CT900 TV BRACKET - Spirit Fitness · 2018. 11. 5. · CT900 TV BRACKET STEP FIVE HARDWARE FOR STEP...

CT900 TV BRACKET INSTALLATION GUIDE

Spirit Fitness

www.spiritfitness.com

Congratulations on your new TV bracket and welcome to the Spirit Fitness family!

Thank you for your purchase of this TV bracket from Spirit Fitness. This bracket was manufactured by one of the leading fitness manufacturers in the world and is backed by one of the most comprehensive warranties available. Through your dealer, Spirit Fitness will do all we can to make your ownership experience as pleasant as possible for many years to come. If not purchased direct from Spirit Fitness, the local dealership where you purchased this bracket is your administrator for all Spirit Fitness warranty and service needs. Their responsibility is to provide you with the technical knowledge and service personnel to make your experience more informed and any difficulties easier to remedy.

Please take a moment at this time to record the name of the dealer, their telephone number, and the date of purchase below to make any future, needed contact easy. We appreciate your support and we will always remember that you are the reason that we are in business. Please complete and mail your registration card today.

Yours in Health,

Spirit Fitness

NAME OF DEALER _____________________________________

DEALER PHONE # _____________________________________

PURCHASE DATE _____________________________________

Spirit Fitness

WARNING: This product may contain a chemical known to the state of California to cause cancer, birth defects, or other reproductive harm.

5


CT900 TV BRACKET STEP ONE1. To route the TV cable, first remove the

TV bracket cover behind the console, and the outer right side hand rail cover, and the lower right side console mast cover.

6Spirit Fitness

CT900 TV BRACKET STEP TWO1. Using the TV cable wire, or a wire snake, route

the cables (indicated by thick black line) from the rear opening under the console toward the right side (left when facing the rear of the machine) and out of the console covers near the top of the right console mast.

2. Run the cables through the large hole in the top of the console mast until it exits the bottom of the console mast.

7


1. Raise the incline of the machine to 15 percent to make this next step easier. Route the cables from the bottom of the console mast along the bottom of the treadmill frame to the pivot point of the incline frame.

2. Run the cables down the incline frame towards the transportation wheel and then along the bottom horizontal rail of the frame and tie it off at about the center of the rail. Add tie wraps to secure the cables along the incline frame and under-carriage of the treadmill.

CT900 TV BRACKET STEP THREE

8Spirit Fitness

CT900 TV BRACKET STEP FOUR

1. Attach the TV bracket cover back onto the back of the console after removing the TV bracket dummy plate on the cover.

2. Run the cables through the TV bracket and mount the bracket to the back of the console with the four M8 BOLTS (4) and SPLIT WASHERS (5).

HARDWARE FOR STEP 4

PART TYPE DESCRIPTION QTY

4 BOLT M8x20mm 4

5 SPLIT WASHER M8 4

9


CT900 TV BRACKET STEP FIVEHARDWARE FOR STEP 5

PART TYPE DESCRIPTION QTY

6 SCREW M4x12mm 4

7 SPLIT WASHER M4 4

8 FLAT WASHER 4x1.0 4

9 SCREW M5x12mm 1

1. Attach the TV to the bracket with the four M4 SCREWS (6), SPLIT WASHERS (7) and FLAT WASHERS (8).

2. Mount the plastic cover over the TV mounting plate with the M5 SCREW (9) and attach the cables to the TV.

3. Re-install the handrail cover and lower console mast cover.

10Spirit Fitness

NOTES

11


NOTES

CT900 TV BRACKET - Spirit Fitness · 2018. 11. 5. · CT900 TV BRACKET STEP FIVE HARDWARE FOR STEP...

Documents

Transcript of CT900 TV BRACKET - Spirit Fitness · 2018. 11. 5. · CT900 TV BRACKET STEP FIVE HARDWARE FOR STEP...