COR Configuration on Cisco Call Manager Express
-
Upload
gilles-de-paimpol -
Category
Documents
-
view
220 -
download
0
Transcript of COR Configuration on Cisco Call Manager Express
-
8/10/2019 COR Configuration on Cisco Call Manager Express
1/4
Unified Communication
Tuesday, 18 September 2012
COR Configuration on Cisco Call Manager Express
The class of restrictions (COR) functionality provides the ability to deny certain call attempts based on the
incoming and outgoing class of restrictions provisioned on the dial peers. This functionality provides flexibility
in network design, allows users to block calls (for example, international numbers), and applies different
restrictions to call attempts from different originators.
COR is used to specify which incoming dial peer can use which outgoing dial peer to make a call. Each dial
peer can be provisioned with an incoming and an outgoing COR list. The incoming COR list indicates the
capability of the dial peer to initiate certain classes of calls. The o utgoing COR list
indicates the capability required for an incoming dial peer to deliver a call via this outgoing dial peer. If the
capabilities of the incoming dial peer are not the same or a superset of the capabilities required by the
outgoing dial peer, the call cannot be completed using this outgoing dial peer.
Configuration
!
voice class codec 1
codec preference 1 g711ulaw
!
Trunk group for logical grouping of ports, configuration and joint management of multiple Ports
trunk group FXO
voice-class cause-code 1
hunt-scheme longest-idle
!
Below frequency & cadence values used in UAE. You guys can get from your local provider because its vary
from provider to provider.
voice class custom-cptoneUAE-Default
dualtone disconnect
frequency 400cadence 400 350 225 525
!
voice-port 0/1/0
trunk-group FXO
supervisory disconnect dualtone mid-call
supervisory custom-cptoneUAE-Default
input gain 14
timeouts interdigit 2
timeouts call-disconnect 3
timeouts wait-release 3
caller-id enable
connection plar 203
! (PLAR) is a feature used to automatically connect an endpoint to a predetermined destination number as
soon as the line goes off-hook Like receptionist number)
voice-port 0/1/1
trunk-group FXO
supervisory disconnect dualtone mid-call
supervisory custom-cptone UAE-Default
input gain 14
timeouts interdigit 2
timeouts call-disconnect 3
timeouts wait-release 3
connection plar 203
caller-id enable
!
voice-port 0/1/2
trunk-group FXO
supervisory disconnect dualtone mid-call
supervisory custom-cptone UAE-Default
input gain 14
timeouts interdigit 2
timeouts call-disconnect 3
timeouts wait-release 3
connection plar 203
caller-id enable
Muhammad
Nawaz (CCIE
VOICE/SEC/SP)
View my complete
profile
About Me
2013(3)
2012(8)
September(3)
COR
Configurati
on on Cisco
CallManager
Express
Digit
Manipulatio
n on Voice
Gateway
FXO Port
Configuration on Voice
Gateway
August(5)
Blog Archive
Ce site utilise des cookies permettant de fournir les services. En utilisant ce site, vous acceptez l'utilisation des cookies. En savoir plus OK !
Page 1 sur 4Unified Communication: COR Configuration on Cisco Call Manager Express
25/12/2014http://uctime.blogspot.fr/2012/09/cor-configuration-on-cisco-call-manager.html
-
8/10/2019 COR Configuration on Cisco Call Manager Express
2/4
!
voice-port 0/1/3
trunk-group FXO
supervisory disconnect dualtone mid-call
supervisory custom-cptone UAE-Default
input gain 14
timeouts interdigit 2
timeouts call-disconnect 3
timeouts wait-release 3
connection plar 203
caller-id enable!
We have to create condition like internal, mobile, and international under dial-peer cor custom. Same Like
Partition in CUCM. Then we will use these conditions in outgoing & incoming corlist dial-peers.
!
dial-peer cor custom
name internal
name local
name national
name mobile
name international
!
Below are the o utgoing calls Corlist dial-peer configurations and will assign to outgoing dial-peers later.
dial-peer cor listinternalmember internal
!
dial-peer cor listlocal
member local
!
dial-peer cor listnational
member national
!
dial-peer cor listmobile
member mobile
!
dial-peer cor list international
member international
!
Below are the incoming Corlist dial-peers same like CSS in the CUCM. These cor list dial-peers will
assign to ephon-dn in CUCME configuration.
dial-peer cor listRestricted
member internal
dial-peer cor listLocalCalls
member internal
member local
!
dial-peer cor list LongDistance
member internal
member local
member national
member mobile
!
dial-peer cor list International
member internal
member local
member nationalmember mobile
member international
!
dial-peer voice 1 pots
trunkgroup FXO
corlist outgoinglocal
destination-pattern 9[19]..
forward-digits 3
!
dial-peer voice 2 pots
trunkgroup FXO
corlist outgoinglocal
destination-pattern 9[2-8][0-9][1-9]....
forward-digits 7
!
dial-peer voice 3 pots
trunkgroup FXO
corlist outgoingmobile
destination-pattern 905[056].......
prefix 05
Page 2 sur 4Unified Communication: COR Configuration on Cisco Call Manager Express
25/12/2014http://uctime.blogspot.fr/2012/09/cor-configuration-on-cisco-call-manager.html
-
8/10/2019 COR Configuration on Cisco Call Manager Express
3/4
Posted byMuhammad Nawaz (CCIE VOICE/SEC/SP)at22:36
!
dial-peer voice 4 pots
trunkgroup FXO
corlist outgoingnational
destination-pattern 90[234679].......
prefix 0
!
dial-peer voice 5 pots
trunkgroup FXO
corlist outgoinginternational
destination-pattern 900Tprefix 00
!
dial-peer voice 6 pots
trunkgroup FXO
corlist outgoinglocal
destination-pattern 9600T
prefix 600
!
dial-peer voice 7 pots
trunkgroup FXO
corlist outgoinglocal
destination-pattern 9800T
prefix 800
!
We want to give full access to managers phone thats why we have assigned the corlist international to
Managers Phone.!
Ephone-dn 1 dual-line
Description Manager Phone
Number 100
Corlist incoming international
!
We want to give long distance access to common employees. So these guys can call within country
thats why we have assigned the corlistnationalto these guys.
!
phone-dn 2 dual-line
Description common employees
Number 150
Corlist incoming national
!
We want to give local calls access to pantry phones. So these phones can make local calls .thats why we have
assigned the corlistlocalto these guys.
Ephone-dn 3 dual-line
Description Pantry Phone
Number 155
Corlist incominglocal
!
We want to give internal calls access to Lobby phones. So these lobby phones can only make internal
calls.thats why we have assigned the corlist Restrictedto these phones
!
Ephone-dn 4 dual-line
Description Lobby Phone
Number 200
Corlist incomingRestricted
!
Troubleshooting
You can use the Debug voip caapi inout commandfor verification. This will allow you to see which
dial-peer is matching
+1 Recommend this on Google
3 comments:
Askar Ali Khan 10 December 2012 at 23:06
Nawaz thanks for sharing.
Reply
Anonymous18 March 2014 at 02:37
Page 3 sur 4Unified Communication: COR Configuration on Cisco Call Manager Express
25/12/2014http://uctime.blogspot.fr/2012/09/cor-configuration-on-cisco-call-manager.html
-
8/10/2019 COR Configuration on Cisco Call Manager Express
4/4
Newer Post Older PostHome
Subscribe to:Post Comments (Atom)
Comment as:
Publish Preview
Hi,
how could we implement that above dial plan in case of DAFZA where we need to Press 9 to get dial
tone,than again Press 9 to go dial out
Reply
Anonymous20 March 2014 at 12:34
use secondary-dialtone 9
Reply
Simple template. Template images by gaffera. Powered byBlogger.
Page 4 sur 4Unified Communication: COR Configuration on Cisco Call Manager Express
25/12/2014http://uctime blogspot fr/2012/09/cor configuration on cisco call manager html