removes adhesive residue.

    - PN 38080 1 gallon can

    - PN 38081 5 gallon pail

    - PN 38082 55 gallon drum

    3M Adhesive Remover is a ready-to-use blend of petroleum sol-

    vents designed to remove adhesive deposits from exterior vehicle

    surfaces. To minimize the possibility of staining, do not apply in

    direct sunlight or onto a hot surface.

    Directions for Use:

    1. Soak cloth with 3M Adhesive Remover and apply onto

    the surface.

    2. Rub thoroughly with a soft cloth and remove the excess

    material with a clean, dry, soft cloth. Repeat as necessary.

    3. For stubborn deposits, apply material, allow to soak for one

    minute and scrub.

    Tips:

    - For difficult oil-based stains on fabric apply 3M Adhesive Remover, scrub, and clean using 3M All Purpose Cleaner

    and Degreaser or 3M Multi-Purpose Cleaner.

    - Use 3M Premium Glass Cleaner concentrate undiluted for removing tree sap from exterior windows.

    Product Safety and Health Information Source:

    Material Safety Data Sheet

    (MSDS 08-4315-1) or

    3M Automotive Aftermarket Division

    3M Center, Bldg. 223-6N-01

    St. Paul, MN 55144-1000

    Telephone: 1-877-MMM-CARS (1-877-666-2277) or (651) 737-6501

    *Not for sale in California. Suggested replacement: 3M General Purpose Adhesive Cleaner (PN 08984 or 08986 or 08987)

    3M Adhesive Remover*

    PAINTSHOPSAFE!

  • 8/10/2019 Detailing Manual

    34/5233

    3M Interior DressingPRODUCTINFORMATION

    A ready-to-use water based silicone dressing.

    - PN 38086 1 gallon bottle

    - PN 38087 5 gallon pail

    3M Interior Dressing is a ready-to-use water-based silicone

    emulsion designed to restore a natural gloss appearance to all vinyl,

    leather, rubber and plastic interior vehicle surfaces.

    Directions for Use:

    1. Spray onto a clean, soft, cotton terry cloth towel and wipe onto

    the surface, or spray directly onto the surface and wipe. Use

    enough material to achieve a uniform appearance.

    2. Wipe off excess material using a clean, soft, dry terry cloth

    towel to achieve a natural look and feel.

    Tips:

    - For a lower gloss dilute 3M Interior Dressing 1:1 with water.

    - For a higher gloss use 3M Engine and Tire Dressing undiluted.

    Product Safety and Health Information Source:Material Safety Data Sheet

    (MSDS 08-3134-7) or

    3M Automotive Aftermarket Division

    3M Center, Bldg. 223-6N-01

    St. Paul, MN 55144-1000

    Telephone: 1-877-MMM-CARS (1-877-666-2277) or (651) 737-6501

  • 8/10/2019 Detailing Manual

    35/5234

    Awater based silicone engine and tire dressing concentrate.

    - PN 38124 1 gallon bottle

    - PN 38125 5 gallon pail

    - PN 38126 55 gallon drum

    3M Engine and Tire Dressing is a water-based silicone emulsion

    concentrate, designed to restore a deep black appearance on tires,

    hoses and rubber moldings, and a clean new look on vinyl, plastic,

    and other low gloss or flat painted surfaces.

    Directions for Use:

    1. For dressing engines, add 1 part concentrate to 1 part water;

    or for dressing tires, apply concentrate.

    2. Apply a uniform coating directly onto the surface and allow to

    dry naturally.

    Tips:

    - For higher gloss, use 3M Engine Dressing undiluted.

    - Great tire dressing where low VOCs are required.

    - 3M Engine and Tire Dressing may be used undiluted as a tire dressing or an interior dressing:

    1. Apply a uniform coating to the surface.

    2. Remove excess using a terry cloth towel.

    Product Safety and Health Information Source:

    Material Safety Data Sheet

    (MSDS 08-6460-3) or

    3M Automotive Aftermarket Division

    3M Center, Bldg. 223-6N-01

    St. Paul, MN 55144-1000

    Telephone: 1-877-MMM-CARS (1-877-666-2277) or (651) 737-6501

    3M Engine and Tire Dressing

  • 8/10/2019 Detailing Manual

    36/5235

    3M Tire Dressing

    A solvent based ready-to-use silicone tire dressing.

    - PN 38127 1 gallon can

    - PN 38128 5 gallon pail

    - PN 38129 55 gallon drum

    3M Tire Dressing is a solvent based silicone dressing that

    produces a deep black, glossy appearance on new and nearly new

    tires, and a deep black, natural appearance on older tires.

    Directions for Use:

    1. Spray a thin, uniform coating onto a clean, dry tire. Wipe

    lightly with a clean, soft, terry cloth towel and allow to dry.

    2. Remove overspray from wheels, hubcaps, or painted surfaces

    using a clean, soft dry terry cloth towel.

    DO NOT USE on motorcycles, bicycles, or other two-wheeled

    vehicles tires or seats. Avoid spraying onto brake rotors,

    brake drums or brake pedals.

    Tips:

    - For a higher gloss appearance apply dressing and allow to dry without wiping.

    - For lower VOC requirements use 3M Engine and Tire Dressing (see page 34.)

    Product Safety and Health Information Source:

    Material Safety Data Sheet

    (MSDS 08-6461-1) or

    3M Automotive Aftermarket Division

    3M Center, Bldg. 223-6N-01

    St. Paul, MN 55144-1000

    Telephone: 1-877-MMM-CARS (1-877-666-2277) or (651) 737-6501

    P

    RODUCTINFORMATION

  • 8/10/2019 Detailing Manual

    37/5236

    A solvent based, ready-to-use silicone free tire dressing.

    - PN 38327 (38227)* 1 gallon can

    - PN 38328 (38228)* 5 gallon pail

    3M Silicone Free Tire Dressing is a solvent based silicone free

    dressing that produces a deep black, glossy appearance on new and

    nearly new tires, and a deep black, natural appearance on older tires.

    It is critical to follow the directions for use for 3M Silicone Free

    Tire Dressing to avoid the possibility of paint staining.

    Directions for Use:

    Note: Sling from some, particularly newer, tires may

    stain painted surfaces. To avoid staining, follow these

    instructions carefully.

    1. Clean tires thoroughly using 3M All Purpose Cleaner and

    Degreaser 1:15 or stronger and scrub using a stiff bristle brush.

    2. Thoroughly rinse the tires using a pressure washer and allow

    to dry.

    3. Apply a thin, uniform coating of 3M Silicone Free Tire Dressing using a trigger sprayer, sponge applicator, or rag.

    Note: Use only a thin coating of dressing. A heavy coating may puddle around tire treads or raised lettering, and spatter

    even after the dressing dries.

    4. Remove excess dressing using an absorbent cloth.5. Allow dressing to dry completely before driving the vehicle.

    DO NOT USE on motorcycles, bicycles, or other two-wheeled vehicles tires or seats.

    Avoid spraying onto brake rotors, brake drums or brake pedals.

    Product Safety and Health Information Source:

    Material Safety Data Sheet

    (MSDS 16-2924-5) or

    3M Automotive Aftermarket Division

    3M Center, Bldg. 223-6N-01

    St. Paul, MN 55144-1000

    Telephone: 1-877-MMM-CARS (1-877-666-2277)

    or (651) 737-6501* Part Number To Be Discontinued

    3M Silicone Free Tire Dressing

    PAINTSHOPSAFE!

  • 8/10/2019 Detailing Manual

    38/5237

    3M Perfect-It III Cleaner Clay

    A clay bar for removing overspray and environmental contaminates

    from a vehicles exterior surfaces.

    - PN 38070 200 gram bar

    3M Perfect-It III Cleaner Clay is recommended for use in

    removing contaminants such as rail dust, paint overspray, and

    industrial fallout from exterior paint, glass, and metal surfaces.

    Directions for Use:Do not use in direct sunlight or on a hot surface.

    1. Wash and rinse vehicle thoroughly using 3M Car Wash Soap.

    2. Check exterior surfaces for contaminants a rough or gritty feel.

    3. Work contaminated areas with the clay using light pressure and 3M Car Wash Soap or 3M Perfect-It Gloss

    Enhancer as a lubricant.

    4. Rinse and dry surface.

    5. Knead clay periodically to expose a new surface.

    Tips:

    - Use 3M Perfect-It III Cleaner Clay with 3M Car Wash Soap as a lubricant while washing the vehicle, or use 3M

    Perfect-It III Cleaner Clay with 3M Perfect-It Gloss Enhancer (contains silicone) as a lubricant after the vehicle

    has been washed.

    Product Safety and Health Information Source:

    Material Safety Data Sheet

    (MSDS 08-5407-5) or

    3M Automotive Aftermarket Division

    3M Center, Bldg. 223-6N-01

    St. Paul, MN 55144-1000

    Telephone: 1-877-MMM-CARS (1-877-666-2277) or (651) 737-6501

    PAINTSHOPSAFE!

    P

    RODUCTINFORMATION

  • 8/10/2019 Detailing Manual

    39/5238

    A light cutting very fine finishing polish. Contains silicones.

    - PN 38133 1 gallon bottle

    3M Detail Polish 108 is a light cutting, very fine finishing polish

    recommended for use to remove light oxidation, fine scratches and

    stains, and leaves an excellent, high gloss finish on all types of

    automotive paints. To minimize the possibility of staining, do not

    apply in direct sunlight or onto a hot surface.

    Note: Contains silicones. Not recommended for use in body shop or

    paint shop applications.

    Directions for Use:

    Polish using an electric buffer (1000 to 2500 RPM) equipped with

    a 3M Superbuff Polishing Pad or a 3M Perfect-It Foam

    Polishing Pad.

    1. Shake container before using.

    2. Apply enough polish to the paint surface to work a 2 x 2

    area. To minimize slinging, spread the polish over the surface

    with the pad before starting the machine.

    3. Start the machine and buff using light-to-medium pressure.

    4. Reduce pressure as polish begins to dry, and buff to a high gloss. Clean pad as necessary to assist cleanup.

    Tips:

    Excellent for the first step of a 2-step buffing procedure.

    Step 1 Use 3M Detail Compound 308 with a 3M Superbuff Compounding Pad to remove imperfections such as

    heavy oxidation, car wash scratches or other coarse scratches.

    Step 2 Use 3M Detail Polish 208 with a 3M Perfect-It Foam Polishing Pad to remove the compound swirl

    marks and product the best finish.

    Product Safety and Health Information Source:

    Material Safety Data Sheet

    (MSDS 08-5425-7) or

    3M Automotive Aftermarket Division

    3M Center, Bldg. 223-6N-01St. Paul, MN 55144-1000

    Telephone: 1-877-MMM-CARS (1-877-666-2277) or (651) 737-6501

    3M Detail Polish 108

  • 8/10/2019 Detailing Manual

    40/5239

    3M Detail Polish 208PRODUCTINFORMATION

    A medium cutting fine finishing polish. Contains silicones.

    - PN 38116 1 gallon bottle

    3M Detail Polish 208 is a medium cutting, fine finishing polish

    recommended for use to remove oxidation, scratches and stains,

    and leaves a high gloss finish on all types of automotive paints. To

    minimize the possibility of staining, do not apply in direct sunlight or

    onto a hot surface.

    Note: Contains silicones. Not recommended for use in body shop or

    paint shop applications.

    Directions for Use:

    Polish using an electric buffer (1000 to 2500 RPM) equipped with

    a 3M Superbuff Polishing Pad or a 3M Perfect-It Foam

    Compounding Pad.

    1. Shake container before using.

    2. Apply enough polish to the paint surface to work a 2 x 2 area.

    To minimize slinging, spread the polish over the surface with

    the pad before starting the machine.

    3. Start the machine and buff using light-to-medium pressure.

    4. Reduce pressure as polish begins to dry, and buff to a high gloss. Clean pad as necessary to assist cleanup.

    Tips:

    Excellent for use with a 3M Perfect-It Foam Compounding Pad to remove light oxidation, fine scratches, and stains

    and leaves a high gloss finish in a one step process.

    Product Safety and Health Information Source:

    Material Safety Data Sheet

    (MSDS 09-0268-4) or

    3M Automotive Aftermarket Division

    3M Center, Bldg. 223-6N-01

    St. Paul, MN 55144-1000

    Telephone: 1-877-MMM-CARS (1-877-666-2277) or (651) 737-6501

  • 8/10/2019 Detailing Manual

    41/5240

    A medium cutting fine finishing compound. Contains silicones.

    - PN 38105 1 gallon bottle

    3M Detail Compound 308 is a medium cutting, fine finishingcompound recommended for use to remove heavy oxidation, coarse

    scratches and stains, and leaves a medium gloss, fine swirl markfinish on all types of automotive paints. To minimize the possibility of

    staining, do not apply in direct sunlight or onto a hot surface.

    Note: Contains silicones. Not recommended for use in body shop orpaint shop applications.

    Directions for Use:

    Compound using an electric buffer (1000 to 2500 RPM)

    equipped with a 3M Superbuff Compounding Pad, or a3M Perfect-It Foam Compounding Pad.1. Shake container before using.

    2. Apply enough compound to the paint surface to work a 2x2area. To minimize slinging, spread the compound over the

    surface with the pad before starting the machine.3. Start the machine and buff using light to medium pressure.

    4. Reduce pressure as the compound begins to dry. Clean pad as necessary to assist cleanup.

    Tips:

    Excellent for the first step of a 2-step buffing procedure.

    Step 1 Use 3M Detail Compound 308 with a 3M Superbuff Compounding Pad to remove imperfections such asheavy oxidation, car wash scratches or other coarse scratches.

    Step 2 Use 3M Detail Polish 208 with a 3M Perfect-It Foam Polishing Pad to remove the compound swirlmarks and product the best finish

    Product Safety and Health Information Source:

    Material Safety Data Sheet

    (MSDS 09-6468-4) or

    3M Automotive Aftermarket Division

    3M Center, Bldg. 223-6N-01St. Paul, MN 55144-1000

    Telephone: 1-877-MMM-CARS (1-877-666-2277) or (651) 737-6501

    3M Detail Compound 308

  • 8/10/2019 Detailing Manual

    42/52

    PRODUCTINFORMATION

    A carnauba wax based durable liquid wax. Contains silicones.

    - PN 38111 1 gallon

    3M Detail Wax is an easy to use, durable automotive wax

    recommended for use on new or like new paint finishes to producea deep, high gloss, lustrous finish. To minimize the possibility of

    staining, do not apply in direct sunlight or onto a hot surface.

    Note: Contains silicones. Not recommended for use in body shop orpaint shop applications.

    Directions for Use:

    1. Apply a thin, uniform coating of wax to the paint surface, either

    by hand or with an orbital action tool equipped with a foam pad.Allow to dry to a haze.

    2. Remove wax residue and buff to a high gloss using a soft,

    cotton terry cloth towel.

    Product Safety and Health Information Source:

    Material Safety Data Sheet(MSDS 09-2788-9) or

    3M Automotive Aftermarket Division

    3M Center, Bldg. 223-6N-01St. Paul, MN 55144-1000

    Telephone: 1-877-MMM-CARS (1-877-666-2277) or (651) 737-6501

    3M Detail Wax

    41

    3M Perfect-It Gloss EnhancerA water based spray detailing product. Contains silicones.

    - PN 38113 1 gallon bottle- PN 38114 5 gallon pail- PN 38115 55 gallon drum (special order)

    3M Perfect-It Gloss Enhancer is a quick and easy, spray on /

    wipe off product that can restore a just waxed look and feel. 3MPerfect-It Gloss Enhancer is also recommended for use as a spray

    detailing product to assist in the removal of buffing residue, and as alubricant for claying a vehicle.

    Note: Contains silicones. Not recommended for use in body shop or

    paint shop applications.

    Directions for Use:

    Do not apply in direct sunlight or onto a hot surface.1. Shake well before using.2. Remove any grit that could scratch the paint surface.

    3. Spray on and wipe off small areas one panel at a time.4. Remove any dried overspray with a damp cloth.

  • 8/10/2019 Detailing Manual

    43/5242

    Tips:

    - For a clay lubricant, use enough 3M Perfect-It Gloss Enhancer to completely wet the surface. After claying, wipeoff the residue before it dries.

    Product Safety and Health Information Source:

    Material Safety Data Sheet

    (MSDS 08-3020-8) or

    3M Automotive Aftermarket Division

    3M Center, Bldg. 223-6N-01St. Paul, MN 55144-1000Telephone: 1-877-MMM-CARS (1-877-666-2277) or (651) 737-6501

    A reactive silicone paint protector. Contains silicones.

    3M Performance Finish is a reactive silicone based product that

    bonds to the paint surface providing a durable, longlasting and high gloss protective finish with exceptional waterbeading qualities. The application and removal characteristics make

    this product extremely easy to use leaving a high gloss wet look fin-ish that is pleasing to the eye. Its more than a wax!

    Note: Contains silicones. Not recommended for use in body shop orpaint shop applications.

    Directions for Use:

    1. Apply a thin, uniform film to the paint surface, using a terrycloth wax applicator or a clean, soft, folded, cotton, terry cloth

    towel. Or use a random orbital polisher equipped with a clean,soft, terry cloth bonnet or DA equipped with soft

    foam pad.2. Remove residue and buff to a high gloss using a 3M Microfiber Detail Cloth (PN 39016) or a clean,

    soft, cotton terry cloth towel. Or, with a polisher equipped with a clean, dry, terry cloth bonnet.

    3. Complete method one panel at a time.

    Product Safety and Health Information Source:

    Material Safety Data Sheet

    (MSDS 18-5336-5) or

    3M Automotive Aftermarket Division3M Center, Bldg. 223-6N-01

    St. Paul, MN 55144-1000Telephone: 1-877-MMM-CARS (1-877-666-2277)

    or (651) 737-6501

    3M Performance Finish

    - PN 38112 quart bottle

    - PN 39030 pint bottle

    3M Perfect-It Gloss Enhancer(CONTINUED)

  • 8/10/2019 Detailing Manual

    44/5243

    DETAILINGFINALEXAM

    Detailing Final Exam

    3M Heavy Duty Wheel Cleaner will (may) cause damage on:

    a. Uncoated wheels or coated wheels in poor conditionb. Glass

    c. Enginesd. All of the Above

    The two recommended dilution ratios for 3M All Purpose Cleaner & Degreaser are:a. 1:15 and 1:25b. 1:12 and 1:25

    c. 1:15 and 1:30

    d. 1:10 and 1:20e. 1:8 and 1:16

    Which of the following is a concern or a potential problem when buffing with a foam pad?

    a. Easy to useb. Runs hotterc. No lint

    d. Minimal swirlse. None of the above

    What product would you use to remove a coffee stain from a carpeted floor mat?a. 3M All Purpose Cleaner & Degreaser diluted 1:30

    b. 3MAll Purpose Cleaner & Degreaser diluted 1:15c. 3M Heavy Duty Wheel Cleaner

    d. 3M Gloss Enhancere. None of the above

    What product would you recommend for removing hard water spots from a painted or plastic surface?

    a. 3M Heavy Duty Wheel Cleaner diluted 1:2 (Do not use on glass, engines, anodized wheels and/or

    wheels with no coating or with coating cracked or in poor condition.)

    b. 3M All Purpose Cleaner & Degreaser diluted 1:15

    c. 3M Heavy Duty Wheel Cleaner undiluted (Do not use on glass, engines, anodized wheels and/or wheelswith no coating or with coating cracked or in poor condition.)

    d. 3M All Purpose Cleaner & Degreaser diluted 1:30e. None of the above

    If a product is diluted 1:8 and costs $18 per gallon, what is the cost per diluted gallon?a. $2.25

    b. $2.00c. $1.75d. $1.50

    e. None of the above

    1.

    2.

    3.

    4.

    5.

    6.

  • 8/10/2019 Detailing Manual

    45/5244

    If a product is diluted 1:15 and costs $24 per gallon, what is the cost per diluted gallon?

    a. $2.25b. $2.00

    c. $1.75d. $1.50e. None of the above

    Silicones are not recommended for use in a body shop environment:

    T

    F

    3M Detail Polish 108 cuts more than 3M Detail Compound 308:

    T

    F

    The recommended product for removing tar from a painted surface is:

    a. 3M Heavy Duty Wheel Cleaner diluted 1:2 (Do not use on glass, engines, anodized wheels and/or

    wheels with no coating or with coating cracked or in poor condition.)

    b. 3M All Purpose Cleaner & Degreaser diluted 1:15

    c. 3M Heavy Duty Wheel Cleaner undiluted (Do not use on glass, engines, anodized wheels and/orwheels with no coating or with coating cracked or in poor condition.)

    d. 3M All Purpose Cleaner & Degreaser diluted 1:30

    e. None of the above

    The recommended product for removing bug spatters is:a. 3M Heavy Duty Wheel Cleaner diluted 1:2 (Do not use on glass, engines, anodized wheels and/or

    wheels with no coating or with coating cracked or in poor condition.)

    b. 3M All Purpose Cleaner & Degreaser diluted 1:15

    c. 3M Heavy Duty Wheel Cleaner undiluted (Do not use on glass, engines, anodized wheels and/orwheels with no coating or with coating cracked or in poor condition.)

    d. 3M All Purpose Cleaner & Degreaser diluted 1:30

    e. None of the above

    When detailing a vehicle, it is recommended to begin washing it from the bottom because that is the dirtiest part:

    T

    F

    The polishes and compounds can or may be used with wool pads: T

    F

    There is no difference between 3M Heavy Duty Wheel Cleaner and competitive wheel cleaners:

    T

    F

    Trizact Abrasive Discs must always be used damp:

    T

    F

    7.

    8.

    9.

    10.

    11.

    12.

    13.

    14.

    15.

    ANSWERS:1.d2.c3.b4.b5.a6.b7.d

    8.T9.F10.e11.b12.F13.T14.F15.T

  • 8/10/2019 Detailing Manual

    46/5245

    Ordering Information

    Exterior Cleaners

    38350 | 3M All Purpose Cleaner & Degreaser (38050)* | Gallon | 4

    38351 | 3M All Purpose Cleaner & Degreaser (38051)* | 5-Gallon Pail | 1

    38052 | 3M All Purpose Cleaner & Degreaser | 55-Gallon Drum | 1

    38070 | 3M Perfect-It III Cleaner Clay | 1 Jar | 638374 | 3M Heavy Duty Wheel Cleaner (38074)* | Gallon | 4

    38375 | 3M Heavy Duty Wheel Cleaner (38075)* | 5-Gallon Pail | 1

    38076 | 3M Heavy Duty Wheel Cleaner | 55-Gallon Drum | 1

    38377 | 3M Car Wash Soap (38077)* | Gallon | 4

    38378 | 3M Car Wash Soap (38078)* | 5-Gallon Pail | 1

    38079 | 3M Car Wash Soap | 55-Gallon Drum | 1

    Part | Product | Container | Cont.No. | Name | Size | Per Case

    Exterior Cleaners (Solvents)

    38080 | 3M Adhesive Remover | Gallon | 4

    38081 | 3M Adhesive Remover | 5-Gallon Pail | 1

    38082 | 3M Adhesive Remover | 55-Gallon Drum | 1

    Part | Product | Container | Cont.

    No. | Name | Size | Per Case

    Exterior Dressings

    38124 | 3M Engine and Tire Dressing | Gallon | 4

    38125 | 3M Engine and Tire Dressing | 5-Gallon Pail | 1

    38126 | 3M Engine and Tire Dressing | 55-Gallon Drum | 1

    38127 | 3M Tire Dressing | Gallon | 4

    38128 | 3M Tire Dressing | 5-Gallon Pail | 1

    38129 | 3M Tire Dressing | 55-Gallon Drum | 1

    38327 | 3M Silicone Free Tire Dressing (38227)* | Gallon | 4

    38328 | 3M Silicone Free Tire Dressing (38228)* | 5-Gallon Pail | 1

    Part | Product | Container | Cont.No. | Name | Size | Per Case

    O

    RDERINGINFORMATION

    * Part number to be discontinued

  • 8/10/2019 Detailing Manual

    47/52

    Interior Cleaners

    Part | Product | Container | Cont.No. | Name | Size | Per Case

    Waxes, Polishes & Compounds

    Part | Product | Container | Cont.No. | Name | Size | Per Case

    Detailing Accessories

    37721 | 3M Detailing Product Diluter | 1 Diluter | 1

    37712 | 3M Detailing Diluter Single Product | 1 Diluter | 1

    37716 | 3M Detailing Spray Bottle | 1 Bottle | 24

    37717 | 3M Detailing GP Spray Nozzle | 1 Spray Head | 24

    37718 | 3M Detailing Solvent Spray Nozzle | 1 Spray Head | 24

    37720 | 3M Detailing Squeeze Bottle | 1 Bottle & Top | 24

    Part | Product | Container | Cont.No. | Name | Size | Per Case

    46

    38350 | 3M All Purpose Cleaner & Degreaser (38050)* | Gallon | 4

    38351 | 3M All Purpose Cleaner & Degreaser (38051)* | 5-Gallon Pail | 1

    38052 | 3M All Purpose Cleaner & Degreaser | 55-Gallon Drum | 1

    38095 | 3M Extraction Cleaner* (See 38350) | Gallon | 4

    38399 | 3M Glass Cleaner (38099)* | Gallon | 4

    38300 | 3M Glass Cleaner (38100)* | 5-Gallon Pail | 1

    38101 | 3M Glass Cleaner | 55-Gallon Drum | 1

    38221 | 3M Premium Glass Cleaner | Gallon | 4

    38222 | 3M Premium Glass Cleaner | 5-Gallon Pail | 1

    Interior Dressing

    38086 | 3M Interior Dressing | Gallon | 4

    38087 | 3M Interior Dressing | 5-Gallon Pail | 1

    Part | Product | Container | Cont.

    No. | Name | Size | Per Case

    Note: For Diluter Service Parts, contact Shopware, Inc. 1-800-877-9344

    38105 | 3M Detail Compound #308 | Gallon | 4

    38111 | 3M Detail Wax | Gallon | 4

    38113 | 3M Perfect-It Gloss Enhancer | Gallon | 4

    38114 | 3M Perfect-It Gloss Enhancer | 5-Gallon Pail | 138115 | 3M Perfect-It Gloss Enhancer | 55-Gallon Drum | 1

    38116 | 3M Detail Polish #208 | Gallon | 4

    38133 | 3M Detail Polish #108 | Gallon | 4

    38112 | 3M Performance Finish | Quart | 6

    39030 | 3M Performance Finish | Pint | 6

    * Part number to be discontinued

  • 8/10/2019 Detailing Manual

    48/5247

    O

    RDERINGINFORMATION

    Sanding

    00850 | 3M Hookit II Finishing Film | P1500 | 50 | 4

    00868 | 3M Hookit II Finishing Film | P1200 | 50 | 4

    02023 | 3M Imperial Wetordry Paper Sheets | Micro Fine 1500 | 50 | 5

    02044 | 3M Imperial Wetordry Paper Sheets | Micro Fine 2000 | 50 | 502045 | 3M Imperial Wetordry Paper Sheets | Micro Fine 2500 | 50 | 5

    02075 | 3M Trizact Hookit II Foam Disc 6 | P3000 | 15 | 4

    05274 | 3M Hookit II Soft Interface Pad | Pad | 6 Pad | 10

    05251 | 3M Hookit II Disc Pad | Painters Pad | 6 Pad | 10

    05291 | 3M Hookit II Hand Pad 6 | Pad | 6 Pad | 10

    Part | Product | Grade | Sheets or | QuantityNo. | Name | | Pads/Box | Per Case

    Compounding Pads

    Part | Product | Items | Quantity

    No. | Name | Per Unit | Per Case

    Ordering Information(CONTINUED)

    05703 | 3M Superbuff III Buffing Pad | Pad | 6

    05704 | 3M Superbuff III 2 Plus 2 Buffing Pad | Pad | 6

    05710 | 3M Superbuff adapter | adapter | 10

    05717 | 3M Hookit SBS Backup Pad | Pad | 1

    05718 | 3M Perfect-It Backup Pad | Pad | 1

    05719 | 3M Perfect-It III Compounding Pad | Pad | 24

    05723 | 3M Perfect-It Foam Compounding Pad | 2 Pads/Bag | 12

    05737 | 3M Perfect-It Plus Foam Compounding Pad | 1 Pad/Bag | 6

  • 8/10/2019 Detailing Manual

    49/5248

    Polishing Pads

    Part | Product | Items | QuantityNo. | Name | Per Unit | Per Case

    Detail Cloths

    06016 | 3M Perfect-It Detail Cloths | 6 Cloths/Bag | 6

    06017 | 3M Perfect-It Detail Cloths Bulk | 50 Cloths/Bag | 1

    06018 | 3M Perfect-It Jumbo Detail Cloths | 6 Cloths/Bag | 6

    Part | Product | Items | QuantityNo. | Name | Per Unit | Per Case

    05717 | 3M Hookit SBS Backup Pad | Pad | 1

    05718 | 3M Perfect-It Backup Pad | Pad | 1

    05733 | 3M Perfect-It Plus Ultrafina Foam Polishing Pad - 8 I 1 Pad/Bag | 6

    05751 | 3M Perfect-It Ultrafina Foam Polishing Pad - 8 I 2 Pads/Bag | 605725 | 3M Perfect-It Foam Polishing Pad | 2 Pads/Bag | 6

    05729 | 3M Perfect-It Foam Polishing D/A Pad - 6 | 2 Pads/Bag | 12

    05739 | 3M Perfect-It Hookit II Foam D/A Glazing Pad | 2 Pads/Bag | 12

    05732 | 3M Perfect-It Hookit II DA Foam Application Pad - 6 I 2 Pads/Bag | 12

    05738 | 3M Perfect-It Plus Foam Polishing Pad | Pad | 6

  • 8/10/2019 Detailing Manual

    50/5249

    O

    RDERINGINFORMATION

    Spray Bottle Labels

    60- | Product | Labels Per Pack*Number | Name

    Ordering Information(CONTINUED)

    60-4400-7328-0 | 3M Heavy Duty Wheel Cleaner | 25

    60-4400-7329-8 | 3M Heavy Duty Wheel Cleaner/Concentrate | 25

    60-4400-9926-9 | 3M All Purpose Cleaner and Degreaser HD 1:15 | 25

    60-4400-9925-1 | 3M All Purpose Cleaner and Degreaser LD 1:30 | 2560-4400-7339-7 | 3M Glass Cleaner | 25

    60-4400-7576-4 | 3M Premium Glass Cleaner | 25

    60-4400-7346-2 | 3M Car Wash Soap | 25

    60-4400-7341-3 | 3M Adhesive Remover | 25

    60-4400-7331-4 | 3M Interior Dressing | 25

    60-4400-7343-9 | 3M Engine and Tire Dressing | 25

    60-4400-7340-5 | 3M Tire Dressing | 25

    60-4400-8404-8 | 3M Silicone Free Tire Dressing | 25

    60-4400-7344-7 | 3M Detail Polish #108 | 25

    60-4400-7332-2 | 3M Detail Polish #208 | 25

    60-4400-7614-3 | 3M Detail Polish #308 | 2560-4400-7345-4 | 3M Detail Wax | 25

    60-4400-7342-1 | 3M Gloss Enhancer | 25

    *Please Order Per Pack

    Contact a 3M sales representative for more information:

    3M Automotive Aftermarket Division3M Center, Bldg. 223-6N-01

    St. Paul, MN 55144-1000Telephone: 1-877-MMM-CARS (1-877-666-2277)

    or (651) 737-6501

  • 8/10/2019 Detailing Manual

    51/5250

  • 8/10/2019 Detailing Manual

    52/52