D9032 Encoder SDI Board Install

7/31/2019 D9032 Encoder SDI Board Install

1/16

Installation Instructions forInstalling the Advanced Video InputBoard in a D9032 Encoder

Overview

Audience

These installation instructions apply to trained Cisco service personnel who want to

install an Advanced Video Input Board in a D9032 Encoder.

Introduction

Installation of the Advanced Video Input Board must only be performed by trainedCisco service personnel. Contact your local Cisco sales office for further informationon how to get your D9032 Encoder(s) upgraded.

Document Version

This is the third release of these installation instructions.

In This Document

General ...................................................................................................................................... 2AVIB Upgrade Kit ................................................................................................................ 2Software Upgrade Kit........................................................................................................... 2Before You Start .................................................................................................................... 3

Upgrading the Software .......................................................................................................... 4To Upgrade the Software ..................................................................................................... 4

Removing the Top Plate .......................................................................................................... 5Removing Modules .................................................................................................................. 6Inserting the Modules ............................................................................................................. 9

Installing the Advanced Video Input Board ..................................................................... 9Reinstalling the Dual Audio Module (If Present) .......................................................... 12Installing the Advanced Video Input, SDI Option ............................................................ 13

To Install the Advanced Video Input, SDI Option ......................................................... 13For Information ...................................................................................................................... 14


2/16

2 4015277 Rev C

General

GeneralWARNING:

Allow only Cisco service personnel to open the unit. Otherwise, personal

injury or equipment damage may occur.

CAUTION:

The unit contains electrostatic discharge (ESD) sensitive components.Observe the following rule:Do not attempt to open a unit without proper precautions againstelectrostatic discharge, i.e. use a wrist strap and conductive work-benchsurface. Reason: The unit may fail or be degraded

AVIB Upgrade Kit

The parts required for installing the Advanced Video Input Board are supplied inthe following kit:

Item Part Number

Kit, Advanced Video Input Board, AVIB 4015092

Software Upgrade Kit

The Advanced Video Input Board requires a D9032 Encoder software version v02.06or greater. This can be ordered as a software upgrade kit:

Item Part Number

D9032 Encoder, software upgrade kit 4015939

Advanced Video Input, SDI Option

The Advanced Video Input Board has an SDI option which can be enabled byinstalling a license file. The Advanced Video Input, SDI option can be ordered as anadd-on product to the Advanced Video Input Board:

Item Part Number

Advanced Video Input, SDI Option 4015093


3/16

4015277 Rev C 3

General

Before You Start

You need the following tools and accessory:

Item

Screwdriver, PH-1

Flat bladed screwdriver

Internal hex wrench, 5 mm

Sechskant-Rohr-Steckschlssel 13 mm aus Stahlrohr (Hex-end tubewrench, 13 mm) Manufacturer: Hahn+Kolb part number 52174130. Can bebought fromwww.mercateo.com.
http://www.mercato.com/http://www.mercato.com/http://www.mercato.com/http://www.mercato.com/


4/16

4 4015277 Rev C

Upgrading the Software

Upgrading the Software

To Upgrade the Software

Important: The Advanced Video Input Board requires a software version v02.06 orgreater.

Perform the following steps to upgrade the software to version v02.06 or greater:

1. Power up the unit and connect it to a PC via an Ethernet LAN.

2. Enter the GUI by typing the units IP address in the Internet Explorer address field.

3. From the user interface of the D9032 Encoder click the System tab and the Systemicon from the sub-pages.

4. Store the old setting files before upgrading to a new software version.

This enables you to restore your settings if you need to downgrade5. Click the Upgrade button.

6. Browse to the appl.pkg file and click Transfer.

Note: It may take several minutes to upgrade the software for all 4 modules.

Important: Due to a restriction in the MS Internet Explorer the path of the softwarepackage file (appl.pkg) should be less than 50 characters long.


5/16

4015277 Rev C 5

Removing the Top Plate

Removing the Top PlatePerform the following steps to remove the top plate of the D9032 Encoder:

1. Switch off the power to the D9032 Encoder. Remove the power cord.

Dismount the Encoder from the rack.

2. Unscrew the 8 screws holding the top plate.


6/16

6 4015277 Rev C

Removing Modules

Removing ModulesPerform the following steps to remove the modules from the unit:

1. Note the location of the various modules in the drawing below.

SDI INPUT (4009245)

Dual Audio (4006569)

Composite Video (4010240)

2. Unscrew the screws holding the SDI, Composite and Dual Audio modules.

3. Remove the plastic washers for the SDI and Composite video modules.

4. Unplug the coax cable from the SDI module and loosen it from the 2 clamps.


7/16

4015277 Rev C 7

Removing Modules

5. Remove the SDI, Composite and Dual Audio module, if present.

Note: The audio module must be removed in order to replace the BNC cable for theSDI input.

Insert a flat bladed screw driver in the odd shaped holes in the sides of the chassisand carefully loosen the modules little by little.

You do this by inserting the screwdriver under the module.

Important: Only insert a few millimeters in order not to damage the components onthe boards.

Take care to lift the module equally by switching the position of the screwdriver fromone end of the module to the other.


8/16

8 4015277 Rev C

Removing Modules

6. Unscrew the BNC from the rear panel and remove the coax cable.

This is done by cutting the cable holding the internal connector and unscrewing thenut key using a hex-end tube wrench (13 mm).

Important: Be careful not to scratch the board with the screwdriver when unscrewing

the nut with the wrench.


9/16

4015277 Rev C 9

Inserting the Modules


Installing the Advanced Video Input Board

Perform the following steps to install the Advanced Video Input Board in the D9032Encoder:

1. Note the location of the various modules, coax cable (4012556) and Cable SAD ADH4x3 (3989827) in the drawing below.

AVIB (4013267)

3989827 4012556

Dual Audio (4006569)


10/16

10 4015277 Rev C


2. Mount the BNC cable in the D-shaped hole in the rear panel.

3. Use the hex-shaped 13 mm tube wrench and a screwdriver to tighten the nut.

Important: Be careful not to scratch the board with the screwdriver when tighteningthe nut with the wrench.


11/16

4015277 Rev C 11


4. Inspect the connectors on the main board for bent pins. Straighten any bent pinsbefore inserting the Advanced Video Input module.

5. Position the Advanced Video Input module (4013267). Be very careful when pressingthe board into the connectors and make sure that the connectors are mating.

6. Secure with 4 screws (3984307) Tighten to torque = 0,7 Nm

7. Connect the coax cable (4012556) to the Advanced Video Input module and fixatewith one CABLE SAD ADH 4X3 (3989827).


12/16

12 4015277 Rev C


Reinstalling the Dual Audio Module (If Present)Proceed as follows to reinstall the Dual Audio Module:

1. Inspect the connectors on the main board for bent pins. If there are bent pins

straighten them before inserting the Dual Audio Module.2. Mount the board into the connectors make sure that the connectors are mating.

Secure with 4 screws (part number 3984307).


13/16

4015277 Rev C 13

Installing the License File for the Advanced Video Input,SDI Option

To Install the License File for the Advanced Video Input, SDI Option

The below procedure is only relevant if you have bought the Advanced Video Input,SDI Option, part number 4015093.

Perform the following steps to install the license file for the Advanced Video Input,SDI Option:

1. Power up the unit and connect it to a PC via an Ethernet LAN.

2. Enter the GUI by typing the units IP address in the Internet Explorer address field.

3. Insert the CD ROM from the license kit in the CD ROM drive.

4. Click the Options License icon from the System tab in the GUI.

5. Click the Install button.

6. Browse for the license file on the supplied CD ROM drive and click Open.

Loading takes approximately 10 seconds. The option is installed in your Encoder.Check that the text in the Installation Status column changes from Not Installed toInstalled and the Status column from Disabled to Enabled.

7. Click Apply.


14/16

14 4015277 Rev C

Installing the License File for the Advanced Video Input, SDI Option

For Information

If You Have Questions

If you have technical questions, call Cisco Services for assistance. Follow the menuoptions to speak with a service engineer.


15/16


16/16

Cisco Systems, Inc.5030 Sugarloaf Parkway, Box 465447Lawrenceville, GA 30042

678 277-1120800 722-2009

www.cisco.com

Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliatesin the U.S. and other countries. A listing of Cisco's trademarks can be found atwww.cisco.com/go/trademarks .

Third party trademarks mentioned are the property of their respective owners.The use of the word partner does not imply a partnership relationship between Cisco and anyother company. (1009R)Product and service availability are subject to change without notice.

2006-2011, 2012 Cisco and/or its affiliates. All rights reserved.April 2012 Printed in USA Part Number 4015277 Rev C

D9032 Encoder SDI Board Install

Documents

Transcript of D9032 Encoder SDI Board Install