7/27/2019 cs9701_ins_ops (1).pdf

http://slidepdf.com/reader/full/cs9701insops-1pdf 1/4

CRIMESTOPPER SECURITY PRODUCTS CS-9701

WiringMain Harness: 10 pin 18 gauge wires

Red Wire: +12Volt Power Connect to constant +12volt power source with supplied in line 10 amp fuse and fuse holder.

Black Wire: Chassis GroundConnect to body metal of the vehicle using a sheet metal screw.

 Yellow Wire: Ignition Switched "ON" and "START" +12VoltsConnect to an Ignition Wire (or fuse in the fuse box) that shows +12Volts when the key is in both the"ON" and "START" positions.

Orange Wire: (-) Negative Starter Disable Output (optional)This wire is connected to terminal 85 of a relay for the starter disable. Connect terminal 86 to the Yellowignition switched wire. Cut the vehicle starter wire. Connect one half to terminal 30 and the other half toterminal 87a.

White Wire: +12Volts Flashing Parking Light Output (optional)Connect to any parking light or to the parking light output at the back of the headlight switch. ! ! ! DONOT CONNECT TO DASH DIMMER CIRCUIT ! ! !

Brown Wire: + Siren OutputConnect brown wire to siren red wire. Connect black wire of siren to chassis ground (body metal).

Blue Wire: (-) Hood/Trunk Pin Switch InputConnect to pin switches which go to ground when hood and trunk are opened. It may be necessary toinstall your own switches.

Green Wire: (-) Door Pin Switch Input

Connect to door switches which go to ground when door is opened. A (-) negative door switch wire willread +12 volts when doors are closed.

Violet Wire: (+) Door Pin Switch InputConnect to door switches which go to +12 volts when door is opened. A (+) positive door switch wire willread (-) ground when doors are closed.

Gray Wire: (-) Negative Remote Output (optional, requires relay)Connect to terminal 85 of relay. Connect terminal 86 to +12Volts constant. Connect terminal 87 to+12volt constant or (-) ground. Connect terminal 30 to device to be activated.

Sensor Plug: 4 Pin 22 Gauge

White Wire - Negative Warn AwayBlue Wire - Negative Trigger Black Wire - Sensor GroundRed Wire - Sensor +12Volt Power The sensor supplied with this system requires no additional wiring. Simply mount the sensor in a suitablelocation and plug it in. Adjust sensitivity as necessary.

LED and Override/Valet Switch Plug: 2 Pin 22 GaugeConnect LED plug to Red Connector on module and connect Override/Valet plug to Blue connector onmodule.

7/27/2019 cs9701_ins_ops (1).pdf

http://slidepdf.com/reader/full/cs9701insops-1pdf 2/4

 Power Door Locks: 3 Pin 22 Gauge (optional)

Blue Wire (-) Negative Door Unlock OutputConnect to factory unlock relay or to relay to activate motors.

Green Wire: (-) Negative Door Lock OutputConnect ot factory lock relay or to relay to activate motors.

Red Wire (+) +12Volts ConstantConnect to terminal 86 of after market relay for activating positive, reverse polarity and after market door locking systems. DO NOT USE THIS RED WIRE FOR MAIN POWER TO ACTIVATE DOOR LOCKMOTORS.

Programming Dip SwitchesThere are 4 dip switches under the access door of the control module for pre installation programming.Dip Switch #1: Door Lock/Unlock Pulse Time ON: Pulse time = .75 secondsOFF: Pulse Time = 3 secondsDip Switch #2: Ignition Controlled Lock/Unlock ON: Lock/Unlock with ignition

OFF: "NO" Lock/Unlock with ignitionDip Switch #3: Passive Arming Locks ON: Doors lock when system arms passivelyOFF: Doors do not lock when system arms passivelyDip Switch #4: Passive / Active Arming Select ON: Alarm arms automatically 30 seconds after last door is closed (PASSIVE)OFF: Alarms arms only with remote control (ACTIVE)

Transmitter ProgrammingThis system uses code learning to learn up to 3 different transmitter codes. Follow these 4 simple stepsto program a transmitter to your system.

1. Turn ignition switch on - off - on - off - on. Siren will chirp once.2. Push the Valet/Override switch for 5 seconds until the siren chirps 3 times. Release the Valet Switch.3. Press the Large Button or button #1 of the transmitter - The Siren will chirp to confirm programming.Repeat this procedure within 5 seconds for up to 2 additional transmitters.4. Turn off ignition.Note 1: If only one transmitter is being programmed, continue holding button #1 until dash LED flashes 4times. This means the system has exited program mode. Holding the transmitter button until the LEDflashes prevents unauthorized code and noise from entering the system.Note 2: Program mode is exited automatically after 5 seconds of last code transmission or once threenew codes have been programmed. LED will flash 4 times indicating program mode has terminated.

7/27/2019 cs9701_ins_ops (1).pdf

http://slidepdf.com/reader/full/cs9701insops-1pdf 3/4

OWNERS INSTRUCTIONS:

Active Arming Mode: Press button #1 once momentarily. Alarm arms and confirms with:1 Siren ChirpLights flash onceLED lights solid then starts flashing slowlyPower locks will lock (if equipped)

Starter circuit enabled (optional)

Disarming: Press button #1 once momentarily. Alarm disarms and confirms with:2 Siren ChirpsLights flash twiceLED stops flashing (turns off)Power locks will Unlock (if equipped)Starter circuit disabled (optional)

Silent Active Arming/Disarming Mode: To Activate , turn ignition on, within 10 seconds press button #2 for 3 seconds.Siren will emit a double chirp - Silent Arm/Disarm mode is on. System will operate without siren chirps.

 Alarm will remain chirp less until Silent Mode is deactivated.To De-Ac tivate, turn ignition on, within 10 seconds press button #2 for 3 seconds.Siren will emit 2 double chirps - Silent Arm/Disarm mode is off. System will operate with siren chirps.

Passive Arming Mode: Optional Must be programmed - Consult your installer.When exiting the vehicle, upon closing the last door there will be a 30 second delay before arming. TheLED will be flashing rapidly indicating the system is in passive arming mode. After the delay, the systemwill arm and confirm with:1 Siren ChirpLights flash onceLED starts flashing slowlyPower locks will lock (if equipped & dip switch # is ON)Starter circuit enabled (optional)

7/27/2019 cs9701_ins_ops (1).pdf

http://slidepdf.com/reader/full/cs9701insops-1pdf 4/4