DATA SHEET: TEMBREAK 2 S160-SDN - Terasaki Lite... · Outline Dimensions S160-SDN CL CL CL C LC C...
2
TB2 Lite 160 (A) (V) (V) (kV) (kA peak) (kA rms) (mm) (mm) (mm) (kg) cycles cycles DC AC 50/60 Hz 0.3 seconds DC 3 pole 4 pole 3 pole 4 pole 1000V DC 800V DC 600V DC SDN 160 600 690 8 2 2 DC-22A • • - • 130 75 - 68 0.8 - • • - - - 1,000 7,000 I n U e U i U imp I cm I cw height width depth weight Electrical Mechanical Standard • Optional - Not Available Electrical Characteristics to IEC 60947-3, EN 60947-3, JIS C 8201-3 Quantity Unit Condition 160 S160 3 Max In (A) of Frame Model Number of Poles Type Nominal current ratings Electrical characteristics Rated operational voltage Rated insulation voltage Rated impulse voltage Rated short circuit making capacity Rated short-time withstand current Utilisation category to IEC 60947-3 Installation Front connection (FC) Extension bar (FB) Rear connection (RC) Plug-in (PM) DIN rail mounting (DA) Dimensions Weight Operation Direct Opening Action Toggle operation Breaker mounted handle (HB) Door mounted (HS) Motor operation Endurance DATA SHEET: TEMBREAK 2 S160-SDN FOR USE ABOVE 250V DC Page 1 of 2 Frame reference
Transcript of DATA SHEET: TEMBREAK 2 S160-SDN - Terasaki Lite... · Outline Dimensions S160-SDN CL CL CL C LC C...
TB2 Lite 160
(A)
(V)(V)(kV)
(kA peak)(kA rms)
(mm)(mm)
(mm)
(kg)
cycles
cycles
DCAC 50/60 Hz
0.3 secondsDC
3 pole4 pole
3 pole4 pole
1000V DC800V DC600V DC
SDN
160
6006908
22
DC-22A
••-•
13075-
68
0.8-
••-
--
1,0007,000
In
UeU i
U imp
IcmIcw
heightwidth
depth
weight
Electrical
Mechanical
Standard • Optional - Not Available
Switch Disconnector Electrical Characteristics to IEC 60947-3, EN 60947-3, JIS C 8201-3 Quantity Unit Condition
160S160
3
Max In (A) of Frame
ModelNumber of PolesType
Nominal current ratings
Electrical characteristics
Rated operational voltage Rated insulation voltageRated impulse voltage
Rated short circuit making capacityRated short-time withstand currentUtilisation category to IEC 60947-3
Installation
Front connection (FC)Extension bar (FB)Rear connection (RC)Plug-in (PM)DIN rail mounting (DA)Dimensions
Weight
Operation
Direct Opening ActionToggle operationBreaker mounted handle (HB)Door mounted (HS)Motor operation
Endurance
DATA SHEET: TEMBREAK 2 S160-SDN SWITCH DISCONNECTOR FOR USE ABOVE 250V DC
Page 1 of 2
Frame reference
Outline Dimensions S160-SDN
CL CL
CL
CL CL CL
HL
L
HL
HL
HL
H
4P
4P
CL260
214
228
116
110
37.68
45
45 4570 115
51
45
18530
14.5
44.5
ø14
36.68
60 60 60126.581.5
14.5
30 44.5
349
260
118
92
R6
36.598.6
108.64
90102
104.6
228
260
830
ø13
129.1
30 45 45 45
103
11070
153915
39
214
45
228
45 45 45
88
ø36
ø13
52.5
1.6t
86.9
100
98.6
108.64104.6
90102
13.1
129.1146.6
25(max.)12
ø11
(max
.)
1.6t
146.6
)weiv tnorf( tuotuc lenaP)weiv tnorf( nalp gnillirD
Preparation of conductor With extension bars (optional) Drilling plan (front view)Front connected
Rear connected
Con
duct
or
over
lap,
max
Con
duct
or
over
lap,
max
Stud can be turned 45° or 90°
M6Tapped hole
M6Tapped hole
Mounting plateInsulation plate
Interpole barrier(removable)
Interpole barrier
Mounting hole
Insulation plate
Panel cutout dimensions shown give an allowance of 1.0mm around the handle escutcheon.Note: Studs are factory installed in horizontal direction both on the line and load sides.
ON side : 37.6OFF side : 36.6
Groove for dissipating heat generated by overcurrent
Trip button (red)
M10 screw
M6Mounting screw
ASL: Arrangement Standard Line HL: Handle Frame Centre Line
Page 2 of 2
DATA SHEET: TEMBREAK 2 S160-SDN SWITCH DISCONNECTOR FOR USE ABOVE 250V DC
