CUSTOM THERMISTOR SENSOR
Transcript of CUSTOM THERMISTOR SENSOR
CU
ST
OM
SE
NS
OR
SO
LU
TIO
NS
CUSTOM
THERMISTOR SENSOR SOLUTIONS
CAT.NO.137B
Body Temperature Measurement
・ Fμ Sensor
・ 503ET-3H87U
・ FT-ZM
Non Contact Sensors
・ NC Sensor
・ Thermopile Module
・ HF-N Sensor
・ Thermopile
OA Equipment
・ Printer / Copy Machine
Industrial Equipment
・ Liquid Temperature Measurement
・ Pipe Temperature Measurement
・ Heat sink
・ Cooking Appliances
・ Heater Temperature Measurement
Home Appliances
・ Air Conditioning
・ Refrigerator
・ Microwave Oven
・ Water Heater / Warm Water Toilet Seat
・ Power Conditioner
・ Rechargeable Battery
・ Fire Alarm
Medical
・Catheter
・Thermometer / Ear Thermometer
・ Controller Unit
・ Motor
・ Battery / Capacitor
Screw Mount Sensor
・ Screw Mount Sensor
・ Flange Pipe Sensor
2
Standard Assembly Products
・Stock Items
Low Temperature
・ Pipe Sensor
・ Dip Sensor
High Temperature
・ FS, HF Sensor
・ Teflon Tube Sensor
・ Flange Pipe Sensor
・ Screw Mount Sensor
・ Screw Pipe Sensor
Liquid Measurement
・ SUS 3 Level Pipe Sensor
・ SUS Pipe Sensor
・ Screw Pipe Sensor
Screw Type Sensors
・ Screw Type Pipe Sensor
Surface Measurement Sensors
・ FS, HF Sensor
・ FT-ZM
・ Standard Assembly
INDEX
P4 - 5
P6 - 7
P8
P9 - 11
P12 - 13
P14 - 15
①
②
③
NON CONTACT
⑬
⑬
⑭
⑮
⑰ ⑲
㉑
㉖ ㉘
④ ⑤ ⑥
⑪
㉒ Ⓕ
㉝
㉓
㉔
㉘
⑦ ⑧ ⑨ ㉒ ㉕ ㉚ ㉜ Ⓑ Ⓒ Ⓔ Ⓕ
㉑ ㉛
⑩ ㉘ ㉝
④ ⑤ ⑥
⑮
Ⓓ
By application By characteristics
High Accuracy
High
Speed
Ultra Small
High Speed
Automotive
This catalog contains a selection of representative products. Please contact us if you need your own custom sensor solution.
We recommend to check below items before selecting a sensor
3
■ Purpose / Environment 1) In what kind of device will it be used?
Device: (E.g.: Outside unit of air conditioning, inside of a refrigerator 2) How will it be mounted?
Mounting: (E.g.: Mounted with holder on a pipe 3) In what kind of environment will it be used?
Environment: (E.g.: Room temperature, max. temperature 180℃, etc. 4) Are there other requirements regarding responsiveness, temperature accuracy, etc.?
Others:(
■ Temperature 1) The temperature range in which the product or sensor is used is ( )℃ to ( )℃. 2) Temperature to be measured or temperature to be controlled is ( )℃ to ( )℃.
■ Characteristics 1) Desired resistance value (Zero Power Resistance)
( kΩ ±( )% at ( )℃ 2) B Value (Calculated from the resistances at 2 temperature points)
( )K ± ( )% Temperature ( )℃, ( )℃ 3) Electrical performance
Withstand voltage ( )V ( )sec.
Insulation resistance ( )Ω
)
)
)
Simply said this is a circuit that converts the
temperature of the thermistor into voltage.
(R2 and C1 are noise filters)
For the thermistor R1 the voltage is measured in
a voltage-dividing circuit RTH using a Peripheral
Interface Controller (below PIC).
The electric current to the PIC is minimal and can
be ignored.
■ Temperature – Voltage Conversion Circuit
Basic Thermistor Characteristics & Application Circuit Example
■ Resistance – Temperature Characteristics
The relationship between resistance and temperature
within a given temperature range is approximately as
in the formula 1 below.
R1=R2exp[B( - )] T1 T2
1 1 (Formula 1)
T1, T2
R1, R2
B
: Absolute temperature(K)
: Zero Power Resistance(Ω) at T1,T2
: B value (K)
)
Thermistor
R1, C1 are noise, filter.
Time constant = C x R = 47ms
Features: A non contact Sensor based on infrared detection that
has very strong heat and dirt resistance.
◆Thermal Time Constant: approx. 46ms
4
①NC Sensor
OA Equipment
Printer / Copy Machine
Non Contact
◆Thermal Time Constant: approx. 1.3 sec. ◆Dielectric Strength Voltage: AC 500V 1 sec.
◆Insulation Resistance: DC500V 100MΩ+
※1: Without connector
②Thermopile Module
③HF-N Sensor
Unit: mm
Zero Power Resistance R180 = 7kΩ±5% :
B value B25/85 = 3370K±3% :
Temperature range -20℃ - 230℃ (Sensing part) :
Source Voltage 3.2V - 6V :
Temperature range -25℃ - 100℃ :
Non Contact
Unit: mm
B value B25/85 = 3370K±1% : ※1 -10℃ - 150℃ Temperature range :
Zero Power Resistance R180 = 7kΩ±5% :
: Measurement temp. range -10℃ - 260℃
Output Voltage 0.2V - 2.8V :
Measurement temp. range -20℃ - 250℃ :
Features: A non contact Sensor based on infrared detection that
measures temperature easily and accurately.
Non Contact
Unit: mm
Features: A Sensor that allows non contact measurement with
conventional thermistor systems.
Leads Connector
Thermopile
Connector
Leads Connector
5
④FS Sensor
OA Equipment
◆Thermal Time Constant: approx. 1.0 sec. (roller) ◆Dielectric Strength Voltage: AC 600V 1 sec.
◆Insulation Resistance: DC 500V 100MΩ+
Zero Power Resistance R180 = 7kΩ±5% :
B value B25/85 = 3370K±3% :
Temperature range -20℃ - 230℃ (Sensing part) :
⑤HF-H Sensor
◆Thermal Time Constant: approx. 0.7 sec. (roller) ◆Dielectric Strength Voltage: AC600V 1 sec.
◆Insulation Resistance: DC 500V 100MΩ+
Zero Power Resistance R180 = 7kΩ±5% :
B value B25/85 = 3370K±3% :
Temperature range -20 - 230℃ (Sensing part) :
⑥HF-L Sensor
◆Thermal Time Constant: approx. 1.0 sec. (roller) ◆Dielectric Strength Voltage: AC600V 1 sec.
◆Insulation Resistance: DC 500V 100MΩ+
Features: A low friction type sensor that reduces damage to the fuser roller
to a minimum.
Features: A high speed type temperature sensor that can quickly respond to
temperature changes of the fuser roller.
Features: A space saving type of temperature sensor with lead wires parallel
to the fuser roller.
Lead
Wire
Zero Power Resistance R180 = 7kΩ±5% :
B value B25/85 = 3370K±3% :
Temperature range -20 - 230℃ (Sensing part) :
Unit: mm
Unit: mm
Unit: mm
Connector Leads
Leads Connector
Connector Leads
⑦Screw Mount Sensor
Automotive
Controller Unit
◆Thermal Time Constant: approx. 75 sec.
◆Dielectric Strength Voltage: AC 600V 1 sec.
◆Insulation Resistance: DC 500V 100MΩ+
Zero Power Resistance R75 = 7.214kΩ±5% : B value B0/100 = 3970K±2% : Temperature range -40℃ - 130℃ :
⑧Screw Mount Sensor
6
Features: A screw mount type temperature sensor with very good heat
conductivity that allows the sensing of high temperatures.
Features: A screw mount type temperature sensor with very good heat
conductivity that allows highly accurate sensing of high temperatures.
⑨Screw Mount Sensor
◆Thermal Time Constant: 80 sec. max. ◆Dielectric Strength Voltage: AC 600V 1 sec.
◆Insulation Resistance: DC 500V 100MΩ+
B value B25/85 = 3182K±1% :
Features: A temperature sensor that resists screw tension and can therefore be
used for a long time.
黄銅リング
-40℃ - 90℃ : Temperature range
Zero Power Resistance R25 = 2kΩ±1% :
◆Thermal Time Constant: approx. 80 sec.
◆Dielectric Strength Voltage: AC 1800V 1 sec.
◆Insulation Resistance: DC 500V 100MΩ+
B value B25/85 = 3435K±0.5% :
Zero Power Resistance R25 = 10.0kΩ±0.5% :
Temperature range -40℃ - 125℃ :
Resin Form
Unit: mm
Unit: mm
Unit: mm
L1
L2
Screw Mount (brass) Polyimide Tube
Tin Plating
Polyimide (Glass)
Screw Mount
(Brass) Epoxy
Wire (PVC)
Brass Ring Tin Plating
R25 = 10.0kΩ±1%
◆Thermal Time Constant: approx. 25 sec.
◆Dielectric Strength Voltage: AC 2160V 1 sec.
◆Insulation Resistance: DC500V 100MΩ+
(2) L
⑩Screw Type Pipe Sensor
Automotive
Motor
◆Thermal Time Constant: approx. 298 sec.
◆Dielectric Strength Voltage: AC 600V 1 sec.
◆Insulation Resistance: DC 500V 100MΩ+
Zero Power Resistance R25 = 10.0kΩ±0.5% :
⑪Teflon Tube Sensor
◆Thermal Time Constant: 7 sec.
◆Dielectric Strength Voltage: AC 1200V 1 sec.
◆Insulation Resistance: DC 500V 100MΩ+
7
Features: A screw type temperature sensor with high accuracy and excellent
climate resistance.
Features: A temperature sensor with a thin tip and excellent responsiveness.
Connector
※1:without connector
Temperature range -40℃ - 150℃ :
※1
B value B25/85 = 3435K±0.5% :
⑫Slim Case Sensor
B value B25/85 = 3435K±1% :
Features: A slim case sensor with high electric strength voltage that fits
easily into narrow spaces.
ケース
Lead Wire (35.5)
(9.9
)
Temperature range -20℃ - 80℃ :
Zero Power Resistance :
Zero Power Resistance R100 = 1.0kΩ±5% :
Temperature range -40℃ - 250℃ :
B value B0/100 = 3387K±2% :
Battery / Capacitor
Unit: mm
Unit: mm
Unit: mm
Brass Ring
Screw Case (Brass) Epoxy Tube
(Glass) Wire
(PVC)
Wire (PFA) Shrink Tube (PFA) Thermistor Silicon
Case
-20℃ - 100℃
Thermistor B value
Output Voltage
3435K±0.7%
Unit: mm
GroupR37 (kΩ )
Min/Center/MaxGroup
R37 (kΩ )Min/Center/Max
A 29.614/29.629/29.644 B 29.645/29.660/29.675C 29.676/29.691/29.706 D 29.707/29.722/29.737・・
・・
S 30.172/30.187/30.202 T 30.203/30.218/30.233U 30.234/30.249/30.264
⑬Fμ Sensor
Catheter
Zero Power Resistance R37 = 14.054kΩ±0.5% :
B value B0/50 = 3454K±1% :
Temperature range -10℃ - 70℃ :
⑭503ET-3H87U
◆Thermal Time Constant: approx. 5.0 sec.
⑮FT-ZM
Zero Power Resistance R25 = 50.00kΩ±5% :
B value B25/85 = 3435K±1% :
Temperature range -10℃ - 100℃ :
⑯Thermopile
High Speed
Ultra Small
8
High
Accuracy
Features: Ultra small temperature sensor with high response speed.
Features: Small and highly accurate sensor optimized for
body temperature measurement.
Features: Small temperature sensor with high response speed
optimized for measuring surface temperatures.
Features: Non contact temperature sensor using infrared measuring Non Contact
◆Thermal Time Constant: approx. 0.07 sec.
(in water)
Temperature range : -40℃ - 100℃
R37 = 29.614 - 30.264kΩ Zero Power Resistance :
Group temp. tolerance R37±0.05% / Group :
B value B32/41 = 3943K±0.5% :
●R37 Group (A - U)
◆Thermal Time Constant: approx. 15ms
◆Angle : ±50deg.
◆Transparent wavelength band: Cut on 5μm
R25 = 100kΩ±3% Thermistor Resistance :
:
1.00±30mV :
Temperature range :
Thermometer / Ear Thermometer
Unit: mm
◆Thermal Time Constant: approx. 1.5 sec.
Unit: mm
Unit: mm
Solder Coated Urethane CP Wire (0.12
diameter)
Coated Polyurethane 0.08 CP Wire
Aluminum
Epoxy Solder
Polyimide AWG38 Polyesterimide Coating
Medical
Temperature range : -35℃ - 35℃
⑰Copper Pipe Sensor
エアコン
◆Thermal Time Constant: approx. 8 sec.
(in stirred water)
◆Dielectric Strength Voltage: AC 2200V 1 sec.
◆Insulation Resistance: DC 500V 100MΩ+
Refrigerator
9
⑱Dip Sensor
◆Thermal Time Constant: ca. 5 sec.(in stirred water)
◆Dielectric Strength Voltage: AC 2200V 1sec.
◆Insulation Resistance: DC 500V 100MΩ+
Zero Power Resistance R25 = 10.0kΩ±3% :
B value B25/50 = 3950K±2% :
Temperature range -20℃ - 80℃ :
⑲Resin Pipe Sensor
◆Thermal Time Constant: approx. 20 sec.
◆Dielectric Strength Voltage: AC 1800V 1 sec.
◆Insulation Resistance: DC 500V 100MΩ+
⑳Thermopile Module
Features: A temperature sensor that is inserted into a copper pipe and can
be used for a wide variety of purposes.
Features: A temperature sensor that has been dipped in epoxy resin and
optimized for measuring room temperature.
Features: A temperature sensor in a resin pipe that allows accurate
measurement of low temperatures.
Features: A module version of the infrared based
Thermopile non contact Sensor. Non Contact
◆Response : approx. 10ms
◆Angle : type55
◆Rated voltage : +5.5V
Measured Temperature: 0℃±3.0℃ :
Measuring temp. range: -35℃ - 35℃
Output Voltage : 0.547V - 3.453V
Air Conditioning
Zero Power Resistance R55 = 14.05kΩ±3% :
B value B25/50 = 4120K±2% :
Temperature range -20℃ - 80℃ :
Zero Power Resistance R25 = 10.0kΩ±1% :
B value B25/85 = 3435K±1% :
Temperature range -30℃ - 90℃ :
Unit: mm
Unit: mm
Unit: mm
Unit: mm
Thermistor Epoxy PVC Wire
(105°C heat resistant) Connector
Resin pipe Epoxy PVC Wire
(105°C heat
resistant)
Solder
Thermopile Connector Resin
Thermistor Epoxy Shrink Tube Shrink Tube
Thermistor
Connector Tube (105°C Tube (105°C
Home Appliances
※1
Screw Mount Sensor
Microwave Oven
◆Thermal Time Constant: approx. 80 sec.
◆Dielectric Strength Voltage: AC 1200V 1 sec.
◆Insulation Resistance: DC 500V 100MΩ+
Water Heater / Warm Water Toilet Seat
Flange Pipe Sensor
◆Thermal Time Constant: approx. 9 sec. (room temperature)
◆Dielectric Strength Voltage: AC 1200V 1 sec.
◆Insulation Resistance: DC 500V 100MΩ+
SUS 3 level Pipe Sensor
◆Thermal Time Constant: under 1 sec.
(in stirred water)
◆Dielectric Strength Voltage: AC 1200V 1 sec.
◆Insulation Resistance: DC 500V 100MΩ+
SUS Pipe Sensor
◆Thermal Time Constant: ca. 3.6 sec.(in stirred water)
◆Dielectric Strength Voltage: AC 1500V 1 sec.
◆Insulation Resistance: DC 500V 100MΩ+
10
2 2
2 1
2 3
2 4
Features: Easy to mount highly heat resistant temperature sensor with
integrated flange.
Features: A highly heat resistant screw mount type temperature sensor with a metal
terminal part.
Features: A temperature sensor optimized for water temperature measurement
with thin SUS Pipe terminal for high response speed.
Features: A temperature sensor optimized for water temperature measurement
that is inserted into an SUS Pipe.
※1: without connector
Zero Power Resist. R50 = 4.367kΩ±5% :
Temperature range - 30℃ - 180℃ (Sensing part) :
B value B0/100 = 3450K±3% :
Zero Power Resistance: R75 = 7.241kΩ±7% :
Temperature range : -20℃ - 200℃ :
B value B0/100 = 3970K±2% :
Zero Power Resistance: R50 = 17.60kΩ±3% :
Temperature range -20℃ - 120℃ :
B value B0/100 = 3970K±2% :
Zero Power Resistance: R40 = 26.06kΩ±3% :
Temperature range : -20℃ - 80℃ :
B value B0/100 = 3970K±2% :
Unit: mm
Unit: mm
Unit: mm
Unit: mm
Thermistor Epoxy
Polyimide
Ni-plated CP wire Silicon-Glass Mesh Tube
Brass mount
Leads
Connector
SUS316 L Pipe with Brass Ring
Presser Plate
Presser Plate
Polyimide
SUS 304 Pipe
Shrink Tube
Connector PVC Wire Crimp Contact
Flange Bend
PVC Wire (<105°C) Connector
Home Appliances
Home Appliances
Power Conditioner
◆Thermal Time Constant: approx. 80 sec.
◆Dielectric Strength Voltage: AC 2400V 1 sec.
◆Insulation Resistance: DC 500V 100MΩ+
火災報知機
11
Screw Mount Sensor
◆Thermal Time Constant: approx. 5 sec.(in stirred water)
◆Dielectric Strength Voltage: AC 1800V 1 sec.
◆Insulation Resistance: DC 500V 100MΩ+
Zero Power Resistance R55 = 14.05kΩ±1.5% :
B value B25/85 = 4120K±1% :
Temperature range -30℃ - 105℃ :
Dip Sensor (AR)
◆Thermal Time Constant: approx. 18 sec.
◆Dielectric Strength Voltage: AC 600V1 sec.
◆Insulation Resistance: DC 500V 100MΩ+
Dip Sensor
Rechargeable Battery
2 5
2 6
2 7
Features: Formed resin screw mount type temperature sensor with excellent insulation.
Features: Highly reliable temperature sensor that has been dipped in epoxy resin.
Features: Highly responsive temperature sensor that has been dipped in epoxy resin.
Shaped resin (UL94HB)
Contraction tube Lead wire Connector
Lead wire
Thermistor chip (AR)
Lead frame
Epoxy
Epoxy
Zero Power Resistance R25 = 20.0kΩ±1% :
B value B25/85 = 4013K±1% :
Temperature range -40℃ - 105℃ :
Zero Power Resistance R25 = 226.0kΩ±3% :
B value B25/85 = 4021K±1% :
Temperature range -40℃ - 100℃ :
Fire Alarm
Unit: mm
Unit:mm
Unit:mm
SUS Clip
Industrial Equipment
Liquid Temperature Measurement
◆Thermal Time Constant: approx. 20 sec. (in stirred water)
◆Dielectric Strength Voltage: AC1200V 1 sec.
◆Insulation Resistance: DC 500V 100MΩ+
Heat Sink
12
◆Thermal Time Constant: 0.6 sec. (Roller)
◆Dielectric Strength Voltage: AC 600V 1 sec.
◆Insulation Resistance: DC 500V 100MΩ+
Clip Sensor
◆Thermal Time Constant: approx. 60 sec.
◆Dielectric Strength Voltage: AC 600V 1 sec.
◆Insulation Resistance: DC 500V 100MΩ+
Screw Mount Sensor
Pipe Temperature Measurement
Screw Type Pipe Sensor 2 8
2 9
3 0
Features: Screw type temperature sensor that can be used in water / oil tanks.
Features: A temperature sensor that can be directly mounted to pipes and
can be easily exchanged for maintenance.
Features: A temperature sensor that can easily be mounted
with М3 / М5 screws.
Tube
SUS Pipe
Lead Wire
Thermistor
Terminal
M5 metal terminal □0.5 tin plated 42 alloy
Zero Power Resistance R25 = 10.0kΩ±1% :
B value B25/85 = 3435K±1% :
Temperature range -10℃ - 105℃ :
Zero Power Resistance R85 = 1.075kΩ±3% :
B value B25/85 = 3969K±1% :
Temperature range -20℃ - 120℃ :
Zero Power Resistance R25 = 10.0kΩ±0.5% :
B value B25/85 = 3976K±0.5% : Temperature range -50℃ - 150℃ :
M3 metal terminal
Unit: mm
Unit: mm
Unit: mm
□0.5 tin plated 42 alloy
L1
L2
Flange Pipe Sensor
Industrial Equipment
Cooking Appliances
◆Thermal Time Constant: approx. 120 sec.
◆Dielectric Strength Voltage: AC 1200V 1 sec.
◆Insulation Resistance: DC 500V 100MΩ+
◆Thermal Time Constant: ca. 78 sec.
◆Dielectric Strength Voltage: AC 1200V 1 sec.
◆Insulation Resistance: DC 500V 100MΩ+
◆Thermal Time Constant: approx. 5.5 sec.
◆Dielectric Strength Voltage: AC 600V 1 sec.
◆Insulation Resistance: DC 500V 100MΩ+
Heater Temperature Measurement
13
Screw Mount Sensor
M5 Screw Type Sensor
3 1
3 3
3 2
Features: Easy to mount temperature sensor with integrated flange.
Features: Highly heat resistant Screw Mount type temperature sensor with
metal terminal.
Features: Screw Mount type temperature sensor that can be mounted
directly to the heater block.
※1:Without connector
※1:Tip M5 screw part only
SUS Pipe Lead Wire
Brass bracket
Glass braided tube Lead Wire
Connector
Zero Power Resistance R25 = 5.1kΩ±5% :
B value B25/85 = 3200K±2% :
Temperature range -10℃ - 120℃ :
Zero Power Resistance R100 = 3.3kΩ±2.5% :
B value B0/100 = 3970K±2% :
Temperature range -20℃ - 180℃ : ※1
Zero Power Resistance R135 = 3.138kΩ±3% :
B value B25/85 = 3750K±3% :
Temperature range -50℃ - 250℃ :
※1
Unit: mm
Unit: mm
Unit: mm
L1
L2
Brass Pipe with M5 Screw Fluorine Rubber Wire Connector
Ⓓ
Ⓒ
Type R25 B25/85 Resin color Temp. range ℃
EC2F102A2-71014 1kΩ ±1% 3100K±1% Light blue
EC2F202A2-71048 2kΩ ±1% 3182K±1% Red
EC2F502A2-40103 5kΩ ±1% 3324K±1% Gray
EC2F103A2-40113 10kΩ ±1% 3435K±1% Black
EC2F203A2-70030 20kΩ ±1% 4013K±1% Blue
EC2F503A2-70456 50kΩ ±1% 4060K±1% White
EC2F104A2-60109 100kΩ ±1% 4665K±1% Green
-40~+110
-40~+90
14
Standard Assembly Products
Ⓐ xxxAT-11
◆Dielectric Strength Voltage: AC1200V 1 sec.
◆Insulation Resistance: DC500V 100MΩ+
103AT-2-34119
EC2F103A2-40113-600AY
103JT-025-600AY
Ⓑ
EC2F103A2-xxxxx
◆Dielectric Strength Voltage: AC600V 1 sec.
◆Insulation Resistance: DC500V 100MΩ+
Dissipationfactor
Max. powerdissipation
Temp. range
mW/℃ mW at 25℃ ℃
10.0kΩ ±1% 3435K±1% approx. 3.0 approx. 80 15 -10~+105
R25 B25/85Thermal time
constant s※1
Dissipationfactor
Max. powerdissipation
Temp. range
mW/℃ mW at 25℃ ℃
102AT-11 1.00kΩ ±1% 3100K±1%
202AT-11 2.00kΩ ±1% 3182K±1%
502AT-11 5.00kΩ ±1% 3324K±1%
103AT-11 10.0kΩ ±1% 3435K±1%
203AT-11 20.0kΩ ±1% 4013K±1%
approx. 2.6 約75 13
−50~+90
−50~+105
Type R25 B25/85
Thermal time
constant s※1
Dissipationfactor
Max. powerdissipation
Temp. range ※3
mW/℃ mW at 25℃ ℃
10.0kΩ ±1% 3435K±1% approx. 3.0 approx. 80 15 -30~+105
R25 B25/85
Thermal time
constant s※1
◆Dielectric Strength Voltage: AC2400V 1 sec.
◆Insulation Resistance: DC500V 100MΩ+
◆Dissipation factor: approx. 3.0mW/℃ ◆Dielectric strength voltage: AC2400V 1 sec.
◆Thermal time constant: approx. 80 sec. ◆Insulation Resistance: DC500V 100MΩ+
Dissipationfactor
Max. powerdissipation
Temp. range ※3
mW/℃ mW at 25℃ ℃10.0kΩ ±1% 3435K±1% approx. 0.7 approx. 5 3.5 -30~+105
R25 B25/85
Thermal timeconstant
s※1
◆Dielectric Strength Voltage: AC120V 1 sec.
◆Insulation Resistance: DC100V 100MΩ+
Unit: mm
Unit: mm
Unit: mm
Unit: mm
Unit: mm
※1: measured in still air ※2: measured in stirred water ※3: without connector
Ⓔ
0.3 SQ TPE Resin Wire Solder
Type Mark Brand
Terminal
Tin Plating
Resin Form(UL94HB)
Shrink Tube PVC
Lead-free Solder Lead-free Solder
Shrink Tube PVC Resin Form(UL94HB) Lead-free Solder
Connecting Terminal (Copper-
Alloy), Solder (Inside)
Dissipation
Factor
Max.
Power
Dissipation
□0.5 tin plated 42 alloy
Standard Assembly Products Ⓕ EF1M493G2-ASSY-1
EP1C212C0-ASSY-3
ED5F103A2-ASSY-4
Ⓖ
Ⓗ
Ⓘ 104AT-4-ASSY-5
※1: measured in still air ※2: measured in stirred water ※3: without connector 15
No L Connector
1 185±5 XAP-02V(blue)
2 290±10 XAP-02V(white)
Dissipationfactor
Max. powerdissipation
Temp. range
mW/℃ mW at 25℃ ℃10.0kΩ ±1% 3435K±1% approx. 4.0 approx. 2 20 -30~+80
B25/85
Thermal time
constant s※2R25
Unit: mm
◆Dielectric Strength Voltage: AC1200V 1 sec.
◆Insulation Resistance: DC500V 100MΩ+
◆Dielectric Strength Voltage: AC1800V 1 sec.
◆Insulation Resistance: DC500V 100MΩ+
◆Dielectric Strength Voltage: AC1500V 1 sec.
◆Insulation Resistance: DC500V 100MΩ+
Dissipationfactor
Max. powerdissipation
Temp. range ※3
mW/℃ mW at 25℃ ℃3.3kΩ ±2.5% 3970K±2% 約2.2 約78 11 -20~+180
R100 B0/100
Thermal time
constant s※1
Dissipationfactor
Max. powerdissipation
Temp. range ※3
mW/℃ mW at 25℃ ℃1.433kΩ ±2% 3400K±2% approx. 5.0 approx. 10 25 -30~+80
R35 B0/25
Thermal time
constant s※2
◆Dielectric Strength Voltage: AC600V 1 sec.
◆Insulation Resistance: DC500V 100MΩ+
Dissipationfactor
Max. powerdissipation
Temp. range
mW/℃ mW at 25℃ ℃100.0kΩ ±1% 4261K±1% approx. 4.0 approx. 35 20 -40~+90
R25 B25/85
Thermal time
constant s※1
Unit: mm
Unit: mm
Unit: mm
EF1M493G2-ASSY-2
Thermistor
Epoxy
Brass Bracket
PVC Tube (<105°C)
Silicon Glass Mesh Tube
Fluorine Wire
Connector
Heat Resistant
PVC Wire (Red)
Epoxy
Deoxidized Phosphor
Copper Pipe
Heat Resistant PVC (0.14sq, black)
Solder
Chip Silicone Varnish
Inside
Epoxy Leads
Chip Solder
Inside
approx. approx.
2015.1.05
Thank you for considering Semitec. Please observe the following precautions when using
our products:
1) Buyer shall always consult Semitec Sales when considering Semitec products for applications not listed herein or for high reliability applications listed below
that could potentially harm human life or property. Buyer shall also consider implementing fail-safe mechanisms at all times.
○Medical Equipment ○Transportation Equipment (Automotive, Railroad, Shipping, etc.) ○Aerospace Equipment ○Traffic Equipment ○Security
Equipment (Crime and Disaster Prevention) ○ Nuclear-related Equipment ○Military Equipment ○Undersea Equipment ○Safety Device ○Other
equipment also requiring equally high reliability
2) Buyer shall not use products outside the defined specification limits or storage conditions, as reliability may be compromised.
3) Buyer shall take precautions against any improper use of products that could result in heat generation, ignition, explosion, scattering, etc.
4) Some products may have sharp protrusions or edges due to their structure. Workers must, therefore, be adequately trained in handling products to prevent
any
related accidents.
5) Processing products may be accompanied by destruction, scattering, etc. of parts. Workers must, therefore, be adequately trained and be well versed in
product
material and various work conditions, to prevent any related accidents.
6) When handling products, Buyer shall take precautions not to apply tension, pressure or heat that exceeds the recommended specifications, as such stress
may cause
open or short circuits, or insulation failures that accelerate deterioration or impair intended performance of the products.
7) Buyer shall always consult Semitec Sales on any uncertainties regarding application, product usage or items not mentioned herein, to avoid improper use of
products.
8) Buyer shall take necessary measures to prevent any damages due to accidents resulting from product failure or malfunction.
9) Semitec assumes no liability or responsibility for any accidents resulting from Buyer’s failure to follow the product usage guidelines mentioned above.
10) Buyer shall always consult Semitec Sales when considering an application outside of a product’s intended use. A separate, individual agreements can be
concluded if necessary, upon confirming application reliability.
Caution
■Head Office : 7-7,Kinshi 1-chome,Sumida-ku,Tokyo 130-8512,Japan
Overseas Sales Section : TEL :+81-3-3621-2704 E-mail: [email protected]
■USA : SEMITEC USA CORP. :TEL:+1-310-540-2330 FAX:+1-310-540-2331 E-mail: [email protected]
■HONG KONG : SEMITEC (H.K.) CO.,LTD. : TEL:+852-2369-6773 FAX:+852-2739-2396 E-mail: [email protected]
■TAIWAN : SEMITEC TAIWAN CORP. : TEL:+886-2-2593-6622 FAX:+886-2-2593-0089 E-mail: [email protected]
■KOREA : SEMITEC KOREA CO.,LTD. : TEL:+82-2-3281-1155 FAX:+82-2-3281-3338 E-mail: [email protected]
■SHANGHAI : SEMITEC SHANGHAI OFFICE : TEL:+86-21-5308-6000 FAX:+86-21-5830-5008 E-mail: [email protected]