CS41RING

3
~ This information provided courtesy of Essex Crane Rental Corp. Toll-free Sales Line: 888-991-4100 Phone: 847-215-6500 Email: [email protected] Web: www.essexcrane.com MANITOWOC ENGINEERING CO. CRANE SPECIFICATIONS WORK SHEET Manitowoc, Wisconsin 54221 4100W SERIES-3 RINGER® DESCRIPTION APPROX. WEIGHT LB. (06) RINGER ATTACHMENT Basic 36' RINGER attachment including two end sections, two side sections, and two crawler beams with four hydraulic jacks and 36" jack pads Hydraulic power unit for jacking Front roller carrier with hook rollers Counterweight carrier with side beams and rollers (No counterweight boxes or fill) Counterweight lifting indicator Leveling gauge for roller ring Telescopic air cushioned boom stop Automatic boom stop Boom hoist wire rope Components for 130' mast, including mast support, mast stop, and upper and lower mast point (Use boom butt, open throat top, 20' insert, and 40' insert from crane attachment) Self-erecting arrangement for mast including wire rope .................................... NO. 27 BOOM ATTACHMENT 140' No. 27 boom with 40' butt, 20' insert, 40' insert, 40' open throat top with 6-32" roller bearing sheaves on one shaft, rope guides for 2 operating lines, boom angle indicator, pendant rigging, and wire rope anchor joint (Use equalizer from crane attachment) (Add operating lines separately) ......................................................... NOTE: The 4100W RINGER has been designed to comp/y with the ANSI B30.5 Code. 161,000# 30,765# A Weights and specifications subject to change without notice. ©MANITOWOC ENGINEERING CO. 1990 division of The Manitowoc Company, Inc. NOT TO BE REPRODUCED WITHOUT WRITTEN PERMISSION. May 1, 1990 Page 1 of 3 This information is for reference use only and must not be used for a specific serial numbered crane. ~, Please contact Essex Crane Rental Corp. at 847-215-6500 for further information.

description

crane

Transcript of CS41RING

Page 1: CS41RING

~ This information provided courtesy of Essex Crane Rental Corp. Toll-free Sales Line: 888-991-4100 Phone: 847-215-6500 Email: [email protected] Web: www.essexcrane.com

MANITOWOC ENGINEERING CO.

CRANE SPECIFICATIONS WORK SHEET

Manitowoc, Wisconsin 54221

4100W SERIES-3 RINGER®

DESCRIPTION APPROX. WEIGHT LB.

(06) RINGER ATTACHMENT Basic 36' RINGER attachment including two end sections, two side sections, and two crawler

beams with four hydraulic jacks and 36" jack pads • Hydraulic power unit for jacking Front roller carrier with hook rollers Counterweight carrier with side beams and rollers (No counterweight boxes or fill) Counterweight lifting indicator Leveling gauge for roller ring Telescopic air cushioned boom stop Automatic boom stop Boom hoist wire rope Components for 130' mast, including mast support, mast stop, and upper and lower mast point

(Use boom butt, open throat top, 20' insert, and 40' insert from crane attachment) Self-erecting arrangement for mast including wire rope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

NO. 27 BOOM ATTACHMENT 140' No. 27 boom with 40' butt, 20' insert, 40' insert, 40' open throat top with 6-32" roller bearing

sheaves on one shaft, rope guides for 2 operating lines, boom angle indicator, pendant rigging, and wire rope anchor joint

(Use equalizer from crane attachment) (Add operating lines separately) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

NOTE: The 4100W RINGER has been designed to comp/y with the ANSI B30.5 Code.

161,000#

30,765#

A

Weights and specifications subject to change without notice.

©MANITOWOC ENGINEERING CO. 1990 division of The Manitowoc Company, Inc.

NOT TO BE REPRODUCED WITHOUT WRITTEN PERMISSION. May 1, 1990 Page 1 of 3

This information is for reference use only and must not be used for a specific serial numbered crane. ~ , Please contact Essex Crane Rental Corp. at 847-215-6500 for further information.

Page 2: CS41RING

~ This information provided courtesy of Essex Crane Rental Corp. Phone: 847-215-6500 Email: sales@essexcranecom

Toll-free Sales Line: 888-991-4100 Web: www essexcrane com

MANITOWOC ENGINEERING CO. C R A N E S P E C I F I C A T I O N S W O R K S H E E T 4100W RINGER® Manitowoc, Wisconsin 54221

O P T I

O N S

DESCRIPTION

COUNTERWEIGHT OPTIONS Counterweight box and fill (6 required) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EACH

Counterweight box only (6 required) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EACH

FILL-N-STACK counterweight box only (6 required) . . . . . . . . . . . . . . . . . . . EACH

ATTACHMENT OPTIONS Manitowoc 15-ton swivel hook and weight ball . . . . . . . . . . . . . . . . . . . . . . . . . . . . Manitowoc 30-ton hook block with single roller bearing sheave and roller

bearing swivel hook with hook latch and swivel lock . . . . . . . . . . . . . . . . . . . . . .

Manitowoc 30-ton haok block - - same as above . . . . . . . . . . . . . . . . . . . . . . . . . . .

Manitowoc 30-ton hook block - - same as above . . . . . . . . . . . . . . . . . . . . . . . . . . .

Manitowoc 70-ton hook block with 2 roller bearing sheaves and roller bearing swivel hook with hook latch and swivel lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Manitowoc 70-ton hook block - - same as above . . . . . . . . . . . . . . . . . . . . . . . . . .

Manitowoc 70-ton hook block - - same as above . . . . . . . . . . . . . . . . . . . . . . . . . .

Manitowoc 100-ton shackle block with 3 roller bearing sheaves and roller bearing swivel shackle with swivel lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Manitowoc 100-ton hook block with 3 roller bearing sheaves and roller bearing swivel hook with hook latch and swivel lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Manitowoc 200-ton hook block with 6 roller bearing sheaves and roller bearing swivel hook with hook latch and swivel lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Manitowoc 230-ton hook block with 7 roller bearing sheaves and roller bearing swivel hook with hook latch and swivel lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Manitowoc 300-ton tandem block with duplex swivel hook and 9 roller bearing sheaves and a boom point hanger block with 3 roller bearing sheaves . . . . . .

Manitowoc 350-ton tandem block with duplex swivel hock and 12 roller bearing sheaves and a boom point hanger block with 4 roller bearing sheaves . . . . . .

WIRE ROPE {SEE CHARTS FOR LENGTH AND COMPLETE SPECIFICATIONS) Load line, 11/~ " Dia. 6 x 31 EIPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Whip line, 11/~ " Dia. 6 x 31 IPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

NO. 220 MAST SECTIONS 30' No. 22C boom butt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

40' No, 22C open throat boom top . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

20' No. 22C boom insert . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

40' No, 22C boom insert . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Ladder for mast . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

NO. 27 BOOM OPTIONS Detachable upper boom point with 1-36" roller bearing sheave with rope guard Parts for 4!~ ° offset top . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

APPROX. WEIGHT LB,

46,000#

5,000#

10,100#

1,250#

1,550# 2,000#

2,460#

1,400#

3,020#

5,100#

5,500#

5,750#

8,010#

8,820#

10,290#

11,445#

2.3#'

2.3#'

6,315#

7,315#

2,555#

4,575#

1,260# 260#

A

Weights and specifications subject to change without notice. ©MANITOWOC ENGINEERING CO. 1990

division of The Manitowoc Company, Inc. May 1, 1990 NOT TO BE REPRODUCED WITHOUT WRtTTEN PERMISSION. Page 2 of 3

This information is for reference use only and must not be used for a specific serial numbered crane. Please contact Essex Crane Rental Corp. at 847-215-6500 for further information. A

Page 3: CS41RING

~ This information provided courtesy of Essex Crane Rental Corp. Phone: 847-215-6500 Email: [email protected]

Toll-free Sales Line: 888-991-4100 Web: www.essexcrane.com

A

MANITOWOC ENGINEERING CO. Manitowoc, Wisconsin 54221

C R A N E S P E C I F I C A T I O N S W O R K S H E E T 41 0 0 W RINGER®

O P T I

O N S

DESCRIPTION APPROX. WEIGHT LB.

NO. 27 BOOM SECTIONS (USE PENDANTS FROM LIFTCRANE IF AVAILABLE 20' No. 27 boom insert . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

40' No. 27 boom insert . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Set of 4-20' pendants for 180' boom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Set of 4-40' pendants for 200' and 220' boom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Set of 4-20' and 4-40' pendants for 240' boom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Set of 8-40' pendants for 260' boom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Set of 4-20' and 8-40' pendants for 280' boom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Set of 12-40' pendants for 300' boom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Set of 4-20' and 12-40' pendants for 320' boom . . . . . . . . . . . . . . . . . . . . . . . . . . . . Set of 16-40' pendants for 340' boom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

NO. 122A JIB 40' No. 122A jib with mounting parts (28.3-ton nominal capacity) . . . . . . . . . . . . . 50' No. 122A jib with mounting parts (28.3-ton nominal capacity) . . . . . . . . . . . . .

NO. 123 JIB 30' No. 123 jib (20-ton nominal capacity) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

40' No. 123 jib (15-ton nominal capacity) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

50' No. 123 jib (10-ton nominal capacity) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

60' No. 123 jib (5-ton nominal capacity) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Jib stop, backstay, j ib adapter, and mounting parts for No. 123 jib on

No. 27 boom top . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Jib backstay pendants (To be used if jib is available from machine) . . . . . . . . . . .

BASIC RINGER OPTIONS RINGER side stops for lifting or traveling with side segments removed . . . . . . . . RINGER support system with screw jacks and pads . . . . . . . . . . . . . . . . . . . . . . . . Special paint - - machinery enamel in colors other than Manitowoc standard.

(For paint other than machinery enamel contact factory for price.) . . . . . . . . . .

3,125# 5,550#

575# 830#

1,405# 1,660# 2,235# 2,490# 3,065# 3,320#

5,340#

6,060#

1,960# 2,430# 2,900# 3,370#

975# 215#

2,115# 35,060#

Weights and specifications subject Io change without notice.

©MANITOWOC ENGINEERING CO. 1990 division of The Manitowoc Company, Inc.

NOT TO BE REPRODUCED WITHOUT WRITTEN PERMISSION. May 1, 1990 Page 3 of 3

This information is for reference use only and must not be used for a specific serial numbered crane. A Please contact Essex Crane Rental Corp. at 847-215-6500 for further information.