District 7020 Foundation Seminar Managing Scholarships and Grants.
DELTA 702x - Slave Readerresource.boschsecurity.com/documents/Data_sheet_enUS_1363584267.pdf ·...
2
Systems | DELTA 702x - Slave Reader This proximity reader with semi-graphic LCD display and backlit silicon keypad is intended for use as a slave reader for connection to access control systems or to terminals for time recording using a slave bus. A MIFARE, HITAG1 or LEGIC non-contact reading module is installed for identification purposes. The connection to the master is established via the RS485 interface. A connection adapter in the surface-mount housing is available as an optional extra. The compact, space-saving design of the terminal means that both surface mounting and flush mounting are possible. Installation/Configuration Notes Installation and assembly • If using the connection adapter (180 x 180 x 91 mm), this should be mounted in the secure area at a maximum distance of 5 m from the reader (ready-made cable supplied with the adapter) • Flush mounting of the terminal in conjunction with flush-mount junction box (double execution advantageous) • Terminal can be surface-mounted with surface-mount housing (order item); can also be used as table-top housing • The terminal should be mounted on the wall in such a way that the user can read the display well and operate the keys easily. Correct ergonomic use is possible at the recommended installation height of approx. 1.5 m. • Type of connection: RJ45, 8-pin for power and system connections • Slanted wall mounting when using surface-mount housing • IP 54, depending on the reader used and correct installation Notes for non-contact readers Please take the following into account when planning and installing non-contact readers to avoid unwanted interference when using non-contact cards and card readers: Non-contact card readers should not be installed behind a metal (conductive) housing or on metal surfaces. See the following list for the required distances: • Distance from metal surfaces at sides at least 30 mm • Distance from 230 V~ power cables and power supplies at least 500 mm • Distance from HF-cables at least 500 mm • Distance from other reader antennas at least 500 mm Particular attention must be paid to the following points when installing the reader: • Check connection of the screen to the data line • Sufficient power supply Reader ranges When the reader is used in optimum conditions, the reader range is as follows, depending on the ID card design: • MIFARE: card up to approx. 40 mm, key fob up to 20 mm • HITAG1: card up to approx. 60 mm, key fob up to 30 mm DELTA 702x - Slave Reader ▶ LCD graphic display ▶ Backlit silicon keypad with 14 keys ▶ Beeper ▶ Housing monitoring contact (tamper detection) ▶ Slanted wall mounting when using surface-mount housing ▶ IP 54, depending on the reader used and correct installation ▶ RS485 L bus interface www.boschsecurity.com
Transcript of DELTA 702x - Slave Readerresource.boschsecurity.com/documents/Data_sheet_enUS_1363584267.pdf ·...
Systems | DELTA 702x - Slave Reader
This proximity reader with semi-graphic LCD display andbacklit silicon keypad is intended for use as a slave readerfor connection to access control systems or to terminals fortime recording using a slave bus. A MIFARE, HITAG1 orLEGIC non-contact reading module is installed foridentification purposes. The connection to the master isestablished via the RS485 interface. A connection adapterin the surface-mount housing is available as an optionalextra. The compact, space-saving design of the terminalmeans that both surface mounting and flush mounting arepossible.
Installation/Configuration Notes
Installation and assembly• If using the connection adapter (180 x 180 x 91 mm),
this should be mounted in the secure area at a maximumdistance of 5 m from the reader (ready-made cablesupplied with the adapter)
• Flush mounting of the terminal in conjunction withflush-mount junction box (double executionadvantageous)
• Terminal can be surface-mounted with surface-mounthousing (order item); can also be used as table-tophousing
• The terminal should be mounted on the wall in such away that the user can read the display well and operatethe keys easily. Correct ergonomic use is possible at therecommended installation height of approx. 1.5 m.
• Type of connection: RJ45, 8-pin for power and systemconnections
• Slanted wall mounting when using surface-mounthousing
• IP 54, depending on the reader used and correctinstallation
Notes for non-contact readersPlease take the following into account when planning andinstalling non-contact readers to avoid unwantedinterference when using non-contact cards and cardreaders:
Non-contact card readers should not be installed behind ametal (conductive) housing or on metal surfaces. See thefollowing list for the required distances:
• Distance from metal surfaces at sides at least 30 mm• Distance from 230 V~ power cables and power supplies
at least 500 mm• Distance from HF-cables at least 500 mm• Distance from other reader antennas at least 500 mmParticular attention must be paid to the following pointswhen installing the reader:
• Check connection of the screen to the data line• Sufficient power supply
Reader rangesWhen the reader is used in optimum conditions, the readerrange is as follows, depending on the ID card design:
• MIFARE: card up to approx. 40 mm, key fob up to 20 mm• HITAG1: card up to approx. 60 mm, key fob up to 30 mm
DELTA 702x - Slave Reader▶ LCD graphic display
▶ Backlit silicon keypad with 14 keys
▶ Beeper
▶ Housing monitoring contact (tamper detection)
▶ Slanted wall mounting when using surface-mounthousing
▶ IP 54, depending on the reader used and correctinstallation
▶ RS485 L bus interface
www.boschsecurity.com
2 | DELTA 702x - Slave Reader
• LEGIC: card up to approx. 60 mm, key fob up to 30 mm
Parts Included
Qty Components
1 Terminal with built-in reader and display (as selected)
1 Installation guide
Technical Specifications
Operation/key-pad
14 keys; backlit silicon keypad
Display Graphic LCD display, 3 lines
Colors Front cover with rear panel: RAL 7035 (light gray)Cover: RAL 7015 (slate gray)
Interface RS485 on RJ-45
Bus protocol L bus protocol
Technical specifi-cations:
Operating temperature range: 0 °C to +60 °C
Dimensions (H x W x D): 180 x 115 x 32 mm
Power supply 12–24 V DC
Standard protection class IP 54.
Power consump-tion
1.6 W
Card reader,optional
Mifare proximity reader
Hitag1 proximity reader
Legic proximity reader
CE compliance Product safety: DIN EN 60950:2001
Interference emission: DIN EN 301 489-3:2001
Interference immunity: EN61000-6-4:2002
Technical modifications reserved
Ordering Information
DELTA 7020 MF RS485 12VWith semi-graphic LCD display, backlit siliconkeypad, serial (RS485) connection and inte-grated Mifare reader.
ARD-7020MF-485
DELTA 7020 HI1 RS485 12VWith semi-graphic LCD display, backlit siliconkeypad, serial (RS485) connection and inte-grated Hitag1 reader.
ARD-7020HI1-485
DELTA 7020 LE RS485 12VWith semi-graphic LCD display, backlit siliconkeypad, serial (RS485) connection and inte-grated LEGIC reader
ARD-7020LE-485
Accessories
DELTA 7020 AS-ADPConnection adapter for Delta 7020 proximityreader to the local power supply of the readerand door opener.
ARA-7020AS-ADP
Americas:Bosch Security Systems, Inc.130 Perinton ParkwayFairport, New York, 14450, USAPhone: +1 800 289 0096Fax: +1 585 223 [email protected]
Europe, Middle East, Africa:Bosch Security Systems B.V.P.O. Box 800025600 JB Eindhoven, The NetherlandsPhone: + 31 40 2577 284Fax: +31 40 2577 [email protected]
Asia-Pacific:Robert Bosch (SEA) Pte Ltd, Security Systems11 Bishan Street 21Singapore 573943Phone: +65 6258 5511Fax: +65 6571 [email protected]
Represented by
© Bosch Security Systems Inc. 2010 | Data subject to change without noticeT2193756427 | Cur: en-US, V11, 4 Jul 2010 | Src: de-DE, V1, 29 Mar 2007
