Detail Booklet StoTherm ci over Masonry - Sto Corp. · Detail No.: 19.01b Date: February 2019...
Transcript of Detail Booklet StoTherm ci over Masonry - Sto Corp. · Detail No.: 19.01b Date: February 2019...
Detail BookletStoTherm®ci over MasonrySeries 19.xxMasonry Frame ConstructionFebruary 2019
®
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, of for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.comProperty of Sto Corp.All Rights Reserved.
3800 Camp Creek Pkwy. SWBldg. 1400 • Suite 120Atlanta, GA 30331Tel: (800) 221-2397Fax: (404) 346-3119helpdesk.stocorp.com
Sto Corp.
StoTherm® ci Over Masonry
System ComonentsDetail No.: 19.00Date: February 2019
Mansory Substrate
StoGuard®
Sto Adhesive
Sto Insulation Board
Sto Mesh
Sto Base Coat
Sto Finish
Pre-wrapped or back wrapped Sto Insulation Board
Notes:
Detail shows the components of StoTherm® ciContinuous Insulation System:
1) StoGuard® Waterproof Air Barrier (2 coats minimum) 2) Sto Adhesive
3) Sto Insulation Board
4) Sto Base Coat
5) Sto Mesh
6) Sto Finish
®
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, of for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
IMPORTANT: Components not identified as Sto are furnished by other manufactur-ers and are not necessarily installed by trades who install the Sto products. Refer to project specific contract documents.
www.stocorp.com
Property of Sto Corp. All Rights Reserved.
StoTherm® ci Over Masonry
Termination at GradeDetail No.: 19.01aDate: February 2019
Mansory Substrate
Sto Adhesive
Sto Insulation Board
Sto Base Coat and Mesh
Sto Finish
StoGuard® Waterproof Air Barrier (2 coats minimum)
Pre-wrapped or back wrapped Sto Insulation Board
Maintain min. 6 inches (152mm) above finished grade.
Protective Coating
Cementitious Damp-proofing or Water- proofing as needed
Notes:
1) Provide minimum 6 inches (152 mm) clearance between StoTherm® ci termination and finished grade. Increase distance above grade for snow regions.
2) Provide cementitious damp proofing or waterproofing as needed below grade and on exposed masonry above grade. Counter flash StoTherm® ci over damp- proofing/waterproofing. WhereStoTherm® ci is installed over non-cementi- tious dampproofing/ waterproofing verify compatibility of StoTherm® ci components.
3) Provide adequate slope of finished grade away from structure for drainage.
®
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, of for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
IMPORTANT: Components not identified as Sto are furnished by other manufactur-ers and are not necessarily installed by trades who install the Sto products. Refer to project specific contract documents.
www.stocorp.com
Property of Sto Corp. All Rights Reserved.
StoTherm® ci Over Masonry
Termination at Sidewalk with Expansion JointDetail No.: 19.01bDate: February 2019
Masonry Substrate
Sto Adhesive
Sto Insulation Board
Sto Base Coat and Mesh
Sto Finish
StoGuard®
Waterproof Air Barrier (2 coats minimum)
Pre-wrapped or back wrapped Sto Insulation Board
Backer Rod and Sealant
Cementitious Damp-proofing or Water- proofing as needed
Notes:
1) Detail is intended for areas of construction protected from weather - covered walk ways, balconies or decks under cover, or areas protected with large projecting eaves or soffit overhangs. Refer to Sto Detail 19.01a for weather exposed areas.
2) Provide cementitious damp proofing or waterproofing as needed below grade and on exposed masonry above grade. Counter flash StoTherm® ci over damp- proofing/waterproofing. WhereStoTherm® ci is installed over non-cementi- tious dampproofing/ waterproofing verify compatibility of StoTherm® ci components.
3) Provide adequate slope of finished grade away from structure for drainage.
®
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, of for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
IMPORTANT: Components not identified as Sto are furnished by other manufactur-ers and are not necessarily installed by trades who install the Sto products. Refer to project specific contract documents.
www.stocorp.com
Property of Sto Corp. All Rights Reserved.
Mansory Substrate
StoGuard® RapidSeal™
StoGuard® Waterproof Air Barrier (2 coats minimum)
StoTherm® ci Over Masonry
Window Head/Jamb: Rough Opening ProtectionDetail No.: 19.24a1Date: February 2019
Notes:
1) Protect masonry with StoGuard® RapidSeal™. Fold up minimum 2 inches (51mm) at head and at ends onto face of masonry.
2) Refer to Sto detail 19.24a2 for window installation and Sto detail 19.24a3 for complete assembly.
3) Test the final assembly using materials and sub-trades associated with the project to verify performance.
®
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, of for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
IMPORTANT: Components not identified as Sto are furnished by other manufactur-ers and are not necessarily installed by trades who install the Sto products. Refer to project specific contract documents.
www.stocorp.com
Property of Sto Corp. All Rights Reserved.
Mansory Substrate
StoGuard® Waterproof Air Barrier (2 coats minimum)
StoGuard® RapidSeal™
1/2"(13 mm) gap forperimeter air seal
StoGuard® RapidSeal™
1/2"(13 mm) gap for perimeter weather seal
StoTherm® ci Over Masonry
Window Head/Jamb: Window InstalledDetail No.: 19.24a2Date: February 2019
Notes:
1) Provide gap for continuous exterior perimeter weather seal.
2) Provide gap for continuous interior perimeter air seal.
3) Consult with window and sealant manufacturers to verify installation detailing.
4) Refer to Sto detail 19.24a1 for rough opening protec- tion and Sto detail 19.24a3 for complete assembly.
5) Test the final assembly using materials and sub-trades associated with the project to verify performance.
®
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, of for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
IMPORTANT: Components not identified as Sto are furnished by other manufactur-ers and are not necessarily installed by trades who install the Sto products. Refer to project specific contract documents.
www.stocorp.com
Property of Sto Corp. All Rights Reserved.
Sto Finish
StoGuard® Waterproof Air Barrier (2 coats minimum)
Sto Insulation Board
Sto Base Coat with Sto Mesh embedded
Pre-wrapped or back wrapped Sto Insulation Board
Mansory Substrate
StoGuard® RapidSeal™
Backer rod and sealant (continuous perimeter air seal).
Gap (1/4"-1/2") for drainage. Seal with backer rod and sealant. Provide weeps approxi-mately 3 inches (76mm) from corner and16 inches (406mm) O.C.
Backer rod and sealant (continuous perimeter weather seal).
Mechanical fastener (required only at return where StoTherm® ci is installed over StoGuard® RapidSeal™).
StoTherm® ci Over Masonry
Window Head/Jamb: StoTherm® ci Return and Perimeter SealsDetail No.: 19.24a3Date: February 2019
Notes:
1) Provide continuous exterior perimeter weather seal.
2) Provide continuous interior perimeter air seal.
3) Consult with window and sealant manufacturer to verify installation detailing.
4) Refer to Sto detail 19.24a1 for rough opening protec tion and Sto detail 19.24a2 for window installation.
5) Test the final assembly using materials and sub-trades associated with the project to verify performance.
®
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, of for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
IMPORTANT: Components not identified as Sto are furnished by other manufactur-ers and are not necessarily installed by trades who install the Sto products. Refer to project specific contract documents.
www.stocorp.com
Property of Sto Corp. All Rights Reserved.
Mansory Substrate
StoGuard® RapidSea™l(for slope)
StoGuard® RapidSeal™
Pre-fabricated Pan Flashing
StoGuard® RapidSeal™
StoGuard®
Waterproof Air Barrier (2 coats minimum)
StoTherm® ci Over Masonry
Window Sill: Rough Opening Protection and Pan Flashing at Sill
Detail No.: 19.26a1Date: February 2019
Notes:
1) Protect masonry sill with StoGuard® RapidSeal™. Fold up minimum 4 inches (102mm) at jamb. Fold down 2 inches (51mm) at sill and at ends onto face of masonry.
2) Install StoGuard® Rapid- Seal™ strip at back of opening to create slope and fold up nailer.
3) Secure pre-fabricated pan flashing by others into place.
4) Provide pan flashing with thermal break in cold climate zones.
5) Refer to Detail 19.26a2 for protection at jamb and Sto details 19.24a1 and 19.24a2 for protection at head. Refer to Sto detail 19.26a3 for complete sill / jamb assembly.
®
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, of for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
IMPORTANT: Components not identified as Sto are furnished by other manufactur-ers and are not necessarily installed by trades who install the Sto products. Refer to project specific contract documents.
www.stocorp.com
Property of Sto Corp. All Rights Reserved.
Mansory Substrate
Window Frame
StoGuard® RapidSeal™(for slope)
StoGuard® RapidSeal™
Pre-fabricated Pan Flashing
StoGuard® RapidSeal™
StoGuard®
Waterproof Air Barrier (2 coats minimum)
StoTherm® ci Over Masonry
Window Sill/Jamb: Rough Opening Protection and Pan Flashing with Window Installed
Detail No.: 19.26a2Date: February 2019
Notes:
1) Provide gap for continuous exterior perimeter weather seal.
2) Provide gap for continuous interior perimeter air seal. 3) Consult with window and sealant manufacturers to verify installation detailing.
4) See Sto detail 19.26a1 for rough opening protection and pan flashing at sill. See Sto detail 19.24a1 and 19.24a2 for protection at head. See Sto detail 19.26a3 for complete sill/jamb assembly.
5) Test the final assembly using materials and sub-trades associated with the project to verify performance.
®
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, of for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
IMPORTANT: Components not identified as Sto are furnished by other manufactur-ers and are not necessarily installed by trades who install the Sto products. Refer to project specific contract documents.
www.stocorp.com
Property of Sto Corp. All Rights Reserved.
StoGuard® RapidSeal™
Masonry Substrate
StoGuard® Waterproof Air Barrier (2 coats minimum)
Sto Insulation Board
Sto Base Coat with Sto Mesh embedded
Sto Finish
Mechanical fastener (required only at return where StoTherm® ci isinstalled over StoGuard® RapidSeal™).
Backer rod and sealant (continuous perimeter weather seal).
Backer rod and Sealant with weeps
Backer rod and sealant (continuous perimeter air seal).
Back wrapped or pre-wrapped Sto Insulation Board
Sealant
StoTherm® ci Over Masonry
Window Sill/Jamb: Window Installed withStoTherm® ci Return and Perimeter Seals
Detail No.: 19.26a3Date: February 2019
Notes:
1) Provide gap for continuous exterior perimeter weather seal.
2) Provide gap for continuous interior perimeter air seal.
3) Consult with window and sealant manufacturer to verify installation detailing.
4) See Sto detail 19.26a1 and 19.26a2 for rough opening protection and pan flashing at sill. See Sto details 19.24a1 and 19.24a2 for protection at head and 19.24a3 for complete head / jamb assembly. 5) Test the final assembly using material and sub-trades associated with the project to verify performance.
®
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, of for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
IMPORTANT: Components not identified as Sto are furnished by other manufactur-ers and are not necessarily installed by trades who install the Sto products. Refer to project specific contract documents.
www.stocorp.com
Property of Sto Corp. All Rights Reserved.
StoTherm® ci Over Masonry
Floor Line with JointDetail No.: 19.41Date: February 2019
Floor Slab
Masonry Substrate
Sto Adhesive
Pre-wrapped or back wrapped Sto Insulation Board
Backer rod and Sealant
StoGuard® Transition Membrane
Sto Finish
Sto Base Coat and Mesh
Sto Insulation Board
StoGuard® Waterproof Air Barrier (2 coats minimum)
Notes:
1) Provide joint at floor line to coincide with line where masonry adjoins under side of concrete floor slab.
2) Back joint with StoGuard® Transition Membrane.
®
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, of for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
IMPORTANT: Components not identified as Sto are furnished by other manufactur-ers and are not necessarily installed by trades who install the Sto products. Refer to project specific contract documents.
www.stocorp.com
Property of Sto Corp. All Rights Reserved.
StoTherm® ci Over Masonry
Horizontal Joint at Dissimilar MaterialDetail No.: 19.42Date: February 2019
Floor Slab
Masonry Substrate
Sto Adhesive
Sto Finish
StoGuard® Waterproof Air Barrier (2 coats minimum)
Sto Insulation Board
StoGuard® RapidSeal™
Sto Base Coat and Mesh
Flashing
Pre-wrapped or back wrapped Sto Insulation Board
StoGuard® Transition Membrane
Alternate cladding assembly
Notes:
1) Provide flashing minimum 4 inches (100mm) behind StoTherm® ci and project flashing with drip edge beyond face of alternate cladding below.
2) Determine installation sequence in advance of construction.
®
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, of for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
IMPORTANT: Components not identified as Sto are furnished by other manufactur-ers and are not necessarily installed by trades who install the Sto products. Refer to project specific contract documents.
www.stocorp.com
Property of Sto Corp. All Rights Reserved.
StoTherm® ci Over Masonry
Vertical Joint at Dissimilar MaterialDetail No.: 19.50Date: February 2019
StoGuard® Waterproof Air Barrier (2 coats minimum)
Masonry Substrate
Sto Adhesive
Sto Insulation Board
Pre-wrapped or back wrapped Sto Insulation Board
Sto Base Coat and Mesh
StoGuard® Transition Membrane
Backer rod with sealant
Sto Finish
StoGuard® Waterproof Air Barrier (2 coats minimum)
Alternate cladding assembly
Notes:
1) Determine installation sequence in advance of construction. Coordinate subtrades to ensure the proper installation of materials.
2) StoGuard® Transition Membrane isolates the potentially wet environment behind the alternate cladding from StoTherm® ci.
3) Provide minimum 3/4" (20mm) joint between the StoTherm® ci and the alternate cladding. Provide drainage for the joint assembly.
®
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, of for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
IMPORTANT: Components not identified as Sto are furnished by other manufactur-ers and are not necessarily installed by trades who install the Sto products. Refer to project specific contract documents.
www.stocorp.com
Property of Sto Corp. All Rights Reserved.
Masonry Substrate
StoTherm® ci Over Masonry
Vertical Expansion JointDetail No.: 19.51Date: February 2019
StoGuard® Air and Moisture Barrier
Sto EPS Insulation Board(Pre-wrapped or back wrapped)
Sto Base Coat and Mesh
Notes:
1) Provide minimum 3/4" (20mm) joint.
2) Refer to StoTherm ci System Bulletins and Specifications, Sto Product Bulletins, Tech Hotlines, and Sto Installation and Maint- nance Guides for complete information.
3) Refer to applicable ICC or CCMC Evaluation Report for building code compliance information.
Sto Adhesive
Sto Finish
Sealant and Backer Rod
Sto Primer(optional)
Backer Rod(To support Sto Transition Membrane
but not restrict its movement)
StoGuard® Transition Membrane(Embedded in StoGuard® Air and
Moisture Barrier)
®
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, of for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
IMPORTANT: Components not identified as Sto are furnished by other manufactur-ers and are not necessarily installed by trades who install the Sto products. Refer to project specific contract documents.
www.stocorp.com
Property of Sto Corp. All Rights Reserved.
Masonry Substrate
Sto Adhesive
Sto base Coat and Mesh
Pre-wrapped or back wrapped Sto Insulation Board
Metal Flashing
Roof Membrane
Roof Sheathing
Sto Finish
Sto Insulation Board
StoGuard® Waterproof Air Barrier (2 coats minimum)
StoTherm® ci assembly over fabricated metal support structure and sheathing.
Backer rod with sealant
StoTherm® ci Over Masonry
Termination at Built-Out FeatureDetail No.: 19.53Date: February 2019
Notes:
1) Terminate StoTherm® ci minimum 2 inches (51mm) above metal flashing with minimum 2 inch (51mm) overlap of flashing.
2) Provide sealant beneath flashing drip edge.
®
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, of for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
IMPORTANT: Components not identified as Sto are furnished by other manufactur-ers and are not necessarily installed by trades who install the Sto products. Refer to project specific contract documents.
www.stocorp.com
Property of Sto Corp. All Rights Reserved.
StoTherm® ci Over Masonry
Termination at Flat Roof with Gravel StopDetail No.: 19.60aDate: February 2019
Gravel Stop(min. 2-1/2"[64mm] overlap of StoTherm® ci termination)
Roof Membrane
Backer rod with sealant
Pre-wrapped or back wrapped Sto Insulation Board
StoGuard® Waterproof Air Barrier (2 coats minimum)
Sto Finish
Sto Base Coat and Mesh
Sto Insulation Board
Masonry Substrate
Notes:
1) Provide continuity of roofing membrane with StoTherm® ci for air tight and water tight condition beneath gravel stop. Verify compatibility of materials where they overlap or interface.
2) Provide minimum 2-1/2 inch (64mm) overlap of gravel stop over terminating edge of StoTherm® ci for single story construction. Increase overlap with building height.
®
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, of for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
IMPORTANT: Components not identified as Sto are furnished by other manufactur-ers and are not necessarily installed by trades who install the Sto products. Refer to project specific contract documents.
www.stocorp.com
Property of Sto Corp. All Rights Reserved.
StoTherm® ci Over Masonry
Termination at Parapet CapDetail No.: 19.60bDate: February 2019
Masonry Substrate
Roof Membrane
Sealant
Pre-wrapped or back wrappedSto Insulation Board
Sto Adhesive
Sto Finish
Sto Base Coat and Mesh
Sto Insulation Board
StoGuard® Waterproof Air Barrier (2 coats minimum)
Notes:
1) Provide continuity of roof membrane along back of parapet with base coat for air barrier continui- ty and verify compatibility of roof membrane if in contact with base coat.
2) Completely insulate back side of parapet if necessary to prevent condensation within parapet based on climate conditions.
3) Provide minimum 2.5 inch (65mm) overlap of parapet coping over face of StoTherm® ci. Increase overlap with building height.
®
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, of for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
IMPORTANT: Components not identified as Sto are furnished by other manufactur-ers and are not necessarily installed by trades who install the Sto products. Refer to project specific contract documents.
www.stocorp.com
Property of Sto Corp. All Rights Reserved.
StoTherm® ci Over Masonry
Termination at EaveDetail No.: 19.63Date: February 2019
Roof Assembly
Masonry Substrate
Backer rod and Sealant
Pre-wrapped or back wrappedSto Insulation Board
Sto Adhesive
Sto Finish
Sto Base Coat and Mesh
Sto Insulation Board
StoGuard® Waterproof Air Barrier (2 coats minimum)
Notes:
1) Install soffit board prior to installation StoTherm® ci to provide bearing surface for sealant and backer rod.
2) Provide air tight connection with roof / eave air barrier material with StoGuard®.
®
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, of for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
IMPORTANT: Components not identified as Sto are furnished by other manufactur-ers and are not necessarily installed by trades who install the Sto products. Refer to project specific contract documents.
www.stocorp.com
Property of Sto Corp. All Rights Reserved.
StoTherm® ci Over Masonry
Termination at Fixture Penetration through StoTherm® ci
Detail No.: 19.73Date: February 2019
Masonry Substrate
StoGuard® Waterproof Air Barrier (2 coats minimum)
Sto Adhesive
Back-wrap Termination
Wood Blocking with spray foam around perimeter
Backer rod with Sealant
Light Fixture
Sto Finish
Sto Base Coat and Mesh
Sto Insulation Board
Notes:
1) For some penetrations a fillet bead of sealant over bond breaker around perimeter of penetration may also be acceptable. Consult with sealant manufacturer.
®
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, of for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
IMPORTANT: Components not identified as Sto are furnished by other manufactur-ers and are not necessarily installed by trades who install the Sto products. Refer to project specific contract documents.
www.stocorp.com
Property of Sto Corp. All Rights Reserved.
StoTherm® ci Over Masonry
Surface Mount Fixture Attachment Through StoTherm® ciDetail No.: 19.74Date: February 2019
Sto AdhesiveSto Insulation BoardPVC Sleeve lined with SealantSto Base Coat and MeshSto FinishGutter StrapWasher bedded in SealantFastener
Masonry Substrate
Sto Adhesive
Sto Insulation Board
Sto Base Coat and Mesh
Sto Finish
Pre-wrapped or back wrapped Sto Insulation Board
Cementitious Damp-proofing or Water- proofing as needed
Notes:
1) Provide minimum 6 inches (152 mm) clearance between StoTherm® ci termination and finished grade. Increase distance above grade for snow regions.
2) Provide cementitious damp proofing or waterproofing as needed below grade and on exposed masonry above grade. Counter flash StoTherm® ci over damp- proofing/waterproofing. Where StoTherm® ci and non-cementitious damp- proofing/waterproofing meet, verify compatibility of StoTherm® ci components.
3) Provide adequate slope of finished grade away from structure for drainage.
Sto Guard® Waterproof Air Barrier (2 coats minimum)
®
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, of for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
IMPORTANT: Components not identified as Sto are furnished by other manufactur-ers and are not necessarily installed by trades who install the Sto products. Refer to project specific contract documents.
www.stocorp.com
Property of Sto Corp. All Rights Reserved.
StoTherm® ci Over Masonry
Termination at Scupper PenetrationDetail No.: 19.75Date: February 2019
Masonry Substrate
StoGuard® Waterproof Air Barrier (2 coats minimum)
Back-wrap Termination
Waterproof membrane
Backer rod with Sealant entire perimeter
Scupper Assembly
Sto Finish
Sto Base Coat and Mesh
Sto Insulation Board
Roof or deck assembly
Notes:
1) Provide leakproof scupper assembly and installation to direct water away from the wall surface.
®
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, of for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
IMPORTANT: Components not identified as Sto are furnished by other manufactur-ers and are not necessarily installed by trades who install the Sto products. Refer to project specific contract documents.
www.stocorp.com
Property of Sto Corp. All Rights Reserved.
StoTherm® ci Over Masonry
Termination at Pipe PenetrationDetail No.: 19.76Date: February 2019
Masonry Substrate
StoGuard® Waterproof Air Barrier (2 coats minimum)
Sto Adhesive
Spray foam around perimeter of penetrating element.
Backer rod with Sealant entire perimeter
Pipe Penetration
Back-wrap Termination
Sto Finish
Sto Base Coat and Mesh
Sto Insulation Board
Notes:
1) For some penetrations a fillet bead of sealant over bond breaker around perimeter of penetration may also be acceptable. Consult with sealant manufacturer.
®
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, of for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
IMPORTANT: Components not identified as Sto are furnished by other manufactur-ers and are not necessarily installed by trades who install the Sto products. Refer to project specific contract documents.
www.stocorp.com
Property of Sto Corp. All Rights Reserved.