RemyDecorative (Cement)

Photo features 8"x8" Remy in Brigette on Niche, 12"x24" Iceberg White Marble Field Tile on Wall and 8"x36" Distressed Field Tile in Taurus on Floor.

Remy Decorative (Cement)

8"x8" Solid Field Tile - Matte

Snow - SNODECREMSNO88

Wedgewood Blue - WEBDECREMWEB88

Cobalt - COBDECREMCOB88

Fog - FOGDECREMFOG88

Smoke - SMODECREMSMO88

Charcoal - CHADECREMCHA88

8"x8" Pattern Field Tile - Matte

Oasis - OASDECREMOAS88

Damsel - DAMDECREMDAM88

Soffia - SOFDECREMSOF88

Frame - FRADECREMFRA88

Darcy - DARDECREMDAR88

Nouveaux - NOUDECREMNOU88

Remix - REMDECREMREM88

Brigette - BRIDECREMBRI88

Use only non-sanded grout with this product.

Tiles must be sealed prior to grouting to prevent penetration. Miracle Sealants 511 Porous Plus sealer is recommended before and after grouting. Tiles must dry for at least 24 hours before grouting. Any excess grout must be wiped from the surface of the tiles immediately and meticulously. Other options for post-grouting sealants include DryTreat Stain-Proof solvent-based sealer (does not enhance tile color) or DryTreat Intensif ia non-solvent based sealer (enhances the tile color). Exterior installation requires re-sealing every 2-3 years.

Dark grouts are not recommended with light tiles. Light grouts are not recommended with dark tiles. All spills must be cleaned immediately to prevent staining. These tiles are handmade and subject to color variation. Mix randomly from dif ferent boxes to balance variation. Wet the back of the tile prior to setting. Apply thinset to both the substrate and the back of the tile using a notched trowel. The tile pattern displays best with 1/16" to 1/8" grout joints. Wider joints are necessary in wet areas or when using floor heating cables.

Images and product samples are representative of a product’s potential characteristics. There is no guarantee that the sample product or images will 100% match the product received. Field, mosaic, and trim tile may not be an exact match. Tiles are subject to variations in color, shade, size, surface texture and finish. Prior to installation, installer must blend tiles from several dif ferent boxes to achieve an even distribution of color range. Installer must conduct a dry mock layout under proper lighting conditions prior to installation. It is the consumer’s responsibility to inspect the product prior to installation to ensure satisfaction. Once installed, the product is deemed accepted. Check Manufacturer's specifications as some Mosaic tiles may not be appropriate for wet applications. Reference the most current TCNA Handbook, ANSI, Manufacturer's specifications, and Bedrosians Care & Maintenance guide for installation, outdoor use, care and maintenance information. Improper installation, application, use, care and maintenance voids warranty. We reserve the right to make changes to product specifications at any time without notice. Please visitwww.bedrosians.com for current product information.

APPLICATIONS

Commercial

Light Commercial

Residential

Floors Walls Countertops Shower Floors Shower Walls Pools/Spas

††

Applications & ANSI Technical Specifications do not apply

Product rated for Interior & Exterior use Product rated for Interior use only

Special Order only*

LEGEND

May be suitable for Exterior Floors†

Type Shape Item Code Size Description Pcs / Ctn Sf / Ctn

Solids DECREMCHA88 8"x8"x5/8" Charcoal - Field Tile - Matte 12 5.33

DECREMCOB88 8"x8"x5/8" Cobalt - Field Tile - Matte 12 5.33

DECREMFOG88 8"x8"x5/8" Fog - Field Tile - Matte 12 5.33

DECREMSMO88 8"x8"x5/8" Smoke - Field Tile - Matte 12 5.33

DECREMSNO88 8"x8"x5/8" Snow - Field Tile - Matte 12 5.33

DECREMWEB88 8"x8"x5/8" Wedgewood Blue - Field Tile - Matte 12 5.33

Patterns DECREMBRI88 8"x8"x5/8" Brigette - Field Tile - Matte 12 5.33

DECREMDAM88 8"x8"x5/8" Damsel - Field Tile - Matte 12 5.33

DECREMDAR88 8"x8"x5/8" Darcy - Field Tile - Matte 12 5.33

DECREMFRA88 8"x8"x5/8" Frame - Field Tile - Matte 12 5.33

DECREMNOU88 8"x8"x5/8" Nouveaux - Field Tile - Matte 12 5.33

DECREMOAS88 8"x8"x5/8" Oasis - Field Tile - Matte 12 5.33

DECREMREM88 8"x8"x5/8" Remix - Field Tile - Matte 12 5.33

DECREMSOF88 8"x8"x5/8" Soffia - Field Tile - Matte 12 5.33

SIZING & PACKAGING

Shade Variation

V2-Slight

V1 V3 V4

DCOFAcutest

ScratchResistance

MOHS

BreakingStrength

ASTM# C648

WaterAbsorption

ASTM# C373

ChemicalResistance

ASTM# C650

BondStrength

A137.2-7.7

ThermalShock

ASTM# C484

Results ≥ 0.42 N/A N/A > 7.0 (Concrete) Unaffected N/A N/A

ANSI TECHNICAL SPECIFICATIONS

REV. 12/2017MKTTERDECREM

††

When properly installed and maintained, cement tiles can be enjoyed for many years. Please be sure to familiarize yourself and the installer with these instructions prior to starting the job. You and your installer are responsible for ensuring proper installation and sealing of the tiles. If you have any questions, contact productwarranty@bedrosians.com before moving forward.

CEMENT TILE

RECOMMENDED INSTALLATION PRODUCTS & TOOLS

RECOMMENDED ADHESIVESA high quality, medium-bed mortar is recommended. White mortar is commonly recommended. Avoid using setting materials from different production batches and check for bag-to-bag color consistency. Cement tiles are not intended for installation methods employing large quantities of water.

1. ARDEX X 5™ Flexible Tile and Stone Mortar 2. LATICRETE® 4-XLT

3. BOSTIK Single Flex

RECOMMENDED SEALERSCement tiles are not pre-sealed at the factory. Therefore, use of an impregnating or penetrating sealer specifically designed for porous materials must be applied to the tiles prior to installation and post-grouting.Cement tiles must be sealed twice: pre-installation and post-grouting.

1. Miracle Sealants 511 Porous Plus- recommended for pre-installation and post-grouting. 2. Drytreat STAIN-PROOF - recommended only for post-grouting. a. This sealer is specifically for stain proofing. It is a solvent base and does not enhance the color of the tiles. 3. Drytreat Intensifia - recommended only for post-grouting. a. This sealer is specifically for enhancing color, it is not a solvent although it does provide stain proofing.

RECOMMENDED GROUTSWe advise against using dark colored grout with light-colored tiles and vice versa. Grout can stain the tiles and be difficult to remove so be sure the grout matches the color of the cement tile as closely as possible.

RECOMMENDED EDGE PROTECTIONThis edge treatment may be used in replacement of bullnose or trim. 1. Schluter 11/16" edge treatment

RECOMMENDED WET SAW CUTTING BLADES 1. Alpha 10" Porcelana Blade #PT101A+-Continuous Rim (TLSPT10A); or 2. BCE 10" Supreme Granite/Porcelain Blade-Continuous Rim (BCEDB10POR)

PREPARATION AND INSTALLATION INSTRUCTIONS

STORAGEDo not allow the boxes to get wet! Store the material in a dry area. Moisture or dampness can cause staining, fading, or effervescence causing a white powdery effect on the surface of the tile. If installing cement tiles inside, allow the tiles to season in their final environment prior to installation.

CUTTING Be sure not to damage the finished surface or corners of the tile. Use a sharp diamond blade in conjunction with water to avoid chipping of edges. Do not push the tiles through; let them move naturally through the blade. Use recommended cutting tools referenced above.

APPLICATIONThese encaustic cement tiles may be installed in many different applications. They are not recommended for pools/spas or exterior Commercial floors.

SUBSTRATEPursuant to the TCNA, for tile installations, special attention should be given to substrate stability, rigidity and preparation. Substrates should be sufficiently flat to allow uniform coverage and avoid excessive mortar thickness. Clean the surface well to remove all dirt and residue and remediate all cracks or unleveled areas in the substrate to ensure it is smooth and flat prior to installation. Install over a cured concrete surface or suitable sub-floor like Hardibacker or Ditra. Wall installation on drywall is acceptable when installed with appropriate non-sag setting materials.

INSTALLATIONPlease see the latest edition of the TCNA Handbook for further instruction.

1. Prior to installation and any cutting, inspect your order carefully. Cement tile is subject to color and tonal variations and it is strongly recommended to blend tiles from different boxes to achieve a uniform effect. 2. Clean the tiles prior to sealing. Only use a pH neutral cleaner; do not use any acids or alkalines to clean the tiles. Ensure the tiles are thoroughly dry prior to sealing.

INSTALLATION,

CARE &

MAINTENANCE

INSTRUCTIONS

INSTALLATION (CONT.)

3. Then seal tiles using one of the above-referenced impregnating

or penetrating sealers prior to installation. Apply the sealer

in thin layers until the tiles will not soak up any more. Wipe off

any excess sealer before it dries and allow the sealer to cure

and the tiles to dry for at least 24-48 hours prior to installation.

Follow sealer manufacturer’s instructions. When properly sealed,

water should bead on the surface of the tile.

4. Before laying the tiles in thinset, wipe the back of the tiles with

a damp sponge to remove any concrete dust residue and

enable proper adhesion.

5. Installer must conduct a dry mock layout under proper lighting

conditions prior to installation by placing glass tiles on the

floor for quality and color inspection. It is imperative that the

end user inspect the product prior to installation. Once

installed, the product is deemed accepted.

6. Installer must blend/mix tiles from several different boxes

to achieve an even distribution of color range. These tiles are

handmade and subject to color variation so it is imperative that

this step is not skipped.

7. Mark out grid lines on the surface to be tiled.

8. The recommended grout joint is 1/16" to 1/8". Wider joints may

be necessary in wet areas or when using floor heating cables.

If using spacers, use a soft, flexible spacer.

9. Key in thin-set over the substrate with the flat side of a trowel.

Use a ½" x ½" square-notched trowel at a 45° angle to spread

the adhesive evenly over the substrate in straight lines.

10. Use the flat side of the trowel to back-butter the tile. Ensure

the mortar adhesive is applied to the full back of each tile

(100% coverage).

11. Set the tiles into the adhesive according to the marked

gridlines, starting from one end and continuing to the other.

Do not use a mallet to level the tiles as this may cause the tiles

to crack or weaken.

12. Tiles are fully embedded when the thin-set is 1/3 the

depth of the tile.

13. Immediately remove any excess adhesive from the surface

with a damp cloth or sponge. Do not wait to do this.

14. Wait the thin-set manufacturer’s instructed time

before grouting.

GROUTING

Please see the latest edition of the TCNA Handbook for further

instruction.

1. Once the thinset has cured, spread non-sanded grout with a

rubber float, completely filling the joints. Joints should be full

and free of voids and pits.

2. Grout should be applied to small areas at a time so that any

excess grout on the face of the tiles is wiped off immediately

using a damp and clean sponge. Remove any liquid residue

with a clean dry cloth. Do NOT spread grout over the entire

floor like you would for porcelain or ceramic tile. Grout that sits

too long can be difficult to remove from the tile. Do not affix

duct tape, gaffer tape or acid tape directly onto the surface of

the cement tiles as it can discolor or stain your cement tiles.

3. Rub all joints to ensure even levels of grout within each joint.

4. Before the grout dries, remove any liquid residue with a clean

dry cloth. Do not allow water or other liquids to spot, pond

or ring on the surface. Do not leave spillages, drips, wet

buckets, cups, footmarks, etc. on the surface at any time. POST-GROUTING

1. At least 24-48 hours after grouting, and only after the tiles

and grout are completely dry, seal the clean tiles again. Please

see above for recommended impregnating or penetrating

sealers to use post-grouting. Follow sealer manufacturer’s

instructions.

2. Once the sealer has cured and dried, cover the tile

immediately with a protective covering to prevent staining and

damage during the remainder of construction.

CARE AND MAINTENANCE INSTRUCTIONS

ROUTINE CLEANINGSpecific cleaning and maintenance requirements vary depending on the tile’s surface and texture and any present contaminants. Below are some general cleaning and maintenance guidelines.

1. For ongoing maintenance, clean the tiles regularly with a pH neutral cleaner and buff the tiles with a white pad. A natural patina will occur as the floor is maintained and experiences natural wear. 2. Soap-based detergents may be used, or diluted soft soap if available in your market. Repeated cleaning with soft soap will also help maintain a satin finish to the tiles, and to an extent, acts as a continuous re-sealant. 3. If a cleaning solution other than water is utilized, use only a neutral, non-abrasive and non-acidic cleaner. Avoid use of any harsh cleaning products that contain bleach or acidic chemicals. Avoid the use or placement of anything acidic on these tiles. 4. It is important that the cleaner is a non-oil, non-soap and non-animal fat based product. These products act like a magnet, attracting dirt and dust. 5. Always test cleaning solutions on a small inconspicuous area before proceeding to clean the entire surface area. 6. Spills must be cleaned immediately to prevent staining. 7. Use of properly sized walk-off mats at entrances and sweeping or dust mopping is important to remove abrasive grit. 8. Surface stains can be buffed out by lightly using a 220 or 400 grit sandpaper along with white vinegar. 9. For hard to remove residue, a single disc floor machine with a white pad may be used. Be sure to wet the surface first when using a floor machine and clean any residue immediately.

RESEALINGOutdoor or high foot traffic installations must be re-sealed every 2-3 years.

PLEASE NOTE

If you have any questions, contact productwarranty@bedrosians.com before cutting or installing tiles. Please visit Bedrosians.com for full product details and approved applications. Reference the most current ANSI and TCNA Handbooks for current industry installation standards. Improper installation, care and/or maintenance voids warranty.

Customer’s selection and use of Bedrosians® products and the installation procedures and maintenance practices employed by each customer are outside the direction and control of Bedrosians® and are strictly and completely the choice and responsibility of each customer and their installer. Bedrosians® does not warrantee product for any specific use, nor any installation procedure or maintenance practice, and expressly disclaims all asserted claims after installation of Bedrosians® products. Bedrosians® will not be held responsible for improper installation of your tile or specific jobsite conditions.

PROLONG

THE BEAUTY

OF YOUR

CEMENT TILE