Cummins 2019+ Quick Startcontent.efilive.com/documents/Cummins 2019+ Quick Start.pdf ·...

Cindy Myers

Cummins 2019+ Quick Start Guide

EFILive, EFILive FlashScan and EFILive AutoCal are registered trademarks of EFILive Limited.

All other trademarks belong to their respective owners.

Cummins 2019+

Quick Start Guide

© 2014 EFILive Limited

All rights reserved

First published 14 August 2019

Revised 21 August 2019

http://www.efilive.com/

Cummins 2019+ Quick Start

[email protected] - 1 - www.efilive.com

Contents

............................................................................................................ 3

Prerequisites .................................................................................................................... 3

Intended Audience ....................................................................................................... 3

Computer Knowledge ................................................................................................... 3

...................................................................................................... 4

Introduction ...................................................................................................................... 4

CM2450B ECM Overview ............................................................................................ 4

RSA Digital Signature .................................................................................................. 4

Security Gateway Module ............................................................................................ 4

Software ....................................................................................................................... 5

Overview .................................................................................................................. 5

Requirements ........................................................................................................... 5

Additional Support Resources ...................................................................................... 5

CSP5 Cummins Switchable Programming .................................................................... 6

Logging Data ................................................................................................................ 6

FlashScan/AutoCal Capacity and Tune File Sizes ....................................................... 6

Supporting Remote Customers .................................................................................... 6

Failed Flash Recovery Methods ................................................................................... 6

............................................................................................................ 7

2019 Quick Start .............................................................................................................. 7

Finding the Correct Base File ....................................................................................... 7

Determine Current Calibration .................................................................................. 7

Match Calibration Requirements .............................................................................. 9

Editing a Tune File ..................................................................................................... 10



Licensing Requirements ............................................................................................. 12

Dodge Cummins Tuning Option Enabled ............................................................... 12

VIN Licensing ......................................................................................................... 13

Flashing the ECM ....................................................................................................... 13

EFILive Scan and Tune .......................................................................................... 13

FlashScan V2 ......................................................................................................... 15

AutoCal ................................................................................................................... 16

.......................................................................................................... 17

BBX Configuration ......................................................................................................... 17

Setting up FlashScan V2/AutoCal for Reading, Flashing and Logging using V8 Scan and Tune ........................................................................................................... 17

BBL (Black Box Logging) Configuration ................................................................. 17

BBR & BBF (Black Box Reading and Flashing) Configuration ............................... 18

Quick Setup ............................................................................................................ 18

Move Tune and Log files from FlashScan V2/AutoCal to your PC ............................. 19



Prerequisites

Intended Audience

EFILive Customers using the V8 Scan and Tune Tool software.

Computer Knowledge

It is expected that readers have a basic understanding of:

The Windows operating system;

Starting and using Windows applications;

Navigating folders using Windows Explorer.



Introduction

This document is intended to assist EFILive customers with the basic operations and steps necessary to work with 2019+ 6.7L Cummins supported vehicles.

CM2450B ECM Overview

Due to the CM2450B ECM's restrictive architecture, this ECM cannot be read via the OBD-II Port.

Customers will need to obtain a suitable base file for editing and flashing. A selection of EFILive compatible base stock files are readily available on the internet or custom files may be purchased through organizations that have the necessary hardware and software to create personalized base files.

Because you cannot read the existing tune in the ECM it is important you select the correct base tune to suit your vehicle.

RSA Digital Signature

The EFILive ECM flash process manages the removal of the Digital Signature via OBD-II flashing in the following circumstances:

Controller Flash Method

CM2450B (CMF) In vehicle and bench harness flashing.

CM2350B (CME) In vehicle and bench harness flashing.

NOTE: The ECM must be fully operational and not in boot mode as a result of a failed flash (error $0340) or forced boot mode. Where the ECM is in boot mode, the unlock process is bypassed and two-step flash process is required to remove the digital signature.

1. Recover the ECM by flashing a stock tune to restore the ECM to operational mode.

2. Flash the ECM to remove the digital signature.

Security Gateway Module

In 2018 Dodge implemented an additional anti-tuning security measure via the security gateway module. Customers will need to bypass this module by installing a Security Gateway Module bypass cable (SGM bypass cable).

The SGM bypass cable requires users to replace the two CAN wires in the factory OBD-II port and connect the bypass cable into the large white connector just above the OBD-II port in any of the available slots. This cable remains permanently in the truck and does not need to be removed after flashing.

The OBD-II port will retain all normal functionality, and only bypasses the SGM to allow flashing to the ECM.



Where the SGM module is detected and a bypass cable is not in place, the following error will be displayed when the flash is aborted.

Aborting Flash: SGM Detected Please: Wait... Script exited with code $0333: Security Access Denied ($33).

Software

Overview

EFILive presently has two major software versions (V7 and V8) that implement different parts of the tuning and scanning process. The V8 software is undergoing significant development and will eventually supersede V7 entirely for FlashScan V2 customers.

Cummins customers must install both versions, the following table displays Cummins 2019+ software functionality.

Feature V7 V8

Scanning

OBDII Diagnostics

Reading

Flashing

Tune Editing

VIN License Management

Firmware Management

Requirements

The most recent Cummins software enhancements are available in the following product versions:

EFILive V8.2.25 or later.

FlashScan V2 / AutoCal Firmware - V2.07.140 or later.

The latest software is available for download from the EFILive website here: https://www.efilive.com/download-efilive

Additional Support Resources

If, after reviewing this guide, further assistance is required please contact the EFILive Authorised Reseller from whom you purchased your product. They are your first point of contact for EFILive support related inquiries.

If your question is in relation to the actual tuning of your vehicle (i.e. how to gain performance, economy etc.) then please ask these questions on the EFILive Forum (http://forum.efilive.com/). EFILive does not provide support or assistance for the actual tuning of any supported vehicles.

http://forum.efilive.com/



CSP5 Cummins Switchable Programming

EFILive's CSP custom operating system is not currently available for Cummins 2019+ vehicles and will be developed at a later date.

Logging Data

Generic scan tool data for the CM2450B has been implemented. EDA logging for Cummins 2019+ vehicles and will be developed at a later date.

FlashScan/AutoCal Capacity and Tune File Sizes

FlashScan V2 has approx. 6MB of internal memory capacity for the storage of tune and log files. Capacity can be extended using an SD card.

AutoCal has approx. 6MB of internal memory capacity for the storage of tune and log files.

Controller Tune File Size

CM2450B (CMF) Approx. 3.5MB each

CM2350B (CME) Approx. 3.5MB each

CM2200 (CMD) Approx. 2.5MB each

Supporting Remote Customers

Due to the size of tune files, moving tunes on/off an AutoCal device will be prevalent. EFILive recommends to those tuners using AutoCal for their end users, that tune files are managed via the Quick Setup in order to manage device configurations and minimize support issues.

Failed Flash Recovery Methods

In the event that an ECM fails during the flashing process, recovery methods exist to restore the ECM.

In most instances, simply retrying the flash process will return the ECM to working order.

In the instance where tuners apply security restrictions to a tune file, including locking to the controller serial number, and the flash fails, you must try to recover the ECM with a file that has no security restrictions in place (e.g. stock tune) before attempting to reflash a file with security restrictions.

If retrying the flash process does not return the ECM to working order, the Problem Flashing a Controller and Controller Recovery knowledgebase articles provide additional support resources.

https://support.efilive.com/kb_article.php?ref=8254-QOGC-9586

https://support.efilive.com/kb_article.php?ref=8254-QOGC-9586

https://support.efilive.com/kb_article.php?ref=7233-PHJN-8346&auth=b1f988355a56c13720213b2c8160f876



2019 Quick Start

Finding the Correct Base File

The following instructions will determine the base tune file that should be used for each vehicle.

EFILive does not provide stock tunes or modified tunes. There are a variety of stock tunes available on the internet, or custom stock tunes can be purchased through organizations that have the necessary hardware and software to create personalized base files.

Determine Current Calibration

There are 3 methods to find the calibration details of the tune presently in the ECM. Customers can choose which method best suits their needs.

V8 Scan and Tune

1. With FlashScan V2 or AutoCal connected to your vehicle and your PC, open EFILive V8 Scan and Tune and select [F4: OBD] -> [F2: OBD].

2. On the Details tab use the Auto Detect button, or right click on the Right-click to select engine-controller box and manually select the ECM.

3. Select the Retrieve All Information button to populate controller data. 4. Copy or record the Calibration ID to use in the match calibration requirements

step.



FlashScan V2 and AutoCal Display

These instructions assume FlashScan and AutoCal have been previously configured for BBX. Refer to BBX Configuration section of this document for configuration requirements.

FlashScan V2

1. With FlashScan V2 connected to your vehicle, select [F1: Scan Tool] -> [F1: Select PIDs] and select controller you wish to display.

2. Return to the main menu and select [F3: Diagnostics] -> [F1: Display Info] -> [F1: Display VIN/Info], the following data will be displayed:

3. Record the details displayed in the Cal: field to use in the match calibration requirements step.

4. If the [Select PIDs] option is not selected first, the following will be displayed:

AutoCal

For AutoCal, the user must boot into the advanced menu by holding down the [Next] button while powering up the device.

1. Navigate to [Scan Tool] -> [Select PIDs] and select the controller you wish to display.

2. Users can navigate to a range of options using the [Next] button. The following options are available:

"Scan Tool"->"Display VIN" "Scan Tool"->"Display OS" "Scan Tool"->"Display SN" "Scan Tool"->"Display Cal ID"

Where the display information exceeds 8 characters, a ">" character is displayed at the end of the data prompting the user to press [Next] to scroll the data horizontally. The "<" character indicates that the user can press the [Prev] key to scroll the data back again.

3. Record the details displayed in the Cal ID: field to use in the match calibration requirements step.



4. If the [Select PIDs] option is not selected first, the following will be displayed:

--------

VIN

3D7KS26>

--------

SN:

Sel PIDs

--------

OS:

Sel PIDs

--------

Cal:

Sel PIDs

--------

Record All Diagnostics

FlashScan V2 and AutoCal have the ability to create a text file that can be viewed using Windows notepad.

FlashScan V2

1. With FlashScan V2 connected to your vehicle, select [F1: Scan Tool] -> [F1: Select PIDs] and select controller you wish to display.

2. Return to the main menu, then select [F3: Diagnostics] -> [F4: Record All Diags]. FlashScan will display the file name that is saved onto the device.

AutoCal

1. Navigate to the [Select PIDs] menu to confirm controller selection. 2. Navigate to the [Record Diags] menu to save the text file. AutoCal will

display the file name that is saved to the device.

NOTE: If [Select PIDs] is not performed before [Record Diags] a text file will be saved, but it will NOT contain any data.

Once the file is saved, users should connect their FlashScan or AutoCal device to their PC, Open EFILive Explorer and navigate to the scan directory. The relevant file can then be transferred to PC and then opened or emailed to their tuner.

Match Calibration Requirements

1. Using the Calibration ID identified in the above steps, search the Cummins Flash Availability Document, found here for a matching entry.

2. Copy the Calibration ID without the 2 letter suffix from the New Part Number(s) column.

3. To find a matching tune file, open the chosen CMF.ctz file in to EFILive V8 Scan and Tune and match the Calibration ID displayed under the [F3: Tune] -> [F3: Calibration] tab against the Calibration ID chosen from the Cummins Flash Availability document.

The two letter suffix in the Calibration ID indicates the tune revision identifier, not a variation in Operating system.

Some Calibrations may be listed in the Cummins Flash Availability document multiple times. If you cannot find a matching base file, check the document for additional records of your Calibration ID.

https://forum.efilive.com/showthread.php?28187-2010-Cummins-stock-tune-library



4. Once you find a matching tune this can now become your base file should you ever need to revert back to a stock tune.

You cannot save the tune already installed in the ECM, once you flash over it, it is gone forever, so choose your base tune wisely.

Editing a Tune File

Follow the steps below to modify your Dodge Cummins ECM calibration.

1. Open the EFILive V7.5 Tune Tool application. 2. Click the File Open button.

3. Navigate to the location on your computer where the saved tune file you wish to open is located. Then click on the tune file to select it, and click Open.

4. Navigate to the table(s) you wish to modify by using the Windows Explorer style navigation window.

5. Edit selected table(s) by changing the values or by using the adjustment functions.



6. A range of tune file security options can be applied in the Permissions tab (or via the V8 software using [F3: Tune] -> [F4: Properties] -> Security Restrictions tab).

7. Save changes to the tune file by using the Save tuning file, Save tuning file as, or Save tuning file for AutoCal option.

If using the Save option, ensure you have a copy of your stock tune saved elsewhere.

Save tuning file as, and Save tuning file for AutoCal options automatically appends a sequence number to the filename to make it unique giving users a history of sequentially numbered files with each saved change made.



Licensing Requirements

To Flash a Dodge Cummins ECM, the following licensing conditions must be met:

1. For FlashScan V2, the Dodge Cummins Tuning Option must be enabled. 2. FlashScan V2/AutoCal must have an available VIN License (if not already

licensed).

Dodge Cummins Tuning Option Enabled

To ensure that your FlashScan V2 device is licensed to tune Dodge Cummins vehicles:

1. Connect your FlashScan V2 or AutoCal device to your PC. 2. Open the EFILive Scan and Tune application. 3. Select the [F7: License] option in the left-hand pane. 4. Select [F2: Hardware] to display Tuning License details.

5. To purchase additional Tuning Licenses for FlashScan V2, click on the Purchase Tuning License Activation Code(s) link to order products. NOTE: AutoCal Users should contact their tuner before purchasing Tuning Licenses.

6. Enter emailed Activation Code and select Activate.



VIN Licensing

Each vehicle that you tune requires an available VIN license. The license is allocated during the flashing process. Reflashing the same controller multiple times using the same FlashScan V2/AutoCal only uses one license.

To check that you have an available VIN license to allocate to your vehicle perform these steps.

1. Connect your FlashScan V2 or AutoCal device to your PC. 2. Open the EFILive Scan and Tune application. 3. Select the [F7: License] option in the left-hand pane. 4. Select [F3: VINs] to display VIN License details.

5. To purchase additional VIN Licenses, click on the Purchase Activation Code(s) link to order products. NOTE: AutoCal Users should contact their Tuner before purchasing additional VIN licenses to discuss tune file compatibility.

6. Enter emailed Activation Code and select Activate.

Flashing the ECM

Dodge Cummins ECM flashing is supported by;

1. EFILive Scan and Tune software (V8 software). 2. FlashScan V2. 3. AutoCal.

EFILive Scan and Tune

Follow the steps below to flash your Dodge Cummins ECM controller.

1. Connect your FlashScan V2 or AutoCal device to your PC and your vehicle. 2. Turn the vehicle ignition to the On positon (not the Accessory

position. Vehicle must not be cranked/running when flashing). 3. Open the EFILive Scan and Tune application.



4. Select the [F3: Tune] option in the left-hand pane. 5. Click on the Open button at the bottom left of the screen. 6. Select the calibration file for the controller you wish to flash or license. 7. If tune file security has been applied to the tune file, review and accept the

Security Warning.

7. Click on the [F7: Full Flash] options in the left-hand pane.

8. Click on the Check License button. This will indicate if the controller is already licensed or not.

9. When the Check License process is complete a countdown timer will be shown. When prompted perform the following actions:

a. Turn the vehicle ignition Off. b. Click on the Start button to begin the countdown timer. c. DO NOT turn the vehicle ignition on until the countdown timer

expires. This time is critical to allow the ECM to perform internal functions after a read/flash operation.



10. If the controller is not licensed, select the Activate License button, and follow the prompts to license the controller.

11. Select Full Flash button to commence the flash. Three notification screens will display. Please ensure that you read and understand the contents of these screens before proceeding with the flash operation.

12. While the ECM is flashing an Elapsed time indicator, an Estimated Time Remaining indicator, and a Progress bar will display detailing the Flash progress.

13. When the flash process is complete a countdown timer will be shown. When prompted perform the following actions:



14. Once the countdown timer is completed the flash summary will be shown.

FlashScan V2

Follow these steps to license and flash the selected controller.

1. Setup FlashScan V2 for BBX features if not already setup. 2. Copy selected tune file(s) from your PC to FlashScan V2 if not already copied. 3. Connect your FlashScan V2 device to your vehicle. 4. Turn the vehicle ignition to the On positon (not the Accessory position. Vehicle

must not be cranked/running when flashing). 5. Navigate to the F2 Tune Tool -> F1 Tuning and select F3 Program Full menu

option. 6. Using the arrow keys, navigate to the correct tune file and select OK. 7. If the controller has not been licensed by the selected FlashScan V2 previously,

you will be presented with the message License this controller now? Select Yes to license the controller.

8. Click the OK button to initiate the flash operation.



9. When the flash process is complete the Reset Controller notification will be shown. When prompted perform the following actions:



AutoCal

Follow these steps to license and flash the selected controller.

1. Install AutoCal configuration files provided by your Tuner if not already setup. 2. Copy selected tune file(s) from your PC to FlashScan V2 if not already copied. 3. Connect your AutoCal device to your vehicle. 4. Turn the vehicle ignition to the On or Accessory position (vehicle must not be

cranked/running when flashing). 5. Navigate using the arrow keys to the Full 1-5 options for full flash. 6. Select the correct tune file from those listed and select OK. 7. If the controller has not been licensed by the selected AutoCal device, you will be

presented with the message License controller? Select OK to license the controller.

8. Click the OK button to initiate the flash operation. 9. When the flash process is complete the Reset Controller notification will be

shown. When prompted perform the following actions: a. Turn the vehicle ignition Off. b. Click on the Start button to begin the countdown timer. c. DO NOT turn the vehicle ignition on until the countdown timer




BBX Configuration

Setting up FlashScan V2/AutoCal for Reading, Flashing and Logging using V8 Scan and Tune

There are a range of configuration files that need to be programmed onto FlashScan and AutoCal to enable hardware to work in standalone mode for your controller. Each step can be programmed into the device individually, or collectively.

With your FlashScan V2/AutoCal plugged in to a USB port, open V8 Scan and Tune and click on the [F5: BBX] option.

BBL (Black Box Logging) Configuration

EDA logging for Cummins 2019+ vehicles and will be developed at a later date. To configure FlashScan/AutoCal for generic logging, to determine the Calibration ID and generate the Record Diags file please:

1. Select the [F2: Scan] option in the left-hand pane. 2. Remove any unnecessary controller configurations to ensure capacity restrictions

are not exceeded. 3. Add the correct controller to your list;

a. Press the green '+' icon. b. Right clock on the Engine Controller box. c. Select controller. d. Read and accept the BBL Information display. e. Select OK.



BBR & BBF (Black Box Reading and Flashing) Configuration

1. Select the [F3: Tune] option in the left-hand pane. 2. Remove any unnecessary controller configurations to ensure capacity restrictions

are not exceeded. 3. Add your chosen controller(s) to your list;

a. Press the green '+' icon. b. Right click on the Engine Controller or Transmission Controller box. c. Click on a selected controller. d. Select OK

Quick Setup

1. Select the [F6: Quick Setup] option in the left-hand pane.



2. Edit FlashScan V2 or AutoCal Settings as required. Ensure that CSP5 tunes can be switched after powering off FlashScan V2/AutoCal by selecting [F6: Logging] –> At start-up, automatically re-select the most recently used PID list.

3. Select appropriate BBX Quick Setup options. 4. To place tune files on FlashScan V2/AutoCal, add tune files to the Quick Setup

using the green '+' icon.

Write this configuration to FlashScan V2 or AutoCal using the [Program Quick Setup] function. The [Program Quick Setup] programs all selected Scan, Tune, Switch options, as well as selected device settings, BBX Quick Setup selections and tune files. Once the device is programmed, FlashScan V2 or AutoCal is configured for BBX functions and tune switching via FlashScan V2 or AutoCal.

Each option can be programmed individually using the [Program] button on each tab, or collectively using the [Program Quick Setup] option.

Move Tune and Log files from FlashScan V2/AutoCal to your PC To move tune files and log files from FlashScan V2/AutoCal to your PC;

1. Connect your FlashScan V2/AutoCal device to your PC. 2. Open EFILive Explorer. 3. Navigate to the directory on your PC where you wish to save the file. 4. Navigate to: [F3: Data Files]. 5. Select appropriate folder on your FlashScan V2/AutoCal device and drag the

selected file to your PC.



Once tune and log files are copied from your FlashScan/AutoCal to your PC, they can be opened/viewed using EFILive Scan and Tune, V7 Tune Tool, or V7 Scan Tool.

Cummins 2019+ Quick Startcontent.efilive.com/documents/Cummins 2019+ Quick Start.pdf ·...

Documents

Transcript of Cummins 2019+ Quick Startcontent.efilive.com/documents/Cummins 2019+ Quick Start.pdf ·...