Depth
1
108 Surface finishes unless otherwise stated: Sand-Cast = 16.0µm 1. Drilling = 6.3µm 2. Forging = 6.3µm 3. Milling = 3.2µm 4. Turning = 3.2µm 5. Boring = 3.2µm 6. Die-Cast = 1.6µm 7. Reaming = 1.6µm 8. Grinding = 0.8µm 9. Honing = 0.4µm 10. Polishing = 0.2µm 11. Limits unless otherwise stated: Fabricated 0.75 1. Sand-Cast 0.35 2. Forging 0.25 3. Die-Cast 0.25 4. Moulded 0.15 5. Machined 0.25mm 6. Angular 0.50degree 7. Fits unless otherwise stated: Free Running = H9/d9 1. Running = H8/f8 2. Clearance = H7/h6 3. Sliding = H7/g6 4. Interference = H7/u6 5. XXX.XX Features marked with this symbol: must be referred to in the manufacturing control plan THIRD ANGLE PROJECTION R 100 500 Upper edge of sink approx. 850 75 >=70 294 600 177 G1/2" Cable entry 36 SCALE 1 : 5 SIDE ELEVATION VIEW Depth of unit REVISIONS Rev XXXX YYYY Last Change(s) ECO Date Init A First Issue 0000 8/06/2011 NM Table - Zip BOM (Assembly) Item Part Rev Description Config Status Default/ Qty Notes 1 A2402 A Description (Assembly) For Chilltap & Filter Tap Production 1 2 87570! 00 Classic Mixer Tap Default Design 1 3 86451 A Nipple-Tapered 1/2" (No 27) Default Production 3 4 27920 A Instantaneous Hot Water CEX-U 13.5kW 3 x 20Amps 60ºC 801096 Production 1 5 84451 A Tee 1/2" BSP Female (Brass) Default Production 1 150 50 200 250 150 100 50 250 200 50 100 250 200 100 150 Web : www.zipindustries.com Email : [email protected] 100 300 400 400 300 350 350 550 450 500 400 350 300 150 200 250 300 350 Dimensions in millimetres Drawing to BS8888:2004 Screw threads to BS 8498:2008 File Ref : R:\!Released\WL005_27910 (Sheet1) Sheet1 (Default) Zip Industries Pty Ltd 67 Allingham Street Condell Park Sydney NSW 2200 Australia Handed? : Unchecked on 1/01/2001 edgarg on 15/06/2015 7:45:31 AM Updated by : EdgarG on 4/05/2011 A A2 Created by & on Created by & on Potable? : Recyclable? : No No Make Manufacturing Process Raw Material Comments Comments : Remove all sharp edges. This drawing ONLY details information which cannot be ascertained from the 3D geometry of the part(s) attached. Model & dimensions are AFTER all finishing operations Raw material : Manufacturing Route : Make or Buy : This drawing is CONFIDENTIAL and is supplied on the express condition that it shall not be LOANED, COPIED or DISCLOSED to any other third party or used for any purpose without the written consent of Zip Industries Pty Ltd. If this document is printed in hardcopy form, it is for INFORMATION ONLY and therefore not subject to updating controls. For the current revision ALWAYS refer to the NATIVE electronic form as stated in the top left-hand corner of this sheet. © copyright Zip Industries Pty Ltd, 16/05/2011 _Drawing Property Part Property Assy - Kitchen Layout Instantaneous Hot Water CEX9-U 8.8kW 38Amps, 50ºC WL005_27910 96031.62 Material <not specified> Sheet : 1 of 1 1:1 Unapproved on 1/03/2011 EdgarG on 16/05/2011 New Manufacturing Instructions Zip Industries WL005_27910 Drawing : Model : Description : Status : Derived from : Scale : Approved by : Checked by : Finish Finish : Material : Mass (g) : Density (g/cm3) : 1.10 Area (cm2) : 114027.95 87279.66 Volume (cm3) : Prototype Default Configuration : Instantaneous Hot Water® Project : Size Rev Colourless Colour :
Transcript of Depth
108
Surface finishes unless otherwise stated:
Sand-Cast = 16.0µm1.Drilling = 6.3µm2.Forging = 6.3µm3.Milling = 3.2µm4.Turning = 3.2µm5.Boring = 3.2µm6.Die-Cast = 1.6µm7.Reaming = 1.6µm8.Grinding = 0.8µm9.Honing = 0.4µm10.Polishing = 0.2µm11.
Limits unless otherwise stated:Fabricated 0.751.Sand-Cast 0.352.Forging 0.25 3.Die-Cast 0.254.Moulded 0.155.Machined 0.25mm6.Angular 0.50degree7.
Fits unless otherwise stated:Free Running = H9/d91.Running = H8/f82.Clearance = H7/h63.Sliding = H7/g64.Interference = H7/u65.
XXX.XXFeatures marked with this symbol:must be referred to in the manufacturing control plan
THIRD ANGLEPROJECTION
R
100
500
Uppe
r edg
e of
sink
app
rox.
850
75
>=70
294
600
177
G1/2"
Cable entry
36
SCALE 1 : 5SIDE ELEVATION VIEW
Depthof unit
REVISIONSRev XXXX
YYYY Last Change(s) ECO Date Init
A First Issue 0000 8/06/2011 NM
Table - Zip BOM (Assembly)Item Part Rev Description Config Status Default/
Qty Notes1 A2402 A Description (Assembly) For Chilltap &
Filter Tap Production 1
2 87570! 00 Classic Mixer Tap Default Design 1
3 86451 A Nipple-Tapered 1/2" (No 27) Default Production 3
4 27920 A Instantaneous Hot Water CEX-U 13.5kW 3 x 20Amps 60ºC 801096 Production 1
5 84451 A Tee 1/2" BSP Female (Brass) Default Production 1
150
50
200
250
15010050 250200
50 100
250
200
100
150
Web : www.zipindustries.comEmail : [email protected]
100
300
400 400
300
350 350
550450 500400350300
150 200 250 300 350
Dimensions in millimetres
Drawing to BS8888:2004
Screw threads to BS 8498:2008
File Ref : R:\!Released\WL005_27910 (Sheet1)
Sheet1 (Default) Zip Industries Pty Ltd67 Allingham StreetCondell ParkSydneyNSW 2200Australia
Handed? :
Unchecked on 1/01/2001
edgarg on 15/06/2015 7:45:31 AMUpdated by :
EdgarG on 4/05/2011
AA2
Created by & onCreated by & on
Potable? : Recyclable? :No No
Make
Manufacturing Process
Raw Material
CommentsComments :
Remove all sharp edges. This drawing ONLY details information which cannot be ascertained from the 3D geometry of the part(s) attached. Model & dimensions are AFTER all finishing operations
Raw material :
Manufacturing Route :
Make or Buy :
This drawing is CONFIDENTIAL and is supplied on the express condition that it shall not be LOANED, COPIED or DISCLOSED to any other third party or used for any purpose without the written consent of Zip Industries Pty Ltd. If this document is printed in hardcopy form, it is for INFORMATION ONLY and therefore not subject to updating controls.For the current revision ALWAYS refer to the NATIVE electronic form as stated in the top left-hand corner of this sheet.© copyright Zip Industries Pty Ltd, 16/05/2011
_DrawingProperty
PartProperty
Assy - Kitchen Layout Instantaneous Hot Water CEX9-U 8.8kW 38Amps, 50ºC
WL005_2791096031.62
Material <not specified>
Sheet : 1 of 11:1
Unapproved on 1/03/2011
EdgarGon 16/05/2011
New
Manufacturing Instructions
Zip Industries
WL005_27910Drawing :Model :
Description :
Status :
Derived from :
Scale :
Approved by :
Checked by :
FinishFinish :
Material :
Mass (g) : Density (g/cm3) : 1.10
Area (cm2) : 114027.9587279.66Volume (cm3) :
Prototype
DefaultConfiguration :Instantaneous Hot Water®Project :
Size
Rev
ColourlessColour :
