CRUSH TESTER ang pl - Klimatest · ACESSORIES FOR CRUSH TESTER The realization of standard tests...
Transcript of CRUSH TESTER ang pl - Klimatest · ACESSORIES FOR CRUSH TESTER The realization of standard tests...
CRUSH TESTER Model CT-2000
The CT-2000 determines the compression strength of corrugated fiberboard and its components for Q.C. (quality control) and R&D (research and development). This equipment is absolutely user friendly and its operation can easily be done through its built-in testing software, alphanumeric back-lighted display and membrane keyboard. It offers complete statistics, a parallel port for the connection of a local printer and a RS-232 serial port for the connection to a computer. MAJOR TECHNICAL CHARACTERISTICS Capacity 4000,0 N Resolution 0,1 N Selectable testing units N, kgf or lbf Testing speed (programmable) 10 - 40 mm/min Return speed of plates 250 mm/min Stroke length (programmable) 5 - 80 mm Rupture level (programmable) 40 - 100% The CT-2000 also features lightweight cast-aluminum body, HBM high precision load cell, sturdy steel nickel-platted testing plates, heavy duty step motor, STAR accurate ball screw, built-in electronics and exclusive testing software for each test. TEST ACCESSORY REQUIRED MODEL Flat Crush Test Circular Cutter CT-CA Ring Crush Test Ring Crush Holder CT-RA Corrugated Crush Test Corrugated Crush Test Device CT-CO Concora Medium Test Concora corrugator ODC/A Pin Adhesion Test Pin Adhesion Test Device CT-AC Edge Crush Test ISO Edgewise Blocks ISO ECT Edge Crush Test TAPPI Edgewise Blocks TAPPI SCT Some tests require also the use of specific sample preparation equipment, like 2G-15 used to prepare stripe test pieces for RCT, CCT and CMT tests, and like the CAP-21 used to prepare test pieces for ECT, SCT and PAT tests (See leaflet - Accessories for Crush Tester). Power supply 220 VAC, 50/60 Hz, single phase, 200 W Dimensions 320 x 320 x 560 mm (WxLxH) Weight 50 kg
FIRMA KLIMATEST FIRMA KLIMATEST UL. PILCZYCKA 198F UL. WÓLCZYŃSKA 133 54-144 WROCŁAW 01-919 WARSZAWA TEL/FAX: 71 354 06 80/71 354 06 92 TEL./FAX: (22) 864 04 35 [email protected] [email protected] www.klimatest.com
ACESSORIES FOR CRUSH TESTER The realization of standard tests for corrugated in the Crush Tester requires the use of standard testing devices. Circular cutter model CT-CA prepares disks of 100 cm² and 10 in² for the determination of the flat crush resistance of corrugated fiberboard used in packaging cases - FCT - Flat Crush Test. Column device models SCT and ECT are used for the determination of the column resistance - SCT - Short Column Test - and ECT - Edgewise Crush Test respectively. Pin adhesion test device model CT-AC is used for determination of the adhesion resistance between liner and flutter - PAT - Pin Adhesion Test. Corrugated flutted test device model CT-CO is used for the determination of the contribution of the flutter in the column resistance - CCT - Corrugated Crush Test Cross Direction. Ring crush test device model CT-RA is used for the determination of the liner compression resistance - RCT - Ring Crush Test.
CT-RA
Applicable Standards: CIRCULAR CUTTER ISO 3035, TAPPI T-825 RING CRUSH TEST TAPPI T-822 CORRUGATED CRUSH TEST TAPPI T-824 PIN ADHESION TEST TAPPI T-821 EDGEWISE CRUSH TEST ISO 3037 SHORT COLUMN TEST TAPPI T-811 The standard accessories shown here, except for the CT-CA, are designed to just keep the test pieces in the correct testing position. The preparation of the standard test pieces demand the use of additional equipment like the 2G-15 precision sample cutter, the CAP-21 pneumatic sample cutter and the ODC-A Concora laboratory flutter.
FIRMA KLIMATEST FIRMA KLIMATEST UL. PILCZYCKA 198F UL. WÓLCZYŃSKA 133 54-144 WROCŁAW 01-919 WARSZAWA TEL/FAX: 71 354 06 80/ 71 354 06 92 TEL./FAX: (22) 864 04 35 [email protected] [email protected] www.klimatest.com