8/10/2019 Daily Activity HMI Upgrade TEG 9610-9620 Per November 5,2014

1/11

PT.Indoturbine GENERAL REPORTDistributor Of Solar Turbines

FIELD REP Report Dates

Andika Pratama

Yusup Armansyah November, 2014

Country Customer Name Site Name CSA Numbers

INDONESIA TOTAL E&P NPU Site

PD

Number

Customer

Tag

Package

S/N

Engine

S/N

Package

Starts

Package

Hours

Engine

Hours

Service Order

No.

70231

70232

TEG 9610

TEG 9620

CG01823

CG01824 1072H

PT. Indoturbine 1/11

HMI UPGRADE PROJECT

TEG 9610 & TEG 9620

8/10/2019 Daily Activity HMI Upgrade TEG 9610-9620 Per November 5,2014

2/11

SITE VISIT REPORT FSR NAME

Andika Pratama

Yusup Armansyah

PT.Indoturbine 2/11

PT. IndoturbineDistributor of Solar Turbines

I. Purpose of visit

The purpose of visit is Technical Services for HMI Upgrade Centaur 50 (TEG 9610 & 9620) at NPU -

Total E&P Indonesie

II. Engine Specification:

Package Name Plate TEG 9610 & TEG 9620

Console Name Plate TEG 9610 & TEG 9620

Engine Name Plate TEG 9610 & TEG 9620

8/10/2019 Daily Activity HMI Upgrade TEG 9610-9620 Per November 5,2014

3/11

SITE VISIT REPORT FSR NAME

Andika Pratama

Yusup Armansyah

PT.Indoturbine 3/11

PT. IndoturbineDistributor of Solar Turbines

4 November, 2014

Trip from Balikpapan to Handil, prepare Hand Tools requirement

5 November, 2014

Trip from Handil to NPU Site

Pre Job Meeting with Control System team Total E&P

Check aviability for parts order

Functional verification Software HMI and accessories as per procedure

6 November, 2014

Pre Job Meeting with Control System Total E&P

Dismantle old HMI Configuration TEG 9610 Set up new configuration for TEG 9610

Meachining plat and make a hole to fitting the HMI display with TCP panel

Put new Cable Tag as per customer request

Verified Communication line between PLC and HMI working properly

7 November, 2014

Pre Job Meeting with Project Engineer and Control System Total E&P

Programming additional rung PLC 5 as per mandatory for Upgrade new HMI

Start to SAT Check functional test for communication throught existing PLC program for TEG 9610

8 November, 2014

Pre Job Meeting with Project Engineer and Control System Total E&P

Continue Commisioning Functional Test with Instrument Team

Commisioning done, continue with Start Engine as per sequence

9 November, 2014

Pre Job Meeting with Project Engineer and Control System Total E&P

Give a short training for new navigation HMI TT4000 ver 5 as per Customer request

Completed Handover Document and Dosier

Punch List pending per 9 November

Provide DB-25 angel connector

Update Drawing 70231-149480 as per new configuration

Provide antivirus McAfee (customer request) for TEG 9610 & TEG 9620

10 November, 2014

Trip to Balikpapan from Handil

8/10/2019 Daily Activity HMI Upgrade TEG 9610-9620 Per November 5,2014

4/11

SITE VISIT REPORT FSR NAME

Andika Pratama

Yusup Armansyah

PT.Indoturbine 4/11

PT. IndoturbineDistributor of Solar Turbines

Attached Pictures during the project

Configure PLC5 with new PLC5 program due to

mandotory Solar Inc. For upgrade HMI Verified all parts working properly.

Install New Operating System due to Serial Package

Number and OS License on HMI Hardware.

New HMI Display as per Solar Package

8/10/2019 Daily Activity HMI Upgrade TEG 9610-9620 Per November 5,2014

5/11

SITE VISIT REPORT FSR NAME

Andika Pratama

Yusup Armansyah

PT.Indoturbine 5/11

PT. IndoturbineDistributor of Solar Turbines

Short training for change mode to start produsction

mode or configuration mode

Perform SAT for TEG 9610 as per procedure

Configure TCP TEG 9610

Check and verify all function of existing system for

new HMI Display

Check all existing parts working prperly before HMI system installed on panel

8/10/2019 Daily Activity HMI Upgrade TEG 9610-9620 Per November 5,2014

6/11

SITE VISIT REPORT FSR NAME

Andika Pratama

Yusup Armansyah

PT.Indoturbine 6/11

PT. IndoturbineDistributor of Solar Turbines

Perform Commissioning as per procedure. Give a short training for operating new HMI with TT4000 ver 5

procedure

New wire configuration on TCP TEG 9610 for new HMI display with TT4000 ver 5

Handover Document & Dosier (a)

Handover Document & Dosier (b)

8/10/2019 Daily Activity HMI Upgrade TEG 9610-9620 Per November 5,2014

7/11

SITE VISIT REPORT FSR NAME

Andika Pratama

Yusup Armansyah

PT.Indoturbine 7/11

PT. IndoturbineDistributor of Solar Turbines

Handover Document & Dosier (c)

Found new program on HMI TT4000 ver 5 start crank button fuction visibilty was disable. Change with

new configuration to perform proper function due to PLC5 program.

Found new program on HMI TT4000 ver 5 stop crank button fuction visibilty was disable. Change with

new configuration to perform proper function due to PLC5 program.

8/10/2019 Daily Activity HMI Upgrade TEG 9610-9620 Per November 5,2014

8/11

SITE VISIT REPORT FSR NAME

Andika Pratama

Yusup Armansyah

PT.Indoturbine 8/11

PT. IndoturbineDistributor of Solar Turbines

Added 3 New Rung on Ladder 2 rung 2,3,4

Before change logix on ladder 11 rung 1

8/10/2019 Daily Activity HMI Upgrade TEG 9610-9620 Per November 5,2014

9/11

SITE VISIT REPORT FSR NAME

Andika Pratama

Yusup Armansyah

PT.Indoturbine 9/11

PT. IndoturbineDistributor of Solar Turbines

After change logix on ladder 11 rung 1

Added Logix and make new rung on ladder 11 rung 26

8/10/2019 Daily Activity HMI Upgrade TEG 9610-9620 Per November 5,2014

10/11

SITE VISIT REPORT FSR NAME

Andika Pratama

Yusup Armansyah

PT.Indoturbine 10/11

PT. IndoturbineDistributor of Solar Turbines

Added Logix and make new rung on ladder 11 rung 26 and change addres

Add rung and logix on ladder 143 last rung

8/10/2019 Daily Activity HMI Upgrade TEG 9610-9620 Per November 5,2014

11/11

SITE VISIT REPORT FSR NAME

Andika Pratama

Yusup Armansyah

PT.Indoturbine 11/11

PT. IndoturbineDistributor of Solar Turbines

ladder 34 still exist should be remove