CX2200_Ver2.3_PNMSj configuration manual.pdf

PASOLINK NEO TECX2200

Multi-service Transport Gateway

Configuration File for PNMSj

MADE IN JAPAN

Revision History

Revision Date Change Description

A 2009/6/10 Initial release.

Notes Read this manual carefully before using it for the correct use. Keep this manual within easy reach after reading it. Reproduction of a part or the entire contents of this manual without prior consent is

prohibited. The contents of this manual may be changed without prior notice. Every effort has been made to ensure that the information in this manual is accurate. Any

discrepancies, errors, missing information, and suggestions should be reported to the distributor of the product or the NEC sales office.

NEC assumes no responsibility for the result of the operation. If you find any missing pages or pages out of order in this manual, please contact NEC

for a replacement. 1. Preface

This manual describes the configuration sample file of PASOLINK NEO TE CX2200 (referred to as CX2200 henceforth) Ver2.3 for Pasolink Network Management System (Java version) (referred as PNMSj henceforth). Refer to the CX2200 manual for the operation method of the CX2200 main body. This file is a sample file for monitoring CX2200 Ver2.3 using the MIB Loading function of PNMSj. Refer to the PNMSj manual for each function of PNMSj and the method of using the file. This file is available through the PNMSj license. For the procedure for obtaining the license, contact the distributor of the product or the nearest NEC sales office. This is only a sample file and does not guarantee the operation in the customer's environment. Change the configuration file according to the customer's environment when using it for operation.

2. Sample File Specification

This sample file is intended for CX2200 Ver2.3/PNMSJ Rev1.19. This sample file monitors the CX2200 status by classifying it into the following six categories.

Category Type Description

System Status Status Displays the device status.

System Fault Alarm Displays the device fault status. Layer2 Protocol Status Displays the Layer2 Protocol processing

status.

Reference Clock Status Displays the Reference Clock status. Port Status Status Displays the T1/E1 line status.

Port Link Status Status Displays the user line link status.

2.1. System Status

This category shows the device status. However, the items related to L2 Protocol and Reference Clock belong to a different category. The following items are monitored in this category.

Table 2.1 System Status monitoring items

Item Trap Status

CPUSW Status { Active/Active Fault CPUSW Type - CPUSW

Boot Cause - Power On Reset/Reset System Command/ WDT Abnormal/Fatal Error

LINE1 Type - 32T1E1H/1ATM155A/None/Unknown LINE2 Type - 2GBE/None/Unknown

FAN Status { Unmount/Mount(High) TRAP Message Discard { Normal/Discard Outband Port Status { Normal/Network Overload Inband Port Status { Normal/Network Overload

NTP Primary Access Status {

No Entry/No Memory/Bad Argument/ Device Address Setting Error/No Server/ Socket Error/Address Already In Use/ Bind Error/Ioctl Error/Timer Error/ Signal Error/Synchronization Failed/ Succeeded/No Access/Other Error

NTP Secondary Access Status {

No Entry/No Memory/Bad Argument/ Device Address Setting Error/No Server/ Socket Error/Address Already In Use/ Bind Error/Ioctl Error/Timer Error/ Signal Error/Synchronization Failed/ Succeeded/No Access/Other Error

SFP #25 { Unmount/SX/LX/XZ/BX-D10/BX-U10/ Other

SFP #26 { Unmount/SX/LX/XZ/BX-D10/BX-U10/ Other

SFP #1 { Unmount/S1.1/L1.1/L1.2/Other * SFP#1 is valid only when LINE1 is 1ATM155A.

2.2. System Fault

This category shows the device fault status. However, the items related to L2 Protocol and Reference Clock belong to a different category. The following items are monitored in this category.

Table 2.2 System Fault monitoring items

Item Severity Trap Normal (green) Fault (red)

Software Critical - Normal Critical/Warning Temperature Critical - Normal Critical/Warning

Processor Critical - Normal Critical

FAN #1 Major - Normal Major FAN #2 Major - Normal Major

FAN #3 Major - Normal Major

CPUSW Critical - Normal Critical/Major/Minor/Warning LINE1 Critical - Normal Critical/Major/Minor/Warning

LINE2 Critical - Normal Critical/Major/Minor/Warning

Power Input #1 Major - Normal Major Power Input #2 Major - Normal Major

CESoP Device Warning { Normal Fault IMA Group #1 Major { Up Down IMA Group #2 Major { Up Down IMA Group #3 Major { Up Down IMA Group #4 Major { Up Down IMA Group #5 Major { Up Down IMA Group #6 Major { Up Down IMA Group #7 Major { Up Down IMA Group #8 Major { Up Down SFP RX #25 Major { Normal Fault SFP RX #26 Major { Normal Fault SFP RX #1 Major { Normal Fault SFP TX #25 Major { Normal Fault SFP TX #26 Major { Normal Fault SFP TX #1 Major { Normal Fault SFP Device #25 Major - Normal Fault

SFP Device #26 Major - Normal Fault SFP Device #1 Major - Normal Fault

* SFP#1 is valid only when LINE1 is 1ATM155A.

2.3. Layer2 Protocol

This category shows the L2 Protocol processing status. The following items are monitored in this category.

Table 2.3 Layer2 Protocol monitoring items (1/2) Item Trap Status

STP Status - Disable/Enable

STP Port Role#17 { Disable Port/Alternate Port/Backup Port/ Root Port/Designated Port










LAG Port Status #17 { Active/Standby/Down/Block LAG Port Status #18 { Active/Standby/Down/Block LAG Port Status #19 { Active/Standby/Down/Block LAG Port Status #20 { Active/Standby/Down/Block LAG Port Status #21 { Active/Standby/Down/Block LAG Port Status #22 { Active/Standby/Down/Block LAG Port Status #23 { Active/Standby/Down/Block LAG Port Status #24 { Active/Standby/Down/Block LAG Port Status #25 { Active/Standby/Down/Block LAG Port Status #26 { Active/Standby/Down/Block

* Valid only when the L2Protocol is operated.

Table 2.3 Layer2 Protocol monitoring items (2/2)

Item Trap Status

Ring Port Status #25 { Initial State/RPL Block/Forward/Signal Fail/ Recovery/Wait To Restore

Ring Port Status #26 { Initial State/RPL Block/Forward/Signal Fail/ Recovery/Wait To Restore

Ring Node State #25 { Initial State/Idle/Protection Ring Node State #26 { Initial State/Idle/Protection

Ring Request #25 { Initial State/Local NR/Local SF/Remote NR/ Remote SF

Ring Request #26 { Initial State/Local NR/Local SF/Remote NR/ Remote SF

Ring Loop Detection #25 { None/Detect Ring Loop Detection #26 { None/Detect

* Valid only when the L2 Protocol function is operated. * As Ring Port Status/Ring Node State/Ring Request is notified only through one Trap, only

the Ring Port Status is immediately reflected by PNMSj. * The initial value of Ring Loop Detection is None and Trap notification is not performed.

Therefore, the status is not immediately reflected in PNMSj at Ring setting.

2.4. Reference Clock

This category shows the Reference Clock status of the device. The following items are monitored in this category.

Table 2.4 Reference Clock monitoring items Item Trap Status

Status { Normal/Aquiring Priority { 1/2/3/255 Supply Status #1 - Fault/Normal

Supply Status #2 - Fault/Normal

Supply Status #3 - Fault/Normal Multiple Source Supply Status #1 { Fault/Normal/Acquiring

Multiple Source Supply Status #2 { Fault/Normal/Acquiring

Multiple Source Supply Status #3 { Fault/Normal/Acquiring

1ATM155A Status - Not Running/Freerun/Holdover/Acquiring/ Acquired

* Multiple Source Supply Status is valid only the function is operated. * 1ATM155A Status is valid only when LINE1 is 1ATM155A.

2.5. Port Status

This category shows the T1/E1 line status of the device. The following items are monitored in this category.

Table 2.5 Port Status monitoring items

Item Trap Status

T1E1 #1 { Normal/LOS/AIS/LOF/RAI/LCD T1E1 #2 { Normal/LOS/AIS/LOF/RAI/LCD T1E1 #3 { Normal/LOS/AIS/LOF/RAI/LCD T1E1 #4 { Normal/LOS/AIS/LOF/RAI/LCD T1E1 #5 { Normal/LOS/AIS/LOF/RAI/LCD T1E1 #6 { Normal/LOS/AIS/LOF/RAI/LCD T1E1 #7 { Normal/LOS/AIS/LOF/RAI/LCD T1E1 #8 { Normal/LOS/AIS/LOF/RAI/LCD T1E1 #9 { Normal/LOS/AIS/LOF/RAI/LCD T1E1 #10 { Normal/LOS/AIS/LOF/RAI/LCD T1E1 #11 { Normal/LOS/AIS/LOF/RAI/LCD T1E1 #12 { Normal/LOS/AIS/LOF/RAI/LCD T1E1 #13 { Normal/LOS/AIS/LOF/RAI/LCD T1E1 #14 { Normal/LOS/AIS/LOF/RAI/LCD T1E1 #15 { Normal/LOS/AIS/LOF/RAI/LCD T1E1 #16 { Normal/LOS/AIS/LOF/RAI/LCD T1E1 #33 { Normal/LOS/AIS/LOF/RAI/LCD T1E1 #34 { Normal/LOS/AIS/LOF/RAI/LCD T1E1 #35 { Normal/LOS/AIS/LOF/RAI/LCD T1E1 #36 { Normal/LOS/AIS/LOF/RAI/LCD T1E1 #37 { Normal/LOS/AIS/LOF/RAI/LCD T1E1 #38 { Normal/LOS/AIS/LOF/RAI/LCD T1E1 #39 { Normal/LOS/AIS/LOF/RAI/LCD T1E1 #40 { Normal/LOS/AIS/LOF/RAI/LCD T1E1 #41 { Normal/LOS/AIS/LOF/RAI/LCD T1E1 #42 { Normal/LOS/AIS/LOF/RAI/LCD T1E1 #43 { Normal/LOS/AIS/LOF/RAI/LCD T1E1 #44 { Normal/LOS/AIS/LOF/RAI/LCD T1E1 #45 { Normal/LOS/AIS/LOF/RAI/LCD T1E1 #46 { Normal/LOS/AIS/LOF/RAI/LCD T1E1 #47 { Normal/LOS/AIS/LOF/RAI/LCD T1E1 #48 { Normal/LOS/AIS/LOF/RAI/LCD

2.6. Port Link Status

This category shows the user line link status of the device. The following items are monitored in this category.

Table 2.6 Port Link Status monitoring items (1/2)

Item Trap Status

#1 { Up/Down #2 { Up/Down #3 { Up/Down #4 { Up/Down #5 { Up/Down #6 { Up/Down #7 { Up/Down #8 { Up/Down #9 { Up/Down #10 { Up/Down #11 { Up/Down #12 { Up/Down #13 { Up/Down #14 { Up/Down #15 { Up/Down #16 { Up/Down #17 { Up/Down #18 { Up/Down #19 { Up/Down #20 { Up/Down #21 { Up/Down #22 { Up/Down #23 { Up/Down #24 { Up/Down #25 { Up/Down #26 { Up/Down

Table 2.6 Port Link Status monitoring items (2/2)

Item Trap Status

#33 { Up/Down #34 { Up/Down #35 { Up/Down #36 { Up/Down #37 { Up/Down #38 { Up/Down #39 { Up/Down #40 { Up/Down #41 { Up/Down #42 { Up/Down #43 { Up/Down #44 { Up/Down #45 { Up/Down #46 { Up/Down #47 { Up/Down #48 { Up/Down

3. Corresponding MIB 3.1. Private MIB

The following Private MIB items are monitored.

Table 3.1 Private MIB monitoring items (1/5) CX2200-100 specific MIB iems are shown below. private(4).enterprises(1).nec(119).necproduct(1).

Object identifier SYNTAX ACCESS Enumeration type DESCRIPTION TRAPsendcx2k [108] OBJECT IDENTIFIER NA

cx22-mbh [51] OBJECT IDENTIFIER NA

cx22-mbhSystem [1] OBJECT IDENTIFIER NA

cx22-mbhSystemCpusw [1] OBJECT IDENTIFIER NA

cx22-mbhSystemCpuswStatus [1] INTEGER RO active(3),active-fault(19) Status of CPUSW

cx22-mbhSystemCpuswOperType [2] INTEGER RO cpusw(256) Type of CPUSW

cx22-mbhSystemCpuswBootCause [8] INTEGER RO

power-on-reset(1),reset-system-command(3),the-status-of-WDT-is-abnormal(8),the-fatal-error-has-occurred(131)

Cause that system rebooted

cx22-mbhSystemLine [2] OBJECT IDENTIFIER NA

cx22-mbhSystemLineTable [1] OBJECT IDENTIFIER NA

cx22-mbhSystemLineEntry [1] OBJECT IDENTIFIER NA

cx22-mbhSystemLineIndex [1] INTEGER AFN

cx22-mbhSystemLineOperType [3] INTEGER RO

none(1),unknown(2),line1-16t1e1h(512),line1-1atm155a(513),line2-2gbe(768)

Type of LINE card

cx22-mbhSystemFanu [3] OBJECT IDENTIFIER NA

cx22-mbhSystemFanuOperStatus [1] INTEGER RO unmount(1),mount(2) Mount status of FAN module

cx22-mbhSystemMaintenance [11] OBJECT IDENTIFIER NA

cx22-mbhMessageDiscardedStatus [3] INTEGER RO normal(1),discarded(2) TRAP message discarded status

cx22-mbhTrap [4] OBJECT IDENTIFIER NA

cx22-mbhManagementPortTable [5] SEQUENCE OFcx22-mbhManagementPortEntry NA

cx22-mbhManagementPortEntry [1] cx22-mbhManagementPortEntry NA

cx22-mbhManagementPortIndex [1] INTEGER AFN Ifindex

cx22-mbhManagementPortStatus [2] INTEGER RO normal(1),network-overload(2) Management port status

cx22-mbhNtpAccessStatus [6] OBJECT IDENTIFIER NA

cx22-mbhNtpPrimaryAccessStatus [1] INTEGER RO

no-entry(1),no-memory(2),bad-argument(3),device-address-setting-error(4),no-server(5),socket-error(6),address-already-in-use(7),bind-error(8),ioctl-error(9),timer-error(10),signal-error(11),synchronization-failed(12),succeeded(16),no-access(3

NTP primary server access status

cx22-mbhNtpSecondaryAccessStatus [2] INTEGER RO

no-entry(1),no-memory(2),bad-argument(3),device-address-setting-error(4),no-server(5),socket-error(6),address-already-in-use(7),bind-error(8),ioctl-error(9),timer-error(10),signal-error(11),synchronization-failed(12),succeeded(16),no-access(3

NTP secondary server access status

cx22-mbhSessionStatusTable [7] SEQUENCE OFcx22-mbhSessionStatusEntry NA

cx22-mbhSystemResource [8] OBJECT IDENTIFIER NA

Page 13

Table 3.1 Private MIB monitoring items (2/5) cx22-mbhFltInf [2] OBJECT IDENTIFIER NA

cx22-mbhFltInfSystemSoftware [1] OBJECT IDENTIFIER NA

cx22-mbhFltInfSystemSoftwareSeverity [1] INTEGER RO

cl-none(1),cr(2),mj(3),mn(4),wr(5),if(6)

Severity of trouble1:Clear / Normal2:Critical3:Major4:Minor5:Warning6:Information

cx22-mbhFltInfSystemTemp [2] OBJECT IDENTIFIER NA

cx22-mbhFltInfSystemTempSeverity [1] INTEGER RO



cx22-mbhFltInfSystemProcessor [3] OBJECT IDENTIFIER NA

cx22-mbhFltInfSystemProcessorSeverity [1] INTEGER RO



cx22-mbhFltInfSystemFan [4] OBJECT IDENTIFIER NA

cx22-mbhFltInfSystemFanTable [1] SEQUENCE OFcx22-mbhFltInfFanEntry NA

cx22-mbhFltInfSystemFanEntry [1] cx22-mbhFltInfFanEntry NA

cx22-mbhFltInfSystemFanIndex [1] INTEGER AFN

cx22-mbhFltInfSystemFanSeverity [2] INTEGER RO



cx22-mbhFltInfCpuswDevice [5] OBJECT IDENTIFIER NA

cx22-mbhFltInfCpuswDeviceSeverity [1] INTEGER RO



cx22-mbhFltInfLineDevice [6] OBJECT IDENTIFIER NA

cx22-mbhFltInfLineDeviceTable [1] SEQUENCE OFcx22-mbhFltInfLineDeviceEntry NA

cx22-mbhFltInfLineDeviceEntry [1] cx22-mbhFltInfLineDeviceEntry NA

cx22-mbhFltInfLineDeviceIndex [1] INTEGER RO

cx22-mbhFltInfLineDeviceSeverity [2] INTEGER RO



cx22-mbhFltInfExternalMemory [7] OBJECT IDENTIFIER NA

cx22-mbhFltInfSystemPower [8] OBJECT IDENTIFIER NA

cx22-mbhFltInfSystemPowerTable [1] SEQUENCE OFcx22-mbhFltInfSystemPowerEntry NA

cx22-mbhFltInfSystemPowerEntry [1] cx22-mbhFltInfSystemPowerEntry NA

cx22-mbhFltInfSystemPowerIndex [1] INTEGER AFN

cx22-mbhFltInfSystemPowerSeverity [2] INTEGER RO



Page 14

Table 3.1 Private MIB monitoring items (3/5) cx22-mbhPathControl [3] OBJECT IDENTIFIER NA

cx22-mbhL2Protocol [4] OBJECT IDENTIFIER NA

cx22-mbhStp [1] MODULE-IDENTITY -

cx22-mbhStpExt [1] OBJECT IDENTIFIER NA

cx22-mbhStpModuleStatus [1] INTEGER RO disabled(1),enabled(2)

Spanning-tree Mode Status1:disabled,2:enabled

cx22-mbhStpPortExtTable [2] SEQUENCE OFcx22-mbhRstPortExtEntry NA

cx22-mbhStpPortExtEntry [1] cx22-mbhStpPortExtEntry NA

cx22-mbhStpPort [1] INTEGER AFN ifIndex

cx22-mbhStpPortRole [2] INTEGER RO

disabledPort(1),alternatePort(2),backupPort(3),rootPort(4),designatedPort(5)

Spanning-tree Port Role1:disabledPort,2:alternatePort,3:backupPort,4:rootPort,5:designatedPort

cx22-mbhStpTrapsControl [2] OBJECT IDENTIFIER NA

cx22-mbhLag [2] OBJECT IDENTIFIER NA

cx22-mbhLagPortTable [2] SEQUENCE OFcx22-mbhLagEntry NA

cx22-mbhLagPortEntry [1] cx22-mbhLagEntry NA

cx22-mbhLagPort [1] INTEGER AFN ifIndex

cx22-mbhLagPortStatus [2] INTEGER RO

active(1),standby(2),down(3),block(4)

LAG port Stateblock : port is disableddown : port is in linkdown stateact or sby: port is in linkup state

cx22-mbhLagTable [3] SEQUENCE OFcx22-mbhLagEntry NA

cx22-mbhInterface [5] OBJECT IDENTIFIER NA

cx22-mbhInterfaceSfp [1] OBJECT IDENTIFIER NA

cx22-mbhInterfaceSfpTable [1] SEQUENCE OFcx22-mbhInterfaceSfpEntry NA

cx22-mbhInterfaceSfpEntry [1] cx22-mbhInterfaceSfpEntry NA

cx22-mbhInterfaceSfpIndex [1] INTEGER AFN

cx22-mbhInterfaceSfpStatus [2] INTEGER RO

unmount(1),sx(2),lx(3),zx(4),oc3-si15(5),oc3-sl40(6),oc3-sl80(7),bx-d10(8),bx-u10(9),other(256)

Status of sfp moduleType of sfp module (If sfp module is mounted)

cx22-mbhInterfaceSfpRxError [3] INTEGER RO fault(1),normal(2) Received optical ray status of sfp module

cx22-mbhInterfaceSfpTxError [4] INTEGER RO fault(1),normal(2) Transmitted optical ray status of sfp module

cx22-mbhInterfaceSfpFault [2] OBJECT IDENTIFIER NA

cx22-mbhInterfaceSfpFaultTable [1] SEQUENCE OFcx22-mbhInterfaceSfpFaultEntry NA

cx22-mbhInterfaceSfpFaultEntry [1] cx22-mbhInterfaceSfpFaultEntry NA

cx22-mbhInterfaceSfpFaultIndex [1] INTEGER AFN

cx22-mbhInterfaceSfpFaultStatus [2] INTEGER RO fault(1),normal(2) Status of sfp error

cx22-mbhCounter [6] OBJECT IDENTIFIER NA

cx22-mbhAtmCounter [7] OBJECT IDENTIFIER NA

cx22-mbhAtmOam [8]

Page 15

Table 3.1 Private MIB monitoring items (4/5) cx22-mbhReferenceClock [9] OBJECT IDENTIFIER NA

cx22-mbhReferenceClockStatus [1] INTEGER RO normal(2),acquiring(3)2:normal3:acquiring

cx22-mbhReferenceClockPriority [2] INTEGER RO Clock Priority

cx22-mbhReferenceClockSupply [3] OBJECT IDENTIFIER NA

cx22-mbhReferenceClockSupplyStatusTable [1] SEQUENCE OF cx22-mbhReferenceClockSupplyStatusEntry NA

cx22-mbhReferenceClockSupplyStatusEntry [1] cx22-mbhReferenceClockSupplyStatusEntry NA

cx22-mbhReferenceClockSupplyStatusPriorityIndex [1] INTEGER AFN Clock Priority

cx22-mbhReferenceClockSupplyStatus [2] INTEGER RO fail(1),normal(2)

1:fail2:normal

cx22-mbhReferenceClockMultipleSourceSupply [4] OBJECT IDENTIFIER NA

cx22-mbhReferenceClockMultipleSourceSupplyStatusTable [1]SEQUENCE OF cx22-mbhReferenceClockMultipleSourceSupplyStatusEntry

NA

cx22-mbhReferenceClockMultipleSourceSupplyStatusEntry [1]cx22-cx22-mbhReferenceClockMultipleSourceSupplyStatusEntry

NA

cx22-mbhReferenceClockMultipleSourceSupplyStatusGroupInde [1] INTEGER AFN Reference Clock Group.

cx22-mbhReferenceClockMultipleSourceSupplyStatus [2] INTEGER ROfail(1),normal(2),acquiring(3)

1:fail2:normal3:acquiring

cx22-mbhEtherOamMIB [10] OBJECT IDENTIFIER NA

cx22-mbhT1E1Oam [11] OBJECT IDENTIFIER NA

cx22-mbhT1E1OamStatusTable [1] SEQUENCE OF cx22-mbhT1E1OamStatusEntry NA

cx22-mbhT1E1OamStatusEntry [1] cx22-mbhT1E1OamStatusEntry NA

cx22-mbhT1E1OamStatusIndex [1] INTEGER AFN Ifindex

cx22-mbhT1E1OamPortStatus [2] INTEGER RO

normal(1),los(2),ais(3),lof(4),rai(5),lcd(6)

cx22-mbhTdmOam [12] OBJECT IDENTIFIER NA

cx22-mbhAtm155 [13] OBJECT IDENTIFIER NA

cx22-mbhAtm155AdaptiveClockStatusTable [1] SEQUENCEOF cx22-mbhAtm155AdaptiveClockStatusEntry NA

cx22-mbhAtm155AdaptiveClockStatusEntry [1] cx22-mbhAtm155AdaptiveClockStatusEntry NA

cx22-mbhAtm155AdaptiveClockStatusIndex [1] INTEGER AFN

Card kind index100: line1200: line2300: cpusw

cx22-mbhAtm155AdaptiveClockGroupStatus [2] INTEGER RO

not-running(1),freerun(2),holdover(3),acquiring(4),acquired(5)

cx22-mbhAtmKeepalive [14] OBJECT IDENTIFIER NA

cx22-mbhAtmLoopbackCellOverload [15] OBJECT IDENTIFIER NA

cx22-mbhAtmIma [16] OBJECT IDENTIFIER NA

cx22-mbhAtmImaGroupStatusTable [1] SEQUENCE OFcx22-mbhAtmImaGroupStatusEntry NA

cx22-mbhAtmImaGroupStatusEntry [1] cx22-mbhAtmImaGroupStatusEntry NA

cx22-mbhAtmImaGroupStatusIndex [1] INTEGER AFN IMA Group index

cx22-mbhAtmImaGroupTrafficStatus [2] INTEGER RO down(1),up(2)

Page 16

Table 3.1 Private MIB monitorin gitems (5/5) cx22-mbhCesop [17] OBJECT IDENTIFIER NA

cx22-mbhCesopDeviceStatusTable [1] SEQUENCE OFcx22-mbhCesopDeviceStatusEntry NA

cx22-mbhCesopDeviceStatusEntry [1] cx22-mbhCesopDeviceStatusEntry NA

cx22-mbhCesopDeviceStatusIndex [1] INTEGER AFN

Card kind index100: line1200: line2300: cpusw

cx22-mbhCesopDeviceStatus [2] INTEGER RO normal(1),fault(2)

cx22-mbhEtherRing [18] OBJECT IDENTIFIER NA

cx22-mbhEtherRingStatusTable [1] SEQUENCE OF cx22-mbhEtherRingStatusEntry NA

cx22-mbhEtherRingStatusEntry [1] cx22-mbhEtherRingStatusEntry NA

cx22-mbhEtherRingStatusIndex [1] INTEGER AFN Index

cx22-mbhEtherRingStatusPortIndex [2] INTEGER AFN ifindex

cx22-mbhEtherRingStatusEthRingPortState [3] INTEGER RO

initial-state(1),rpl-block(2),forward(3),signal-fail(4),recovery(5),wait-to-restore(6)

Ether-Ring Port State

cx22-mbhEtherRingStatusEthRingNodeState [4] INTEGER ROinitial-state(1),idle(2),protection(3)

Ether-Ring Node State

cx22-mbhEtherRingStatusEthRingRequest [5] INTEGER RO

initial-state(1),local-nr(2),local-sf(3),remote-nr(4),remote-sf(5)

Ether-Ring Status Cause

cx22-mbhEtherRingPortInformationTable [2] SEQUENCE OF cx22-mbhEtherRingPortInformationEntry NA

cx22-mbhEtherRingPortInformationEntry [1] cx22-mbhEtherRingPortInformationEntry NA

cx22-mbhEtherRingPortInformationPortIndex [1] INTEGER AFN ifindex

cx22-mbhEtherRingLoopDetection [2] INTEGER RO none(1),detect(2) Loop Detection

Page 17

3.2. Standard MIB

The following Standard MIB items are monitored.

Table 3.2 Standard MIB monitoring items Standard MIB items RFC1213 are shonw below.

Object identifier SYNTAX ACCESS DESCRIPTION TRAP sendiso(1).org(3).dod(6).internet(1). - OBJECT IDENTIFIER -

mgmt(2). - OBJECT IDENTIFIER -

mib2 [1] OBJECT IDENTIFIER -

system [1] OBJECT IDENTIFIER -interfaces [2] OBJECT IDENTIFIER -

ifNumber [1] INTEGER RO

ifTable [2] SEQUENCE OFIfEntry NA

ifEntry [1] IfEntry NA INDEX { ifIndex }ifIndex [1] INTEGER RO

ifOperStatus [8] INTEGER RO

Page 18

4. Known Limitations

NO Restriction Assumed problem Work-around

1 Multiple items cannot be updated concurrently with one Trap.

Even if Trap detection is performed for a Layer2 Protocol monitoring item, the item status may not be updated.

Perform Get all/Connection Check/Slow polling. Alternatively, the item status is updated automatically at the polling cycle.

2 Multiple severities cannot be set for one item.

See the left column.

None In the sample file, the highest possible severity for the item is set.

Notes1. Preface2. Sample File Specification2.1. System Status2.2. System Fault2.3. Layer2 Protocol2.4. Reference Clock2.5. Port Status2.6. Port Link Status

3. Corresponding MIB3.1. Private MIB3.2. Standard MIB

4. Known Limitations

CX2200_Ver2.3_PNMSj configuration manual.pdf

Documents

Transcript of CX2200_Ver2.3_PNMSj configuration manual.pdf