c:scape Beam - Amazon S3...c:scape Beam Page 1 of 14 939500366 Rev D 1/8", 3/16" HEX DRIVE 3/8" If...

c:scape™ Beam

of 14939500366 Rev D

1/8", 3/16"HEX DRIVE

3/8"If you have a problem, question, or request, callyour local dealer, or Steelcase Line 1 at888.STEELCASE (888.783.3522)for immediate action by people who want to help you.

(Outside the U.S.A., Canada, Mexico, Puerto Rico, and the U.S. Virgin Islands, call: 1.616.247.2500)Or visit our website: www.steelcase.com

© 2009 Steelcase Inc. Grand Rapids, MI 49501 U.S.A.

Printed in U.S.A.

POWER

4

BEAM

1

DESKING

3

MID STORAGE

2

LOW STORAGE

5

PRIVACY

6

Furniture should be installed in sequence shown below.

THIS INSTALLATION SEQUENCE IS HERE.

3/8", 1/2"SOCKET

1

2

of 14939500366 Rev D

NOTE: For multiple beam assemblies,assess the levelness of the floor,setting the first beam nearest the highspot in the floor with the glides fully retracted. Beam glides can accommodate 2" of adjustment for uneven floors.

Remove the covers from thebeam framework and store ontheir long sides for protection

1. Pull outward at each cover cliplocation to release the top edge of thecover (clips are located at the ends andevery 24").

2. Rotate the cover away from thebeam and lift upward to releasethe bottom edge of the cover.

NOTE: Use caution to preventscratching the face of the cover.

UNACCEPTABLE ALUMINUMCOLOR MATCH

NOTE: For multiple in-line beamassemblies, stage the beam orientationprior to installation to determine thebest color/appearance match. Becauseof the directional extrusion process,the anodized finish appearance changesdepending on the viewing angle.

24"

FLOOR LINE

OR

3

3

of 14939500366 Rev D

Level the first beam using the beamglides so that the top of the beamis 24" above the floor

3. Adjust the glide by rotating the body ofthe glide by hand or with a 3/8" hex drive tool onthe top end of the glide.

NOTE: Straight runs mustbe temporarily supportedor have feet installed for stability.

LOWER FOOTBRACKET(NOTCHED)

UPPER FOOTBRACKET

4a

1/4-20 x 2"CAP SCREW

4b

of 14939500366 Rev D

TAPPED HOLE

CLEARANCE HOLEAttach the support feet for stabilityand adjust the feet glides to plumbthe beam

4. Loosely attach the upper and lower foot brackets to the lower rails (4a) using a 3/16" hex drive and four (4) 1/4-20 x 2" cap screws (4b).

NOTE: The lower brackets have anotched shape.

LOWER RAIL

NOTE: Support feet can be placed atbeam ends or every 12" as dictated instability guidelines and as indicated ondrawings. In some instances, beammay need to be lifted or clips temporarilyremoved to install support foot.

5a

"T" FOOT

5b 6

1/4-20 x 7/8"BINDER BOLT

NOTE: These bolts need to be securely tightened for proper function.

of 14939500366 Rev D

5. For a T foot, secure the lower columns together using a 3/16" hex drive with one (1) 1/4-20 x 7/8" binder bolt and one (1) 1/4-20 x 3/4" flat head screw (5a), and place between the foot brackets (5b). Tighten to 100 in-lbs minimum.

6. Secure the feet assemblies to the brackets using a 3/16" hex drive and two (2) 1/4-20 x 2" cap head screws, and then secure all four (4) foot bracket screws.


CLIP

1/4-20 x 3/4"FLAT HEAD SCREW

1/4-20 x 2"CAP HEAD SCREW

7a

"L" FOOT

7b

8

NOTE: These bolts need to be securely tightened for properfunction.

of 14939500366 Rev D

7. For an L foot, place the foot assembly between the foot brackets (7a) and secure using a 3/16" hex drive and two (2) 1/4-20 x 2" cap head screws (7b) and then secure all four (4) foot bracket screws.

8. With a level against the side of thealuminum extrusion, adjust the feetglides to plumb the beam.

NOTE: Check to make sure all thebeam and feet glides are onthe floor.


1/4-20 x 2"CAP HEAD SCREW

LEVEL

FEETGLIDES

2b2a

of 14939500366 Rev D

1a

NOTE: Keep protective filmfrom beam joint.

5 LOWERALIGNMENTPLATE

1/4-20 x 1/2" HEX HEAD SCREW

3

WOOD BLOCK

BEAMALIGNMENTPIN

KNURL

Connecting Beams in an In-Line Condition

1. Adjust the beam glides to match the height of the adjacentbeam (1a).

2. Insert the beam alignment pin (2a) half way into the aluminumextrusion so that only one knurl portion is visible (2b).

3. Slide the adjacent beam onto the alignment pin. NOTE: Use ofa mallet and wood block may be necessary to drive the beamstightly together.

4. Secure the adjacent beams together at the in-linebrackets using a 1/2" socket and a 5/16-18 x 1" carriagebolts and 5/16-18 hex nut via the rectangular hole.

5. Check to make sure the second beam islevel and in line with the first beam, thensecure the lower alignment plateusing a 3/8" hex head drive tooland four (4) 1/4-20 x1/2" hexhead screws. Be carefulnot to over tighten.

5/16-18 x 1"CARRIAGE BOLT

5/16-18 HEX NUT

IN-LINEBRACKETS

4

2c

of 14939500366 Rev D

90o BEAM

2a

1/4-20 x 13/16"CAP HEAD SCREW

BE

AM

LE

FT

EN

DB

EA

MR

IGH

T E

ND

NO

N E

ND

RIGHTEND

NONEND

LEFTEND

2b

90 DEGREEBRACKET ASSEMBLY

1

Connecting Beams in a 90 Degree Condition

1. Configure the 90degree off-modulebracket assembly forthe appropriate 90degree application byremoving/installingthe #10-24 x 1/2" flathead screw using a1/8" hex drive.

2. Remove thein-line bracket on theend of the aluminumextrusion by removingthe attachment screwusing a 3/16" hex drive(2a). Insert the 90degree bracketassembly into slotsas shown (2b), andloosely secure the 90degree bracketassembly with thescrew removed instep 2a (2c).

BE

AM

#10-24 x 1/2"FLAT HEAD SCREW

1/4-20 x 13/16"CAP HEAD SCREW

3a

3b

SPINE BEAM

UPPERCONNECTOR

SPACER

of 14939500366 Rev D

SIDE VIEW

3. Hang the spacer onthe side of the spine beam at the desired install location(3a), and then install theupper connector directlyover it by rotating it into position (3b).

4. Adjust the 90 degree beamglides to match the heightof the spine beam.

SPINE BEAM

UPPERCONNECTOR

of 14939500366 Rev D

90 DEGREEBRACKET

BRACKETPIN

SIDE VIEW

90 DEGREE BEAM

PINS FIRMLYENGAGED

SPINE BEAM

5b

5a

SPINE BEAMATTACHMENT HOLES

5. Slide the 90 degree beam up to thespine beam (5a) while engaging the upperconnector, and secure the 90 degreebracket screw such that the bracket pinsdraw up and firmly engage the spine beamattachment holes (5b).

NOTE: May need to lift the far end of the90 degree beam to engage the upperconnector.

90 DEGREE BEAM

3a

FLANGEOF LOWERCOVERBRACKET

LIGHT SEAL

2

of 14939500366 Rev D

3b

UPPER COVERBRACKET

SIDE VIEW SIDE VIEW

3

UPPER COVERBRACKET

2LOWER COVERBRACKET

1b

1a

Install the Covers Afterthe Power and Datais Installed

1. Remove any cover light seals that will interfere withthe end of run trims. Pull the bottom of the seal away fromthe back of the cover (1a) and then slide the seal off thebottom of the cover (1b). Retain the seal for future use.

NOTE: Covers should be installed before the end of runtrim to avoid damage to the trim.

2. Set the cover channel on the flanges of the lowercover brackets.

3. Slide the cover laterally until the left cover clip isopposite the left upper cover bracket (3a) and rotate thecover to the beam to engage the clips (3b).

NOTE: Secure the clips working from left to right.

NOTE: If desk tethers are installed prior to the skins, thetether can't be in the lowest 2 positions or else the skinscan't be installed.

of 14939500366 Rev D

5

BEAM COVER

4. To install a spine beam cover behinda 90 degree connection, begin byremoving the covers from the 90 degreebeam.

5. Slide the spine beam cover laterally onthe floor (or top of feet) until the cover isaligned with the attachment clips.

NOTE: Reverse process to remove the cover.

NOTE: Use caution to preventscratching the face of the cover.

6. Lift the cover and secure per steps 1-3 above.

90 DEGREE BEAM

END-OF-RUNUPPER SPRING CLIP

1

END-OF-RUNUPPER SPRING CLIP

ALUMINUMCHANNEL

UPPER END TRIM

2a

of 14939500366 Rev D

Installing the End of Run Trim

1. To install the upper end trim, beginby inserting the upper spring into theend of the aluminum channel.

2. Slide the trim upward until it stops(2a), then install the lower spring (2b).

PUSH INWARD TO ENGAGELOWER SPRING ASSEMBLY

2b

END-OF-RUN TRIMMOUNTING CLIP

ASSEMBLY

LOWER END-OF-RUNMOUNTING CLIP

END-OF-RUN TRIMMOUNTING CLIPASSEMBLY

IN-LINE BRACKET

EARS LOCATEDON IN-LINE BRACKET

3

LOWER END-OF-RUNMOUNTING CLIP

BEAM

GLIDENUT

4

of 14939500366 Rev D

3. To install the lower end trim, beginby pressing the upper spring on to thein-line bracket just above the ears.

4. Press the lower spring on to theglide nut.

5. Remove protective filmfrom the aluminum channel.

c:scape Beam - Amazon S3...c:scape Beam Page 1 of 14 939500366 Rev D 1/8", 3/16" HEX DRIVE 3/8" If...

Documents

Transcript of c:scape Beam - Amazon S3...c:scape Beam Page 1 of 14 939500366 Rev D 1/8", 3/16" HEX DRIVE 3/8" If...