Denison Calzoni Type Mrt Mrte Mrtf
-
Upload
silvio-roman -
Category
Documents
-
view
220 -
download
0
Transcript of Denison Calzoni Type Mrt Mrte Mrtf
8/11/2019 Denison Calzoni Type Mrt Mrte Mrtf
http://slidepdf.com/reader/full/denison-calzoni-type-mrt-mrte-mrtf 1/24
DENISON CALZONI
Radial Piston Motor zm
Type MRT, MRTE, MRTF
CALZONI
RCOa 2301/03.03
8/11/2019 Denison Calzoni Type Mrt Mrte Mrtf
http://slidepdf.com/reader/full/denison-calzoni-type-mrt-mrte-mrtf 2/242RCOa 2301/03.03
TABLE OF CONTENS - MOTOR TYPE MRT - MRTE - MRTF
CONTENS PAG.
TABLE OF CONTENS 2
GENERAL CHARATERISTICS 3
FUNCTIONAL DESCRIPTION 4
TECHINICAL DATA 5
FLUID SELECTION 6
FLUSHING PROCEDURE 7
OPERATING DIAGRAM MOTOR TYPE MRT 7100 MRTF 8100 MRTE 8500 8
OPERATING DIAGRAM MOTOR TYPE MRT 9000 MRTF 9900 MRTE 10800 9
OPERATING DIAGRAM MOTOR TYPE MRT 14000 MRTF 15500 MRTE 16500 10
OPERATING DIAGRAM MOTOR TYPE MRT 17000 MRTF 18000 MRT 19500 11
OPERATING DIAGRAM MOTOR TYPE MRTE 20000 MRTF 21500 MRTE 23000 12
OPERATING DIAGRAM (RUNNING PRESSURE DIFFERENCE AT NO LOAD) 13-14
OPERATING DIAGRAM (MOTOR /PUMP: BOOST PRESSURE) 14-15
MOTOR DIMENSIONS 16-19
COMPONENTS FOR SPEED CONTROL 20-21
INSTALLATION NOTES 22
ORDERING CODE 23
SALES AND SERVICE LOCATIONS WORLDWIDE 24
The specified data are for product description purposes only and must not be interpreted as warranted characteristic in a legal sense.
All rights reserved. Subject to revision.
8/11/2019 Denison Calzoni Type Mrt Mrte Mrtf
http://slidepdf.com/reader/full/denison-calzoni-type-mrt-mrte-mrtf 3/243RCOa 2301/03.03
GENERAL CHARATERISTICS - MOTOR TYPE MRT - MRTE - MRTF
CONTRUCTION
TYPE
MOUNTING
CONNECTION
MOUNTING POSITION
DIRECTION OF ROTATION
FLUID
FLUID TEMPERATURE RANGE
VISCOSITY RANGE 1)
FLUID CLEANLINESS
Fixed displacement radial piston motor
MRT, MRTE, MRTF
Front flange mounting
Connection flange
Any (please note the installation notes on page 22)
Clockwise, anti-clockwise -reversible
HLP mineral oils to DIN 51 524 part 2; Fluid type HFB, HFC and Bio-fluids onenquiry. FPM seals are required with phosphorous acid-Ester (HFD)
t °F – 22° a + 176° (-30° a +80° C)
ν = 85 to 4635 SUS (18 to 1000 mm2 /s): Recommended operating range 141to 230 SUS (30 to 50 mm2 /s) (see fluid selection on page 6)
Maximum permissible degree of contamination of fluid NAS 1638 Class 9.We therefore recommend a filter with a minimum retention rate of ß
10 > 75.
To ensure a long life we recommend class 8 to NAS 1638.This can be achieved with a filter, with a minimum retention rate of ß
5 >100.
GENERAL CHARACTERISTICS
1) For different valves of viscosity please contact DENISON Calzoni
14 PISTONS MOTOR VERSION 10 PISTONS MOTOR VERSION
The specified data are for product description purposes only an d must not be interpreted as warranted characteristic in a legal sense. All
rights reserved. Subject to revision.
8/11/2019 Denison Calzoni Type Mrt Mrte Mrtf
http://slidepdf.com/reader/full/denison-calzoni-type-mrt-mrte-mrtf 4/244RCOa 2301/03.03
FUNCTIONAL DESCRIPTION - MOTOR TYPE MRT - MRTE - MRTF
FUNCTIONAL DESCRIPTION The outstanding performance, which is already known in our MR - MRE series motors, is
the result of an original and patented design. The principle is to transmit the effort from the
stator to the rotating shaft (1) by means of a pressurized column of oil (A) instead of the
more common connecting rods, pistons, pads and pins. This oil column is contained by a
telescopic cylinder (2) with a mechanical connection at the lips at each end which seal
against the spherical surfaces (3) of the cylinder-heads (4) and the spherical surface of the
rotating shaft (1). These lips retain their circular cross section when stressed by the
pressure so there is no alteration in the sealing geometry. The particular selection of
materials and optimisation of design has minimized both the friction and the leakage.
Another advantage of this design stems from the elimination of any connecting rods, the
cylinder can only expand and retract linearly so there are no transverse components of the
thrust. This means no oval wear on the moving parts and no side forces on the cylinder
joints. A consequence of this novel design as a 10 piston motor is the significant reduction
in dimensions. Especially the diameter is limitated to a value of motors with half of
its capacity. Performances reached by this motor type are improved with reference to other
motors of same diplacement. Another advantage stems from the geometrical arrangement
of the 10 - 14 pistons, that results in a static balance of the motor shaft and in a great
reduction of the reaction forces on the bearings with consequent large extension of their
life time.
TIMING SYSTEM The timing system is realized by means of a rotary valve (5) driven by the rotary valve
driving shaft (8) that it is connected to the rotating shaft. The rotary valve rotates between
the rotary valve plate (6) and the reaction ring (7) which are fixed with the motor's housing.
This timing system is also of a patented design being pressure balanced and self
compensating for thermal expansion. The motor sizes from MRTE 16500 to MRTE 23000
are available with large timing system option that allows higher motor power performances
as well as the possibility to have a throughhollow shaft (see pages 5, 18-19).
EFFICIENCY The advantages of this type of valve coupled with a revolutionary cylinder arrangement
produce a motor with extremly high values of mechanical and volumetric efficiency. The
torque output is smooth even at very low speed and the motor gives a high performance
starting under load.
The specified data are for product description purposes only and must not be interpreted as warranted characteristic in a legal sense.
All rights reserved. Subject to revision.
34
A
4
A
1
2
8657
8/11/2019 Denison Calzoni Type Mrt Mrte Mrtf
http://slidepdf.com/reader/full/denison-calzoni-type-mrt-mrte-mrtf 5/245RCOa 2301/03.03
TECHINICAL DATA - MOTOR TYPE MRT - MRTE - MRTF
The specified data are for product description purposes only and must not be interpreted as warranted characteristic in a legal sense.
All rights reserved. Subject to revision.
eziS eziS eziS eziS eziSrotoMnoisrev
-ecalpsiD -ecalpsiD -ecalpsiD -ecalpsiD -ecalpsiDtnem
tnemoM tnemoM tnemoM tnemoM tnemoMfoaitreni
gnitatorstrap
--eroehT --eroehT --eroehT --eroehT --eroehTlacit
cificepseuqrot
.niM .niM .niM .niM .niM.tratseuqrot
%--eroehT
laciteuqrot
erusserPnumixaM erusserPnumixaM erusserPnumixaM erusserPnumixaM erusserPnumixaM egnardeepS egnardeepS egnardeepS egnardeepS egnardeepS mumixaM mumixaM mumixaM mumixaM mumixaMtuptuo
rewop
thgieW thgieW thgieW thgieW thgieW
tupni gnihsulf gnihsulf
.tnoc .tni kaep B+A niarD tuohtiw htiw tuohtiw htiw
V J % p p p p p n n P P m
ni 3 tf.bl 2 isp / tf.bl isp isp isp isp isp mpr mpr pH pH bl
0017TRM 0017TRM 0017TRM 0017TRM 0017TRM 5.334 54.91 57.5 19 6263 1534 2906 2085
5.27812(
htiwisp
"1F"
tfahs)laes
57-5.0 051-5.0 1.303 5.244 8202
0087FTRM 0087FTRM 0087FTRM 0087FTRM 0087FTRM 5.674 54.91 23.6 19 6403 6263 6705 2085 07-5.0 031-5.0 1.652 5.573 8202
0058ETRM 0058ETRM 0058ETRM 0058ETRM 0058ETRM 8.915 54.91 09.6 19 6403 6263 6705 2085 06-5.0 021-5.0 5.562 9.883 8202
0009TRM 0009TRM 0009TRM 0009TRM 0009TRM 5.945 23.13 92.7 19 6263 1534 2906 2085 07-5.0 031-5.0 3.933 2.694 8202
0099FTRM 0099FTRM 0099FTRM 0099FTRM 0099FTRM 4.406 23.13 20.8 19 6403 6263 6705 2085 06-5.0 021-5.0 9.472 3.204 8202
00801ETRM 00801ETRM 00801ETRM 00801ETRM 00801ETRM 2.956 23.13 57.8 19 6403 6263 6705 2085 56-5.0 011-5.0 3.482 7.514 8202
00041TRM 00041TRM 00041TRM 00041TRM 00041TRM 9.458 0992 43.11 19 6263 1534 2906 2085 05-5.0 08-5.0 2.913 1.674 4386
00551FTRM 00551FTRM 00551FTRM 00551FTRM 00551FTRM 3.239 0992 63.21 19 6403 6263 6705 2085 04-5.0 57-5.0 6.372 904 7686
00561ETRM 00561ETRM 00561ETRM 00561ETRM 00561ETRM 5.9001 0992 93.31 19 6403 6263 6705 2085 04-5.0 07-5.0 3.672 314 0096
00071TRM 00071TRM 00071TRM 00071TRM 00071TRM 7.2201 0992 85.41 19 6263 1534 2906 2085 04-5.0 07-5.0 6.233 5.794 4386
00081FTRM 00081FTRM 00081FTRM 00081FTRM 00081FTRM 0.0011 0992 95.41 19 6403 6263 6705 2085 04-5.0 56-5.0 3.882 1.924 7686
00591TRM 00591TRM 00591TRM 00591TRM 00591TRM 5.0911 0992 97.51 19 6263 1534 2906 2085 53-5.0 06-5.0 6.233 5.794 4386
00002ETRM 00002ETRM 00002ETRM 00002ETRM 00002ETRM 5.7021 0992 10.61 19 6403 6263 6705 2085 53-5.0 06-5.0 3.482 8.324 0096
00512FTRM 00512FTRM 00512FTRM 00512FTRM 00512FTRM 0.8921 0992 12.71 19 6403 6263 6705 2085 03-5.0 55-5.0 3.082 1.714 7686
00032ETRM 00032ETRM 00032ETRM 00032ETRM 00032ETRM 6.5041 0992 46.81 19 6403 6263 6705 2085 03-5.0 05-5.0 9.472 4.014 0096
STANDARD TIMING TECHINICAL DATA
SPECIAL TIMING TECHINICAL DATA (please contact DENISON Calzoni)
eziS eziS eziS eziS eziS
rotoM
noisrev
-ecalpsiD -ecalpsiD -ecalpsiD -ecalpsiD -ecalpsiD
tnem
tnemoM tnemoM tnemoM tnemoM tnemoM
foaitreni
gnitator
strap
-eroehT -eroehT -eroehT -eroehT -eroehT
lacit
cificeps
euqrot
.niM .niM .niM .niM .niM
.trats
euqrot
%
-eroehT
lacit
euqrot
erusserPnumixaM erusserPnumixaM erusserPnumixaM erusserPnumixaM erusserPnumixaM egnardeepS egnardeepS egnardeepS egnardeepS egnardeepS mumixaM mumixaM mumixaM mumixaM mumixaM
tuptuo
rewop
thgieW thgieW thgieW thgieW thgieW
tupni gnihsulf gnihsulf
.tnoc .tni kaep B+A niarD tuohtiw htiw tuohtiw htiw
V J % p p p p p n n P P m
ni 3 ni.bl 2 isp / tf.bl isp isp isp isp isp mpr mpr pH pH bl
00561ETRM 00561ETRM 00561ETRM 00561ETRM 00561ETRM 5.9001 0992 93.31 19 6403 6263 6705 2085
5.27
812(
htiwisp
"1F"
tfahs
)laes
05-5.0 08-5.0 5.613 274 0096
00071TRM 00071TRM 00071TRM 00071TRM 00071TRM 7.2201 0992 65.31 19 6263 1534 2906 2085 05-5.0 08-5.0 9.083 9.965 4386
00081FTRM 00081FTRM 00081FTRM 00081FTRM 00081FTRM 0.0011 0992 95.41 19 6403 6263 6705 2085 05-5.0 08-5.0 6.233 2.694 7686
00591TRM 00591TRM 00591TRM 00591TRM 00591TRM 5.0911 0992 97.51 19 6263 1534 2906 2085 05-5.0 08-5.0 9.344 5.266 4386
00002ETRM 00002ETRM 00002ETRM 00002ETRM 00002ETRM 5.7021 0992 10.61 19 6403 6263 6705 2085 54-5.0 57-5.0 4.553 7.925 0096
00512FTRM 00512FTRM 00512FTRM 00512FTRM 00512FTRM 0.8921 0992 12.71 19 6403 6263 6705 2085 54-5.0 57-5.0 9.083 9.965 7686
00032ETRM 00032ETRM 00032ETRM 00032ETRM 00032ETRM 6.5041 0992 46.81 19 6403 6263 6705 2085 54-5.0 57-5.0 9.083 9.616 0096
(*) Please contact DENISON Calzoni
8/11/2019 Denison Calzoni Type Mrt Mrte Mrtf
http://slidepdf.com/reader/full/denison-calzoni-type-mrt-mrte-mrtf 6/246RCOa 2301/03.03
OIL SELECTION - MOTOR TYPE MRT - MRTE - MRTF
The specified data are for product description purposes only and must not be interpreted as warranted characteristic in a legal sense.
All rights reserved. Subject to revision.
EXAMPLE: At a certain ambient
temperature, the operating temperature in
the circuit is 122°F (50°C). In the optimum
operating viscosity range (vrec
; shaded
section), this corresponds to viscosity
grades VG 46 or VG 68; VG 68 should be
selected.
IMPORTANT: The drain oil temperature
is influenced by pressure and speed and isusually higher than the circuit temperature
or the tank temperature. At no point in the
system, however, may the temperature be
higher than 176°F (80°C).
If the optimum conditions cannot be met
due to the extreme operating parameters or
high ambient temperature, we always
recommend flushing the motor case in
order to operate within the viscosity limits.
Should it be absolutely necessary to use a
viscosity beyond the recommended range,
you should first contact DENISON Calzoni
for confirmation.
GENERAL NOTES More detailed information regarding the choice of the fluid can be requested to DENISON
Calzoni. Further notes on installation and commissioning can be found on page 22 of this data
sheet. When operating with HF pressure fluids or bio-degradable pressure fluids possible
limitations of the technical data must be taken into consideration, please see information sheet
TCS 85, or consult DENISON Calzoni.
OPERATING VISCOSITY RANGE The viscosity, quality and cleanliness of operating fluids are decisive factors in determining
the reliability, performance and life-time of an hydraulic component. The maximum life-time
and performance are achieved within the recommended viscosity range. For applications that
go beyond this range, we recommend to contact DENISON Calzoni.
ν rec.
= recommended operating viscosity 141...230 SUS (30...50 mm2 /s)
This viscosity refers to the temperature of the fluid entering the motor, and at the same time
to the temperature inside the motor housing (case temperature). We recommend to select theviscosity of the fluid based on the maximum operating temperature, to remain within the
recommended viscosity range. To reach the value of maximum continuous power the
operating viscosity should be within the recommended viscosity range of 30 - 50 cSt.
LIMITS OF VISCOSITY RANGE For limit conditions the following is valid:
ν min.abs.
= 45 SUS (10 mm2 /s) in emergency, short term
ν min.
= 85 SUS (18 mm2 /s) for continuous operation at reduced performances
ν max.
= 4635 SUS (1000 mm2 /s) short term upon cold start
CHOOSING THE TYPE OF FLUID The operating temperature of the motor is defined as the greater temperature between that of the
ACCORDING TO THE OPERATING incoming fluid and that of the fluid inside the motor housing (case temperature).WeTEMPERATURE recommend that you choose the viscosity of the fluid based on the maximum operating
temperature, to remain within the recommended viscosity range (see diagram). We
recommend that the higher viscosity grade must be selected in each case.
FILTRATION The motor life also depends on the fluid filtration. At least it must correspond to one of the
following cleanliness. class 9 according to NAS 1638
class 6 according to SAE, ASTM, AIA
class 18/15 according to ISO/DIS 4406
In order to assure a longer life a cleanliness class 8 to NAS 1638 is recommended, achieved
with a filter of β 5=100. In case the above mentioned classes can not be achieved, please consult us.
CASE DRAIN PRESSURE The lower the speed and the case drain pressure, the longer the life of the shaft seal. The
maximum permissible housing pressure is
p max
= 72.5 psi
If the case drain pressure is higher than 72.5 psi it is possible to use a special 218 psi shaft seal
(see page 23, Seals, Code"F1").
"FPM" SEALS In case of operating conditions with high oil temperature or high ambient temperature, we
recommend to use "FPM" seals (see page 23, Seals, Code "V1"). These "FPM" seals should beused with HFD fluids.
Temperature t in °F ( °C)
Oil temperature range
v i s c o s i t y ν
( m m
2 / s )
5000
30002000
1000
800
600
500
230
100
90
80
70
60
400
141
300
v i s c o s i t y ν
( S U S )
ν R E C
(-30) (80)(70)(60)(50)(40)(30)(20)(10)(0)(-10)(-20)
-22 1761581401221048668503214-4
8/11/2019 Denison Calzoni Type Mrt Mrte Mrtf
http://slidepdf.com/reader/full/denison-calzoni-type-mrt-mrte-mrtf 7/247RCOa 2301/03.03
FLUSHING PROCEDURE - MOTOR TYPE MRT - MRTE - MRTF
FLUSHING CIRCUIT
FLUSHING PROCEDURE In order to achieve the maximum continuous performance values the flushing of the
housing is necessary (see diagrams pages 8 to 12).
Under special conditions, in order to achieve the recommended operating viscosity of
141-230 SUS (30 - 50 mm2 /s) in the motor housing, the flushing of the motor may be
necessary also in the "operating area without flushing" see page 6 and the "operating
diagram" page 7 to12.
NOTE1: The oil temperature inside the motor housing is obtainable by adding 5°F (3° C) to the motor
housing surface temperature, measured between two cylinders (t A , see figures).
FUNCTION: The flushing valve takes the flushing flow always from the low pressure line of the motor.
The diameter of the orifice has to be chosen in order to supply the recommended quantity
of flushing flow of 6 gpm (23 l/min).
The specified data are for product description purposes only and must not be interpreted as warranted characteristic in a legal sense.
All rights reserved. Subject to revision.
Temperature t A
"A"
"A"Orifice M10
B
A
ERUSSERPKCAB )isp( RETEMAIDECIFIRO )hcni(
5.34 981.0
0.78 851.0
5.031 241.0
6.712 621.0
1.092 811.0
6.263 411.0
1.534 011.0
NOTE2: The flushing valve is delivered with a "closed"orifice.
Caution: Flushing does not work until the "closed" orifice is replaced bythe proper one.
8/11/2019 Denison Calzoni Type Mrt Mrte Mrtf
http://slidepdf.com/reader/full/denison-calzoni-type-mrt-mrte-mrtf 8/248RCOa 2301/03.03
OPERATING DIAGRAM - MOTOR TYPE MRT - MRTE - MRTF
The specified data are for product description purposes only and must not be interpreted as warranted characteristic in a legal sense.
All rights reserved. Subject to revision.
11111 Output power 2 Intermittent operating area 3 Continuous operating area with flushing
4 Continuous operating area 5 Inlet pressure ηηηηηt t t t t Total efficiency ηηηηηv v v v v Volumeter efficiency
OPERATING DIAGRAM (average values) measured at ν = 167 SUS (36 mm2 /s); t = 113°F (45° C);
p outlet
= 0 psi (0 bar)
8/11/2019 Denison Calzoni Type Mrt Mrte Mrtf
http://slidepdf.com/reader/full/denison-calzoni-type-mrt-mrte-mrtf 9/249RCOa 2301/03.03
OPERATING DIAGRAM - MOTOR TYPE MRT - MRTE - MRTF
The specified data are for product description purposes only and must not be interpreted as warranted characteristic in a legal sense.
All rights reserved. Subject to revision.
11111 Output power 2 Intermittent operating area 3 Continuous operating area with flushing
4 Continuous operating area 5 Inlet pressure ηηηηηt t t t t Total efficiency ηηηηηv v v v v Volumeter efficiency
OPERATING DIAGRAM (average values) measured at ν = 167 SUS (36 mm2 /s); t = 113°F (45° C);
p outlet
= 0 psi (0 bar)
8/11/2019 Denison Calzoni Type Mrt Mrte Mrtf
http://slidepdf.com/reader/full/denison-calzoni-type-mrt-mrte-mrtf 10/2410RCOa 2301/03.03
OPERATING DIAGRAM - MOTOR TYPE MRT - MRTE - MRTF
The specified data are for product description purposes only and must not be interpreted as warranted characteristic in a legal sense.
All rights reserved. Subject to revision.
11111 Output power 2 Intermittent operating area 3 Continuous operating area with flushing
4 Continuous operating area 5 Inlet pressure ηηηηηt t t t t Total efficiency ηηηηηv v v v v Volumeter efficiency
OPERATING DIAGRAM (average values) measured at ν = 167 SUS (36 mm2 /s); t = 113°F (45° C);
p outlet
= 0 psi (0 bar)
8/11/2019 Denison Calzoni Type Mrt Mrte Mrtf
http://slidepdf.com/reader/full/denison-calzoni-type-mrt-mrte-mrtf 11/2411RCOa 2301/03.03
OPERATING DIAGRAM - MOTOR TYPE MRT - MRTE - MRTF
The specified data are for product description purposes only and must not be interpreted as warranted characteristic in a legal sense.
All rights reserved. Subject to revision.
11111 Output power 2 Intermittent operating area 3 Continuous operating area with flushing
4 Continuous operating area 5 Inlet pressure ηηηηηt t t t t Total efficiency ηηηηηv v v v v Volumeter efficiency
OPERATING DIAGRAM (average values) measured at ν = 167 SUS (36 mm2 /s); t = 113°F (45° C);
p outlet
= 0 psi (0 bar)
8/11/2019 Denison Calzoni Type Mrt Mrte Mrtf
http://slidepdf.com/reader/full/denison-calzoni-type-mrt-mrte-mrtf 12/2412RCOa 2301/03.03
OPERATING DIAGRAM - MOTOR TYPE MRT - MRTE - MRTF
The specified data are for product description purposes only and must not be interpreted as warranted characteristic in a legal sense.
All rights reserved. Subject to revision.
11111 Output power 2 Intermittent operating area 3 Continuous operating area with flushing
4 Continuous operating area 5 Inlet pressure ηηηηηt t t t t Total efficiency ηηηηηv v v v v Volumeter efficiency
OPERATING DIAGRAM (average values) measured at ν = 167 SUS (36 mm2 /s); t = 113°F (45° C);
p outlet
= 0 psi (0 bar)
8/11/2019 Denison Calzoni Type Mrt Mrte Mrtf
http://slidepdf.com/reader/full/denison-calzoni-type-mrt-mrte-mrtf 13/2413RCOa 2301/03.03
MRT - MRTE - MRTF
14000 - 16500
MRT - MRTE - MRTF17000 - 20000
OPERATING DIAGRAM - MOTOR TYPE MRT - MRTE - MRTF
MRT - MRTE - MRTF
7100 - 8500
MRT - MRTE - MRTF
9000 - 10800
The specified data are for product description purposes only and must not be interpreted as warranted characteristic in a legal sense.
All rights reserved. Subject to revision.
OPERATING DIAGRAM (average values) measured at ν = 167 SUS (36 mm2 /s); t = 113°F (45° C);
Min. required pressure difference ∆∆∆∆∆p with idling speed (shaft unloaded) p outlet
= 0 psi (0 bar)
8/11/2019 Denison Calzoni Type Mrt Mrte Mrtf
http://slidepdf.com/reader/full/denison-calzoni-type-mrt-mrte-mrtf 14/2414RCOa 2301/03.03
Minimum boost pressure during pump operation
OPERATING DIAGRAM - MOTOR TYPE MRT - MRTE - MRTF
MRT - MRTE - MRTF
7100 - 8500
MRT - MRTE - MRTF
9000 -10800
The specified data are for product description purposes only and must not be interpreted as warranted characteristic in a legal sense.
All rights reserved. Subject to revision.
MRT - MRTE - MRTF
19500 - 23000
OPERATING DIAGRAM (average values) measured at ν = 167 SUS (36 mm2 /s); t = 113°F (45° C);
Min. required pressure difference ∆∆∆∆∆p with idling speed (shaft unloaded) p outlet
= 0 psi (0 bar)
8/11/2019 Denison Calzoni Type Mrt Mrte Mrtf
http://slidepdf.com/reader/full/denison-calzoni-type-mrt-mrte-mrtf 15/2415RCOa 2301/03.03
OPERATING DIAGRAM - MOTOR TYPE MRT - MRTE - MRTF
MRT - MRTE - MRTF
14000 - 16500
MRT - MRTE - MRTF
17000 - 20000
MRT - MRTE - MRTF
19500 - 23000
The specified data are for product description purposes only and must not be interpreted as warranted characteristic in a legal sense.
All rights reserved. Subject to revision.
OPERATING DIAGRAM (average values) measured at ν = 167 SUS (36 mm2 /s); t = 113°F (45° C);
Minimum boost pressure during pump operation p outlet
= 0 psi (0 bar)
8/11/2019 Denison Calzoni Type Mrt Mrte Mrtf
http://slidepdf.com/reader/full/denison-calzoni-type-mrt-mrte-mrtf 16/2416RCOa 2301/03.03
MOTOR DIMENSIONS - MOTOR TYPE MRT - MRTE - MRTF
The specified data are for product description purposes only and must not be interpreted as warranted characteristic in a legal sense.
All rights reserved. Subject to revision.
1
O n r e q u e s t p o r t f l a n g e c a n b e
r o t a t e d b y 7 2 °
* )
T h e s e S A E p o r t s a r e p r e s e n t o n l y i n t h e
M R T 9 0 0 0 P , M R T F 9 9 0 0 P , M R T E 1 0 8 0 0 P ,
M R T 1 4 0 0 0 Q , M T R F 1 5 5 0 0 Q , M R T E 1
6 5 0 0 ,
M R T 1 7 0 0 0 Q , M R T F 1 8 0 0 0 Q , M R T 1
9 5 0 0 Q ,
M R T E 2 0 0 0 0 Q , M R T F 2 1 5 0 0 Q e
M R T
E 2 3 0 0 0 Q
2
C a s e d r a i n p o r t
B S P t h r e a d s t o
I S O 2
2 8 / 1
3
S e e d i m e n s i o n
s a t p a g e 1 7
4
P o r t 1 / 4 “
B S P t
h r e a d s t o I S O 2
2 8 / 1
f o r p r e s s u r e r e a d i n g .
2
3
4
1 2
2
* )
* )
T
T T
T
f o . r i D
n o i t a t o R
n o d e w e i V (
) d n e t f a h s
t
e l n i t r o P
e d o c g n i r e d r o
) 3 2 e g a p e e s (
e s i w k c o l c
e s i w k c o l c - i t n a
A B
" N "
e s i w k c o l c
e s i w k c o l c - i t n a
B A
" S "
8/11/2019 Denison Calzoni Type Mrt Mrte Mrtf
http://slidepdf.com/reader/full/denison-calzoni-type-mrt-mrte-mrtf 17/2417RCOa 2301/03.03
MOTOR DIMENSIONS - MOTOR TYPE MRT - MRTE - MRTF
The specified data are for product description purposes only and must not be interpreted as warranted characteristic in a legal sense.
All rights reserved. Subject to revision.
E P Y T
R O T O M
E P Y T
R O T O M
E P Y T
R O T O M
E P Y T
R O T O M
E P Y T
R O T O M
1 L 1 L 1 L 1 L 1 L
) h c n i (
2 L 2 L 2 L 2 L 2 L
) h c n i (
3 L 3 L 3 L 3 L 3 L
)
h c n i (
4 L 4 L 4 L 4 L 4 L
) h c n i (
6 L 6 L 6 L 6 L 6 L
- c n i (
) h
7 L 7 L 7 L 7 L 7 L
- c n i (
) h
8 L 8 L 8 L 8 L 8 L
- c n i (
) h
9 L 9 L 9 L 9 L 9 L
) h c n i (
0 1 L
0 1 L
0 1 L
0 1 L
0 1 L
- c n i (
) h
1 1 L
1 1 L
1 1 L
1 1 L
1 1 L
- c n i (
) h
2 1 L
2 1 L
2 1 L
2 1 L
2 1 L
- c n i (
) h
3 1 L
3 1 L
3 1 L
3 1 L
3 1 L
- c n i (
) h
4 1 L
4 1 L
4 1 L
4 1 L
4 1 L
- c n i (
) h
5
1 L
5
1 L
5
1 L
5
1 L
5
1 L
- c
n i (
)
h
6 1 L
6 1 L
6 1 L
6 1 L
6 1 L
- c n i (
) h
7 1 L
7 1 L
7 1 L
7 1 L
7 1 L
- c n i (
) h
9 1 L
9 1 L
9 1 L
9 1 L
9 1 L
h c n i (
1 B 1 B 1 B 1 B 1 B
- c n i (
) h
2 B 2 B 2 B 2 B 2 B
- c n i (
) h
3 B 3 B 3 B 3 B 3 B
) h c n i (
4 B 4 B 4 B 4 B 4 B
- c n i (
) h
5 B 5 B 5 B 5 B 5 B
- c n i (
) h
E A S
E A S
E A S
E A S
E A S
i s p 0 0 0 3
E A
S
E A
S
E A
S
E A
S
E A
S
i s p 0 0 0 6
E A S E A S E A S E A S E A S
i s p 0 0 0 3
E A S
E A S
E A S
E A S
E A S
i s p 0 0 0 6
0 0 1 7 T R M
0 0 1 7 T R M
0 0 1 7 T R M
0 0 1 7 T R M
0 0 1 7 T R M
0 0 8 7 F T R M
0 0 5 8 E T R M
0 0 0 9 T R M
0 0 9 9 F T R M
0 0 8 0 1 E T R M
6 0 1 . 7 2
1 3 8 . 6 2
5 3 . 4 2
7 5 6 . 7 1
1 8 1 . 1
8 7 3 . 1
2 1 5 . 5
2 6 0 . 3
1 1 8 . 3
3 6 . 0 1
7 8 0 . 7
4 8 9 . 0
6 3 2 . 5
9 1 3 . 1 2
8 1
1 . 5
1 1 8 . 1 1
3 2 8 . 9 1
2 3 7 . 1
9 4 4 . 9
4 2 7 . 4
8 8 6 . 1
8 4 7 . 1
6 4 3 . 8
1 1 8 . 1 1
C o d e
D 1 - D I N
5 4 8 0
E P Y T
R O T O M
E P Y T
R O T O M
E P Y T
R O T O M
E P Y T
R O T O M
E P Y T
R O T O M
1 F 1 F 1 F 1 F 1 F
1 D 1 D 1 D 1 D 1 D
5 L 5 L 5 L 5 L 5 L
) h c n i (
1 2 L
1 2 L
1 2 L
1 2 L
1 2 L
) h c n i (
2 2 L
2 2 L
2 2 L
2 2 L
2 2 L
) h c n i (
3 1 D
Ø
3 1 D
Ø
3 1 D
Ø
3 1 D
Ø
3 1 D
Ø
0 8 4 5
N I D
X
Ø
X
Ø
X
Ø
X
Ø
X
Ø
8 h 8 h 8 h 8 h 8 h ) h c n i (
) h c n i (
) h c n i (
) h c n i (
) h c n i (
Y
Ø
Y
Ø
Y
Ø
Y
Ø
Y
Ø
) h c n i (
5 L 5 L 5 L 5 L 5 L
) h c n i (
1 2 L 1 2 L 1 2 L 1 2 L 1 2 L
) h c n i (
2 2 L
2 2 L
2 2 L
2 2 L
2 2 L
) h c n i (
3 1 D
Ø
3 1 D
Ø
3 1 D
Ø
3 1 D
Ø
3 1 D
Ø
0 8 4 5 N I D
2 1 D
2 1 D
2 1 D
2 1 D
2 1 D
) m m (
0 1 T
0 1 T
0 1 T
0 1 T
0 1 T
) h c n i (
0 0 1 7 T R M
0 0 1 7 T R M
0 0 1 7 T R M
0 0 1 7 T R M
0 0 1 7 T R M
0 0 8 7 F T R M
0 0 5 8 E T R M
9 6 9 . 1
4 2 7 4 . 0
1 7 0 . 3
H 9 - 5 3 x 3 x 0 1 1 N
3 4 5 3 . 5
2 5 3 . 5
) m m 6 3 1 (
6 9 1 . 0
- -
- -
- -
- -
- -
- -
0 0 0 9 T R M
0 0 0 9 T R M
0 0 0 9 T R M
0 0 0 9 T R M
0 0 0 9 T R M
0 0 9 9 F T R M
0 0 8 0 1 E T R M
0 4 7 . 3
4 2 7 4 . 0
1 7 0 . 3
H 9 - 8 2 x 4 x 0 2 1 N
3 4 5 3 . 5
2 5 3 . 5
) m m 6 3 1 (
8 6 9 . 1
3 4 8 . 9
1 7 0 . 8
5 7 5 . 6
f 8 - 6 2 x 5 x 0 4 1
W
2 1 M
4 8 9 . 0
a e r e h d e t s i l s e n o e h t m o r f t n e r e f f i d e r a n o i t a c i l p p a e h t y b d e r i u q e r s n o i s n e m i d s e l o h e h t e s a c n I . s e l o h e c i v r e s
s a d e r e d i s n o c e b t s u m " " 1 D " " s n o i s r e v t f a h s
e h t r o f ) 0 1 T / 2 1 D ( s e l o h d e d a e r h t e h t : E T O N
, e v o b
. i n o z l a C N O S I N E D t c a t n o c e s e l p
C o d e F 1 - D I N
5 4 8 0
E P Y T R O T O M
E P Y T R O T O M
E P Y T R O T O M
E P Y T R O T O M
E P Y T R O T O M
Ø ØØ Ø Ø 1
D
) h c n i (
Ø ØØ Ø Ø 2
D
) h c n i (
Ø ØØ Ø Ø 3
D
) h c n i (
Ø ØØ Ø Ø 4 D
7 h 7 h 7 h 7 h 7 h
) h c n i (
) h c n i (
) h c n i (
) h c n i (
) h c n i (
Ø ØØ Ø Ø 5
D
) h c n i (
) m m (
6 D
) m m (
6 D
) m m (
6 D
) m m (
6 D
) m m (
6 D
) h c n i
( 1 T
) h c n
i ( 1 T
) h c n
i ( 1 T
) h c n
i ( 1 T
) h c n i
( 1 T
7 D 7
D 7
D 7
D 7
D
Ø ØØ Ø Ø 8
D
) h c n i (
Ø ØØ Ø Ø 9
D
) h c n i (
Ø ØØ Ø Ø 0 1 D
) h c n i (
α αα α α
β ββ β β 1 11 1 1
β ββ β β 2 22 2 2
E A S
E A S
E A S
E A S
E A S
i s p
0 0 0 3
E A S
E A S
E A S
E A S
E A S
i s p
0 0 0 6
E A S
E A S
E A S
E A S
E A S
i s p
0 0 0 3
E A S
E A S
E A S
E A S
E A S
i s p
0 0 0 6
0 0 1 7
T R M
0 0 1 7
T R M
0 0 1 7
T R M
0 0 1 7
T R M
0 0 1 7
T R M
0 0 8 7
F T R M
0 0 5
8 E T R M
0 0 0 9 T R M
0 0 9 9 F T R M
0 0 8 0 1 E T R M
7 5 1 . 0 3
2 2 6 . 3 2
4 1 6 . 6 2
4 6 1 7 . 7 1
0 4 1 7 . 7 1
) m m 0 5 4 (
2 7 4 . 0 1
2 1 M
0 2 M
0 1 . 1
5 7 5 . 1
" 1 G
9 9 2 . 1
) 5 x (
5 9 7 . 2 1
9 6 9 . 1
°
0 9
°
6 3
°
8 1
8/11/2019 Denison Calzoni Type Mrt Mrte Mrtf
http://slidepdf.com/reader/full/denison-calzoni-type-mrt-mrte-mrtf 18/2418RCOa 2301/03.03
MOTOR DIMENSIONS - MOTOR TYPE MRT - MRTE - MRTF
The specified data are for product description purposes only and must not be interpreted as warranted characteristic in a legal sense.
All rights reserved. Subject to revision.
f o . r i D
n o i t a t o R
n o d e w e i V (
) d n e t f a h s
t e l n i t r o P
e d o c g n i r e d r o
) 3 2 e g a p e e s (
e s i w k c o l c
e s i w k c o l c - i t n a
A B
" N "
e s i w k c o l c
e s i w k c o l c - i t n a
B A
" S "
1
O n r e q u e s t p o r t f l a n g e c a n b e r o t a t e d b y 7 2 °
* )
T h e s e S A E p o r t s a r e p r e s e n t o n l y i n t h e
M R T 1 4 0 0 0 Q , M T R F 1 5 5 0 0 Q , M R T E 1 6 5
0 0 , M R T 1 7 0 0 0 Q ,
M R T F 1 8 0 0 0 Q , M R T 1 9 5 0 0 Q , M R T E 2 0
0 0 0 Q , M R T F 2 1 5 0 0 Q e
M R T E 2 3 0 0 0 Q
2
C a s e d r a i n p o r t B S P t h r e a d s t o I S O
2 2 8 / 1
3
S e e d i m e n s i o n s a t p a g e 1 9
4
P o r t 1 / 4 “
B S P t h r e a d s t o I S O 2
2 8 / 1
f o r p r e s s u r e r e a d i n g .
* )
S P E C I A L T I M I N G
3
4 1
2
2
2
* )
8/11/2019 Denison Calzoni Type Mrt Mrte Mrtf
http://slidepdf.com/reader/full/denison-calzoni-type-mrt-mrte-mrtf 19/24
8/11/2019 Denison Calzoni Type Mrt Mrte Mrtf
http://slidepdf.com/reader/full/denison-calzoni-type-mrt-mrte-mrtf 20/2420RCOa 2301/03.03
COMPONENTS FOR SPEED CONTROL - MOTOR TYPE MRT - MRTE - MRTF
MECHANICAL
TACHOMETER DRIVE
TACHOGENERATOR
DRIVE
ENCODERDRIVE
(see page 16-19)
INCREMENTAL ENCODER
DIMENSIONS
The specified data are for product description purposes only and must not be interpreted as warranted characteristic in a legal sense.
All rights reserved. Subject to revision.
Dimensions in inch (threaded holes in mm)
2x M8x1.77
Code "C1" Code "T1" Code "Q1"
2x M8x1.77 2x M8x1.18
10.59
0.35
10.28
0.29
0.190.190.190.31
0.98
1.10 0.29
1
2.38
1.10
φ φ φ φ φ
2 . 5
1 7 3
- φ φ φ φ φ
2 . 5
1 8 4
1 . 8
9
φ φ φ φ φ
0 . 7
8 7 3
- φ
φ
φ
φ
φ
0 . 7
9 0 7
0 . 5
5
0 . 2
3
0 . 1
0 2
φ φ φ φ φ
2 . 5
1 7 3
- φ φ φ φ φ
2 . 5
1 8 4
1 . 8
9
φ φ φ φ φ
0 . 8
6 6 1
- φ φ φ φφ
0 . 8
6 6 9
0 . 2
3
0 . 1
0 2
φ φ φ φ φ
2 . 5
1 7 3
- φ φ φ φ φ
2 . 5
1 8 4
1 . 8
9
φ φ φ φ φ
0 . 8
6 6 1
- φ φ φ φ φ
0 . 8
6 6 9
φ φ φ φ φ
0 . 3
1 4 3
- φ φ φ φ φ
0 . 3
1 4 9
Timing standard
encoder
encoder drive flangeprotection
Female connector included in the supply
ααααα = 45°
α α α α α
Timing standard
Dimensions in inch (threaded holes in mm)
3 . 6 6
2.40
1 9 7
8/11/2019 Denison Calzoni Type Mrt Mrte Mrtf
http://slidepdf.com/reader/full/denison-calzoni-type-mrt-mrte-mrtf 21/2421RCOa 2301/03.03
COMPONENTS FOR SPEED CONTROL - MOTOR TYPE MRT - MRTE - MRTF
INCREMENTAL ENCODER
TECHNICAL DATA
Monodirectional
4 3 3 4
1 1
4 3 3 4
1 1
1 1 1
4 4
1
4 4
3 3 3 3
2 2
Femaleconnector
Maleconnector
Maleconnector
INCREMENTAL ENCODER
CONNECTION DIAGRAMS
Bidirectional
2 2
Female
connector
noitcnufdnaseriwroloC noitcnufdnaseriwroloC noitcnufdnaseriwroloC noitcnufdnaseriwroloC noitcnufdnaseriwroloC
11111 nworB nworB nworB nworB nworB )cdV42ot8(ylppuSrewoP
22222 etihW etihW etihW etihW etihW )ccV42-Am01XAM(esahpBtuptuO
33333 eulB eulB eulB eulB eulB )cdV0(ylppuSrewoP
44444 k calB k calB k calB k calB k calB )ccV42-Am01XAM(esahpAtuptuO
The specified data are for product description purposes only and must not be interpreted as warranted characteristic in a legal sense.
All rights reserved. Subject to revision.
Encoder type: ELCIS mod. 478
Supply voltage: 8 to 24 Vcc
Current consumption: 120 mA max
Current output: 10 mA max
Output signal: A phase- MONODIRECTIONAL
A and B phase BIDIRECTIONAL
Response frequency: 100 KHz max
Number of pulses: 500 (others on request - max 2540)
Slew speed: Always compatible with maximum
motor speed
Operating temperature range: from 32 to 158 °F
Storage temperature range: from -22 to +185 °F
Ball bearing life: 1.5x109 rpm
Weigth: 0,220 lb
Protection degree: IP 67 (with protection and
connector assembled)
Connectors:
MONODIRECTIONAL RSF3/0.5 M (Lumberg) male
RKT3-06/5m (Lumberg) female
BIDIRECTIONAL RSF4/0.5 M (Lumberg) male
RKT4-07/5m (Lumberg) female
Note: Female connectors cable length equal to 16.4 foot (ft).
8/11/2019 Denison Calzoni Type Mrt Mrte Mrtf
http://slidepdf.com/reader/full/denison-calzoni-type-mrt-mrte-mrtf 22/2422RCOa 2301/03.03
INSTALLATION NOTES - MOTOR TYPE MRT - MRTE - MRTF
The specified data are for product description purposes only and must not be interpreted as warranted characteristic in a legal sense.
All rights reserved. Subject to revision.
Mounting
Any mounting position
- Note the position of the case drain port
(see below)
Install the motor properly
- Mounting surface must be flat and resistant to
bending
Min. tensile strength of mounting screws toDIN 267 Part 3 class 10.9
- Note the prescribed fastening torque
Pipes, pipe connections
Use suitable screws!
- Depending on type of motor use either
threaded or flange connection
Choose pipes and hoses suitable for the installation
- Please note manufacturing data!
Before operation fill with hydraulic fluid
- Use the prescribed filter!
Note:Two of the mounting screws must be precisely located/fitted if operation is started and stopped frequently or ifhigh reversible frequencies exist.
Curved toothcoupling hub
Screw to removethe coupling hub
Coupling
Mounting with screws
Use thread borein the drive shaft
Take apart withextractor
Note: Install leakage line in such a way thatmotor cannot run empty.
Low pressure case drain returns to tank
Note: Install leakage line in such a way that motor cannot run empty.
DRAIN AND FLUSHING LINK INSTALLATION EXAMPLES
T = SealY = Motor housing feeding point
= Bleed
2 alternative case drain portsin the first cilinder rowat 120° one from another
Bleed point
*) N° 2 Bleedscrews forbleeding(on request)
Cooling circuits for heavyduty continuous operation
Flushingp
max = 72.5 psi
with standard shaft seal
Bleed point
Overhead tank(release for bleeding)
Choose drain port in order to allow the complete filling of the housing with hydraulic fluid.
*) Bleed screw (on enquiry)
1 . 9
7 ( i n )
*) Special designs for applications, where the equipment needs to be filled with oil.(e.g. in a salty atmosphere)
8/11/2019 Denison Calzoni Type Mrt Mrte Mrtf
http://slidepdf.com/reader/full/denison-calzoni-type-mrt-mrte-mrtf 23/2423RCOa 2301/03.03
ORDERING CODE - MOTOR TYPE MRT - MRTE - MRTF
The specified data are for product description purposes only and must not be interpreted as warranted characteristic in a legal sense.
All rights reserved. Subject to revision.
CODE Example: MRT 7100P - D1 M1 F1 S1 N **
1D1D1D1D1D )71egapees(0845NIDenilps
1F1F1F1F1F )91-71egapees(0845NIDenilpselamef
3. MRT 7100P - D1 M1 F1 S1 N **
1N1N1N1N1N enon
1Q1Q1Q1Q1Q )02egapees(evirdredocne
1C1C1C1C1C )02egapees(evirdretemohcatlacinahcem
1T1T1T1T1T )02egapees(evirdrotarenegohcat
1M1M1M1M1M redocnesiclElatnemercni
)02egapees()ver / eslup005(
lanoitcerid-inU
1B1B1B1B1B lanoitcerid-iB
4. MRT 7100P - D1 M1 F1 S1 N **
1N1N1N1N1N liolarenimRBN
1F1F1F1F1F laestfahsisp812,RBN
1V1V1V1V1V slaesMPF
1U1U1U1U1U )ekarbrof(laestfahson
5. MRT 7100P - D1 M1 F1 S1 N **
NNNNN )Bnitelni:WCC,Anitelni:WC(noitatordradnats
SSSSS )Anitelni:WCC,Bnitelni:WC(noitatordesrever
7. MRT - 7100P - D1 M1 F1 S1 N **
********** inozlaCnosineDotdevreserecaps8. MRT 7100P - D1 M1 F1 S1 N **
SHAFT
SPEED SENSOR OPTION
SEALS
ROTATION
SPECIAL
TRM TRM TRM TRM TRM suounitnoc.xamisp6263dradnats
ETRM-FTRM ETRM-FTRM ETRM-FTRM ETRM-FTRM ETRM-FTRM suounitnoc.xamisp6403dednapxe
1. MRT 7100P - D1 M1 F1 S1 N **
SERIES
PPPPP
edoc P0017TRM P0017TRM P0017TRM P0017TRM P0017TRM P0087FTRM P0087FTRM P0087FTRM P0087FTRM P0087FTRM P0058ETRM P0058ETRM P0058ETRM P0058ETRM P0058ETRM
ni 3 3.334 5.674 8.915
edoc P0009TRM P0009TRM P0009TRM P0009TRM P0009TRM P0099FTRM P0099FTRM P0099FTRM P0099FTRM P0099FTRM P00801ETRM P00801ETRM P00801ETRM P00801ETRM P00801ETRM
ni 3 5.945 4.406 2.956
QQQQQ
edoc Q00041TRM Q00041TRM Q00041TRM Q00041TRM Q00041TRM Q00551FTRM Q00551FTRM Q00551FTRM Q00551FTRM Q00551FTRM Q00561ETRM Q00561ETRM Q00561ETRM Q00561ETRM Q00561ETRM
ni 3 9.458 3.239 5.9001
edoc Q00071TRM Q00071TRM Q00071TRM Q00071TRM Q00071TRM Q00081FTRM Q00081FTRM Q00081FTRM Q00081FTRM Q00081FTRM Q00591TRM Q00591TRM Q00591TRM Q00591TRM Q00591TRM
ni 3 7.2201 0.0011 5.0911
edoc Q00002ETRM Q00002ETRM Q00002ETRM Q00002ETRM Q00002ETRM Q00512FTRM Q00512FTRM Q00512FTRM Q00512FTRM Q00512FTRM Q00032ETRM Q00032ETRM Q00032ETRM Q00032ETRM Q00032ETRM
ni 3 5.7021 0.8921 6.5041
2. MRT 7100P - D1 M1 F1 S1 N **
SIZE & DISPLACEMENT
1S1S1S1S1S )91-61egapees(cirtemEASdradnats
1G1G1G1G1G )91-61egapees(cirtemisp0006EAS
1M1M1M1M1M )91-61egapees(gnimitlaicepscirtemisp0006EAS
6. MRT 7100P - D1 M1 F1 S1 N **
CONNECTION FLANGE
8/11/2019 Denison Calzoni Type Mrt Mrte Mrtf
http://slidepdf.com/reader/full/denison-calzoni-type-mrt-mrte-mrtf 24/24
SALES AND SERVICE LOCATIONS WORLDWIDE
International Distributors
In Europe :CyprusCzechRepublicGreeceHungaryIcelandJugosavia
NorwayPortugalPolandRomaniaRussiaSlovakiaSloveniaSwitzerlandThe Faroe IslandsTurkey
In Africa :AlgeriaEgyptIvory CoastMorocco
NigeriaSouth AfricaTunisia
In Middle East :BahreinIranIsraelJordanKuwaitLebanonPakistanQatarSaudi ArabiaSyriaUnited Arab Emirates
In Far East :IndonesiaKoreaMalaysiaNewZealandPhilippinesThailand
South-America :ArgentinaBrazilChileColombiaEcuadorMexico
PeruVenezuela
Denison Calzoni S.p.a.Via Caduti di Sabbiuno 15/1740011 Anzola dell’EmiliaBologna ItalyTel: +39 (051) 6501611Fax: +39 (051) 736221e-mail: [email protected]
Asia-Pacific
Australia
Denison Hydraulics PTY41-43 St Hilliers RoadP.O.Box 192Auburn N.S.W. 2144, AustraliaTel : +61 (2) 9646 5200Fax : +61 (2) 9643 1305
Hong Kong
Denison Hydraulics Ltd.Unit 6A, 33/F Cable TV Tower9 Hoi Shing Road, Tsuen WanNT, Hong KongTel : +852 2498 8381Fax : +852 2499 1522
Japan
Denison Japan Inc.4-2-1 Tsujido-ShinmachiFujisawa 251, JapanTel : +81 (466) 35-3050Fax : +81 (466) 35-2019
China
Denison Hydraulics Engineering Ltd.Room 8018, No. 601, ZhangYang
Road Pudong New AreaShanghai 200120, ChinaTel : +86 (21) 58205042 / 58205034Fax : +86 (21) 58205014
Singapore
Denison Hydraulics Sea Pte LTDBlk 5#06-12Ang Mo Kio Industrial Park 2ASingapore 567760Tel : +65 6268 7840Fax : +65 6268 7847
Taiwan
Denison Hydraulics LTD6F-10. No. 79,Sec. 2Roosevelt Road, TaipeiTel : +65 268 7840Fax : +65 268 7847
Europe
Austria
Denison Hydraulics GmbHZweigneiderlassung LinzHaibachstraße 694061 Pasching, AustriaTel : +43 (72 29) 48 87Fax : +43 (72 29) 6 30 92
Benelux
DenisonHydraulics BeneluxB.V.Pascalstraat 1003316 GR Dordrecht, HollandTel : +31 (78) 6179 900Fax : +31 (78) 6175 755
Denmark
DenisonHydraulics DenmarkA/SIndustrikrogen 22635 Ishöj, DenmarkTel : +45 (4371) 15 00Fax : +45 (4371) 15 16
Finland
Denison Lokomec OYPolunmäenkatu 22P.O.Box 11633721 Tampere, FinlandTel : + 358 (3) 3575 100Fax : + 358 (3) 3575 111
France
Denison Hydraulics FranceS.A.14 route du bois blancBP 53918105 Vierzon, Cedex, FranceTel : +33 (2) 48 53 01 20Fax : +33 (2) 48 75 02 91
Great Britain
Denison Hydraulics UK LTDKenmore roadWakefield 41, Industrial ParkWakefield, WF2 OXEWest Yokshire, EnglandTel : +44 (1924) 826 021Fax : +44 (1924) 826 146
Germany
Denison Hydraulik GmbH.Auf dem Sand 14D-40721 Hilden, GermanyTel : +49 (2103) 940 300Fax : +49 (2103) 940 558
Italy
Denison Hydraulics Italy SrlViale Europa 6820090 Cusago (MI), ItalyTel : +39 (02) 90330-1Fax : +39 (02) 90390694/5/6
Denison Calzoni S.p.AVia Caduti di Sabbiuno15/1740011 Anzola dell'Emilia
Bologna, ItalyTel : +39 (051) 6501611Fax : +39 (051) 736221
Spain
Denison Hydraulics S.A.Poligono “La Post”C/ Enginy n°.6, Nave 808850 Gava, Barcelona, SpainTel : +34 (93) 635 5170Fax : +34 (93) 635 5178
Sweden
DenisonHydraulics SvenskaABSporregatan 13213 77 - Malmö, Sweden
Tel : +46 (40) 600 13 00Fax : +46 (40) 600 13 50
North America
Canada
DenisonHydraulics Canada Inc.2880 Brighton Road, Unit 1Oakville, ON L6H 5S3, CanadaTel : +1 (905) 829 5800Fax : +1 (905) 829 5805
Mexico, Central America,South America, Caribbeancountries
Denison Hydraulics Corp.6167 NW 181 Terrace CircleNorthMiami, FL 33015, USATel : +1 (305) 362 2246Fax : +1 (305) 362 2246
USA
Denison Hydraulics Inc.14249 Industrial ParkwayMarysville, OH 43040-9551,USATel : +1 (937) 644 3915Fax : +1 (937) 642 3738
Others
Other European, Middle East,African countries
Denison Hydraulics France S.A14 route du bois blancBP 53918105 Vierzon, FranceTel : +33 (2) 48 53 01 20Fax : +33 (2) 48 53 01 46
Your local Denison Hydraulics representative