Cyclic prefix 1

Cyclic prefixIn telecommunications, the term cyclic prefix refers to the prefixing of a symbol with a repetition of the end.Although the receiver is typically configured to discard the cyclic prefix samples, the cyclic prefix serves twopurposes.• As a guard interval, it eliminates the intersymbol interference from the previous symbol.• As a repetition of the end of the symbol, it allows the linear convolution of a frequency-selective multipath

channel to be modelled as circular convolution, which in turn may be transformed to the frequency domain usinga discrete Fourier transform. This approach allows for simple frequency-domain processing, such as channelestimation and equalization.

In order for the cyclic prefix to be effective (i.e. to serve its aforementioned objectives), the length of the cyclicprefix must be at least equal to the length of the multipath channel. Although the concept of cyclic prefix has beentraditionally associated with OFDM systems, the cyclic prefix is now also used in single carrier systems to improvethe robustness to multipath propagation.

PrincipleCyclic prefix is often used in conjunction with modulation in order to retain sinusoids' properties in multipathchannels. It is well known that sinusoidal signals are eigenfunctions of linear, and time-invariant systems. Therefore,if the channel is assumed to be linear and time-invariant, then a sinusoid of infinite duration would be aneigenfunction. However, in practice, this cannot be achieved, as real signals are always time-limited. So, to mimicthe infinite behavior, prefixing the end of the symbol to the beginning makes the linear convolution of the channelappear as though it were circular convolution, and thus, preserve this property in the part of the symbol after thecyclic prefix.

Use in OFDMCyclic Prefixes are used in OFDM in order to combat multipath by making channel estimation easy. As an example,consider an OFDM system which has subcarriers.[1] The message symbol can be written as:

The OFDM symbol is constructed by taking the inverse discrete Fourier transform (IDFT) of the message symbol,followed by a cyclic prefixing. Let the symbol obtained by the IDFT be denoted by

.Prefixing it with a cyclic prefix of length , the OFDM symbol obtained is:

.Assume that the channel is represented using

.Then, after convolution with the channel, which happens as

which is circular convolution, as becomes . So, taking the Discrete FourierTransform, we get

.where is the discrete Fourier transform of . Thus, a multipath channel is converted into scalar parallel sub-channels in frequency domain, thereby simplifying the receiver design considerably. The task of channel

Cyclic prefix 2

estimation is simplified, as we just need to estimate the scalar coefficients for each sub-channel and once the valuesof are estimated, for the duration in which the channel does not vary significantly, merely multiplying the receiveddemodulated symbols by the inverse of yields the estimates of and hence, the estimate of actual symbols .

References[1] http:/ / www. create. ucsb. edu/ ATON/ 01. 01/ OFDM. pdf

• Fundamentals of Wireless Communication (http:/ / www. ifp. uiuc. edu/ ~pramodv/ book. html), by David Tseand Pramod Viswanath, Cambridge University Press (2005).

• A short tutorial on the significance of cyclic prefix in OFDM systems (http:/ / sites. google. com/ site/mdanishnisar/ pubs/ 01_OFDM_Tutorial_Nisar. pdf).

Article Sources and Contributors 3

Article Sources and ContributorsCyclic prefix  Source: http://en.wikipedia.org/w/index.php?oldid=579654648  Contributors: BD2412, BradBeattie, Brandon, Bucketsofg, Dogaroon, Elmsfu, Georgios Nikolaidis, Glenn,InvisibleK, Kumar Appaiah, Mange01, Mel aad, NigelKing, Oli Filth, R'n'B, Wiki contributor 21, 32 anonymous edits

LicenseCreative Commons Attribution-Share Alike 3.0//creativecommons.org/licenses/by-sa/3.0/