d 1 Pneumatik 06 re - shop.lechler.de · 1.4 Pneumaticatomizingnozzles Spray Modeof Mixing Series...
Transcript of d 1 Pneumatik 06 re - shop.lechler.de · 1.4 Pneumaticatomizingnozzles Spray Modeof Mixing Series...
Atomization of viscous liquidsCoolingGas coolingHumidification of airHumidification of goodsLubricationWeb dampeningand many others...
Pneumatic
atomizing
nozzles
1.2
Pneumatic atomizing nozzles
Pneumatic atomizing nozzlesare available in various de-signs to comply with specificspray and flow requirements:
� self-aspiration (siphon prin-ciple)
� supply of liquid from a ves-sel located at a higher level(gravity principle)
� supply of liquid underpressure (pressure prin-ciple)
� mixing of fluids inside oroutside the nozzle
� full cone or flat fan spraypattern
For many applications, ad-justability of liquid flow and,thereby, of the droplet size, ispossible with the aid ofmanually operated accessorycomponents.A pneumatically controlledpiston (series 136) ormagnetic valve (series 166)allows to perform automatic orintermittent operations.A number of special custom-ized designs complete thenozzle range.
Criteria for selecting pneu-matic atomizing nozzles
1. Spray pattern
Pneumatic flat fan atomizingnozzles should be chosen forhumidifying and cooling ofgoods, for web dampeningand for a number of paintingtasks; in short, wherever abroad linear impact is requi-red. Pneumatic full coneatomizing nozzles, however,should be used, when a com-pact, circular impact or amajor reach is required, e.g.for direct air humidifying, forgas cooling or for chemicalprocess applications.
2. Mode of liquid supply
Whenever liquid can be sup-plied under pressure, it isrecommended to use nozzlesfunctioning by the liquidpressure principle. Use ofpneumatic atomizing nozzlesoperating to the siphon or thegravity principle is recom-mended when liquid is to besprayed in small quantities,e.g. for spraying of disinfect-ants.
3. Mixing of fluids
The supply of air or gas provi-des an additional breaking upof the liquid flow into finestdrop particles. This supplyand mixing can either takeplace inside or outside thenozzle. Inside mixing shouldbe preferred, when water, lowviscosity liquids or liquidswithout solid matter are to beatomized. Outside mixing isparticularly suited for atom-izing viscous liquids which areprone to impurities and there-fore tend to cause clogging ofthe nozzle. Low liquid pres-sures are used with this typeof nozzle due to its design.
Siphon principle Liquid pressure principle
Gravity principle Pressure principle with pneumaticallycontrolled valve (example)
Air
Liquid
Air
Liquid
Liquid
Liquid
mmWs
mmWs
Control air forpneumatic valve
1.3
Pneumatic atomizing nozzles
Spray Mode of Mixing Series V Water Application Pagepattern liquid of fluids [l/h]
supply<)
.
1.10
1.12
1.7
0,30 – 96,20 Web dampening,humidification ofgoods, cooling.
45°60°80°
Flatfan
Pressureprinciple
Inside
0,50 – 6,50 Web dampening,humidification ofgoods, cooling.
60°Flatfan
Siphon orgravityprinciple
Inside
1.51,50 – 172,70 Humidificationof air, cooling.
20°Fullcone
Pressureprinciple
Inside
1,80 – 80,70 Humidificationof air, cooling.
60°Fullcone
Pressureprinciple
Inside
1.90,40 – 43,70 Chemical industry,cooling, spraying ofviscous liquids.
20°Fullcone
Siphon orgravityprinciple
Out-side
136.4166.4
136.5166.5
136.1166.1
136.2166.2
136.3166.3
1.4
Pneumatic atomizing nozzles
Spray Mode of Mixing Series V Water Application Pagepattern liquid of fluids [l/h]
supply<)
.
1.16
On request.Please askfor our leaflet„TwinfluidNozzle
Lances“.
On request.Please askfor our leaflet„TwinfluidNozzleLances“.
140 4,50 – 12,00 Lubrication,cooling,humidification of air.
20°– 30°Fullcone
Siphon orgravityprinciple
Inside
170 8,50 – 290,00[l/min]
Gas cooling,flue gasdesulphurisation,exhaust gas condi-tioning,dust control.
15°Fullcone
Pressureprinciple
Inside
150 0,15 – 63,00[l/min]
Chemical processengineering, coo-ling, atomizing ofviscous liquids.
20°– 30°Fullcone
Pressureprinciple
Outside
1.13136.6166.6
2,00 – 94,10 Web dampening,humidification ofgoods, atomizationof viscous fluids.
45°60°
Flatfan
Pressureprinciple
Outside
Locking plug
Regulating/shut-off needle
Regulating/quick-cleaning
device
Pneumaticallycontrolled valve
Seal-ing
Nozzle body
Nozzle tip
Lockring
Fine full cone atomizationand fogging with air or gas.Liquid pressure principle.Internal mixing of fluids.Applications:Humidification of air, cooling.
Pneumatic atomizing nozzles,Full cone, pressure principle, internal mixingSeries 136.1/166.1
19,3mm
35,6mm
1/4BSPP
39,6 mm
Hex 13
Ø 42mm
136. 105. xx. 15166. 105. xx. 15
136. 104. xx. 15166. 104. xx. 15
136. 104. xx. 14166. 104. xx. 14
0,50
0,50
0,70
0,801,001,101,20--0,700,801,00--0,801,101,401,501,701,801,90
3,602,502,001,50--5,305,004,40--8,205,504,203,903,303,002,70
0,600,700,800,90--1,201,301,50--1,201,601,902,002,202,302,40
1,501,701,801,90--1,401,501,701,801,901,501,802,102,302,602,802,90
5,104,303,803,30--7,307,006,406,105,8011,709,607,506,605,604,904,50
0,801,001,001,10--1,802,002,102,202,301,802,102,502,702,903,103,20
2,802,903,003,303,403,602,903,003,203,303,402,502,803,003,303,603,904,10
7,006,606,305,204,904,109,208,908,508,308,1018,0016,2015,0013,1011,509,809,00
1,201,301,301,601,601,803,003,103,303,403,502,402,803,003,303,704,004,20
4,304,404,604,704,805,004,304,604,805,205,503,303,603,904,104,404,704,80
6,105,805,004,704,403,809,508,908,607,607,1020,4018,9017,3016,2014,7013,2012,80
1,902,002,102,202,302,404,204,504,705,105,403,003,303,703,904,304,604,70
0,801,702,503,004,30-0,801,402,302,904,301,502,302,903,304,10--
0,701,502,003,004,00-0,701,502,003,004,000,701,502,003,004,00--
4040404040-40404040404040404040--
5050606060-50506070808080808080--
��
��
��
��
��
��
Ordering no.
Type Mat.-no.
1.4305/303 SS
EØ[mm]
Liquid pressure p [bar] Spray dimensions
3516
Brass plated
D1 D2pAir
[bar]
pAir
[bar]
pAir
[bar]
pAir
[bar]
pWater
[bar]
V.Water
[l / h]
VWater
[l / h]
VWater
[l / h]
VWater
[l / h]
VnAir
[m3 / h]
VnAir
[m3 / h]
VnAir
[m3 / h]
VnAir
[m3 / h]
0,7 1,5 3,0 4,0
. . . . . . .pAir
[bar]
Example Type + Material no. (xx) = Ordering no.for ordering: 136. 105. xx. 15 + 35 = 136. 105. 35. 15
E = narrowest free cross section (water)
Weight brass: 200 g
Accessories for series 136, please refer to page 1.15
<)
300
150
D2
D1
<)
Spray angle
20°
Continued on next page.
1.5
Series 166.1 with magnetic valveWeight brass: 350 gSeries 136.1
Series 136.1/166.1
136. 103. xx. 13166. 103. xx. 13
136. 141. xx. 11166. 141. xx. 11
1,00
2,00
1,101,401,501,701,801,902,101,001,101,201,30---
13,3010,309,408,507,707,306,1034,9029,8025,4022,30---
2,603,103,303,703,904,004,303,604,004,504,80---
1,902,202,502,803,003,303,401,401,501,701,801,902,00-
20,7017,6014,7012,5011,109,508,7091,9082,7065,4057,9050,7045,20-
3,604,204,805,205,606,006,203,103,504,404,805,305,70-
3,303,804,505,205,505,90-2,502,803,003,203,303,503,80
29,5025,7019,7015,7014,1012,20-
143,60123,20108,4094,7088,1075,5061,50
5,406,207,508,609,109,80-4,005,105,906,807,208,109,40
-4,505,205,50---3,203,503,704,004,504,805,20
-32,0026,9024,90---
172,70154,10141,50123,4093,3077,8064,70
-7,108,208,80---4,505,606,407,609,7010,9012,70
1,702,803,805,205,90--0,701,503,004,00---
0,701,502,003,004,00--0,701,503,004,00---
4040404040--60808050---
6080808080--13013010090---
��
��
��
��
Ordering no.
Type Mat. no.
1.4305/303 SS
EØ[mm]
Liquid pressure p [bar] Spray dimensions
3516
Brass plated
D1 D2pAir
[bar]
pAir
[bar]
pAir
[bar]
pWater
[bar]
VWater
[l / h]
VWater
[l / h]
VWater
[l / h]
VWater
[l / h]
VnAir
[m3 / h]
VnAir
[m3 / h]
VnAir
[m3 / h]
VnAir
[m3 / h]
0,7 1,5 3,0 4,0
. . . . . . . .pAir
[bar]
<)
Spray angle
20°
Pneumatic atomizing nozzles, Full cone, pressure principle, internal mixingSeries 136.1 / 166.1
Example Type + Material no. (xx) = Ordering no.for ordering: 136. 103. xx. 13 + 16 = 136. 103. 16. 13
E = narrowest free cross section (water)
1.6
pAir
[bar]
Locking plug
Regulating/shut-off needle
Regulating/quick-cleaning
device
Pneumaticallycontrolled valve
Seal-ing
Nozzle body
Nozzle tip
Lockring
Pneumatic atomizing nozzles, Full cone, pressure principle, internal mixingSeries 136.2 / 166.2
Fine full cone atomizationand fogging with air or gas.Especially wide spray angleof 60°. Pressure principle.Internal mixing of fluids. Applications: Humidification of air, cooling. 35,6
mm
19,3mm
39,6mm
1/4BSPP
Hex 13
Ø 42mm
60°136. 206. xx. 15166. 206. xx. 15
136. 208. xx. 12166. 208. xx. 12
0,50
1,00
----0,700,800,901,001,101,20---
----2,102,503,003,504,104,60---
----
22,4017,2012,107,804,401,80---
1,401,501,701,801,401,501,701,801,90----
6,105,604,704,2035,1028,7020,3016,3011,70----
1,501,601,801,902,903,204,104,605,10----
2,903,203,303,402,802,903,003,203,303,403,603,703,80
7,406,405,905,6047,1040,4037,2030,2024,2021,9014,7011,707,30
2,602,903,003,104,704,805,306,206,907,208,308,809,60
4,104,504,805,204,304,504,805,20-----
7,506,205,103,5029,5023,1015,205,50-----
3,503,904,204,708,309,3010,5013,00-----
1,502,303,204,100,801,502,303,204,10----
1,502,003,004,000,701,502,003,004,00----
200200200200190200200200200----
300330330330360380380360360----
��
��
��
��
E = narrowest free cross section (water)
Ordering no.
Type Mat. no.
1.4305/303 SS
Spray angle
EØ[mm]
Liquid pressure p [bar] Spray dimensions
3516
Brass plated
<)
D1[mm]
D2[mm]p
Air
[bar]
pAir
[bar]
pAir
[bar]
pAir
[bar]
pWater
[bar]
VWater
[l / h]
VWater
[l / h]
VWater
[l / h]
VWater
[l / h]
VnAir
[m3 / h]
VnAir
[m3 / h]
VnAir
[m3 / h]
VnAir
[m3 / h]
0,7 1,5 3,0 4,0
. . . . . . . . .pAir
[bar]
Example: Type + Material no. (xx) = Ordering no.for ordering 136. 206. xx. 15 + 16 = 136. 206. 16. 15
Weight brass: 200 g
Accessories for series 136, please refer to page 1.15
300
D2D1
150
Continued on next page.
1.7
Series 136.2Series 166.2 with magnetic valve
Weight brass: 350 g
Series 136.2/166.2
Pneumatic atomizing nozzles, Full cone, pressure principle, internal mixingSeries 136.2 / 166.2
60°
136. 211. xx. 11166. 211. xx. 11
136. 209. xx. 12166. 209. xx. 12
1,40
1,50
1,701,801,902,102,202,302,501,201,501,801,902,102,202,30
5,205,505,706,206,406,707,104,805,606,406,707,207,407,60
25,4022,6020,7017,2015,3013,3010,6036,3032,4028,9027,9026,2025,3024,30
2,602,903,003,203,303,403,602,102,302,602,903,203,404,10
46,9038,2036,2031,7029,3027,3023,2052,9050,7047,4043,9040,7038,3030,10
6,807,607,808,308,608,909,306,907,408,209,009,7010,2011,90
4,104,504,805,205,50--4,104,504,805,20---
78,0067,2059,2050,2044,70--
69,8066,3063,4059,50---
9,0010,3011,1012,1013,00--
11,6012,7013,4014,50---
-------5,205,305,40----
-------
80,7080,0079,00----
-------
14,2014,5014,70----
0,801,502,303,20---0,801,502,303,204,10--
0,701,502,003,00---0,701,502,003,004,00--
230230220200---230220200200190--
430460430430---380380380360360--
��
��
��
��
E = narrowest free cross section (water)
Ordering no.
Type Mat. no.
1.4305/303 SS
Spray angle
EØ[mm]
Liquid pressure p [bar] Spray dimensions
3516
Brass plated
<)
D1[mm]
D2[mm]p
Air
[bar]
pAir
[bar]
pAir
[bar]
pAir
[bar]
pWater
[bar]
VWater
[l / h]
VWater
[l / h]
VWater
[l / h]
VWater
[l / h]
VnAir
[m3 / h]
VnAir
[m3 / h]
VnAir
[m3 / h]
VnAir
[m3 / h]
0,7 1,5 3,0 4,0
. . . . . . . . .pAir
[bar]
Example Type + Material no. (xx) = Ordering no.for ordering: 136. 211. xx. 11 + 16 = 136. 211. 16. 11
1.8
Locking plug
Regulating/shut-off-needle
Regulating/quick-cleaning
device
Pneumaticallycontrolled valve
Seal-ing
Nozzle body
Nozzle tip
Lockring
Particularly fine full coneatomization with air or gas.Siphon principle. Externalmixing of fluids. Applications: Chemical industry, cooling,atomization of viscous liquids.
Pneumatic atomizing nozzles, Full cone, siphon principle, external mixingSeries 136.3 / 166.3
32,5mm
19,3mm
39,6mm
1/4BSPP
Hex 13
Ø 42mm
E = narrowest free cross section (water)
Operational information:Liquid flow of pneumatic atomizing nozzles with external mixingcan be turned down to 0 with air pressure remaining constant.
Example Type + Material no. (xx) = Ordering no.for ordering: 136. 330. xx. 16 + 16 = 136. 330. 16. 16
Weight brass: 200 g
Accessories for series 136, please refer to page 1.15
<)
300
150
D2
D1
1.9
Series 136.3Series 166.3 with magnetic valve
Weight brass: 350 g
Series 136.3/166.3
Ordering no.
Type Mat. no.
1.4305/303 SS
Spray angle
EØ[mm]
V Water [l/h] Spray dimensions
3516
Brass plated
20°
<)
0,40
0,70
0,70
1,00
1,50
2,50
1,402,804,105,501,402,804,105,501,402,804,105,501,402,804,105,501,402,804,105,501,402,80
1,302,102,803,601,302,102,903,801,903,104,205,402,003,204,305,503,605,907,8010,006,209,90
1,902,102,202,405,606,507,207,105,305,304,603,408,909,709,809,9019,3016,8012,906,6043,7024,20
1,702,002,202,305,206,006,706,704,904,904,300,908,009,009,009,1017,4014,8010,503,6038,0019,50
1,501,802,002,204,705,506,306,304,404,503,900,607,208,208,408,5015,3012,307,80-
31,7015,60
1,101,401,802,103,504,505,105,703,603,801,00-5,506,506,707,1011,808,702,00-
21,204,50
1,001,401,702,003,004,004,605,403,203,400,90-4,105,605,906,2010,303,601,50-
18,30-
0,901,301,701,902,503,504,205,102,601,800,80-3,104,704,905,108,301,10--
16,00-
-0,901,401,70-2,003,004,301,200,900,50-1,302,702,802,800,40-----
--1,101,40-0,701,903,000,500,40---1,701,701,80------
1,402,804,105,501,402,804,105,501,402,804,105,501,402,804,105,501,402,804,105,501,402,80
606060605050505070606011050506050505050505050
1201101101101001101101101301201301101101001101009010010090110110
450
Vn
[m3/h]
p
[bar] 150300 100 200 300 600 900
pAir
[bar]
D1
[mm]
D2
[mm]
.
Water column[mm WS]
Aspiration height[mm WS]
.
Air
136. 330. xx. 16166. 330. xx. 16
136. 330. xx. 14166. 330. xx. 14
136. 329. xx. 14166. 329. xx. 14
136. 328. xx. 13166. 328. xx. 13
136. 327. xx. 12166. 327. xx. 12
136. 326. xx. 11166. 326. xx. 11
��
��
��
��
��
��
��
��
��
��
��
��
Locking plug
Regulating/quick-cleaning device
Regulating/quick-cleaning
device
Pneumaticallycontrolled valve
Seal-ing
Nozzle body
Nozzle tip
Lockring
Particularly fine flat fan ato-mization with air or gas.Siphon principle. Internalmixing of fluids. Applications: Web dampening, cooling,humidification of goods.
Pneumatic atomizing nozzles, Flat fan, pressure principle, internal mixingSeries 136.4 / 166.4
39,6mm
19,3mm
39,6mm
1/4BSPP
Hex 13
Ø 42mm
Ordering no.
Type Mat. no.
1.4305/303 SS
Spray angle
EØ[mm]
Liquid pressure p [bar] Spray dimensions
3516
Brass plated
45°
136. 417. xx. 14166. 417. xx. 14
136. 416. xx. 14166. 416. xx. 14
136. 415. xx. 13166. 415. xx. 13
<)
0,70
0,60
1,00
1,001,101,201,401,902,201,201,401,501,701,801,90-1,001,101,201,40---
7,406,706,104,802,501,604,202,802,201,301,000,30-
15,9014,9014,0011,80---
1,301,401,501,702,302,501,401,601,802,002,102,20-1,201,301,401,60---
1,501,802,102,302,903,302,102,302,502,602,802,903,002,102,302,502,602,802,903,00
12,5010,709,108,005,203,506,905,604,403,802,802,402,0020,4018,6016,6015,6013,7012,7011,90
1,601,902,202,403,003,402,002,202,502,602,802,903,002,102,302,402,502,702,802,90
3,003,303,704,105,90-3,804,104,504,805,20--3,804,104,504,805,20--
16,4014,9013,1011,404,90-
10,108,606,605,103,30--
26,9024,6021,6019,3016,50--
2,602,903,303,705,50-3,203,504,004,304,70--3,303,603,904,204,50--
4,504,805,205,50--5,205,505,906,20---5,205,505,90----
3,804,104,504,90--4,304,605,005,20---4,304,604,90----
1,402,303,203,70--1,502,603,204,105,50--1,102,102,803,604,80--
0,701,502,003,00--0,701,502,003,004,00--0,701,502,003,004,00--
60100100150--90130180240300--808090130140--
110150170230--140180230400480--130130130190220--
B1[mm]
B2[mm]p
Air
[bar]
pAir
[bar]
pAir
[bar]
pAir
[bar]
pAir
[bar]
pWater
[bar]
VWater
[l / h]
VWater
[l / h]
VWater
[l / h]
VWater
[l / h]
VnAir[m3 / h]
VnAir[m3 / h]
VnAir[m3 / h]
VnAir[m3 / h]
0,7 1,5 3,0 4,0
. . . . . . . .
��
��
��
��
��
��
E = narrowest free cross section (water) Continued on next page.
Example Type + Material no. (xx) = Ordering no.for ordering: 136. 416. xx. 14 + 16 = 136. 416. 16. 14
Weight brass: 200 g
Accessories for series 136, please refer to page 1.15
300150
B2
B1
16,4015,2013,6012,50--
10,609,207,606,10---
29,0027,0024,20----
1.10
Series 136.4Series 166.4 with magnetic valve
Weight brass: 350 g
Series 136.4/166.4
Pneumatic atomizing nozzles, Flat fan, pressure principle, internal mixingSeries 136.4 / 166.4
Ordering no.
Type Mat. no.
1.4305/303 SS
Spray angle
EØ[mm]
Liquid pressure p [bar] Spray dimensions
3516
Brass plated
60°
��
��
��
��
��
��
136. 446. xx. 15166. 446. xx. 15
136. 418. xx. 14166. 418. xx. 14
136. 442. xx. 11166. 442. xx. 11
<)
0,50
0,60
1,40
0,801,001,101,201,401,500,801,001,101,201,40--1,001,101,201,30---
1,501,802,102,302,602,801,401,701,902,102,202,302,501,801,902,002,10---
2,903,203,404,104,504,802,903,203,404,104,504,80-2,903,003,203,303,403,603,70
4,505,205,906,20--4,504,805,205,505,906,20-4,004,104,504,805,205,50-
B1[mm]
B2[mm]p
Air
[bar]
pAir
[bar]
pAir
[bar]
pAir
[bar]
pWater
[bar]
VWater
[l / h]
VWater
[l / h]
VWater
[l / h]
VWater
[l / h]
VnAir
[m3/ h]
VnAir
[m3/ h]
VnAir
[m3/ h]
VnAir
[m3/ h]
0,7 1,5 3,0 4,0
. . . . . . . .
80°
�� ��136. 414. xx. 13166. 414. xx. 13
0,80
1,101,201,401,501,70--
1,902,102,202,302,50--
3,203,403,603,703,904,004,10
4,504,805,205,505,90--
E = narrowest free cross section (water)
pAir
[bar]
Example Type + Material no. (xx) = Ordering no.for ordering: 136. 413. xx. 12 + 16 = 136. 413. 16. 12
1.11
45°
136. 413. xx. 12166. 413. xx. 12
1,10
0,801,001,101,201,401,501,701,801,902,10-
1,501,701,801,902,102,202,302,502,602,80-
3,403,704,004,104,304,404,604,704,805,005,20
4,704,805,205,50-------
�� ��
4,603,903,503,002,201,907,906,305,604,703,50--
15,9010,405,902,00---
9,808,405,804,101,10--
29,9024,2021,7019,7016,7015,1012,4011,2010,108,30-
1,101,401,501,601,801,901,001,201,301,401,70--4,204,905,506,10---
2,102,302,702,803,20--
1,802,202,502,703,103,303,703,904,004,40-
6,605,804,804,203,202,5012,4010,308,907,707,106,605,5033,9026,7021,4017,00---
15,8013,5012,5011,309,10--
45,1039,4036,8034,2030,2028,7026,8023,9022,6020,40-
1,702,002,202,402,702,901,301,601,802,102,202,302,505,406,106,707,30---
3,003,303,503,604,00--
2,603,003,203,403,804,004,304,604,805,20-
8,908,307,806,105,204,4015,8014,2013,209,608,006,70-
94,6084,0065,8057,8050,8038,2032,70
25,1023,0021,2020,1018,1017,3016,40
51,1045,2040,0038,7035,4034,3031,5030,5029,4027,3025,40
2,703,003,203,804,204,502,302,602,803,604,004,30-5,305,907,007,708,309,7010,30
4,204,504,805,005,305,505,60
5,205,806,406,507,007,107,507,707,908,308,60
8,907,505,905,30--
14,8013,5011,8010,509,208,20-
96,2086,6058,4042,1025,8016,50-
25,9023,3020,0017,6014,50--
54,4052,7046,2042,00-------
4,004,705,305,60--3,603,904,404,705,105,40-7,408,0010,5012,4014,9016,70-
5,706,106,807,307,90--
7,007,208,008,60-------
1,102,102,803,405,90-1,102,102,903,405,50--1,001,802,603,304,80--
1,402,202,903,705,20--
1,102,203,203,905,90------
0,701,502,003,004,00-0,701,502,003,004,00--0,701,502,003,004,00--
0,701,502,003,004,00--
0,701,502,003,004,00------
180230250300360-180200230280330--180230220280280--
240360360410430--
220220220280280------
300360410510560-300330360430530--300380360430430--
430610640710740--
330360360430430------
Locking plug
Regulating/quick-cleaning device
Regulating/quick-cleaning
device
Pneumaticallycontrolled valve
Seal-ing
Nozzle body
Nozzle tip
Lockring
Particularly fine flat fan ato-mization with air or gas.Siphon principle. Internalmixing of fluids. Applications: Web dampening, cooling,humidification of goods.
Pneumatic atomizing nozzles, Flat fan, siphon principle, internal mixingSeries 136.5 / 166.5
39,6mm
19,3mm
39,6mm
1/4BSPP
Hex 13
Ø 42mm
E = narrowest free cross section (water)Example Type + Material no. (xx) = Ordering no.for ordering: 136. 523. xx. 14 + 16 = 136. 523. 16. 14
Weight brass: 200 g
Accessories for series 136, please refer to page 1.15
300150
B2
B1
1.12
Series 136.5Series 166.5 with magnetic valve
Weight brass: 350 g
Series 136.5/166.5
Ordering no..
Type Mat. no.
1.4305/303 SS
Spray angle
EØ[mm]
Air V Water [l/h] Spray dimensions
3516
Brass plated
60° 136. 523. xx. 14166. 523. xx. 14
136. 522. xx. 14166. 522. xx. 14
136. 521. xx. 13166. 521. xx. 13
136. 519. xx. 13166. 519. xx. 13
<)
450
Vn
[m3/h]
p
[bar] 150300 100 200 300 600 900
pAir
[bar]
B1
[mm]
B2
[mm]
��
��
��
��
��
��
��
��
.
Water column[mm WS]
Aspiration height[mm WS]
.
0,70
0,70
0,90
1,00
0,701,502,001,502,001,502,003,003,501,502,003,003,504,00
1,602,503,002,803,402,202,703,604,101,902,303,203,604,00
3,903,603,002,301,705,504,803,703,006,506,104,403,603,70
3,503,302,702,101,504,804,203,402,705,905,604,003,803,50
3,203,002,501,901,304,403,903,202,505,204,903,603,803,30
2,702,702,301,701,104,003,602,602,004,203,903,903,402,90
2,502,702,301,601,003,603,402,401,903,703,603,703,302,80
2,302,602,301,500,903,303,102,201,703,303,603,703,302,80
1,502,302,101,100,502,502,401,701,302,403,103,002,602,20
1,101,901,800,80-1,601,701,200,601,502,402,402,101,80
0,701,502,000,701,501,502,003,003,501,502,003,003,504,00
250190180330360240210220210160160180180180
500390350670730480420430430320320350350350
Locking plug
Regulating/shut-off-needle
Regulating/quick-cleaning
device
Pneumaticallycontrolled valve
Seal-ing
Nozzle body
Nozzle tip
Lockring
Fine flat fan atomizationwith the aid of air or gas.Liquid pressure principle.External mixing of fluids. Applications: Web dampening, cooling,humidification of goods, ato-mization of viscous liquids.
Pneumatic atomizing nozzles, Flat fan, pressure principle, external mixingSeries 136.6 / 166.6
32,5mm
19,3mm
39,6mm
1/4BSPP
Hex 13
Ø 42mm
E = narrowest free cross section (water) Continued on next page.
Example Type + Material no. (xx) = Ordering no.for ordering: 13,6. 640. xx. 16 + 16 = 136. 640. 16. 16
Weight brass: 200 g
300150
B2
B1
1.13
Accessories for series 136, please refer to page 1.15
Series 136.6Series 166.6 with magnetic valve
Weight brass: 350 g
Series 136.6/166.6
Ordering no.
Type Mat. no.
1.4305/303 SS
Spray angle
EØ[mm]
Liquid pressure p [bar] Spray dimensions
3516
Brass plated
<)
B1[mm]
B2[mm]p
Air
[bar]
pAir
[bar]
pAir
[bar]
pAir
[bar]
VWater
[l / h]
VWater
[l / h]
VWater
[l / h]
VWater
[l / h]
VnAir
[m3 / h]
VnAir
[m3 / h]
VnAir
[m3 / h]
VnAir
[m3 / h]
0,07 0,15 0,30 0,35
. . . . . . . .pAir
[bar]
45°
136. 640. xx. 16166. 640. xx. 16
136. 640. xx. 15166. 640. xx. 15
136. 640. xx. 14166. 640. xx. 14
0,40
0,50
0,70
1,402,102,803,404,101,402,102,803,404,101,402,102,803,404,10
0,070,150,200,300,350,070,150,200,300,350,070,150,200,300,35
��
��
��
��
��
��
pWater
[bar]
60° 1,401,802,803,404,801,402,102,803,404,10
0,070,150,200,300,350,070,150,200,300,35
136. 639. xx. 16166. 639. xx. 16
136. 639. xx. 15166. 639. xx. 15
��
��
��
��
0,40
0,50
1,402,102,803,404,101,402,102,803,404,101,402,102,803,404,10
2,002,102,102,102,103,003,203,103,103,006,106,306,306,306,20
3,204,105,105,906,903,204,105,105,906,903,204,205,106,007,00
1,402,102,803,404,101,402,102,803,404,101,402,102,803,404,10
2,602,602,602,702,503,803,904,004,003,908,008,208,308,308,20
3,204,105,105,906,903,204,105,105,906,903,204,205,106,007,00
1,402,102,803,404,101,402,102,803,404,101,402,102,803,404,10
3,203,503,603,403,405,005,205,205,205,1010,8010,8010,9010,9010,80
3,204,105,105,906,903,204,205,105,906,903,204,205,106,006,90
1,402,102,803,404,101,402,102,803,404,101,402,102,803,404,10
3,703,703,703,803,705,505,505,505,505,5011,4011,6011,6011,6011,50
8080808080130150150150150150150150150150
150150150150150180200200230230230230250250250
3,204,105,005,906,903,204,205,105,906,903,204,205,106,006,90
-----1,402,102,803,404,10
-----2,903,003,002,902,80
-----4,005,206,407,408,60
1,402,102,803,404,101,402,102,803,404,10
2,502,502,602,502,503,803,803,803,803,70
4,005,206,307,308,504,005,206,407,508,60
1,402,102,803,404,101,402,102,803,404,10
3,303,403,303,303,305,105,105,105,105,00
4,005,106,307,308,504,005,206,407,408,60
1,402,102,803,404,101,402,102,803,404,10
3,503,603,503,503505,305,405,305,405,40
4,005,106,307,308,504,005,206,407,408,60
1009090100130909090100100
130110130150140130140140150150
Pneumatic atomizing nozzles, Flat fan, pressure principle, external mixingSeries 136.6 / 166.6
Operational information:Liquid flow of pneumatic atomizing nozz-les with external mixing can be turneddown to 0 with air pressure remainingconstant.
E = narrowest free cross section (water)Bestellbeispiel: Type + Material-Nr. (xx) = Bestellnummer
136. 639. xx. 14 + 16 = 136. 639. 16. 14
A1
A2
A3
1
2
A1
A2
A3
1
2
Liquid supply line
Control air for pneumatic valve
Atomizing air supply line
Pneumatically controlled valveOrdering no. 015. 601. xx. xx (see Page 1.15)
Pneumatic atomizing nozzleOrdering no. 136. 6xx. xx. xx (see Page 1.13 f)
Cereal dampening in a mixing drum
1.14
Ordering no.
Type Mat. no.
1.4305/303 SS
Spray angle
EØ[mm]
Liquid pressure p [bar] Spray dimensions
3516
Brass plated
<)
B1[mm]
B2[mm]p
Air
[bar]
pAir
[bar]
pAir
[bar]
pAir
[bar]
pWater
[bar]
VWater
[l / h]
VWater
[l / h]
VWater
[l / h]
VWater
[l / h]
VnAir[m3 / h]
VnAir[m3 / h]
VnAir[m3 / h]
VnAir[m3 / h]
0,07 0,15 0,30 0,35
. . . . . . . . .pAir
[bar]
60°
136. 639. xx. 14166. 639. xx. 14
136. 637. xx. 13166. 637. xx. 13
136. 634. xx. 12166. 634. xx. 12
136. 632. xx. 11166. 632. xx. 11
0,70
1,00
1,50
2,50
��
��
��
��
��
��
��
��
1,402,102,803,404,101,402,102,803,404,101,402,102,803,404,101,402,102,803,404,10
5,906,106,006,005,7011,0011,2011,1010,6010,2026,9026,5025,0023,6021,5042,9047,6051,7052,5051,30
4,005,306,407,508,709,1011,9014,7017,0019,609,6012,6015,5017,9020,8013,9018,2022,2025,9030,00
1,402,102,803,404,101,402,102,803,404,101,402,102,803,404,101,402,102,803,404,10
7,908,108,008,007,8014,2014,7014,5014,3013,7033,8034,0032,8031,8030,7056,7059,7064,4067,0066,70
4,005,206,507,508,709,2011,9014,6017,0019,709,7012,5015,4017,9020,8013,9018,1022,3025,8030,00
1,402,102,803,404,101,402,102,803,404,101,402,102,803,404,101,402,102,803,404,10
10,6010,7010,8010,7010,6018,9022,7019,1022,6018,6043,5043,7043,0042,7041,6084,9081,8080,3082,1083,10
4,005,206,407,508,709,1011,9014,6016,9019,709,7012,5015,4017,9020,9013,9018,1022,2025,9030,10
1,402,102,803,404,101,402,102,803,404,101,402,102,803,404,101,402,102,803,404,10
11,4011,4011,4011,4011,3019,9020,1020,3020,2019,9046,4046,5046,1045,3044,6094,1089,7087,0087,0087,50
4,005,306,407,508,709,2011,8014,6016,9019,709,6012,6015,5017,9020,8013,9018,1022,3025,8030,00
1,402,102,803,404,101,402,102,803,404,101,402,102,803,404,101,402,102,803,404,10
0,070,150,200,300,350,070,150,200,300,350,070,150,200,300,350,070,150,200,300,35
90130140140140140170180180180190200200190200150180180150150
130170180170190180220240240240330330330300300280290300280280
Example Type + Material no. (xx) = Ordering no.for ordering: 015. 602. xx. 01 + 16 = 015. 602. 16. 01 1.15
Accessories for pneumatic atomizing nozzles of the series 136.1 - 136.6
Ordering no.
For nozzlesType Mat. no.
1.4305 /
303 SS
3516
Brass
plated
015. 602. xx. 01015. 602. xx. 02015. 602. xx. 03015. 602. xx. 04015. 602. xx. 05015. 602. xx. 06
136.xxx.xx.11136.xxx.xx.12136.xxx.xx.13136.xxx.xx.14136.xxx.xx.15136.xxx.xx.16
��
��
��
��
��
��
��
��
��
��
��
��
Needle diameter D[mm]
2,41,41,00,70,50,3
015. 600 ��
Ordering no.
For nozzlesType Mat. no.
1.4305 /
303 SS
3516
Brass
plated
015. 601. xx. 01015. 601. xx. 02015. 601. xx. 03015. 601. xx. 04015. 601. xx. 05015. 601. xx. 06
136. xxx. xx. 11136. xxx. xx. 12136. xxx. xx. 13136. xxx. xx. 14136. xxx. xx. 15136. xxx. xx. 16
��
��
��
��
��
��
��
��
��
��
��
��
Needle diameter D[mm]
2,41,41,00,70,50,3
Ordering no.
Type Mat. no.
1.4305/303 SS
16
Ordering no.
For nozzlesType Mat. no.
1.4305 /
303 SS
3516
Brass
plated
015. 603. xx. 01015. 603. xx. 02015. 603. xx. 03015. 603. xx. 04015. 603. xx. 05015. 603. xx. 06
136. xxx. xx. 11136. xxx. xx. 12136. xxx. xx. 13136. xxx. xx. 14136. xxx. xx. 15136. xxx. xx. 16
��
��
��
��
��
��
��
��
��
��
��
��
Needle diameter D[mm]
2,41,41,00,70,50,3
For all nozzlesof the series 136
Quick-cleaning device
6268
D
SW 16
UNF 5 /16”-24
Pneumatically controlled valve.Opening pressure 2,1 bar, max. 180 cycles/min.
46
31
Luftanschluß
G 1/8 ISO 228
UNF 5 /16”-24D
Regulating device and shutting-off needle:
42,533,5*
UNF 5 /16”-24
UNEF 9/16”-24
SW 11/16 AF
* max. geöffneter Zustand
Regulating device with quick-cleaning needle
6066
D
SW 16
UNF 5 /16”-24
Weight brass: 51 g
Weight brass: 120 g
Weight: 1.4305 / 303 SS: 33 g
Weight brass: 75 g
Hex
1/8 BSPP
Air connection
Hex 16
Hex 16
max. opened
1.16
Particularly fine full coneatomization. Siphon princi-ple. Internal mixing of fluids.Integrated regulating device.Applications: Lubrication, cooling, humidifi-cation of air.
Pneumatic atomizing nozzles, Full cone, siphon principle, internal mixing Series 140
Ordering no.
Spray angle
V W = Liquid Vn A = AirEØ[mm]
Hs
Aspirationheight
Air
Water
20°-30° 140. 252. 30. 01
<)
0,750,50500200
-4,50
-2,50
4,507,00
4,004,00
8,0010,00
6,006,00
10,5012,00
[mm WS]
W
[l/h]
L
[m3/h]
W
[l/h]
L
[m3/h]
W
[l/h]
L
[m3/h]
W
[l/h]
8,008,00
L
[m3/h]
. .
p [bar] Air pressure0,5 1,0 2,0 3,0
E = narrowest free cross section (water)
Weight brass: 70 g
← Luft
Wasser →
Nipple014. 010. 30. 04(Material brass)Weight: 17 g
Accessories:
Gasket014. 040. 727,8 x 12 x 1 (EWP 210)
Assembly scheme
Air
Water