D-Link DI-804HV Broadband Hardware VPN Router · D-Link DI-804HV Broadband Hardware VPN Router...

Broadband Hardware

Manual

Building Networks for People

VPN Router

DI-804HVD-LinkT M

02212003

2

Contents

Package Contents ................................................................................ 3

Introduction........................................................................................... 4

Getting Started ................................................................................... 10

Using the Configuration Menu............................................................. 11

Networking Basics ............................................................................. 57

Reset to Factory Default Settings ........................................................ 83

Technical Specifications ..................................................................... 84

Contacting Technical Support ............................................................. 85

Warranty and Registration ................................................................... 86

3

Contents of Package:D-Link DI-804HV Broadband Hardware VPN Router

Power Adapter – 5V DC

Ethernet (CAT5-UTP/Straight-Through) CableManual on CD

Quick Installation Guide

System Requirements For Configuration:

Computer with Windows, Macintosh, or Linux-basedoperating system with an installed Ethernet adapter

n

Internet Explorer version 6.x or Netscape Navigatorversion 6.x and above, with JavaScript enabled

n

Ethernet-Based Cable or DSL Modemn

n

Package Contents

Note: Using a power supply with a different voltage rating than the one included with theDI-804HV will cause damage and void the warranty for this product.

If any of the above items are missing, please contact your reseller.

nnn

n

4

Introduction

The D-Link DI-804HV is a 4-port Broadband Router with Virtual Private Network(VPN) functionality. It provides a complete solution for Internet surfing and officeresources sharing. It is an ideal way to extend the reach and number ofcomputers connected to your network.

After completing the steps outlined in the Quick Installation Guide (included inyour package) you will have the ability to share information and resources.

The DI-804HV is compatible with most popular operating systems, includingMacintosh, Linux and Windows, and can be integrated into a large network.

5

Connections

Features & Benefits

Receptorfor thePowerAdapter

LAN ports provideconnections to Ethernet-enabled devices.

Broadband modem and IP sharingConnects multiple computers to a broadband (cable or DSL) modem to surfthe Internet

n

Auto-sensing Ethernet SwitchEquipped with a 4-port auto-sensing Ethernet switch

n

n

n

n

n

VPN Pass-Through supportedSupports pass-through VPN sessions and allows you to setup VPN serverand VPN clients

FirewallAll unwanted packets from outside intruders are blocked to protect yournetwork

DHCP server supportedAll of the networked computers can retrieve TCP/IP settings automaticallyfrom the DI-804HV

Web-based configurationConfigurable through any networked computer’s web browser usingNetscape or Internet Explorer

Pressing theReset Buttonrestores therouter to itsoriginal factorydefault settings.

All Ethernet ports auto-sensec able ty pes to ac c omodatestr aight- through or c ross-overcable.

WAN port is theconnection for theEthernet cable to theCable or DSL modem

COM port providesserial connection fordial-up analog modem.

6

Features & Benefits continuedn Access Control supported

Allows you to assign different access rights for different users

n Packet filter supportedPacket Filter allows you to control access to a network by analyzing theincoming and outgoing packets and letting them pass or halting them basedon the IP address of the source and destination.

n Virtual Server supportedEnables you to expose WWW, FTP and other services on your LAN to beaccessible to Internet users.

n User-Definable Application Sensing TunnelUser can define the attributes to support special applications requiringmultiple connections, like Internet gaming, video conferencing, Internettelephony and so on. The DI-804HV can sense the application type andopen a multi-port tunnel for it.

n DMZ Host supportedAllows a networked computer to be fully exposed to the Internet; thisfunction is used when the special “application-sensing tunnel feature” isinsufficient to allow an application to function correctly

Introduction to BroadbandRouter TechnologyA router is a device that forwards data packets from a source to a destination. Routersforward data packets using IP addresses and not a MAC address. A router will forwarddata from the Internet to a particular computer on your LAN.

The information that makes up the Internet gets moved around using routers. Whenyou click on a link on a web page, you send a request to a server to show you the nextpage. The information that is sent and received from your computer is moved from yourcomputer to the server using routers. A router also determines the best route that yourinformation should follow to ensure that the information is delivered properly.

A router controls the amount of data that is sent through your network by eliminatinginformation that should not be there. This provides security for the computers con-nected to your router, because computers from the outside cannot access or sendinformation directly to any computer on your network. The router determines whichcomputer the information should be forwarded to and sends it. If the information is notintended for any computer on your network, the data is discarded. This keeps anyunwanted or harmful information from accessing or damaging your network.

7

Introduction to FirewallsA firewall is a device that sits between your computer and the Internet that preventsunauthorized access to or from your network. A firewall can be a computer usingfirewall software or a special piece of hardware built specifically to act as a firewall. Inmost circumstances, a firewall is used to prevent unauthorized Internet users fromaccessing private networks or corporate LAN's and Intranets.

A firewall watches all of the information moving to and from your network and analyzeseach piece of data. Each piece of data is checked against a set of criteria that theadministrator configures. If any data does not meet the criteria, that data is blockedand discarded. If the data meets the criteria, the data is passed through. This methodis called packet filtering.

A firewall can also run specific security functions based on the type of application ortype of port that is being used. For example, a firewall can be configured to work withan FTP or Telnet server. Or a firewall can be configured to work with specific UDP orTCP ports to allow certain applications or games to work properly over the Internet.

Introduction to Local Area Networking

Local Area Networking (LAN) is the term used when connecting several computerstogether over a small area such as a building or group of buildings. LAN's can beconnected over large areas. A collection of LAN's connected over a large area is calleda Wide Area Network (WAN).

A LAN consists of multiple computers connected to each other. There are many typesof media that can connect computers together. The most common media is CAT5cable (UTP or STP twisted pair wire.) On the other hand, wireless networks do not usewires; instead they communicate over radio waves. Each computer must have aNetwork Interface Card (NIC), which communicates the data between computers. A NICis usually a 10Mbps network card, or 10/100Mbps network card, or a wireless networkcard.

Most networks use hardware devices such as hubs or switches that each cable can beconnected to in order to continue the connection between computers. A hub simplytakes any data arriving through each port and forwards the data to all other ports. Aswitch is more sophisticated, in that a switch can determine the destination port for aspecific piece of data. A switch minimizes network traffic overhead and speeds up thecommunication over a network.

Networks take some time in order to plan and implement correctly. There are manyways to configure your network. You may want to take some time to determine thebest network set-up for your needs.

8

Introduction to Virtual Private NetworkingVirtual Private Networking (VPN) uses a publicly wired network (the Internet) to se-curely connect two different networks as if they were the same network. For example,an employee can access the corporate network from home using VPN, allowing theemployee to access files and printers. Here are several different implementations ofVPN that can be used.

Point-to-Point Tunneling Protocol (PPTP)PPTP uses proprietary means of connecting two private networks over the Internet.PPTP is a way of securing the information that is communicated between networks.PPTP secures information by encrypting the data inside of a packet.

IP Security (IPSec)IPSec provides a more secure network-to-network connection across the Internet or aWide Area Network (WAN). IPSec encrypts all communication between the client andserver whereas PPTP only encrypts the data packets.

Both of these VPN implementations are used because there is not a standard for VPNserver software. Because of this, each ISP or business can implement its own VPNnetwork making interoperability a challenge.

9

LEDSLED stands for Light-Emitting Diode. The DI-804HV has the following LEDsas described below:

LED LED Activity

Power A steady light indicatesa connection to a power sourcea power source

M2 LED Lights up when the device has an Internetconnection

WANA solid light indicates connection on theWAN port. This LED blinks during datatransmission

COM A solid light indicates a connection to anexternal dial-up analog modem

Flashes once per second to indicate anactive system

LOCALNETWORK(Ports 1-4)

A solid light indicates a connection to anEthernet-enabled computer on ports 1-4. ThisLED blinks during data transmission

M1 LED

10

For a typical network setup at home (as shown above), please do thefollowing:

21

34

5

Getting Started

Please refer to the followingsections of this manual foradditional information aboutsetting up a network:

Networking Basics - learnhow to check and assign yourIP Address and share files.

Using the ConfigurationMenu - learn the settings forthe DI-804HV, using the web-based interface.

With its default settings, the DI-804HV, when activated, will connectwith other D-Link Express Ethernetwork products, right out of the box.

Consult with your Cable or DSL provider for proper installation of the modem

6

You will need broadband Internet access (a Cable or DSL subscription line intoyour home or office)

Connect the Cable or DSL modem to the DI-804HV wireless broadband router(see the Quick Installation Guide included with the DI-804HV.)

If you are connecting a desktop computer to your network, you can install theD-Link DFE-530TX+ ethernet adapter into an available PCI slot. (See the QuickInstallation Guide included with the DWL-530TX+.)

If you are connecting a laptop computer to your network, install the drivers forthe Ethernet Cardbus adapter (e.g., D-Link DFE-690TXD) into a laptopcomputer.(See the Quick Installation Guide included with the DFE-690TXD.)

The Modem can be used as a dialup backup for xDSL/Cable connection

11

Using the Configuration MenuWhenever you want to configure your network or the DI-804HV, you can access theConfiguration Menu by opening the web-browser and typing in the IP Address of theDI-804HV. The DI-804HV default IP Address is shown below:

n Open the web browser n Type in the IP Address of

the DI-804HV (http://192.168.0.1)

Home > Wizard

The Home>Wizard screen willappear. Please refer to theQuick Installation Guide formore information regarding theSetup Wizard.

http://192.168.0.1

Note: If you have changed the default IP Address assigned to the DI-804HV, make sure toenter the correct IP Address.

The factory default User name is admin and the defaultPassword is blank (empty). It is recommended that youchange the admin password for security purposes. Pleaserefer to Tools>Admin to change the admin password.

Clicking Apply will save changes made to the page

Apply

Clicking Cancel will clear changes made to the page

Clicking Help will bring up helpful information regarding the page

Help

Clicking Restart will restart the router. (Necessary for some changes.)

Cancel

Restart

12

Using the Configuration MenuSetup Wizard

The welcome screen outlines thesteps to complete the setupwizard. Click Next to continue.

Once you have logged in, theHome screen will appear.

Click Run Wizard

Click Next

13

Using the Configuration MenuSetup Wizard > Set Password

Old Password- This information is masked.

New Password- Type in the new password for the admin account.

Reconfirm- Type in the new password again to confirm. Click Next to con-tinue with the Setup Wizard.

Click Next

14

Select Others only if you use PPTP in Europe or Big PondCable in Australia.

Using the Configuration MenuSetup Wizard > Time Zone

Select the appropriate time zone for your location-Select the proper time zone.Selections can be made byclicking on the drop down list.Click Next to continue.

Click Next

If you are unsure of which setting to select, please con-tact your Internet Service Provider.

Setup Wizard > Connection Type (WAN)

Select Your Internet Connection-

You will be prompted to se-lect the type of internet con-nection for your router.Choose the appropriate se-lection and click Next to con-tinue.

Click Next

15

Using the Configuration MenuSetup Wizard > Set Dynamic IP Address

Host Name- Host name is the section where you input the name of yourISP. This section is optional and is not required to be filled in.

MAC Address- Each network adapter has a discrete Media Access Control(MAC) address. Note that some computer and peripherals mayalready include built-in network adapter.

Clone MACAddress-

By clicking on Clone MAC Address, the DI-804HV will auto-matically copy the MAC address of the network adapter in yourcomputer. You can also manually type in the MAC address.Click Next to continue.

If your ISP uses Dynamic IP Address, this screen will appear: (Used mainly for CableInternet service.

Click Next

16

Using the Configuration MenuSetup Wizard > Set Static IP Address

WAN IP Address- If your ISP requires a Static IP Address, and this option isselected, then this screen appear. Enter the IP address infor-mation originally provided to you by your ISP. You will need tocomplete all the required fields.

WAN Subnet Mask- The subnet for the DI-804HV is preconfigured to 255.255.255.0.Configurations can be made in, but not recommended. Thisfeature is for advanced users.

WAN Gateway- This information is provided by your ISP.

Primary DNS- The Primary DNS can be found by contacting the ISP.

Secondary DNS- The Seconday DNS can be found by contacting the ISP.

If your ISP uses a Static IP Address, and this option is selected, then this screen willappear.

Click Next

17

Using the Configuration MenuSetup Wizard > PPPoE

PPPoE Account- Enter in the username provided to you by your ISP.

If your ISP uses PPPoE (Point-to-Point Protocol over Ethernet), and this option isselected, then this screen will appear: (Used mainly for DSL Internet service.)

PPPoE Password- Enter in the password provided to you by your ISP.

PPPoE ServiceName-

Enter in the name of your service provider. This is an optionalfield and is not necessary to be filled in.

Click Next

18


Configure this section only if you have an analog dial-up account. Otherwise click Nextto skip.

Dial-upTelephone-

Enter the telephone number to connect to your ISP.

Dial-up Account- This information is provided by your ISP. The Dial-up Account isalso known as username.

Dial-up Password- Enter in the password to log into your Dial-up account.

Primary DNS- The Primary DNS can be found by contacting the ISP.

Secondary DNS- The Seconday DNS can be found by contacting the ISP.

Click Next

19


Back- Click on Back button to go back to previous page.

Restart- Click on Restart button to finalize the settings made.

Exit- Click on Exit button to end the Setup Wizard without savingany changes.

Click Restart

20

Using the Configuration MenuHome > WAN

Choose WAN TypeWAN stands for Wide Area Network. In this case WAN represents the mode in whichyou connect to the Internet. If you are uncertain, please ask your ISP which of thefollowing represents your connection mode to the Internet:

Static IP Address- Your ISP assigns you a Static IP Address

DynamicIP Address-

Obtain an IP address from your ISP automatically (mainly forCable users)

PPP overEthernet- Some ISPs require the use of PPPoE to connect to their

services (mainly for DSL users)

For use in Europe only

Others-

For use in Australia only

PPTP-

Big Pond Cable-

21

Using the Configuration MenuHome > WAN > Dynamic IP Address

Most Cable modem users will select this option to obtain an IP Address automaticallyfrom their ISP (Internet Service Provider).

Host Name- This is optional, but may be required by some ISPs. The hostname is the device name of the Router.

MAC Address- The default MAC Address is set to the WAN’s physical inter-face MAC address on the Router.

CloneMAC Address-

This feature will copy the MAC address of the Ethernet card,and replace the WAN MAC address of the Router with thisEthernet card MAC address. It is not recommended that youchange the default MAC address unless required by your ISP.

Renew IP Forever- Enable this feature to allow the router to automatically recon-nect to the ISP if the connection drops.

22

Using the Configuration MenuHome > WAN > Static IP Address

If you use a Static IP Address, you will input information here that your ISP has providedto you.

Secondary DNS- (Optional) Input the Secondary DNS address provided by yourISP.

Primary DNS- Input the primary DNS address provided by your ISP

WAN Gateway- Input the Gateway address provided by your ISP

WAN Subnet Mask- Input the Subnet Mask provided by your ISP

WAN IP Address- Input the IP Address provided by your ISP

23

Using the Configuration MenuHome > WAN > PPPoE

Most DSL users will select this option to obtain an IP address automatically from theirISP through the use of PPPoE.

MTU- Maximum Transmission Unit; default is 1492; you may need tochange the MTU to conform to your ISP.

AssignedIP Address-

(Optional) Enter in the IP Address if you are assigned a staticPPPoE address.

PPPoEService Name-

(Optional) Check with your ISP for more information if theyrequire the use of service name.

MaximumIdle Time-

Enter a maximum idle time during which Internet connection ismaintained during inactivity. To disable this feature, enable Auto-reconnect.

(Optional) Input the secondary DNS address

Primary DNS- You will get the DNS IP automatically from your ISP but youmay enter a specific DNS address that you want to use instead.

PPPoE Password-

Your PPPoE username provided by your ISPPPPoE Account-

Your PPPoE password is provided by your ISP

24

Using the Configuration MenuHome > WAN > Dial-up Network

Most Dial-up users will select this option to connect to their ISP through an analog dial-up modem. This feature can be used as a back-up when your broadband connectivity isunavailable.

Extra Settings-

AssignedIP Address-

(Optional) Enter in the IP Address if you are assigned a staticPPPoE address.

Primary DNS-Seconday DNS-

If the settings are configured as “0.0.0.0,” they will be auto-matically assigned upon connection.

Baud Rate-

Maximum Idle Time- Enter a maximum idle time during which Internet connectionis maintained during inactivity. To disable this feature, en-able Auto-reconnect.

Dial-up Password- Password provided by your ISP

Dial-up Account-

Telephone number to connect to your ISPDial-up Telephone -

Username provided by your ISP

The communication speed between the DI-804HV and yourmodem.

This setting is used to optimize the communication quality be-tween the ISP and your analog dial-up modem. (Initializationstring) - optional.

25

Using the Configuration MenuHome > WAN > PPTP

PPTP Password- Enter the PPTP password

PPTP Account- Enter the PPTP account name

My Subnet Mask- Enter the Subnet Mask

Connection ID- (Optional) Enter the connection ID if required by your ISP

MaximumIdle Time-

Enter a maximum idle time during which Internet connection ismaintained during inactivity. To disable this feature, enable Auto-reconnect.

My IP Address- Enter the IP Address

Server IP Address- Enter the Server IP Address

Point-to-Point Tunneling Protocol (PPTP) is a WAN connection used in Europe.

26

Using the Configuration Menu

Home > WAN > BigPond Cable

Account- Enter in the username for the BigPond account

Password- Enter the password for the BigPond account

Login Server- (Optional) enter the Login Server name if required

Renew IP forever- If enabled, the device will automatically connect toyour ISP after your unit is restarted or when theconnection is dropped.

Dynamic IP Address for BigPond is a WAN connection used in Australia.

27

Home > LAN


Domain Name- (Optional) The name of your local domain

Subnet Mask- The subnet mask of the LAN interface.The default subnet mask is 255.255.255.0

LAN IP Address- The IP address of the LAN interface.The default IP address is: 192.168.0.1

LAN is short for LocalArea Network. This isconsidered your inter-nal network. Theseare the IP settings ofthe LAN interface forthe DI-804HV. Thesesettings may be re-ferred to as Privateset tings. You maychange the LAN IPaddress if needed.The LAN IP address isprivate to your internalnetwork and cannotbe se e n o n t heInternet.

28

Home >DHCP


DHCP stands for Dynamic Host Control Protocol. The DI-804HV has a built-in DHCPserver. The DHCP Server will automatically assign an IP address to the computers onthe LAN/private network. Be sure to set your computers to be DHCP clients by settingtheir TCP/IP settings to “Obtain an IP Address Automatically.” When you turn yourcomputers on, they will automatically load the proper TCP/IP settings provided by theDI-804HV. The DHCP Server will automatically allocate an unused IP address from theIP address pool to the requesting computer. You must specify the starting and endingaddress of the IP address pool.

IP Pool StartingAddress-

The starting IP address for the DHCP server’s IP assignment.

IP Pool EndingAddress-

The ending IP address for the DHCP server’s IP assignment.

Lease Time- The length of time for the DHCP lease.

DHCP Clients List- Lists the DHCP clients connected to the DI-804HV. ClickRefresh to update the list. The table will show the Host Name,IP Address, and MAC Address of the DHCP client computer.

Enable or disable the DHCP service.DHCP Server-

29

Home >VPN Settings


VPN Settings are settings that are used to create virtual private tunnels to remote VPNgateways. The tunnel technology supports data confidentiality, data origin, authenticationand data integrity of network information by utilizing encapsulation protocols, encryptionalgorithms, and hashing algorithms.

Max. nu mber oftunnels-

Create a name for the tunnel.

NetBIOS broadcast-

Check here to enable VPN tunnels. When you are notusing the VPN feature, it is best to keep VPN disabled.

VPN -

Method- IPSec VPN supports two kinds of key-obtained methods:manual key and automatic key exchange. Manual keyapproach indicates that the two endpoint VPN gatewaysrequire setting up authentication and encryption key bythe Administrator manually. However, IKE approach willperform automatic Internet key exchange. Admins of bothendpoint gateways will only need to set the samepre-shared key.

For more indepth configuration to adjust manualkey or IKE method settings, click More.

More-

Tunnel Name-

Select the maximum number of allowable tunnels.

Enable this to allow NetBIOS braodcast over the VPNtunnels.

30

Home >VPN Settings > Tunnel (IKE)


There are three parts that are necessary to setup theconfiguration of IKE for the dedicated tunnel: basic setup, IKEproposal setup, and IPSec proposal setup. Basic setupincludes the setting of following items: local subnet, localnetmask, remote subnet, remote netmask, remote gateway,and pre-shared key. The tunnel name is derived from previouspage of VPN setting. IKE proposal setup includes the settingof a set of frequent-used IKE proposals and selecting from theset of IKE proposals.

VPN Settings - IKE-

Local Subnet- The subnet of the VPN gateway’s local network. It can be ahost, a partial subnet or a whole subnet.

Local Netmask- The netmask of the VPN gateway’s local network.

Aggressive Mode- Enabling this mode will accelerate establishing the tunnel,but the device will have less security.

Tunnel Name- Current tunnel name.

31


Remote Subnet- The subnet of the remote VPN gateway’s local network. Itcan be a host, a partial subnet or a whole subnet.

Home >VPN Settings > Tunnel Continued...

Remote Netmask- The subnet of the remote VPN gateway’s local network. Itcan be a host, a partial subnet or a whole subnet. a wholesubnet.

Remote Gateway- The WAN IP address of remote VPN gateway.

Preshared Key- The first key that supports IKE mechanism of both VPNgateways for negotiating further security keys. The pre-shared key must be the same for both endpoint gateways.

IKE Proposal index- Click the button to setup a set of frequent-used IKEproposals and select from the set of IKE proposals for thededicated tunnel.

IPSec Proposalindex-

Click the button to setup a set of frequent-used IPSecproposals and select from the set of IKE proposals for thededicated tunnel.

32

Remote Subnet- The subnet of the remote VPN gateway’s local network. Itcan be a host, a partial subnet or a whole subnet.

Remote Netmask- The subnet of the remote VPN gateway’s local network.It can be a host, a partial subnet or a whole subnet.

Remote Gateway- The WAN IP address of remote VPN gateway.

Local SPI- The value of local SPI should be set in hex format.

Home >VPN Settings > Tunnel (Manual)


Local Subnet- The subnet of the VPN gateway’s local network. It can be ahost, a partial subnet or a whole subnet.

Local Netmask- Local netmask combined with local subnet to form a subnetdomain.

Aggressive Mode- Enabling this mode will accelerate establishing tunnel, butthe device will have less security.

Tunnel Name- Current tunnel name.

33

Home >VPN Settings > Tunnel (Manual)


Remote SPI- The value of remote SPI should be set in hex format.

Encapsulationprotocol-

There are two protocols that can be selected: ESP and AH.

EncryptionAlgorithm-

There are two algorithms that can be selected: 3DES andDES.

Encryption Key- For DES, the encryption key is 8 bytes. (16 Char.)For 3DES, the encryption key is 24 bytes (48 Char.)

AuthenticationAlgorithm-

Authentication Key- For MD5, the authentication algorithm is16 bytes. (32 Char.)For SHA1, the authentication algorithm is 20 bytes.(40 Char.)

Life Time- Enter in the life time value.

Life Time Unit- There are two units that can be selected: second and KB.

SHA1 or MD5 algorithm can be selected.

34

Using the Configuration MenuHome >VPN Settings > Tunnel > Set IKE Proposal

IKE Proposal index- A list of selected proposal indexes from the IKE proposal poollisted below.

Proposal Name-

DH Group- There are three groups can be selected: group 1 (MODP768),group 2 (MODP1024), group 5 (MODP1536).

Encrypt algorithm- There are two algorithms that can be selected: 3DES andDES.

Auth algorith- There are two algorithms that can be selected: SHA1 andMD5.

It indicates which IKE proposal to be focused. First char ofthe name with 0x00 value stands for the IKE proposal is notavailable.

35

Using the Configuration MenuHome >VPN Settings> Tunnel > Set IKE Proposal Continued...

Life Time- Enter in the life time value.


Proposal ID- The identifier of IKE proposal can be chosen for addingcorresponding proposal to the dedicated tunnel.

Add to- Click it to add the chosen proposal indicated by proposal IDto IKE Proposal index list.

36

Using the Configuration MenuHome >VPN Settings > Tunnel > Set IPSEC Proposal

IPSec Proposalindex-

A list of selected proposal indexes from the IPSec proposalpool listed below.

Proposal Name-

DH Group- There are three groups that can be selected: group 1(MODP768), group 2 (MODP1024), group 5 (MODP1536).

Encap protocol- There are two protocols that can be selected: ESP and AH.

Encrypt algorith- There are two algorithms that can be selected: 3DES andDES.

It indicates which IPSec proposal to be focused. First char ofthe name with 0x00 value stands for the proposal is notavailable.

Auth algorith- There are two algorithms that can be selected: SHA1 andMD5.

37

Using the Configuration MenuHome >VPN Settings> Tunnel > Set IPSEC Proposal Continued...

Life Time- Enter in a life time value.


Proposal ID- The identifier of IPSec proposal can be chosen for adding theproposal to the dedicated tunnel.

Add to- Click it to add the chosen proposal indicated by proposal IDto IPSec Proposal index list.

38

Advanced > Virtual ServerUsing the Configuration Menu

The DI-804HV can be configured as a virtual server so that remote users accessing Webor FTP services via the public IP address can be automatically redirected to local serversin the LAN (Local Area Network).The DI-804HV firewall feature filters out unrecognized packets to protect your LAN networkso all computers networked with the DI-804HV are invisible to the outside world. If youwish, you can make some of the LAN computers accessible from the Internet by enablingVirtual Server. Depending on the requested service, the DI-804HV redirects the externalservice request to the appropriate server within the LAN network.

Service Ports- Enter in the service port or ports to be used. A range of portscan be specified with a hyphen. (e.g., 20-21)

Service IP- The IP address of the internal computer that will be using thevirtual service

Enable- Select to activate the policy

ID- The ID number is automatically assigned

Well knownservices-

Use the pull-down menu to select from a list of well-knownvirtual services

Schedule- Select Always, or choose From and enter the time period dur-ing which the virtual service will be available

39

Using the Configuration MenuAdvanced > Application

Some applications require multiple connections, such as Internet gaming, videoconferencing, Internet telephony and others. These applications have difficulties workingthrough NAT (Network Address Translation). Special Applications makes some of theseapplications work with the DI-804HV. If you need to run applications that require multipleconnections, specify the port normally associated with an application in the Triggerfield, then enter the public ports associated with the trigger port into the Incoming Portsfield.

At the bottom of the screen, there are already defined special applications. To usethem, select one from the drop down list and select an ID number you want to use.Then click the “Copy to” button and the router will fill in the appropriate information tothe list. You will then need to enable the service. If the mechanism of Special Applica-tions fails to make an application work, try using DMZ host instead.

Note! Only one PC can use each Special Application tunnel.

Trigger- This is the port used to trigger the application. It can be eithera single port or a range of ports.

Incoming Ports- This is the port number on the WAN side that will be used toaccess the application. You may define a single port or a rangeof ports. You can use a comma to add multiple ports or portranges.

Enable- Select to activate the policy

40

Using the Configuration MenuAdvanced > MAC Filters

MAC (Media Access Control) Filters are used to deny or allow LAN (Local Area Network)computers from accessing the Internet and network by their MAC address.

At the bottom of the screen, there is a list of MAC addresses from the DHCP clientcomputers connected to the DI-804HV. To use them, select one from the drop down listand select an IP number you want to use. Then click the “Copy to” button and the DI-804HV will fill in the appropriate information to the list.

Disabled MAC Filter- Select this option if you do not want to use MAC filters.

Only allow computers with MAC address listed below to access the network-Select this option to only allow computers that are in the list

to access the network and Internet. All other computers willbe denied access to the network and Internet.

Only deny computers with MAC address listed below to access the network-Select this option to only deny computers that are in the list

to access the network and Internet. All other computers willbe allowed access to the network and Internet.

Enter the MAC Address of the client that will be filteredMAC Address-

Select this option for the specific IP filter policy to take effect.Enable-

41

Using the Configuration MenuAdvanced > IP Filter

Disabled IP Filter-Select this option if you do not want to use IP filters.

Allow all computers to access the Internet except those listed below-Those in the list will be denied access to the Internet; all other computers will be allowedaccess to the Internet.

Schedule-

IP-Enter in the IP address range of the computers that you want the policy to apply to. If itis only a single computer that you want the policy applied to, then enter the IP address ofthat computer in the Start Source IP and leave the End Source IP blank.

Use IP (Internet Protocol)filters to allow or denycomputers access to theInternet based on their IPaddress.

Deny all computers access to the Internet except those listed below-Select this option to deny all computers access to the Internet except those that arelisted below. All other computers will be denied access to the Internet.

Port-Enter in the port range of the TCP/UDP ports that you want the policy to apply to. If it isonly a single port that you want the policy applied to, then enter the port number in theStart Port field and leave the End Port field blank. If you want to use all the ports, you canleave the port range empty.

Enabled or Disabled-Click Enabled to apply the filter policy or click Disabled to enter an inactive filter policy(You can reactivate the policy later.)

Select Always, or choose From and enter the time period during which the IP filter policywill be in effect.

42

Using the Configuration MenuAdvanced > Domain Filter

Use Domain filters to allow or deny computers access to specific Internet domainswhether it is through www, ftp, snmp, etc.

Disabled Domain Filter- Select this option if you do not want to use Domain filters.

Allow users to access the following domains and block all other domains-Select this option to allow users to access the specified

Internet domains listed below. Users will be denied accessto all other Internet domains.

Deny users to access the following domains and permit all other domains-Select this option to deny users to access the specified

Internet domains listed below. Users will be allowed accessto all other Internet domains.

Domain suffix- Enter in the domain suffix of the Internet domain you want touse. (example: shopping.com, sports.net)

Log- Select this option to log usage to the specified domain. Thelogs can be viewed in Status > Log.

43

Using the Configuration MenuAdvanced > SNMP

SNMP (Simple Network Management Protocol) is a widely used network monitoring andcontrol protocol that reports activity on each network device to the administrator of thenetwork. SNMP can be used to monitor traffic and statistics of the DI-804HV. The DI-804HV supports SNMP v1.

Enable SNMP-

Get Community-

(Simple Network Management Protocol)

Enter the password public in this field to allow “Read only”access to network administration using SNMP. You can viewthe network, but no configuration is possible wth this setting.

Set Community- Enter the password private in this field to gain “Read and Write”access to the network using SNMP software. The administra-tor can configure the network with this setting.

Local-

Remote- WAN (Wide Area Network)

LAN (Local Area Network)

44

Using the Configuration MenuAdvanced > DDNS

DDNS (Dynamic Domain Name System) keeps dynamic IP addresses (e.g., IPaddresses assigned by a DHCP capable router or server) linked to a domain name.Users who have a Dynamic DNS account may use this feature on the DI-804HV.

DDNS- When an IP address is automatically assigned by a DHCP server,DDNS automatically updates the DNS server. Select Disabledor Enabled

Provider- Select from the pull-down menu

Host Name- Enter the Host name

Username/Email- Enter the username or email address

Password/Key- Enter the password or key

45

Using the Configuration MenuAdvanced > Routing

Dynamic Routing Settings allow the VPN Router to route IPpackets to another network automatically. The RIP protocolis applied, and broadcasts the routing information to otherrouters on the network regularly.By default, it is set to disable. Check to enable (RIPv1 / RIPv2)protocol.

Dynamic Routing

Static Routing

Static routing settings allow the VPN Router to route IP packetsto another network. The routing table sorts the routinginformation so that your network device knows where toredirect the IP packets to the proper network.By default, it is set to disable. To change this configuration,select enable.

Routing Tables allow you to determine which physical interface address touse for outgoing IP data grams. If you have more than one routers andsubnets, you will need to enable routing table to allow packets to find properrouting path and allow different subnets to communicate with each other.

46

Using the Configuration MenuAdvanced > DMZ

If you have a computer that cannot run Internet applications properly from behind the DI-804HV, then you can allow that computer to have unrestricted Internet access. Enter theIP address of that computer as a DMZ (Demilitarized Zone) host with unrestricted Internetaccess. Adding a client to the DMZ may expose that computer to a variety of securityrisks; so only use this option as a last resort.

47

Using the Configuration MenuTools> Admin

Password-

RemoteManagement-

To change the admin password, enter in the old password, andenter the new password twice to confirm

You can change the admin password here. It is recommended that you change theadmin password from the default setting. The default password is blank (no password).

Remote Management allows the device to be configuredthrough the WAN (Wide Area Network) port from the Internetusing a web browser. A username and password is stillrequired to access the browser-based management interface.

IP Address-Internet IP Address of the computer that has access to theDI-804HV. If the IP Address is set to 0.0.0.0, this allows allInternet IP addresses to access the DI-804HV.

Port-The port number used to access the DI-804HV.E.g., http://x.x.x.x:8080, where x.x.x.x. is the WAN IP addressof the DI-804HV and 8080 is the port used for the Web Manage-ment interface.

48

Using the Configuration MenuTools> Time

Enable NTP-

Sync-

Select to enable NTP and synchronize the time settings on yournetwork using an NTP server

Set the time here by entering it manually or use NTP (Network Time Protocol.) NTP isstandard protocol on the Internet that sychronizes the time settings accurately for all thecomputers on your network.

Click Sync to activate the synchronization with the NTPserver that you input in the default NTP server field

Default NTPserver-

If you are enabling NTP, please enter the link to the default server.

Time Zone- Select your time zone from the pull-down menu

Set Device Dateand Time-

If you are entering the time manually, select the correct Year;Month; Day; Hour; Minute and Second

49

Using the Configuration MenuTools > System

Click Backup Setting to save the current settings to the localHard Drive

Click Browse to find the settings file, then click Load

Save Settings toLocal Hard Drive-

Load Settings fromLocal Hard Drive-

Restore to FactoryDefault Settings-

Click Restore to Default to restore the factory default settings

The current system settings can be saved as a file onto the local hard drive. Thesaved file or any other saved setting file created by the DI-804HV can be uploaded intothe unit. To reload a system settings file, click on Browse to search the local harddrive for the file to be used. The device can also be reset back to factory defaultsettings by clicking on the Reset to Default button. Use the restore feature only ifnecessary. This will erase previously saved settings for the unit. Make sure to saveyour system settings to the hard drive before doing a factory restore.

50

Using the Configuration MenuTools > Firmware

Browse- After you have downloaded the new firmware, click Browse inthis window to locate the firmware update on your hard drive.Click Apply to complete the firmware upgrade.

Note! Do not power off the unit when it is being upgraded. When theupgrade is complete, the unit will be restarted automatically.

You can upgrade the firmware by using this tool. First, check the D-Link support site forfirmware updates at http://support.dlink.com. Make sure that the firmware you want touse is saved on the local hard drive of your computer. Click on Browse to search thelocal hard drive for the firmware that you downloaded from the D-Link website to be usedfor the update. Upgrading the firmware will not change any of your system settings but itis recommended that you save your system settings before doing a firmware upgrade.

51

Using the Configuration MenuTools > Misc

Block WAN Ping- Click Enable to block the WAN ping. Computers on the Internetwill not get a reply back from the DI-804HV when it is being“ping”ed. This may help to increase security.

Restart Device- Click Reboot to restart the unit.

Non-standardFTP port-

If an FTP server you want to access is not using the standard port21, then enter in the port number that the FTP server is usinginstead.

Ping Test- In the open box, enter an URL (i.e. www.dlink.com) or an IP ad-dress and click on Ping to test your internet connection.

52

Using the Configuration MenuStatus > Device Info

This screen displays information about the DI-804HV

Refresh- Click Refresh to update the page.

1.20,Thu,Jan 30 2003

53

Using the Configuration MenuStatus > Log

This screen displays activities occurring on the DI-804HV

Log Settings- Click for advanced features (see next page.)

Back- Click Back to return to the top of the log.

Refresh- Click Refresh to update the log.

(1.20)

54

Using the Configuration MenuStatus > Log Settings

Send E-Mail alert to- Enter in the email address of the recipient who will receivethe email log.

Enter in the IP address of a syslog server within the network.Click Enable to activate the policy. The DI-804HV will send allof it’s logs to the specified syslog server.

IP Address of theSyslog Server-

E-Mail Alert- The DI-804HV can be set up to send the log files to a specificemail address.

SMTP Server IP- Enter in the IP address of the mail server.

Send Mail Now- Click to send mail immediately.

(1.20)

55

Using the Configuration MenuStatus > Stats

In Stats section, traffic statistics are displayed.

Refresh- This will update the page.

Reset- This will reset the packet counter to zero.

WAN- Displays Received / Transmitted packets from the WAN port.

LAN- Displays Received / Transmitted packets from the LAN port.

56

Using the Configuration MenuHelp

This screen displays the complete Help menu. For help at anytime, click the Help tabin the Configuration menu.

57

Using the Network Setup Wizard in Windows XP

In this section you will learn how to establish a network at home or work,using Microsoft Windows XP.

Note: Please refer to websites such as http://www.homenethelp.comand http://www.microsoft.com/windows2000 for information about networking

computers using Windows 2000, ME or 98.

Go to Start>Control Panel>Network ConnectionsSelect Set up a home or small office network

Networking Basics

When this screen appears, Click Next.

58

Please follow all the instructions in this window:

Networking Basics

Click Next

In the following window, select the best description of your computer. If yourcomputer connects to the internet through a gateway/router, select thesecond option as shown.

Click Next

59

Enter a Computer description and a Computer name (optional.)

Networking Basics

Click Next

Enter a Workgroup name. All computers on your network should have thesame Workgroup name.

Click Next

60

Please wait while the Network Setup Wizard applies the changes.

Networking Basics

When the changes are complete, click Next.

Please wait while the Network Setup Wizard configures the computer.This may take a few minutes.

61

Networking Basics

In the window below, select the option that fits your needs. In this example, Create aNetwork Setup Disk has been selected. You will run this disk on each of thecomputers on your network. Click Next.

Insert a disk into the Floppy Disk Drive, in this case drive A.

Format the disk if you wish, and click Next.

62

Networking Basics

Please read the information under Here’s how in the screen below. After you completethe Network Setup Wizard you will use the Network Setup Disk to run the NetworkSetup Wizard once on each of the computers on your network. To continue click Next.

63

Networking BasicsPlease read the information on this screen, then click Finish to complete theNetwork Setup Wizard.

The new settings will take effect when you restart the computer. Click Yes torestart the computer.

You have completed configuring this computer. Next, you will need to run theNetwork Setup Disk on all the other computers on your network. After run-ning the Network Setup Disk on all your computers, your new wireless net-work will be ready to use.

64

n

Networking BasicsNaming your Computer

To name your computer, please follow these directions:In Windows XP:

Click Start (in the lower left corner of the screen)

Right-click on My Computer

Select Properties and click

n

n

n

n

n

Select the ComputerName Tab in the SystemProperties window.

You may enter a Com-puter Description if youwish; this field is optional.

To rename the computerand join a domain, ClickChange.

65

Networking BasicsNaming your Computer

n In this window, enter theComputer name

Select Workgroup and enter thename of the Workgroup

All computers on your networkmust have the same Workgroupname.

Click OK

n

n

n

Checking the IP Address in Windows XP

The wireless adapter-equipped computers in your network must be in the same IP Ad-dress range (see Getting Started in this manual for a definition of IP Address Range.) Tocheck on the IP Address of the adapter, please do the following:

Right-click on theLocal AreaConnection iconin the task bar

Click on Status

n

n

OK

Networking BasicsChecking the IP Address in Windows XP

This window will appear.

Click theSupport tab

Click Close

n

n

Assigning a Static IP Address in Windows XP/2000

Note: Residential Gateways/Broadband Routers will automatically assign IP Ad-dresses to the computers on the network, using DHCP (Dynamic Host ConfigurationProtocol) technology. If you are using a DHCP-capable Gateway/Router you willnot need to assign Static IP Addresses.

If you are not using a DHCP capable Gateway/Router, or you need to assign a Static IPAddress, please follow these instructions:

n

n

Go to Start

Double-click onControl Panel

66

67

Networking BasicsAssigning a Static IP Address in Windows XP/2000

n Double-click onNetworkConnections

n

n Double-click onProperties

Right-click on Local AreaConnections

68

Networking BasicsAssigning a Static IP Addressin Windows XP/2000

n

The DNS server information will be supplied by your ISP (Internet Service Provider.)

n Click OK

n

n

n

Enter the LAN IP address ofthe Wireless Router. (D-Linkwireless routers have a LAN IPaddress of 192.168.0.1)

Enter the LAN IP address ofthe Wireless Router. (D-Linkwireless routers have a LAN IPaddress of 192.168.0.1)

192 168 0 1

192 168 0 1

69

Networking BasicsAssigning a Static IP Address with Macintosh OSX

n

n

n

n

n

n

Go to the Apple Menu and se-lect System Preferences

cClick on Network

Select Built-in Ethernet in theShow pull-down menu

Select Manually in the Con-figure pull-down menu

Input the Static IP Address,the Subnet Mask and theRouter IP Address in the ap-propriate fields

Click Apply Now

70

Networking BasicsSelecting a Dynamic IP Address with Macintosh OSX

Go to the Apple Menu and selectSystem Preferences

Click on Network

Select Built-in Ethernet in theShow pull-down menu

Select Using DHCP in theConfigure pull-down menu

Click Apply Now

The IP Address, Subnetmask, and the Router’s IPAddress will appear in a fewseconds

n

n

n

n

n

n

71

Networking BasicsAdding and Sharing Printers in Windows XP

After you have run the Network Setup Wizard on all the computers in your network(please see the Network Setup Wizard section at the beginning of Networking Basics,)you can use the Add Printer Wizard to add or share a printer on your network.

Whether you want to add a local printer (a printer connected directly to one computer,)share an LPR printer (a printer connected to a print server) or share a network printer(a printer connected to your network through a Gateway/Router,) use the Add PrinterWizard. Please follow the directions below:

First, make sure that you have run the Network Setup Wizard on all of the computerson your network.

On the following pages, we will show you these 3 ways to use the Add Printer Wizard:

1. Adding a local printer

2. Sharing an network printer

3. Sharing an LPR printer

For help with other tasks, that we have not covered here, in home or small office networking,see Using the Shared Documents folder and Sharing files and folders in the Helpand Support Center in Microsoft Windows XP.

(Other Networking Tasks)

72

Networking BasicsAdding a local printer (a printer connected directly to a computer)

A printer that is not shared on the network and is connected directly to one computeris called a local printer. If you do not need to share your printer on a network, followthese directions to add the printer to one computer.

Go toStart>Printersand Faxes

Click on Add a printer

n

n

73

Networking BasicsAdding a local printer

Click Next

Select Local printerattached to thiscomputer

(Deselect Automati-cally detect and installmy Plug and Playprinter if it has beenselected.)

Click Next

Select Use the follow-ing port:

From the pull-down menuselect the correct portfor your printer

(Most computers use the LPT1: port,as shown in the illustration.)

Click Next

n

n

n

n

n

n

n

74


Select and highlightthe correct driver foryour printer.

Click Next

(If the correct driver isnot displayed, insert theCD or floppy disk thatcame with your printerand click Have Disk.)

At this screen, you canchange the name of theprinter (optional.)

Click Next

Select Yes, to print atest page. A successfulprinting will confirm thatyou have chosen thecorrect driver.

Click Next

n

n

n

n

n

n

75


This screen gives you information about your printer.

Click Finish

When the test page has printed,

Click OK

76


Go to Start> Printersand Faxes

A successful installation will displaythe printer icon as shown at right.

You have successfully added a localprinter.

Sharing a network printerAfter you have run the Network Setup Wizard on all the computers on your network,you can run the Add Printer Wizard on all the computers on your network. Pleasefollow these directions to use the Add Printer Wizard to share a printer on yournetwork:

Go to Start>Printers and Faxes

n

n

77

Networking BasicsSharing a network printer

Click onAdd a printer

Click Next

SelectNetwork Printer

Click Next

n

n

n

n

78


Select Browse fora printer

Click Next

Select the printer youwould like to share

Click Next

Click Finishn

n

n

n

79


To check for properinstallation:

Go to Start > Printersand Faxes

The printer icon will appear at right,indicating proper installation.

You have completed adding theprinter.

To share this printeron your network:

Remember the printername

Run the Add PrinterWizard on all thecomputers on yournetwork

Make sure you havealready run theNetwork SetupWizard on all thenetwork computers

After you run the Add PrinterWizard on all the computers in thenetwork, you can share the printer.

n

n

n

n

n

80

Networking BasicsSharing an LPR printer

To share an LPR printer (using a print server,) you will need a Print Server such asthe DP-101P+. Please make sure that you have run the Network Setup Wizard onall the computers on your network. To share an LPR printer, please follow thesedirections:

Go to Start >Printers andFaxes

Click on Adda Printer

The screen to theright will appear

Click Next

SelectLocalPrinter...

Click Next

n

n

n

n

n

81


Click Next

Select Keep existingdriver

If the printer driver is already installed, dothe following:

Click Have Disk

Insert the printer driver disk thatcame with your printer.

Select the printer youare adding from the listof Printers.

Click Finish

This screen will show youinformation about yourprinter.

n

n

n

n

n

n

n

82


Note: You must run the Network Setup Wizard on all the computers on your network beforeyou run the Add Printer Wizard.

Please run the Add PrinterWizard on all the computerson your network in order toshare the printer.

Click Finish to complete theaddition of the printer.

This screen will display informationabout your printer.

Click Next

Select Yes, to print a test page.

Click Next

Please remember the name ofyour printer. You will need thisinformation when you use theAdd Printer Wizard on theother computers on yournetwork.

You can rename your printer ifyou choose. It is optional.

n

n

n

n

n

n

n

83

After you have tried other methods for troubleshooting your network, youmay choose to Reset the DI-804HV to the factory default settings.

To hard-reset the D-Link DI-804HV to the Factory Default Settings, please dothe following:

Resetting the DI-804HV to the Factory Default Settings

n

n Use a paper clip to press the Reset button andpower on.

Locate the Reset button on the back of the DI-804HV

n Turn off the DI-804HV

n After you have completed the above steps, the DI-804HVwill be reset to the factory default settings

n Hold for about 5 seconds (don’t hold too long) andthen release. (Or, release when M1 and M2 flashat the same time.)

84

Technical Specifications

VPN Pass Through FunctionPPTPL2TPIPSec

Device Management

nnn

StandardsIEEE 802.3 10BASET-T Ethernetn

nn IEEE 802.3x Flow Control

IEEE 802.3u 100BASE-TX Fast Ethernet

ANSI/IEEE 802.3 NWay auto-negotiationn

Web-Based – Internet Explorer 6x or later; Netscape Navigator 6x orlater; or other Java- enabled browsers.

n

LEDsWANLANM1M2

nnnn

Operating Temperature

41°F to 131°F ( 5°C to 55°C)nHumidity

10-90%nPower

DC 5Vn

L = 7.56 inches (192mm)W = 4.65 inches (48mm)H = 1.22 inches (31mm)

nnn

Dimensions

~10.8 oz. (0.3 kg)Weight

n

4 x NWay 10BASE-T/100BASE-TX Fast Ethernet LAN (Media Auto Sensing)1 x NWay 10BASE-T/100BASE-TX Fast Ethernet WAN (Media Auto Sensing)1 Com Port (Dial-Up Modem)

nn

Ports

n

n COM

D-Link DI-804HV Broadband Hardware VPN Router · D-Link DI-804HV Broadband Hardware VPN Router...

Documents

Transcript of D-Link DI-804HV Broadband Hardware VPN Router · D-Link DI-804HV Broadband Hardware VPN Router...