DATA SHEET: TEMBREAK 2 S250-GE MCCB - Terasaki...GE 40 125 160 250 690-800 8 7.5 25 50 65 85-7.5 25...
4
TB2 S/H/L 250 S250 3,4 GE 40 125 160 250 690 - 800 8 7.5 25 50 65 85 - 7.5 25 25 36 85 - 25 65 165 105 140 103 2.3 3.1 250 Max. rating 200A for Plug-in DATA SHEET: TEMBREAK 2 S250-GE MCCB MCCB Electrical Characteristics to IEC 60947-2, EN 60947-2, JIS C 8201-2-1 ANN.1, AS/NZS 3947-2, NEMA AB-1
Transcript of DATA SHEET: TEMBREAK 2 S250-GE MCCB - Terasaki...GE 40 125 160 250 690-800 8 7.5 25 50 65 85-7.5 25...
TB2 S/H/L 250
S2503,4GE
40125160250
690-8008
7.525506585-
7.525253685-
2565
1651051401032.33.1
250
Max. rating 200A for Plug-in
DATA SHEET: TEMBREAK 2 S250-GE MCCB
MCCB Electrical Characteristics to IEC 60947-2, EN 60947-2, JIS C 8201-2-1 ANN.1, AS/NZS 3947-2, NEMA AB-1
With extension bars (optional)
Front connected
Rear connected
Front connected with Motor Operator
Rear connected with Motor Operator
Panel cutout dimensions shown give an allowance of 1.0mm or more around the handle escutcheon.
48
DATA SHEET: TEMBREAK 2 S250-GE MCCB Outline Dimensions S250-GEASL: Arrangement Standard Line HL: Handle Frame Centre Line
Page 2 of 4
9
6 (max.)
15.5 (max.)
Preperation of conductor
22 (max.)
Mounting on a support or rails (shown with optional connection bars oriented for rear access)
Mounting through the backplate (shown with optional connection bars oriented for rear access)
Mounting on the backplate (optional connection bars must be oriented for front access)
Mounting screwM8x18 max.
45
4
27
102
42
88
116
172
4t4t
165
132
96
136
156
76.5
M5x20Mounting screw
Mounting plate
45
96
102
22
160
4t
2020
165
179
203
1834
122
Insulating plate
Mounting screw M5 NUT
Insulating plate
Mounting plate
Support or rail
Support or rail
Termination of BusbarOutline Dimensions
ASL: Arrangement Standard Line HL: Handle Frame Centre Line
DATA SHEET: TEMBREAK 2 S250-GE MCCB
Outline Dimensions S250-GE Plug-in Version
Page 3 of 4
Trip
ping
Tim
e
Percent Rated Current IR
In = 250A; 160A; 125A; 40A Note(1)
LT
ST
PTA
NPOption
Standard
IR (A)LTD Pick-up current IR xIn 0.4 0.5 0.63 0.8 0.9 0.95 1.0
1Characteristics
Note(1) For Plug-in (PM), max. setting for IR should be less than 225A. When In=250A, IR should be In�0.9 or less.(2) Ii max. = 13 x In. (3) Characteristic of neutral protection (tN vs. IN) is identical to characteristic of phase protection (tR vs. IR).
No. 2 4 511
2.5 5 100.20.1
14(Max: 13 x In) Note (2)0.840
1.0 Note (3)tN = tRtN
IN
tpIp
Ii
tsd
Isd xIR
xIRxIR
xIR
(s)
(s)
(s)
tR (s)at 200% x IR at 600% x IR
21 21 5 7.5
INST
3
Time/Current Characteristic Curves
S250-GE
Page 4 of 4
DATA SHEET: TEMBREAK 2 S250-GE MCCB
