Design for Manufacturing and Assembly
Transcript of Design for Manufacturing and Assembly
Ken Youssefi UC Berkeley 1
Design for Manufacturing and Assembly
• Design for manufacturing (DFM) is design based on minimizing the cost of production and/or time to market for a product, while maintaining an appropriate level of quality. A primary strategy in DFM involves minimizing the number of parts in a product.
• Design For Assembly (DFA) involves making attachment directions and methods simpler.
Ken Youssefi UC Berkeley 2
DFM and DFA BenefitsIt reduces part count thereby reducing cost. If a
design is easier to produce and assemble, it can be done in less time, so it is less expensive. Design for manufacturing and assembly should be used for that reason if no other.
It increases reliability, because if the production process is simplified, then there is less opportunity for errors.
It generally increases the quality of the product for the same reason as why it increases the reliability.
Ken Youssefi UC Berkeley 3
DFM and DFA• DFM and DFA starts with the formation of the
design team which tends to be multi-disciplinary, including engineers, manufacturing managers, cost accountants, and marketing and sales professionals.
• The most basic approach to design for manufacturing and assembly is to apply design guidelines.
• You should use design guidelines with an understanding of design goals. Make sure that the application of a guideline improves the design concept on those goal.
Ken Youssefi UC Berkeley 4
DFM and DFA Design Guidelines• Minimize part count by incorporating multiple functions into
single parts. Several parts could be fabricated by using different manufacturing processes (sheet metal forming, injection molding). Ask yourself if a part function can be performed by a neighboring part.
Ken Youssefi UC Berkeley 5
DFM and DFA Design Guidelines
• Modularize multiple parts into single sub-assemblies.
Ken Youssefi UC Berkeley 6
DFM and DFA Design Guidelines
• Design to allow assembly in open spaces, not confined spaces. Do not bury important components.
Ken Youssefi UC Berkeley 7
DFM and DFA Design Guidelines• Parts should easily indicate orientation for insertion.
Parts should have self-locking features so that the precise alignment during assembly is not required. Or, provide marks (indentation) to make orientation easier.
Ken Youssefi UC Berkeley 8
DFM and DFA Design Guidelines• Standardize parts to reduce variety.
Ken Youssefi UC Berkeley 9
DFM and DFA Design Guidelines• Design parts so they do not tangle or stick to each
other.
Ken Youssefi UC Berkeley 10
DFM and DFA Design Guidelines
• Distinguish different parts that are shaped similarly by non-geometric means, such as color coding.
Ken Youssefi UC Berkeley 11
DFM and DFA Design Guidelines• Design parts to prevent nesting. Nesting is when
parts are stacked on top of one another clamp to one another, for example, cups and coffee lids
Ken Youssefi UC Berkeley 12
DFM and DFA Design Guidelines• Design parts with orienting features to make
alignment easier.
Ken Youssefi UC Berkeley 13
DFM and DFA Design Guidelines
• Provide alignment features on the assembly so parts are easily oriented.
Ken Youssefi UC Berkeley 14
DFM and DFA Design Guidelines• Design the mating parts for easy insertion. Provide
allowance on each part to compensate for variation in part dimensions.
Ken Youssefi UC Berkeley 15
DFM and DFA Design Guidelines• Design the first part large and wide to be stable
and then assemble the smaller parts on top of it sequentially.
Ken Youssefi UC Berkeley 16
DFM and DFA Design Guidelines• If you cannot assemble parts from the top down
exclusively, then minimize the number of insertion direction. Never require the assembly to be turned over.
Ken Youssefi UC Berkeley 17
DFM and DFA Design Guidelines• Joining parts can be done with fasteners (screws,
nuts and bolts, rivets), snap fits, welds or adhesives.
Ken Youssefi UC Berkeley 18
DFM and DFA Design Guidelines
Ken Youssefi UC Berkeley 19
Minimizing the Number of PartsTo determine whether it is possible to combine neighboring parts, ask yourself the following questions:
• Must the parts move relative to each other?• Must the parts be electrically or thermally
insulated?• Must the parts be made of different material?• Does combing the parts interfere with
assembly of other parts?• Will servicing be adversely affected?
If the answer to all questions is “NO”, you should find a way to combine the parts.
Ken Youssefi UC Berkeley 20
Minimizing the Number of PartsThe concept of the theoretical minimum number of
parts was originally proposed by Boothroyd (1982). During the assembly of the product, generally a part is required only when;
1. A kinematic motion of the part is required.
2. A different material is required.
3. Assembly of other parts would otherwise be prevented.
If non of these statements are true, then the part is not needed to be a separate entity.
KISS – Keep It Simple Stupid
Ken Youssefi UC Berkeley 21
DFM Design Guidelines
Another aspect of design for manufacturing is to make each part easy to produce.
The up to date DFM guidelines for different processes should be obtained from production engineer knowledgeable about the process. The manufacturing processes are constantly refined.
Ken Youssefi UC Berkeley 22
DFM Design GuidelinesInjection Molding
Injection MoldingFabrication of Plastics
Ken Youssefi UC Berkeley 23
DFM Design GuidelinesInjection Molding
Minimize section thickness, cooling time is proportional to the square of the thickness, reduce cost by reducing the cooling time.
Provide adequate draft angle for easier mold removal.
Ken Youssefi UC Berkeley 24
DFM Design GuidelinesInjection Molding
Keep rib thickness less than 60% of the part thickness in order to prevent voids and sinks.
Avoid sharp corners, they produce high stress and obstruct material flow.
Ken Youssefi UC Berkeley 25
DFM Design GuidelinesInjection Molding
Provide smooth transition, avoid changes in thickness when possible.
Keep section thickness uniform around bosses.
Ken Youssefi UC Berkeley 26
DFM Design GuidelinesInjection Molding
• Use standard general tolerances, do not tolerance;
Dimension Tolerance Dimension Tolerance
0 ≤ d ≤ 25 ± 0.5 mm 0 ≤ d ≤ 1.0 ± 0.02 inch
25 ≤ d ≤ 125 ± 0.8 mm 1 ≤ d ≤ 5.0 ± 0.03 inch
125 ≤ d ≤ 300 ± 1.0 mm 5 ≤ d ≤ 12.0 ± 0.04 inch
300 ± 1.5 mm 12.0 ± 0.05 inch
• Minimum thickness recommended; .025 in or .65 mm, up to .125 for large parts.
• Round interior and exterior corners to .01-.015 in radius (min.), prevents an edge from chipping.
Standard thickness variation.
Ken Youssefi UC Berkeley 27
DFM Design GuidelinesRotational Molding
Rotational molding process consists of six steps
• A predetermined amount of plastic, powder or liquid form, is deposited in one half of a mold.
• The mold is closed.• The mold is rotated biaxially inside an oven.• The plastics melts and forms a coating over the inside
surface of the mold.• The mold is removed from the oven and cooled.• The part is removed from the mold.
Ken Youssefi UC Berkeley 28
Rotational Molding Machines
Rock and roll machine
Vertical wheel machine
Turret machine
Shuttle machine
Ken Youssefi UC Berkeley 29
Rotational MoldingAdvantages
• Molds are relatively inexpensive.• Rotational molding machines are much less
expensive than other type of plastic processing equipment.
• Different parts can be molded at the same time.
• Very large hollow parts can be made.• Parts are stress free.• Very little scrap is produced
Ken Youssefi UC Berkeley 30
Rotational MoldingLimitations
• Can not make parts with tight tolerance.
• Large flat surfaces are difficult to achieve.
• Molding cycles are long (10-20 min.)
Materials
Polyethylene (most common), Polycarbonate (high heat resistance and good impact strength), Nylon (good wear and abrasion resistance, good chemical resistance, good toughness and stiffness).
Ken Youssefi UC Berkeley 31
Rotational Molding
Nominal wall thickness
• Polycarbonate wall thickness is typically between .06 to .375 inches, .125 inch being an ideal thickness.
• Polyethylene wall thickness is in the range of .125 to .25 inch, up to 1 inch thick wall is possible
• Nylon wall thickness is in the range of .06 to .75 inch.
Ken Youssefi UC Berkeley 32
Rotational Molding Examples
Ken Youssefi UC Berkeley 33
Rotational Molding Examples
Ken Youssefi UC Berkeley 34
DFM Design GuidelinesSheet-metal Forming
Ken Youssefi UC Berkeley 35
DFM Design GuidelinesSheet-metal Forming
Ken Youssefi UC Berkeley 36
DFM Design GuidelinesSheet-metal Forming
Ken Youssefi UC Berkeley 37
DFM Design Guidelines - CastingCasting, one of the oldest manufacturing processes, dates back to 4000 B.C. when copper arrowheads were made. • Casting processes basically involve the introduction of a
molten metal into a mold cavity, where upon solidification, the metal takes on the shape of the mold cavity.
• Simple and complicated shapes can be made from any metal that can be melted.
• Example of cast parts: frames, structural parts, machine components, engine blocks, valves, pipes, statues, ornamental artifacts…..
• Casting sizes range form few mm (teeth of a zipper) to 10 m (propellers of ocean liners).
Ken Youssefi UC Berkeley 38
Casting Processes1. Preparing a mold cavity of the desired shape with
proper allowance for shrinkage.
2. Melting the metal with acceptable quality and temp.
3. Pouring the metal into the cavity and providing means for the escape of air or gases.
4. Solidification process, must be properly designed and controlled to avoid defects.
5. Mold removal.
6. Finishing, cleaning and inspection operations.
Ken Youssefi UC Berkeley 39
Sand Casting Terminology
Ken Youssefi UC Berkeley 40
Casting DefectsHot spots – thick sections cool slower than other sections causing abnormal shrinkage. Defects such as voids, cracks and porosity are created.
Ken Youssefi UC Berkeley 41
Casting Defects and Design Consideration
Ken Youssefi UC Berkeley 42
DFM Design Guidelines - Casting
Ken Youssefi UC Berkeley 43
DFM Design Guidelines - Casting
Ken Youssefi UC Berkeley 44
DFM Design Guidelines – Machining