Crown sasija 5P19E; 29T05,29T07,29D10.pdf

8/10/2019 Crown sasija 5P19E; 29T05,29T07,29D10.pdf

1/44

2

4 5 6

87 9

--/ -- -

MENU

PROG.-

VOL.+VOL.-

SCANLOCK

P.P.

AV/TV0

3

PROG.+

Q . V I E W S . S .

TEXT

SUB.PAGEI N D EX H O L D

REVEALC A N C E L S I Z E

MIX

SE RVICE MANUAL

5P19E CHASSIS


2/44

Note

Note-----------------------------------------------------------------Technical specification--------------------------------------------Chassis Block Diagram--------------------------------------------IC Block Diagram ---------------------------------------------------Transistor mark ----------------------------------------------------

PCB Top/Bottom layer ---------------------------------------------Service Adjustments -----------------------------------------------Control Location ----------------------------------------------------Input and Output Terminal-----------------------------------------27-30Operation Instructions---------------------------------------------Circuit Diagram-----------------------------------------------------

2

3-678-101112-13

14-2526

31-4344


3/44

Technical Specification

SUPPLY VOLTAGE : AC 90-260V 50/60Hz

1.SYSTEM PAL / SECAM / NTSC2.CHANNELS RECEIVED 0~1993.SCANNING HORIZONTAL 15625Hz

VERTICAL 50Hz4.VISION INTERMEDIATE FREQUENCY 38.9 MHz5.SOUND INTERMEDIATE FREQUENCY 33.4 MHz B/G6.INTER-CARRIER FREQUENCY 5.5/6.0/6.5/4.5 MHz7.CHROMA IF FREQUENCY PAL 34.47 MHz8.ANTENNA INPUT IMPEDANCE 75 OHM9.CRT 29 RF/SLIM

10.VIDEO SENSITIVITY AT 30dB S/N (ACCORDING TO CCEE)VHF 48 48 dBuVUHF 51 51 dBuV(50% WHITE, 1KHz-50Hz, UNWEIGHTED, SC TRAPPED)11.FM SOUND SENSITIVITY AT 30dB S/N 25 38 dBuV12.SYNCHRONIZING SENSITIVITY 22 26 dBuV13.AGC CHARACTERISTIC 65 60 dB14.SELECTIVITY 35 30 dB15.I.F. REJECTION 50 45 dB16.IMAGE REJECTION 50 45 dB

17.AUDIO OUTPUT POWER 1khz 6 or 10 W(10% THD)18.MAXIMUM OUTPUT POWER 12 W19.THD SUPPLYING 1KHz 500mW 0.3 0.5 %TO SPKR20.MINIMUM VOLUME HUM 5 10 mVrms

NORMAL LIMIT UNIT

21.MAX. BRIGHTNESS 100% WHITE, 80 cd/m

CONTROLS MAX22.H SYNC. PULL IN 400 -400 Hz23.V.SYNC. PULL IN +5 -6 45-64 Hz24.OVERSCAN 94 88-96 %25.COLOUR SENSITIVITY 35 dBuV26.LINEARITY PAL HORIZONTAL 7/8 10/12 %

2100

+700 -600

26


4/44


30.WHITE BALANCE(9300 K, LOW BRI 80cd/m )

(SET BURST OFF OF PATTERN GENERATOR OR SET COLOUR SAT. TO MINMEASURED BY MINOLTA CA-100)

0.260 x:0.288 0.0150.302 y:0.298 0.015

31.HIGH VOLTAGE (decided by CRT Spec. ) 29 31 KV32.X-RAY RADIATION 0.2 0.2 MR/HR33.REMOTE CONTROL RECEPTION 6 5 m(30 DEGREES)34.VIDEO INPUT (AV ) 1 0.9-1.1 Vp-p35.AUDIO OUTPUT(AV-OUT) 0.55 0.5(-0.1+0.3)Vrms36.COLOUR LEVEL 90 80 %

(RED CATHODE, STANDARD PICTURE MODE, COLOUR BAR TEST PATTERN)37.POWER CONSUMPTION 90 120 W38.STANDBY POWER CONSUMPTION 2 3 W

(AT 220V AC)39.FREQUENCY RESPONSE

(1 KHz = 0dB, REF : 1.0V) 100Hz +1.5~+8.9 +3, -6 dB (TBC)10KHz -0.9~-20 +3, -6 dB

o 2 2

40.DIELECTRIC STRENGTH TEST -- 6 mArms(3 KV Vrms 2SEC)41.OPERATING WORKING VOLTAGE RANGE 82-264 84-260V42.AFC PULL IN RANGE +2.2, -1.75 +1 -0.75 MHz43.TV/AV CROSSTALK (REF : 2W) 40 dB(WEIGHTED DIN NOISE)44.PICTURE MODESTANDARD: Half Contrast, Half Bright.SOFT: 1/3CONTRAST, 1/3 Bright.RICH: MAX Contrast, Half Bright.USER: PERSONAL PREFERENCE.

45

TL T TR

TEST CONDITIONS :

TEMPERATURE : 23 C 5 CHUMIDITY : 50% +/-20

o o


5/44

OPERATION ON AC90-260V 50/60Hz MAIN SUPPLYSYSTEM: PAL SECAM BG/DK/I NTSC-M200 PROGRAMMES MEMORYFULL ON SCREEN DISPLAYBLUE SCREEN DISPLAY180 MINUTES SLEEP TIMERFULL AUTO PROGRAMREAR YUV L+R/AV IN /AV OUT OR FULL SCART/HALF SCARTSIDE AV IN/S-VHS INBLACK LEVEL STRETCHTIME SETTINGCHILD LOCKFOUR PICTURE MODE: STANDARD RICH SOFT USER

TV SYSTEM : PAL SECAM BG/DK/I NTSC-M

RECIVE FRENQUENCY COVERAGE: 45.15MHz - 863.25MHzINTERMEDIATE FREQUENCIESPICTURE I.F.: 38.9MHz

CHROMA SUBCARRIER: 34.47MHz/35.32MHzMONO SOUND I.F.: FM33.4MHz/32.4MHz/32.9MHz/34.4MHz

4 ANRENNA IMPEDANCE: 75 OHM BALANCED5 AV IN: 1 AV IN;YUV(YCbCr) IN SCART IN6 AV IN SPECIFICATION:

Y:1 .0 0 .2Vp-p 75 OHMC:0.3Vp- p 75 OHM

VIDEO IN 1.0 0.2Vp-p 75 OHM AUDIO IN APPROX 500mv

7 TUNING SYSTEM: FREQUENCY SYNTHESISED WITH 200PROGRAMMES MEMORY

8 POWER SOURCE: AC90-260V 50/60Hz9 LED INDICATORS: POWER ON OR STANDBY10 OSD LANGUAGE: ENGLISH11 CONTROLS ON TV SET

(A) FRONT PANEL- MAIN POWER SWITCH- PROG+/- SOFT TOUCH

VOL+/ SOFT TOUCH

FEATURES:

GENERAL SPECIFICATION:

1

23



6/44

12 ANTENNA INPUT: 75 OHM AERIAL JACK

13 AV INPUT: RCA SOCKET14 HAND SET POWER SUPPLY: BATTERY 3V(UM-3/R6/AAA) 215 HAND SET WEIGHT: 100g(APPROX.)16 AUDIO OUTPUT: >6W or >10W (1KHz 0.5V , INPUT 10% THD)17 SPEAKER: 8 OHM 15W/ 6OHM 15W18 POWER CONSUMPTION: 120W19 COLOUR PICTURE TUBE: RF/ SLIM20 PACKING: 1SET PER 1 GIFTBOX21 ACCESSORIES: OWNER S MANUAL IN ENGLISH WITH BRAND

NAME AND WITH MODE NO. REMOTE HANDSET

'

0

22 DIELECTRIC STRENGTH TEST(3KV rms 60 SEC) 6mA rms

23 OPERATING T EMPERATURE RANGE: BEST 10 T O 424 AC LINE CORD PLUG: VDE TYPE OR SUBJECT TO CUSTOMER REQUEST25 SAFETY : IEC-60065



7/44

Chassis Block Diagram

3

4

5

6

A B C D

6

5

4

3

T D A 9 3 8 4

- -

I n

d i

a

2

Y

U

V

R E A R A

V

S I D E

A V

S -

V H S

C

i n

A V

i n

1 0 1

I F

N I C A M

- T D A 9 8 7 4

M

T S

- T D A 9 8 5 0

A V - S W H E F 4 0 5 2

L R

A V

O U T

V

L

R

Y

C

V

L

R

R

L

V

L

R

A M P - T D A 9 8 4 2 / 9 8 4 3

L R

T O N E C O N T R O L

A U D I O

R G B 8 V

2 4 C 0 8

V -

A M P

T D A 4 8 6 3 A J

H -

D R I V E

S P L

S P R

C R T

B O A R D

2 9 "

C R T

V - -

D Y

H - -

D Y

R

O U T

G

O U T

B

O U T

P H I L I P S

U O C 2

1 3 5 V

F O R

B +

+ 4 3 V

F O R

H -

d r

i v e

+ 1 2 V

F O R

M A I N

+ 2 0 V

F O R

A M P

5 P 1 9

s i d

e

V

C V B S O U T

S L I M

P A R T

T D A 9 3 6 3

- -

A P \ M E

T D A 9 8 5 9

X U L I

A G C

W

H E F

4 0 5 2

H - o u

t

V a - o u

t

V b

- o u

t

S L I M

O R

R F


8/44

IC Block Diagram

IC601(POWER SUPPLY)STR-W6556A

IC760(2CHANNEL AUDIO AMPLIFIER WITH VOLUME CONTROL)TFA19842AJ


9/44

IC Block Diagram

IC740(UNIVERSALHI-FI AUDIO PROCESSOR FOR TV)TDA9859


10/44

IC Block Diagram

H O U T

V -

D R I V E

R O

G O

B O

B C L I N

B L K I N

F i

g .

1

B l

o c

k

d i

a g r a m

S D A

S C L

I F .

P . C

H

N T

. R S

P A L / S E C A M / N T S C

D E C O D E R

D E E M P H A S I S

A U D I

O

S W I T C H

A V L

V O L U M E

C O N T R O L

B A

S E

- B A N D

D E L A Y

L I N E

S E P

.

P L L

H -

D R I V E

2 n

d

L O O P

H -

S H I F T

V -

D R I V E

+

C O N T R / B R I G H T N

O S D / T E X T

I N S E R T

C C C

W H I T E

- P

.

A D J

.

8 0 C 5 1

C P U

I 2 C

- B U S

T R A N S C E I V E R

R

O M / R A M

T E L

E T E X T

A C Q U I S I T I O N

1 / 1 0

P A G E

M E M O R Y

T E L E T E X

T / O S D

D I S P L A Y

R

G

B

B L

Y U V

H

V

R E F

E N

H A N C E D

V S T P

W M

- D A C

V S T

O U T

I / O

P O R T S

I / O P O R T S ( 4 x )

+ 3

. 3

V

R E S E T

L E D O U T ( 2 x )

A D C I N ( 4 x )

V P E

E W

G E

O M E T R Y

G E O M E T R Y

E H T O

( E W D )

R / V / P

R G / Y B

/ U / P

B

B L

R G B / Y U V

I N S E R T

R

G

B

R E F

C V B S

S Y N C

H V

C O R

S A T U R A

T I O N

L U M A

D E L A Y

P E A K I N G

B L A C K

S T

R E T C H

I F

R O R

S O U N D

P L L

Q S S O / A M O U T

P W M S ( 4 X )

W H I T E

S T R E T C H

B L U E

S T

R E T C H

A U D I O 2

A U D I O 3

A Y

N

A U D E E M

A V L

( S N D I F )

V M O U T

V M O U T

Y

T I N T

C O N T R O L

Ic101


11/44

Transistor Mark


12/44

Maion PCB Top Layer


13/44

Maion PCB Bottom Layer


14/44

Service Adjustments1. FACTORY MODE:. FACTORY MODE:

(1) Press the keys P.P ,.P S.S and Keys on the menu in turn to enter the factory mode,press the key DISPLAY to exit. . This mode is usually for R&D and engineering department u se .

(2) Press digital keys to enter every adjust page, use PROG+/- keys to pick adjustitems, use VOL+/- keys to adjust the value.(3) Press DISPLAY to quit factory mode.

2.B+ VOLTAGE ADJUST.B+ VOLTAGE ADJUST

Measure C600A +point B+ + voltage,adjust VR641 to get proper B + voltageaccording to CRT assembly list requirement.

3. RF AGC VOLTAGE ADJUST. RF AGC VOLTAGE ADJUST

(1)Receive 294.25MHz, 60dBcolor bar signal.(2)Enter factory mode and pr ess digital key 4.(3) Measure tuner AGC point vol tage, adjust AGC item till the v oltage is 2.4V,or till

picture noise just disappears4 FINE ADJUSTINE ADJUST

(1) FOCUS ADJUST1) FOCUS ADJUST

a. Receive cross-hatch pattern signal

b. Set picture to RICH mode

c. Adjust FBTs FOCUS knob till picture is clear

(2) SCREEN VOLTAGE ADJUST(KEY 0 )2) SCREEN VOLTAGE ADJUST KEY 0 )

a.

a.

Set picture to STANDARD mode without signal input;b. Enter factory mode and press digital key0,there will be a level bright line on the

scree.c. adjust the level bright line till it just can be seen, press PROG+ key to enter other

menu

(3) HORIZON ADJUST(KEY 1 ):3) HORIZON ADJUST KEY 1 ):

Receive 50HZ monoscope PATTERN. Set TV to standard mode. Press KEY1 to enter factory mode

b. Adjust 5HSH(for 60Hz picture,it s is 6HSH)to set picture hori zontal center to CRT horizontal center.

c. Receive 60HZ monoscope PATTERN, repeat above b item


15/44

a. Menu OSD position adjustment: Receive 50/60HZ cross hatch pa ttern.Set TV standard status. Press KEY 2 in factory mode, adjust

5VOF/6VOF and HOF item, to obtain menu OSD at the center of CRT

screen;

b. LOGO position adjustment: Re ceive 50/60HZ cross hatch pattern. Set TVstandard status. Press KEY 7 in factory mode, adjust

XMIN,XMAX,YMIN, and YMAX item, to obtain LOGO at the center

upto 1/3 of CRT screen.

4-6-3 TELETEXT OSD position adjustment: Receive 50/60HZ TELETEX Tsignal. Set TV standard status. Press KEY 7 in factory mode, adjust

TXMI and 5TYM/6TYM item, to obtain INDEX at the center of CRTscreen.

6 White Balance Adjustment (Applied in factory)hite Balance Adjustment Applied in factory KEY 3EY 3

6VSH 60HZverticalcenter 6VAM 60HZ vertical s ize

a. Receive 50Hz cross hatch signal,set TV to STANDARD mode, adjus t 5VSLso that pictures vertical line is just at the bottom of the ha lf picture.

Adjust 5SCL to set proper verti cal linearity, Adjust 5VSH to se t picture verticalcenter to CRT center.b. Adjust 5VAM to obtain pictures vertical re-display ratio more than 90% .

. Receive 60Hz cross hatch s ignal, repeat above (1),(2).C

d

.

If necessary, fine adjust above items.e. Receive 50HZ RGB or YUV cross hatch signal,set TV to STANDAR D

mode,adjust 5RGH till picture hor izontal center is at the CRT c enter.(OPTION)

f. Receive 60HZ RGB or YUV cross hatch signal, The TV is set to the standard

mode in the factory menu, adjus t 6RGH till picture horizontal c enter is at the CRT

center.(OPTION)

Instruction The parts with * should be adjusted according to whether the TV hasRGB or YUV functipon.

(5) OSD POSITION:5 OSD POSITION:

Service Adjustments


16/44

Service Adjustments(7) Focus adjust7 Focus adjust

Check the color purity of CRT , if the color purity is badness, please adjust it asthe following items again.

a. incept point signal, make sure the TV is set to be dynamic.

b. Loosen the assemble magnetism patch fastness nip, turn the red and the

blue magnetism ring, make the two points folded at the center of the screen.

d. Take the fastness wedge of the deflexion winding DY off, lean the deflexionwinding in the level and the vertical directions gently in order to get a favorablemoving assemble, which can make the points at the edge of the screen clearer,and rotate the fastness nip finally.

e. Insert the fastness wedge and fix it up, first, insert the left at the bottom one,

then the left at the bottom, the right at the top and the left at the top ones.

c. Rotate the red blue-green whisht assemble magnetism ring, make the red,

blue and the green point folded at the center of the screen.

5 E2PROM INITIALIZTION

(1) E2PROM initialization (KEY 8 )

We can use an empty E2PROM when making the sample TV or repairing,also can use theE2PROM which has been full of data,but you must follow t he steps below to initialize the E2PROM.

Press the keys P.P , S.S and in turn to enter the factory mode Press KEY 8,VOL +/- in turn, you

may see the OSDBUSY after the INIT on the screen About a while, the character BUSY will disappear then POWER OFF and ON the TV, the initialization is completed

(2) FUNCTION SETTING (KEY 5 )Press the keys P.P , S.S and in turn to enter the factory mode Press KEY 5 to enter the setting menu b.Set values to OPTION 1- OPTION 7c.LOGO setting when powered on or no signal Press key SCAN in factory menu to enter the LOGO editmode there are two rows the 1 st can set the customer's name etc and the 2 nd row can set to display the

customer's e-mail, phone Press the keys PROG +/- to select the character to edit use keys VOL+/-to choose the charater.


17/44


18/44


19/44


20/44


21/44


22/44


23/44


24/44


25/44


26/44

CONTROL PANEL BUTTONS

Power Connection

Rear View of the TV Set

(AC 220V50/60 Hz).

1. Video / Audio input for playback for VCR.

2. Video / Audio output for TV program.

Connect the aerial or cable TV plug to the Antenna Input Socket located at the back of the TV andconnect the cable plug coming out from the TV out socket located at the devices (VCR, DVB, etc.) to thissocket as well.

Video And Audio Input/ Output Terminals

Connections To The Antenna Input Socket

Only use the adaptor supplied with this product, connect the AC plug to the socket at the back of the TV.This TV must be operated only from the type of power source indicated on the marking label

1. Power Button2. Power Indicator & Remote Sensor 3. Speakers4. AV/TV Button5. MUTE Button6. Menu Button7. Volume Down/Up Button8. Program Down /Up Button9. AV In (Option)

AV Out (O pt io n)YUV (Y, Cb, Cr) In (Option) An tenna In put Sock et (7 5 ohm)

10. AC Power Cord11.Side AV In( Option)

S-Video(Option)

1 23

10 9

3

4

5

6

7

7

88

11

Control Location


27/44

Input and Output Terminals

Connecting the Aerial(or Cable Television Network)

75 ANT

CableTelevisionNetwork

To view television channels correctly ,a signalmust be received by the set from one of thefollowing sources:

*An outdoor aerial*A cable television network

Plug the aerial or cable network input cable tothe 75 coaxial socket on the rear of the

television.

VIDEO

LEFT

RIGHT

AV IN

AV OUT

VIDEO

LEFT

RIGHT

VCR

Decoder/video game device

Video disc player

Camcorder

Satellite receiver

VCR

TV

Satellite receiver

V

L

R

V

L

R

V

L

R

V

L

R


28/44

VCR


Video disc player

Camcorder

Satellite receiver

V

L

R

V

L

R

L

R

L

R

YC YC

S-VIDEO

L

R

L

R

Y

Cb

Cr

Y

Cb

Cr

VIDEO

LEFT

RIGHT

AV IN

LEFT

RIGHT

YCbCr IN

LEFT

RIGHT

Y

Cb

Cr

Connecting the Audio/Video Input/Outputs(option)



29/44

VCR


Video disc player

Camcorder

Satellite receiver

PERITELEVISION

VCR

TV

Amplifier

21 PIN SCART



30/44

PERIPHERAL EQUIPMENT CONNECTIONS

Aerial socket

Audio/ Video in sockets

There is a wide range of audio and video equipment that can be connected to your TV.Connection diagrams at the end of this section show you where the different equipment should beconnected at the backside of the TV.

1. Connect the RF out socket of the VCR to the aerial socket on the back of the set.2. Connect the aerial cable to the RF aerial in socket of the VCR.3. Select the program number where the VCR channel is stored.

4. Press the PLAY button on the VCR.

1. Connect the audio/video out sockets of the VCR t o audio/video in sockets of the set.2. Pres s the AV/TV button t o select AV.3. Press the PLAY button on the VCR.The VCR playback picture appears on the screen.

Precautions when connecting to other equipmentsWhen using external equipment with this TV, please read the instruction manual of the external

equipment.Switch off all power supplies to the equipment and TV before connection. Always ensure that the input and output terminals are corr ec tly connec ted. .

Note: If you wantto watch the signals from the input jacks on the f ront panel,disconnectthe Euro scart socket of the VCR from the Euro scart socket on the back of the set.



31/44

USING THE REMOTE CONTROL

Batteries

Precautions when using batteries

Precautions when using the remote control unit

NOTE:

Please follow the below instructions to install the supplied batteries into the remote control to make itoperate.

1. Remove the battery cover.2. Insert two 1.5V ( AAA size) batteries making sure

The polarity (+ or -) of the batteriesmatches the polarity marks inside the unit.

3. Replace the battery cover.

Do not use old and new batteries together.Do not use different types of batteries (for example, Manganese and Alkaline batteries)together.Note that there are chargeable and non-chargeable batteries. Do not attempt to chargenon-chargeable batteries.If the remote control unit is not used for a long period of time, remove the batteries

Do not drop the remote control unit.Do not subject the remote control unit to physical shocks.Keep the remote control unit dry. Wetting it may cause the unit to malfunction.Replace the batteries with new ones when operation of the unit deteriorates.

If there is an object between the remote control and the signal remote controlsensor window on the TV, the remote may not operate. Please make sure the remotecontrol is aiming at the remote control sensor window on the TV.

Operation Instructions


32/44

1.POWER (STANDBY) BUTTON ( )

2. MUTE BUTTON ( )

3.DIGIT BUTTONS (0-9)

4. PROGRAM SELECTION BUTTONS (--/---)

5. AV/TV BUTTON (AV/ TV)

Option

Press this button to turn the TV on/off. Pressany Number Button or Program Up/DownButton will also switch on t he TV from standbymode.

Press this button to temporarily cut off thesound output, press it again to restore thesound level.

Press the number for your desired programand the program indicator will be displayedon the screen. To select a single-digitprogram, press the corr esponding number key 0 - 9 button on the remote control unit.

Press --/--- key to select one to three digitsentry. If you want to select 0 - 9 programchannel other than using the Digit Buttons,please press "--/---" key until display "-" onthe screen right-top corner, then press digitalnumber key 0-9.If you want to s elect 10-99

program channel, please press "--/---" keyuntil display "--" on the screen right-topcorner, then press digital number key 0-9.If you want to select 100-200 program channel,please press "--/---" key until display "---" onthe screen right-top corner, then press digitalnumber key 0-9.

Inputs can be set for TV or AV mode. Pressthis button to display external video signalsuch as DVD, VCR or VCD video player. AVwill be displayed on he screen. Press t hisbutton again to switch back to TV signal from AV.

:In TELETEXT mode, used as LANG.Key.

Remote Control Buttons

2

4 5 6

87 9

--/---

MENU

PROG.-

VOL.+VOL.-

SCANLOCK

P.P.

AV/TV0

3

PROG.+

Q. VI EW S .S .

TEXT

SUB.PAGEI ND EX H OL D

REVEALCANCEL SIZE

MIX



33/44

6. PROGRAM UP/DOWN BUTTONS (PROG. +/-)

7. VOLUME UP/DOWN BUTTONS (VOL.+/-)

8. MENU BUTTON (MENU)

Option

Press the Program Up Button to select the programforwards.Press the Program Down Button to selectthe program backwards.

Press Volume +/- Buttons to adjust sound level.

Press "MENU" button to display the OSD (On-Screen Display) menu for adjusting the image,sound and functions. Pressing this button again toout from the OSD.Please refer to page 15-19 for the details.

: In TELETEXT mode, Press this button to

swith the teletext type such west/east type.9. PERSONAL PRESETS BUTTON (P.P.)

10.QUICK VIEW BUTTON (Q.VIEW)

11. DISPLAY BUTTON ( )

12. SLEEP TIMER BUTTON ( )

You can select USER, STANDARD, SOFT or RICHmode by pressing thisbutton.

Press this button to return to the previously viewedprogram.

Press this button sequentially to display the currentprogram number, color s ystem and sound systemon the screen.

If you do not set the time, " --:--" will display on thescreen

Press the "Sleep Timer" button on your remotecontrol to start setting the automatic sleep timer.Press the button to adjust the time i n increments of

30 minutes, from 0 to 180 minutes. When the presettime runs to 0, TV set will go into standby mode. Toswitch off this function, press this key step by step

l d l d h

2

4 5 6

87 9

--/---

MENU

PROG.-

VOL.+VOL.-

SCANLOCK

P.P.

AV/TV0

3

PROG.+

Q. VI EW S .S .

TEXT


REVEALCANCEL SIZE


MIX



34/44

The TV set can provide the locked key for control or prevent your children from watching the program.

Press the "LOCK" button on remote control unit.The key locked symbol( ) will be displayed on thescreen for five seconds and entered into the childlocked mode. While in Lock mode, any keys on theTV set will be disabled. Except the key on theRemote control

Press again the 'LOCK" button on the remote controlunit to cancel this function.

Press the SCAN button to automatically browseevery channel which you have stored.

Press this button to select the correct sound system

5.5M 6.0M 4.5M 6.5M

In NICAM mode, press this button to change thesound station.

In TV mode, the(GREEN) / (BLUE) buttons has thesame function as PROG+/- buttons; the (RED)/(YELLOW)buttons has the same function as VOL+/-button.In TELETEXT mode, press these colour buttons ,the

13.LOCK BUTTON

SETTING UP THE CHILD LOCK FUNCTION:

RELEASE CHILD LOCK:

14.SCAN BUTTON

15.SOUND SYSTEM BUTTON(S.S)

16.STEREO/MONO DUAL(CHI/II)(TELETEXTOPTION)

17.COLOUR BUTTONS(RED/YELLOW/GREEN/BLUE)(TELETEXT OPTION)

2

4 5 6

87 9

--/---

MENU

PROG.-

VOL.+VOL.-

SCANLOCK

P.P.

AV/TV0

3

PROG.+

Q. VI EW S .S.

TEXT


REVEALCANCEL SIZE


MIX



35/44

*Picture mode RICH,SOFT,STANDARD are fixedby factory, all the change of these settings will besaved into the USER mode automatically.

In TELETEXT mode, used as INDEX key.

INDEX: Press INDEX button to obtain the index page.

In TELETEXT mode, used as REVEAL key.REVEAL: Sometimes the answers of quizes, jokesetc are hidden. Press REVEAL button to revealthe hidden information.

In TV mode, used as PICTURE menu command; inTELETEXT mode, used as SIZE key.SIZE: The top or button half of any page can beenlarged by pressing this button.

In TELETEXT mode, used as HOLD key.HOLD: Sub-pages will scroll automatically. PressHOLD button a hold a sub-page.To release the page.Press HOLD again.

In TELETEXT mode, used as SUB.PAGE key.SUB.PAGE: Some pages attach sub-page,Pagenumber may contain several subpages which areautomatically paged by the TV station. Press thisbutton once.0001 will be displayed on screen, usenumber key(0-9)to look for other sub-pages if available, If there is no sub-page,**** will be

displayed. To cancel this, press this button again.

Press this button to display TELETEXT signal, mixTELETEXT page with TV signal and r eturn to TV.NOTE: To avoid mixing of External R GB while

18.INDEX BUTTON(TELETEXT OPTION)

19.REVEAL MENU BUTTON(TELETEXT OPTION)

20.SIZE MENU BUTTON(TELETEXT OPTION)

21.HOLD BUTTON(TELETEXT OPTION)

22.SUB.PAGE BUTTON(TELETEXT OPTION)

23.TEXT/BUTTON(ON/MIX/OFF)(TELETEXTOPTION)

2

4 5 6

87 9

--/---

MENU

PROG.-

VOL.+VOL.-

SCANLOCK

P.P.

AV/TV0

3

PROG.+

Q. VI EW S .S .

TEXT


REVEALCANCEL SIZE


MIX



36/44

24.CANCEL BUTTON(TELETEXT OPTION)In TELETEXT Mode, used as CANCEL key.CANCEL: If you want to watch TV but not cancelthe TELETEXT mode completely. Press theCANCEL button. When the last selected page isupdated, the page number will be appeared atthe top of the TV screen press the CANCELbutton again to reveal the page.

2

4 5 6

87 9

--/---

MENU

PROG.-

VOL.+VOL.-

SCANLOCK

P.P.

AV/TV0

3

PROG.+

Q. VI EW S .S.

TEXT


REVEALCANCEL SIZE


MIX



37/44

MENU SYSTEM

This TV allows you to adjust the settings f rom the menu screens.* In the AV mode, menus appear the same as in TV mode except the Install menu.

Picture

Sound

Features

Timer

TINT

SHARPNESS

BRIGHTNESS

COLOR

VOLUME

LANGUAGE

TREBLE

BASS

BALANCE

COLOR SYS

SOUND SYS

TIME

STOP TIME

CH SWITCH

SWITCH TO

Install

SURROUND

CONTRAST

CALENDAR

MANUAL STORE

FINE TUNE

PROG NO

AUTO STORE

SOUND MODE

GAME

START TIME

SKIP


O i I i


38/44

Picture Menu

Sound Menu

PICTURE

CONTRAST

BRIGHTNESS

COLOR

SHARPNESS

TINT

55

55

55

50

00

SOUND

VOLUME

TREBLE

BASS

BALANCE

SURROUND

SOUND MODE

51

00

00

00

OFF

STANDARD

Press the MENU button to enter the menu screens for the following

settings.

Select the desired item using the PROG. + / - Buttons.Use the VOL. +/- buttons to adjust the item settings.

The item selected will be highlighted in red* The menu screen will time out automatically after few seconds if it is left

idle on the screen.

PICTURE Menu -> SOUND Menu (option) -> FEATURES Menu -> TIMERMenu -> INSTALL Menu -> EXIT

--

" "

You can select CONTRAST, BRIGHTNESS,COLOR, SHARPNESS, and TINT items bypressing PROG. +/- Buttons, and pressing theVOL.+/- Buttons to adjust the item of which youselected.

Press the VOL. + / - buttons to enhance or reducethe contrast between objects and the backgroundfrom 00 to 100 .

Using the VOL. + / - buttons to adjust the lightnessand darkness of the picture from 00 to 100 .

Press the VOL. + / - buttons to increase or decrease

the color saturation from 00 to 100 .

Adjust the outl ine of object s to ei ther sharpen or more dull from 00 to 100 .

Adjust the color of objects fr om 50 to +50 ,making them more red or green for a more naturallook.

Press VOL +/- buttons to adjust the Volumebetween 00 and 100 .

Press VOL +/- buttons t o adjust desired Treble

1.CONTRAST

2.BRIGHTNESS

3.COLOR

4.SHARPNESS

5. TINT (NTSC Only)

1.VOLUME

2.TREBLE

" " " "

" " " "

" " " "

" " " "

" " " "

" " " "


O ti I t ti


39/44

Features Menu

FEATURESLANGUAGECOLOR SYSSOUND SYSCALENDARGAME

ENGL ISH AUTO

3.BASS

Press VOL +/- buttons to adjust desired Bass volume of sound between " " " "-10 and +10 .4.BALANCEPress VOL +/- buttons to adjust the Balance between L50 and R50 ." " " "

5.SURROUNDYou can select to turn ON or OFF the Surround.

6.SOUND MODEPress VOL +/- buttons to select the Sound Mode to STANDARD, MUSIC, THEATER, USER.

Note:TREBLE,BASS,BALANCE,SURROUND,SOUND MODE have function only for TONE-CONTROL.

1.LANGUAGE

2.COLOR SYS

3.SOUND SYS

You can change menu language in this item. PressVOL. +/- Buttons to select your desired language. All the on screen displays wi ll appear in theselected language.

Press VOL +/- buttons to change the color systemto AUTO, PAL,N4.43,NTSC,SECAM

Press the VOL.+/- Buttons, you can change theSound System to 6.0M ( I), 6.5M ( D/K), 4.5M ( M)and 5.5M ( B/G).

B/G: PAL B/G, SECAM B/GI: PAL ID/K: PAL D/K, SECAM D/KM: NTSC-M




40/44

4.Calendar (Option)

-Press VOL +/- button to enter into Calendar menu.-Press PROG +/- buttons to select Year, Month and Date. Press VOL +/- button to adjust the value.-Press MENU button again to return." "

5.Game Moving Cube (Option)Press the PROG. +/- to select the Game function under the Features Menu.Press VOL +/- buttons to enter the Game OSD (On Screen Display) menu.

Game Rules: There are total 16 levels of the game. The player will win whenmoving all the pink cubes to the red box.-Press PROG +/- buttons to move UP and DOWN, press VOL +/- to shift between right and left.-To next stage of the game, press P.P button." "-To start a new game, press MUTE ." "-To exit the game, press MENU button." "

Timer Menu

TIMERTIMESTART TIMESTOP TIMECH SWITCHSWITCH TO

-- ---- - --- - --- - ---

-

-

-

-

-

-

-

-

1. TIME

2. START-TIME

3. STOP-TIME

4. CH SWITCH

5.SWITCH TO

NOTE:

To adjust the current time by this item. Press theVOL. - button to set hour, and the VOL. +

button to set minute.

To set the time when the TV set to turn onautomatically.

To set the time when the TV set to turn off automatically.

To preset the time that the TV will switch to theselected channel (Position) automatically.

To set the program that will switch automaticallyat the CH SWITCH.

Al l the timer functions wi ll only beeffective if the power of the TV set is switchedoff using the remote control unit. If the power is switched off by the power button on the TV

t f il th ti ill

" " " "




41/44

Install Menu

INSTALL

AUT O S TOR E

MANUAL STORE

FINE TUNEPROG NO.

SKIP

00

OFF

1.

2. MANUAL STORE

3. FINE TUNE

4.PROG NO

5

Press VOL.+/- Buttons to start searching. TheVOL- button for backward search; the VOL+ buttonfor forward search. When a TV station signal isreceived, the searching will stop automatically.

You can use this FINE tuning process for fineadjustment by pressing VOL.+/- Buttons. Normallyfine tuning is only necessary if reception is poor.

Up to 200 TV channels can be stored by programnumbers (0 to 200). By pressing VOL.+/- Buttons(or number keys) in this item to select channelnumber. You can store the channel number, whichare watching, and change the channel number.Once you have preset the channels, you will beable to use the PROG. +/- or NUMBER buttons to

scan the channels you have programmed.

AUTOSTOREPress VOL.+/- Buttons,the TV setwill automaticalysearch from V-L band to U band.The channels arestored in the order in which t hey appear in thefrequency bands.

" "" "

You can skip unnecessary program channels of your choice not to be displayed during viewingand scanning when pressing the PROG -/+buttons.Select "Skip Del" by pressing VOL. + / -Buttons to select the channel that would like toskip from the channel scan operation.

.SKIP

.




42/44

TROUBLESHOOTING

The fol lowing problems do not always indicate a hardware fai lure. Therefore, please use thetroubleshooting guide below before calling for repair service. If, after following the guide none of theremedies work, unplug the TV and call for service.

Make sure the power cord is plugged in,then press POWER button.Check battery in the remote control.(Maybe batteries are dead.)

Ensure the TV power is ON (Indicatedby the green power indicator on thefront of the unit).Check antenna/ cable connections.Try different channel.

Maybe sound is muted. Try pressingVOL+ button is not set to minimum.Try another channel.Check the AV cables for disconnection.

Maybe the TV is being affected byinterference from automobiles, trains,high-voltage transmission lines, neonsigns or another sources of interference.

Try redirecting or relocating your antennato reduce the affects of the interference.Change channels to confirm if thesymptom is still present.

Try another channel.Check antenna connections.If using VCR, check TV/VCR button. Adjust fine tuning contro l.Probably local interference, such as anappliance.

When the VCR test signal (TSG) isreceived, the lower side of the testpattern is distorted as shown in thefigure. This is not a malfunction and the

Problem Checks and Adjustments

TV will not turn on

No picture, no sound

No sound, picture OK

Spots on the screen (Snow)

Poor reception of broadcastchannels

VCR




43/44

Check for any obstacle between theremote control and the remote controlsensor window.Maybe batteries are dead. Try replacingbatteries with new ones.Check for incorrect battery orientation.

Please change the direction, height or positionof the antenna. Reflections frombuilding or mountains might cause thisphenomenon. A highly directionalantenna may improve the reception.

Check whether all the picture adjustmentshave been properly performed.Enter into the (Picture mode) inside themenu to select a different picture set-up.

Remote Control does not operate

The picture is doubled or tripled(GHOST)

Degraded colours or tints



44/44

Crown sasija 5P19E; 29T05,29T07,29D10.pdf

Documents

Transcript of Crown sasija 5P19E; 29T05,29T07,29D10.pdf