Crystal Shape Engineering
-
Upload
michael-lovette -
Category
Documents
-
view
422 -
download
0
Transcript of Crystal Shape Engineering
![Page 1: Crystal Shape Engineering](https://reader036.fdocuments.us/reader036/viewer/2022062503/58ed943e1a28ab8c748b46a5/html5/thumbnails/1.jpg)
Crystal Shape Engineering
Michael A. Lovette
Department of Chemical Engineering, University of California at Santa Barbara
![Page 2: Crystal Shape Engineering](https://reader036.fdocuments.us/reader036/viewer/2022062503/58ed943e1a28ab8c748b46a5/html5/thumbnails/2.jpg)
Motivation• Crystal shape effects
– Downstream processing efficiency (filtering, flowability, tabletting)• Captured by “broad” shape descriptions (aspect ratio, sphericity)
– End use functionality (catalytic activity, bio-availability)• Depend on relative areas of specific faces
• Crystal shape engineering– Optimizing crystal shapes for the given application by tailoring processing conditions
• Part of the physical property control strategy for APIs
• Factors impacting physical properties of APIs– Internal structure/intermolecular interactions, hydrodynamic environment (slurry
milling), solvent(s), supersaturation, impurities, batch/resonance time
05/03/2023 2
![Page 3: Crystal Shape Engineering](https://reader036.fdocuments.us/reader036/viewer/2022062503/58ed943e1a28ab8c748b46a5/html5/thumbnails/3.jpg)
Academic understanding
Practical understanding
batchsteady-statecoverage timestep advancementattachment/detachment
Figure 1. Typical times for crystallization processes in seconds.
Crystallization Time Scales
05/03/2023 3
![Page 4: Crystal Shape Engineering](https://reader036.fdocuments.us/reader036/viewer/2022062503/58ed943e1a28ab8c748b46a5/html5/thumbnails/4.jpg)
05/03/2023 4
Graduate Research Focus• Fundamental
– Crystal Shape Engineering, Ind. Eng. Chem. Res., 2008, 47, 9812-9833.– Reinterpreting Edge Energies Calculated from Crystal Growth Experiments, J. Cryst.
Growth, 2011, 327, 117-126.– Predictive Modeling of Supersaturation-Dependent Crystal Shapes, Cryst. Growth Des.,
2012, 12, 656-669.– Multi-Site Models to Accurately Determine the Distribution of Kink Sites Adjacent to
Low Energy Edges, Phys. Rev. E, 2012, 85, 021604.
• Application Driven (Today’s Topics)– Crystal Shape Modification through Cycles of Dissolution and Growth: Attainable
Regions and Experimental Validation, AIChE J., 2011, 58, 1465-1474.– Needle-Shaped Crystals: Causality and Solvent Selection Guidance Based on Periodic
Bond Chains, Cryst. Growth Des., 2013, 13, 3341-3352.
![Page 5: Crystal Shape Engineering](https://reader036.fdocuments.us/reader036/viewer/2022062503/58ed943e1a28ab8c748b46a5/html5/thumbnails/5.jpg)
… Problematic (Needles) Crystal Shapes
Today’s Talks
05/03/2023 5
Crystal Shape Modification through Cycles …
![Page 6: Crystal Shape Engineering](https://reader036.fdocuments.us/reader036/viewer/2022062503/58ed943e1a28ab8c748b46a5/html5/thumbnails/6.jpg)
Crystal Shape Modification through Cycles of Dissolution and Growth: Attainable Regions and
Experimental Validation
![Page 7: Crystal Shape Engineering](https://reader036.fdocuments.us/reader036/viewer/2022062503/58ed943e1a28ab8c748b46a5/html5/thumbnails/7.jpg)
Motivation• Traditional approaches for crystal shape engineering
– Chemical (solvent selection, form/salt/solvate selection, impurities)– Mechanical (slurry milling, dry milling, sonication)
• Non-chemical routes for crystal shape engineering [1,2]
– Snyder et al., developed a model for capturing the effects of performing cycles of consecutive stages of dissolution and growth (cycling) on crystal shapes
– At the time cycling was widely practiced industrially though not adequately modeled
• Understanding system dynamics from fixed point and phase-plane analyses
05/03/2023 7
[1] Yang, et al., Cryst. Growth Des. 2006, 6, 2799. [2] Snyder, et al., AIChE J, 2007, 53, 1510.
![Page 8: Crystal Shape Engineering](https://reader036.fdocuments.us/reader036/viewer/2022062503/58ed943e1a28ab8c748b46a5/html5/thumbnails/8.jpg)
Assuming convex polyhedrons (faceted growth/dissolution) [1]
and defining:
yields
Constant growth/dissolution rates (requires size independence) → independent linear ODEs with
and steady-states at
with
05/03/2023 8
Shape Evolution: Single Stages
[1] Snyder, et al., AIChE J, 2007, 53, 1510.
![Page 9: Crystal Shape Engineering](https://reader036.fdocuments.us/reader036/viewer/2022062503/58ed943e1a28ab8c748b46a5/html5/thumbnails/9.jpg)
Assuming convex polyhedrons (faceted growth/dissolution) [1]
and defining:
yields
05/03/2023 9
Shape Evolution: Single Stages
Figure 2. Dimensional variables for faceted crystal growth/dissolution.
[1] Snyder, et al., AIChE J, 2007, 53, 1510.
![Page 10: Crystal Shape Engineering](https://reader036.fdocuments.us/reader036/viewer/2022062503/58ed943e1a28ab8c748b46a5/html5/thumbnails/10.jpg)
Figure 3. Dimensionless varibles for faceted crystal growth/dissolution.
Assuming convex polyhedrons (faceted growth/dissolution) [1]
and defining:
yields
05/03/2023 10
Shape Evolution: Single Stages
[1] Snyder, et al., AIChE J, 2007, 53, 1510.
![Page 11: Crystal Shape Engineering](https://reader036.fdocuments.us/reader036/viewer/2022062503/58ed943e1a28ab8c748b46a5/html5/thumbnails/11.jpg)
• Steady-states are stable and unstable stellar nodes– Equivalent eigenvalues – Orthonormal eigenvectors
• Linear trajectories – N-1 dimensions (N = # faces)– Growth: vector connecting
initial state to steady-state– Dissolution: vector beginning
at the initial state and flowing in the direction opposite to the steady-state
05/03/2023 11
Shape Trajectories: Single Stages
Figure 4. Representative 2-dimensional trajectories for growth and dissolution.
Recommended Reading: S. Strogatz, Nonlinear Dynamics and Chaos, 1994.
![Page 12: Crystal Shape Engineering](https://reader036.fdocuments.us/reader036/viewer/2022062503/58ed943e1a28ab8c748b46a5/html5/thumbnails/12.jpg)
Snyder et al., derive recursive relationship ⇒ independent linear
difference equations:
where,
For b 1
with a single steady-state at
or similarly
where:
Steady-state is a stellar node with
05/03/2023 12
Cycling Dynamics
lc < 1 Dxg > Dxd stable slow
lc > 1 Dxg < Dxd unstable fast
![Page 13: Crystal Shape Engineering](https://reader036.fdocuments.us/reader036/viewer/2022062503/58ed943e1a28ab8c748b46a5/html5/thumbnails/13.jpg)
Properties of steady-state1. Single degree of freedom (line)2. y > 0 ⇒ Dxg > Dxd
3. y < -1 ⇒ Dxg < Dxd
4. xc not between xg and xd
Snyder et al., derive recursive relationship ⇒ independent linear
difference equations:
where,
For b 1
with a single steady-state at
or similarly
where:
05/03/2023 13
Cycling Dynamics
![Page 14: Crystal Shape Engineering](https://reader036.fdocuments.us/reader036/viewer/2022062503/58ed943e1a28ab8c748b46a5/html5/thumbnails/14.jpg)
A
B
P/i0
Same exact behavior for cycling dynamics and loan dynamics
05/03/2023 14
Fun Fact: System Dynamics in Real Life
Loan dynamics
i < 0 -> bank pays you to borrow (impossible)unstable node (l>1)
Case 1: Out of debt
A
B
P/i0
Case 2: Deeper in debt
![Page 15: Crystal Shape Engineering](https://reader036.fdocuments.us/reader036/viewer/2022062503/58ed943e1a28ab8c748b46a5/html5/thumbnails/15.jpg)
Phase Plane Analysis
05/03/2023 15
Figure Face Dxg Dxd
(a)1 2.9
0.15 0.102 1.2
(b)1 0.1
0.10 0.202 0.3
(c)1 4.4
0.10 0.202 0.3
Figure 5. Representative phase planes for growth, dissolution, and cycling. The entire phase plane can be constructed from the steady-state growth, dissolution and initial shapes.
Table 1. Conditions for Figure 5.
![Page 16: Crystal Shape Engineering](https://reader036.fdocuments.us/reader036/viewer/2022062503/58ed943e1a28ab8c748b46a5/html5/thumbnails/16.jpg)
Phase Plane Analysis: Needles
05/03/2023 16
Figure Face Dxg Dxd
(a)1 -19.1
0.10 0.252 1.0
(b)1 139.7
0.10 0.252 1.0
Figure 6. Representative phase planes for needle shaped crystals. For cycling to be an effective for abating needles requires Rd > Rg and Rd
> x0 in the needle direction.
Table 2. Conditions for Figure 6.
![Page 17: Crystal Shape Engineering](https://reader036.fdocuments.us/reader036/viewer/2022062503/58ed943e1a28ab8c748b46a5/html5/thumbnails/17.jpg)
Experimental Setup• A small quiescent crystallizer was designed with a peltier cell used to
rapidly implement stepwise temperature trajectories– Single crystals were observed using an inverted optical microscope
• Saturated solution: (1) T⇓ nucleate, (2) T↑ dissolve, (3) T↓ grow, (4) T↕ cycle– Time-lapse micrographs were used to measure growth/dissolution rates
05/03/2023 17
Figure 7. Control and setup schematic (a), photograph of peltier cell (b).
![Page 18: Crystal Shape Engineering](https://reader036.fdocuments.us/reader036/viewer/2022062503/58ed943e1a28ab8c748b46a5/html5/thumbnails/18.jpg)
Results: Paracetamol• 12 cycles of dissolution and growth: paracetamol in water. Tsat = 22°C.
05/03/2023 18
Figure 8. Paracetamol in water before (a) and after (b) 12 cycles of dissolution and growth. Scale bars are 200 mm, sg = 0.11, sd = -0.08, Dtg = 75 min, and Dtd = 25 min. A1 and A2 move farther
from the central point (smaller area) , A3 moves closer (larger area).
Axis Gg (nm/s) Gd (nm/s) Rg Rd
A1 8.0 ± 1.3 -19.2 ± 2.5 1.00 ± 0.16 1.00 ± 0.13
A2 6.4 ± 1.3 -15.6 ± 2.2 0.80 ± 0.10 0.82 ± 0.12
A3 6.6 ± 1.4 -21.9 ± 3.3 0.86 ± 0.26 1.17 ± 0.26
Table 3. Absolute and relative growth and dissolution rates, for paracetamol in water. A1 is used as the reference face.
![Page 19: Crystal Shape Engineering](https://reader036.fdocuments.us/reader036/viewer/2022062503/58ed943e1a28ab8c748b46a5/html5/thumbnails/19.jpg)
Phase Plane: Paracetamol
05/03/2023 19
Figure 9. Absolute (a) and relative (b) lengths for paracetamol in water. In (b): squares are increments along the measured trajectory, and circles are increments along the predicted trajectory. The measured values of: a2 = -0.014, a3 = 0.022 and b = 0.97 were used for the prediction. As cycling continues the reference face will become an edge or vertex.
A3
A2
A1
![Page 20: Crystal Shape Engineering](https://reader036.fdocuments.us/reader036/viewer/2022062503/58ed943e1a28ab8c748b46a5/html5/thumbnails/20.jpg)
Conclusions• Cycling dynamics were investigated and determined to be
closely related to growth and dissolution dynamics• Cycling may be an effective means to avoid high aspect ratio
crystals only for a limited set of conditions• Experiments using paracetamol in water provided quantitative
agreement with the predicted shape trajectory
05/03/2023 20
![Page 21: Crystal Shape Engineering](https://reader036.fdocuments.us/reader036/viewer/2022062503/58ed943e1a28ab8c748b46a5/html5/thumbnails/21.jpg)
Problematic Crystal Shapes:Causality and Solvent Selection Guidance
Based On Periodic Bond Chains
![Page 22: Crystal Shape Engineering](https://reader036.fdocuments.us/reader036/viewer/2022062503/58ed943e1a28ab8c748b46a5/html5/thumbnails/22.jpg)
Problematic Crystal Shapes• Qualitative description of problematic shapes
– Needle shaped crystals “needles” • Typical aspect ratios (a : b : c) = (1 : 1 : ≥100)
– Flat-plate shaped crystals “plates”• Typical aspect ratios (a : b : c) = (1 : ≥100 : ≥100)
• Needles and plates can be problematic during filtration, drying, compaction and other downstream unit operations.
• These shapes are a result of the anisotropic intermolecular interactions found in molecular organic crystals.
05/03/2023 22
![Page 23: Crystal Shape Engineering](https://reader036.fdocuments.us/reader036/viewer/2022062503/58ed943e1a28ab8c748b46a5/html5/thumbnails/23.jpg)
05/03/2023
Crystal Shapes• Stable crystals form closed polyhedrons with shapes determined by the relative
growth rates of the slowest growing set of faces– Steady-state growth shape (Frank-Chernov Condition)
• The formation of needles requires all faces with components in the needle direction (tips) to grow ≳ 100 × faster than remaining faces (surrounding faces)
23
Figure 2. Rtips 100 × R≳ sf .
b
a c
Figure 3. Two scenarios for the scaling of absolute growth rates for needles.
![Page 24: Crystal Shape Engineering](https://reader036.fdocuments.us/reader036/viewer/2022062503/58ed943e1a28ab8c748b46a5/html5/thumbnails/24.jpg)
Face Classification
05/03/2023
• Periodic Bond Chain theory– A continuous and repeatable series of
intermolecular interactions within a crystal form a periodic bond chain
– PBCs will be anisotropic for organic crystals
– PBC networks are polymorph specific
• Faces classified as F, S, or K– Flat - layered, slow - ≥ 2 PBC – Stepped - rough, fast - 1
PBC– Kinked - rough, fast - 0 PBC– The growth of S and K faces is bulk
transport limited
Figure 5. Illustrative PBC diagram.
Figure 6. F, S, and K faces for a crystal with 3 periodic bond chains.
Lovette, et al., IECR, 2008.
24
![Page 25: Crystal Shape Engineering](https://reader036.fdocuments.us/reader036/viewer/2022062503/58ed943e1a28ab8c748b46a5/html5/thumbnails/25.jpg)
Identifying PBCs• One approach is visual identification of PBCs in molecular
organic crystals– Input: atomic positions, partial charges, crystallography
05/03/2023
Color Etot (kbT)-1
Red -6.8
Cyan -5.6
Yellow -2.4
Green -0.8
Figure 7. Periodic Bond Chain diagrams for naphthalene (P21/a). Interaction strengths were calculated using the generalized amber force field with RESP fit charges. T = 300K
(00-1) (11-1)
25
![Page 26: Crystal Shape Engineering](https://reader036.fdocuments.us/reader036/viewer/2022062503/58ed943e1a28ab8c748b46a5/html5/thumbnails/26.jpg)
Spiral Growth
05/03/2023 26
• Spiral sides are edges (steps) formed parallel to PBCs
• Steps advance with velocity v, to complete a layer in time ts
Figure 8. Layered growth variables.
Figure 9. Top view of the first revolution on a square spiral. ti = 1-3.
![Page 27: Crystal Shape Engineering](https://reader036.fdocuments.us/reader036/viewer/2022062503/58ed943e1a28ab8c748b46a5/html5/thumbnails/27.jpg)
[1] Snyder and Doherty, Proc. Roy. Soc. A, 2009.
Rotation Time [1]
Spiral Growth
05/03/2023 27
• Spiral sides are edges (steps) formed parallel to PBCs
• Steps advance with velocity v, to complete a layer in time ts
Figure 8. Layered growth variables.
![Page 28: Crystal Shape Engineering](https://reader036.fdocuments.us/reader036/viewer/2022062503/58ed943e1a28ab8c748b46a5/html5/thumbnails/28.jpg)
Calculating Kink Energies• Bulk interface model used to approximate kink energies
• gic and Wi
ad are site dependent (determine shape)– Assuming hydrogen bonding in the crystal is “lumped” into the
electrostatic component
• gic,j = ½ Ej,i
• Solubility parameters provide estimates for g s,j [1]
05/03/2023 28
[1] Barton, Chem. Rev., 1975, 75, 731.Ej,i is the j component of the potential energy between neighbors in direction i for the solid.
![Page 29: Crystal Shape Engineering](https://reader036.fdocuments.us/reader036/viewer/2022062503/58ed943e1a28ab8c748b46a5/html5/thumbnails/29.jpg)
Needles• Origin
– A single PBC with fkink ≈ 5 kbT greater than remaining PBCs
• Growth rate scaling– All surrounding faces contain PBC and grow at a sparingly slow rate– Tips do not contain PBC and grow at a typical rate
• A priori categorization– Absolute: Most likely for the same “variety” of interactions in PBC«
and remaining PBCs and large differences between Ez, and Ez,i≠
– Conditional: Two types of conditional needles• Type 1: PBC« contains mostly electrostatic interactions
– needles in non-polar/non-hydrogen bonding solvents (e.g., heptane)• Type 2: PBC« contains mostly dispersion interactions
– needles in strong polar/hydrogen bonding solvents (e.g, alcohols)
05/03/2023 29
![Page 30: Crystal Shape Engineering](https://reader036.fdocuments.us/reader036/viewer/2022062503/58ed943e1a28ab8c748b46a5/html5/thumbnails/30.jpg)
Spiral Growth Model for Needles
05/03/2023 30
• PBC results in “dominant” slow moving parallel edges on surrounding faces
• Dominant spiral side in agreement with the needle direction
Figure 10. Growth spiral on needleelongated in the [010] direction. [1]
[1] Hollander et al., Food Res Int, 2002, 909.
Rotation Time (needles)
![Page 31: Crystal Shape Engineering](https://reader036.fdocuments.us/reader036/viewer/2022062503/58ed943e1a28ab8c748b46a5/html5/thumbnails/31.jpg)
05/03/2023 31
PBC diagrams: lovastatin
Line Color Ed (kbT)-1 Ec (kbT)-1 Etot (kbT)-1
Red [001] -22.1 -1.5 -23.6Mustard -4.4 -7.5 -11.8Green -3.6 -7.5 -11.0Blue -7.9 -1.2 -9.1Magenta -9.1 0.6 -8.5
(c)(a) (b)
b
c
a
Figure 11. Unit cell (a), (210) face (b), and (011) face (c) for the orthorhombic
P212121 structure of lovastatin. Lovastatin forms a needle elongated in
the c direction.
![Page 32: Crystal Shape Engineering](https://reader036.fdocuments.us/reader036/viewer/2022062503/58ed943e1a28ab8c748b46a5/html5/thumbnails/32.jpg)
Figure 12. Scatter plot of g a,g d for the 132 solvents listed by Barton.[1] Green and red points correspond to Df < 5 and
Df > 5, respectively.
05/03/2023 32
Results: lovastatinSolvent f fD,tip Df ARtoluene 3.9 2.9 1.0 3hexane 5.0 3.7 1.3 5EA 4.3 1.3 3.0 23acetone 4.6 0.8 3.8 52IPA 4.7 0.2 4.4 100ethanol 5.2 0.1 5.1 190methanol 6.0 0.1 5.8 410water 9.1 1.4 7.7 2700
Table 1. Predicted kink energies normalized by kbT and aspect ratios for
selected solvents. The highlighted values correspond to known cases.
[1] Barton, Chem. Rev., 1975, 75, 731.
![Page 33: Crystal Shape Engineering](https://reader036.fdocuments.us/reader036/viewer/2022062503/58ed943e1a28ab8c748b46a5/html5/thumbnails/33.jpg)
Experimental Shapes: lovastatin
05/03/2023 33
Figure 14. Experimental shapes of lovastatin grown in (top right
to bottom left) ethyl acetate, acetone, methanol, IPA.
(Courtesy Z. Kuvadia, UCSB)
![Page 34: Crystal Shape Engineering](https://reader036.fdocuments.us/reader036/viewer/2022062503/58ed943e1a28ab8c748b46a5/html5/thumbnails/34.jpg)
05/03/2023 34
Results: a-PABA
Table 2. Predicted kink energies normalized by kbT and aspect ratios for the 13 solvents shown to result in the
formation of needles. [1]
Solvent f fD,tip Df ARhexane 5.6 2.7 2.9 15
toluene 5.0 2.0 3.0 16
EA 6.9 1.3 5.6 220
acetone 7.9 1.1 6.8 740
hexanol 8.0 0.7 7.3 1200
DMF 8.5 0.5 7.9 2300
acetic acid 9.1 1.1 8.0 2400
DMSO 8.6 0.4 8.2 2800
IPA 9.0 0.7 8.3 3300
acetonitrile 9.6 0.9 8.8 5200
ethanol 10.1 0.7 9.4 9800
methanol 11.5 0.9 10.6 32,000
water 17.0 1.8 15.2 3.3E6
Figure 15. Scatter plot of g a,g d for the 132 solvents listed by Barton. Green and red points correspond to Df < 5 and Df
> 5, respectively.
[1] Gracin et al., Cryst Growth Des, 2004, 1013.
![Page 35: Crystal Shape Engineering](https://reader036.fdocuments.us/reader036/viewer/2022062503/58ed943e1a28ab8c748b46a5/html5/thumbnails/35.jpg)
05/03/2023 35
Results: d-mannitol
Solvent f fD,tip Df ARwater 4.6 1.2 3.4 37methanol 7.5 2.4 5.2 210IPA 9.2 3.1 6.2 590EA 11.7 4.6 7.1 1500hexane 14.8 6.9 7.9 3400toluene 14.3 6.0 8.3 4800
Figure 16. Scatter plot of g a,g d for the 132 solvents listed by Barton.[1] Green and red points correspond to Df < 5 and
Df > 5, respectively.
[1] Barton, Chem. Rev., 1975, 75, 731. [2] Ho, et al., Cryst Growth Des, 2009, 4907.
Table 3. Predicted kink energies and aspect ratios for selected solvents.
![Page 36: Crystal Shape Engineering](https://reader036.fdocuments.us/reader036/viewer/2022062503/58ed943e1a28ab8c748b46a5/html5/thumbnails/36.jpg)
Flat Plates – Work in Progress• Origin
– Two symmetry related PBCs (PBC1 and PBC2) with fkink ≈ 5 kbT greater than remaining PBCs.
• Growth rate scaling– Slow growing faces contain both PBC1 and PBC2 and grow at a
sparingly slow rate– The remaining faces may contain either PBC1 or PBC2 but not both
– these faces will grow at a typical rate.• A priori categorization
– The same categorization exists as for needles. – The same process is proposed for investigating solvents.
05/03/2023 36
![Page 37: Crystal Shape Engineering](https://reader036.fdocuments.us/reader036/viewer/2022062503/58ed943e1a28ab8c748b46a5/html5/thumbnails/37.jpg)
Hypothetical Plate System• PBC1 and PBC2 exist together only in {001} faces• PBC1 and PBC2 exist individually in other faces
05/03/2023
Color Etot (kbT)-1
Red [110, -110] -17.0
Cyan -5.6
Yellow -2.4
Green -0.8
Figure 17. Periodic Bond Chain diagrams for hypothetical plate forming system (centrosymmetric, P21/a). Due to the symmetry of this system, the Red interactions
will only be found together on {001} faces.
{001} (11-1)
37
![Page 38: Crystal Shape Engineering](https://reader036.fdocuments.us/reader036/viewer/2022062503/58ed943e1a28ab8c748b46a5/html5/thumbnails/38.jpg)
Hypothetical Plate: Shape Predictions
05/03/2023
Color Etot (kbT)-1
Red [110, -110] x
Cyan -5.6
Yellow -2.4
Green -0.8
38
x = -6.5 x = -8.5 x = -10.5 x = -17.5
Figure 18. Predicted steady-state vapor growth shapes for hypothetical system - as the strength of the red interaction increases the plate thickness decreases.
![Page 39: Crystal Shape Engineering](https://reader036.fdocuments.us/reader036/viewer/2022062503/58ed943e1a28ab8c748b46a5/html5/thumbnails/39.jpg)
Conclusions and Future Work• Criterion for rapidly identifying and categorizing the potential
for a specific molecule/polymorph to form needle or flat-plate shaped crystals have been established.
• a-PABA, lovastatin, and d-mannitol were categorized as type II, type II, and type I conditional needles, respectively.
• Anisotropic shapes which are problematic to process form due to anisotropic intermolecular interactions within molecular organic crystals. Guided solvent selection may be able to result in more isotropic steady-state shapes.
• Case studies and further work is needed for flat plates.
05/03/2023 39